Description of instrument panel indicators on Renault Logan

03/04/2022 47,966 Renault

Author: Ivan Baranov

The device that the Renault Logan dashboard has is quite standard. However, it is not always possible to understand the indicators that are on it. Also, the process of dismantling and installation has certain nuances. You can find out all about this in our article.

[Hide]

Renault Logan dashboard description of indicators

The design of the ventilation system nozzles is unusual, but at the same time practical, since such a design has an increased ability to correctly distribute air flows inside the cabin, thereby facilitating the operation of the air conditioner. Among the main controls present on the panel and causing some criticism from demanding Renault Logan owners are the regulators: after starting the engine, the indicator should go out.

If the light is constantly on, let the engine idle for a minute or two - the temperature should drop. If the light remains on, check the cooling system; 10 - not used; 11 - parking brake and low fluid level indicator for Renault Logan, the instrument panel in the hydraulic brake system reservoir lights up red when the parking brake is applied and the brake fluid level in the reservoir is low; 12 - the turn signal lights up with a flashing green light when the left or right turn signal of the Renault Logan instrument cluster is turned on when the alarm is triggered; 13 - When the ignition is turned on, the engine management system malfunction warning lamp lights up orange and then goes out.

If the lamp is constantly on, then you need to contact a service station. Alarms are not used on auto parts; 14 — the immobilizer status indicator lights up red.

It not only has one place for installing a radio with a radio in a basic car, but in others two air flows with deflectors are already installed. Under the radio on the center console there is its own instrument panel with controls. There is a button for turning on the heated rear window, control buttons for the left and right window lifts and knobs for adjusting the tightening direction. There is also a fan temperature control and an air conditioning control knob, if installed.

There is a panic button on the center console instrument panel. Over the past two years, the Renault Logan car has undergone a number of changes for the better. The Renault Logan instrument cluster also affected the interior.

To remove them from memory and exit the self-diagnosis mode, the Renault Logan instrument panel follows the button located on the instrument panel for several seconds.

This mode allows you to know instantaneous consumption, even when the car is stationary. Controls and instrument panel 1.

Side deflector. Side air nozzle. Control Panel.

Logan 1 dashboard icons

The first generation was released in 2006 and has been actively used by motorists since then. Indicators and icons on the vehicle's dashboard display the status of the modules in real time and warn the driver of breakdowns or errors.

The car has a minimum set of basic and additional equipment, which allows you to limit the number of indicators and instruments.

A special feature of the icons is that when the engine starts, all icons light up simultaneously and go out after 10 seconds. In addition, each lamp belongs to only one circuit.

Description of the icons on the Renault Logan 2 dashboard

The second modification of the car has been produced since 2014 and differs from the first generation in its improved design. The order of the car remained the same. All lights and icons remained in their original places and retained their original appearance and meaning.

Logan 3 dashboard icons

The third generation saw more global changes. The trim design has changed a lot, adding modern trim and some edging. It is noteworthy that no new equipment or systems appeared in the car. Common icons have the same meaning and appearance.

Video about replacing the dashboard

1 - Tachometer (scale division unit - 100 rpm).

2 - Fuel level indicator.

3 - Multifunction display: odometer, trip odometer, time setting or on-board computer.

4 - Coolant temperature gauge.

5 — Speedometer.

6.— Signal light for turning on the rear fog lights.

— Signal light for turning on the front fog lights.

— Warning light for door not closed.

7 - Multifunction button:

Controlling data output to the display. When you briefly press the button, you switch from the total mileage/time display to the trip mileage/time display or vice versa. Resetting the trip odometer to zero. Display the trip odometer readings, press the button and hold it down for a while. Setting the exact time.

— Signal light for minimum fuel level in the tank.

— Signal light for turning on the direction indicators.

— Coolant temperature warning light.

— Warning light for low engine oil pressure.

— Warning light for electronic engine immobilizer.

— Signal light for electronic system malfunction/signal light for preheating (diesel engine).

— Warning light for low battery.

— Warning light for the exhaust gas emissions reduction system.

— Signal light for parking brake activation and brake system malfunction.

— Signal light for low beam headlights.

— Signal light for turning on the high beam headlights.

— Signal light for anti-lock braking system malfunction.

— Airbag warning light.

— Warning light for unfastened driver's seat belt.

— Signal light for disabling the front passenger airbag.

— Signal light for turning on the heated rear window.

Renault Logan is a budget, but practical and multifunctional car. This is clearly evidenced by the ergonomic instrument panel, which is equipped with a considerable number of sensors, indicators and various lights. They participate in the management and control of transport, monitor the condition of vehicle systems and mechanisms, and regulate various processes in them. But even highly practical elements eventually become unusable, and sensors and fuses burn out. In this case, you will need to replace the light bulbs in the dashboard, which, if you know the features, you can do it yourself.

All models (with 1.4 and 1.6 l engines) and generations (2005-2009, restyling 2009-2016, 2014-2017) were created with special attention to a modern, sophisticated and optional type of tidy.

You can find many photos online that show the designations of all the indicators, lamps and torpedo icons, as well as a video with a detailed description of the functions.

We study the icons on the dashboard of Renault Logan 2

The instrument panel of Renault Logan 2 has a standard device. Yet it is not always easy to understand their designations. Especially if this is your first time behind the wheel of a Renault Logan 2. It is the dashboard that will be discussed in this material.

On-board computer Renault Logan 2
On-board computer information
Description of Logan Dashboard Icons 2
Conclusion
Video

On-board computer Renault Logan 2

activating the on-board computer (BC) of Renault Logan 2 is easy by pressing the button located at the end of the lever responsible for the washing machine and windshield wiper. If you press again, the operating modes of the Renault Logan 2 BC will be displayed on the instrument panel display.

To reset the readings (except the odometer), press and hold the same button for at least 3 seconds.

Trip computer information

Odometer. Data on the total mileage of Renault Logan 2 is automatically displayed on the instrument cluster after starting the internal combustion engine and does not work to reset it.

What does the on-board computer show?

Day running. Shows total daily mileage since last reset. The limit is 999.9 km.
Time is displayed in 24-hour format.
Total fuel cost. Represents the total offset since the last reset.
Average fuel cost. As is already clear, they show how much fuel is consumed on average. The number displayed on the Renault Logan 2 dashboard display is calculated based on fuel consumption and kilometers traveled since the battery was turned on or since the last reset. Immediately after updating the meter data, the driver will see the following message on the display: “—L / 100.” The jurisdictional limit is 999.9 liters. However, to get accurate information about the average cost of a Renault Logan 2, you will need to drive at least 500 km.
Distance to fuel outlet. The approximate mileage is calculated based on the average speed and current fuel consumption. The distance before running out of fuel is automatically calculated and updated while driving.
Mileage after rebooting the computer. The dashboard displays the total mileage of the Renault Logan 2 after resetting absolutely all computer readings. The ripening limit is 999.9 km.
Average speed. This dashboard mode displays the average driving speed since the information was last reset.

Replacing light bulbs

Instructions for pinout the board and connection diagram, as well as the location of elements on the dashboard for Logan depend on the year of manufacture. You should only disassemble the panel, change indicators, and replace lamps if you have experience and knowledge of the technical features of the car. Firmware and wire layout may vary depending on the configuration.

To replace faulty light bulbs and indicators, you must remove the panel. The disassembly procedure is as follows:

Remove the casing on the steering column; to do this, remove the bolts from its body;
Take out the cladding, the fastenings of which are the clamps;
Remove the screws securing the casing from the bottom;
After removing the cover, unscrew the screws located on both sides;

After replacing non-functioning elements with new ones, assembly is performed in the reverse order.

Changing indicators and lamps yourself, disassembling the instrument panel and changing the colors of light bulbs does not cause any difficulties for the average driver. On the Internet you can find a large number of step-by-step instructions and guides to action, which describe in sufficient detail disassembling the panel, removing faulty elements, changing the color of the lamps from red to any other, removing plugs and other parts of the torpedo.

Do not forget that when carrying out any repair work, before you start using the car, you should test the panel and set the correct characteristics. Failure to perform a performance test may affect driving safety.

Today, not a single civilian car can do without an instrument panel. The practical Renault Logan is no exception. If the owner needs to dismantle or install this integral attribute of the interior, then performing the procedure will not cause any particular difficulties. In this article you will learn everything about the instrument panel description and symbols, including a description of the indicators.

Possible malfunctions and ways to eliminate them

The instrument panel of Renault Logan and Sandero is quite reliable. Device malfunctions are relatively rare. In some cases, faults in other vehicle components are mistaken for problems with the indicators.

So, for the correct operation of the speedometer, tachometer and other elements, stable operation of the corresponding vehicle sensors is required. If incorrect information is displayed, the sensors may be damaged.

In addition, a common problem with these and other cars is a violation of the integrity of the wiring, which could occur during the repair of other parts of the car. You can check the wiring using standard means.

If one of the panel elements has truly become unusable, it can be replaced separately or entirely. Bulbs are especially easy to replace, but the speedometer and tachometer will be more difficult to replace.

The video below shows the process of replacing light bulbs (Alexey Suchkov).

You can also completely disassemble the old panel and install a new one.

Renault Logan dashboard description of indicators

If the lamp is constantly on, then you need to contact a service station. Alarms are not used on auto parts; 14 — the immobilizer status indicator lights up red.

To remove them from memory and exit the self-diagnosis mode, the Renault Logan instrument panel follows the button located on the instrument panel for several seconds.

This mode allows you to know instantaneous consumption, even when the car is stationary. Controls and instrument panel 1.

Side deflector. Side air nozzle. Control Panel.

Installation instructions

New standard trim
To dismantle the old part and install a new one, you need to perform the following procedure:

first disconnect the wires from the battery, negative first;
partially remove the door seal;
remove the decorative panel from the left front pillar;
Unscrew the bolts on both sides of the panel;
then remove the small covers located at the bottom edges of the instrument panel;
there are bolts under them, unscrew them, then remove the headlight range control knob;
Unscrew the bolts that are located under the corrector handle;
remove the upper steering column cover;
unscrew the bolt, disconnect the wiring connectors, and then remove the steering column switches;
now unscrew the bolts above the column;
remove the visor of the shield;
Unscrew the shield bolts, disconnect the wiring connectors and remove it;
remove the radio;
now unhook from below and completely remove the central decorative wiring, disconnect the wires;
remove heating and air conditioning system regulators;
now dismantle the heating and air conditioning regulator, unscrew one bolt at the top and two at the bottom;
then disconnect the diagnostic connector;
completely remove the instrument panel, disconnect the wiring block;
unscrew the bolts securing the front passenger airbag, remove the wiring connector to it;
then remove the rivets from the glove box and the cover;
Installing a new panel is done in the reverse order.

On-board computer Renault Logan 2

On-board computer Logan 2 It is easy to activate the on-board computer (BC) of Renault Logan 2 by pressing the button located at the end of the lever responsible for the washing machine and windshield wiper. If you press again, the operating modes of the Renault Logan 2 BC will be displayed on the instrument panel display.

To reset the readings (except the odometer), press and hold the same button for at least 3 seconds.

Trip computer information

Odometer. Data on the total mileage of Renault Logan 2 is automatically displayed on the instrument cluster after starting the internal combustion engine and does not work to reset it.

What does the on-board computer show?

Day running. Shows total daily mileage since last reset. The limit is 999.9 km.
Time is displayed in 24-hour format.
Total fuel cost. Represents the total offset since the last reset.
Average fuel cost. As is already clear, they show how much fuel is consumed on average. The number displayed on the Renault Logan 2 dashboard display is calculated based on fuel consumption and kilometers traveled since the battery was turned on or since the last reset. Immediately after updating the meter data, the driver will see the following message on the display: “—L / 100.” The jurisdictional limit is 999.9 liters. However, to get accurate information about the average cost of a Renault Logan 2, you will need to drive at least 500 km.
Distance to fuel outlet. The approximate mileage is calculated based on the average speed and current fuel consumption. The distance before running out of fuel is automatically calculated and updated while driving.
Mileage after rebooting the computer. The dashboard displays the total mileage of the Renault Logan 2 after resetting absolutely all computer readings. The ripening limit is 999.9 km.
Average speed. This dashboard mode displays the average driving speed since the information was last reset.

Sources

https://maslo-5w30.ru/avto/raspinovka-shhitka-priborov-reno-logan
https://nd-avtodrom.ru/raznoe/panel-priborov-reno-logan-opisanie.html
https://soloserv.ru/avto/panel-priborov-reno-logan-opisanie-indikatorov-oboznacheniya-znachok-kardiogrammy
https://loganlogan.ru/articles/panel-priborov-reno-logan-opisanie-indikatorov.html
https://aeroche.ru/obzory/opisanie-indikatorov-na-paneli-priborov-renault-logan-i-sandero-oboznacheniya-i-remont-schitka
https://NewLogan.ru/panel-priborov-reno-logan-opisanie-indikatorov-oboznacheniya-znachok-kardiogrammy.html
https://r-ro.ru/sistema-tormozov/znachki-na-pribornoj-paneli-reno-logan.html
https://rsc-53.ru/pro-rul/reno-logan-panel-priborov-opisanie.html

Color designations

When driving a car, the main thing is to understand what the signal that appears warns about, for example, a red color indicates a serious malfunction, so you need to be as careful as possible in eliminating this problem, and until it is resolved, the signal will not disappear. In addition to the red indicator, there are orange and yellow ones, they warn that a certain element requires repair or maintenance. Therefore, if a yellow light comes on, it is advisable to eliminate the reason why it came on as soon as possible; you can do this yourself, or contact a specialist.

The Renault Duster dashboard also has green and blue indicators, which signal to the driver that the vehicle is working properly.

Vanguard S&P 500 ETF ticker VOO.

VOO is good at capturing a large space and charging a small fee. It is also large and liquid, with a huge asset base and millions of shares changing hands in most cases. The fund also tracks its index very well.

The VOO ETF offers excellent US large-cap coverage. The fund competes directly with SPY and IVV, which track the same index. While all 3 funds have minimal holding costs, VOO often holds a subtle edge.

The fund reinvests bridge money, unlike SPY. The ETF is technically part of Vanguard's larger portfolio, which includes S&P 500 mutual fund classes, with little impact on VOO investors. For 2022, the fund brought its investors a solid profit of more than 18% with a meager commission of 0.03%.

Tidy pinout

There may be two types of contact groups on the device designed to power the panel. In the first case, it is a black connector, where each contact is responsible for a specific device:

1 – immobilizer and ECU control;
2 – overheating of the power plant;
3 – empty;
4 – catalyst/particulate filter failed;
5/6 – activated when PTF is turned on;
7 – body weight;
8 – input signal from the fuel tank float;
9 – phase from the battery;
10 – power supply to the device from the ignition switch;
11 – positive terminal of dimensions;
12 – positive terminal of the antifreeze temperature sensor;
13 – battery charging;
14 – oil pressure lamp;
15 – turn signals;
16 – indicator of hand brake operation;
17 – turning on the heated windshield of the aft part;
18/19 – turning on high/low beam headlights;
20 – airbag malfunction;
21 – tachometer;
22 – speedometer;
23 – call the BC display menu;
24 – positive terminal from the gas tank float.

In more advanced configurations of the machine there is also an additional equipment connector:

1/2 - empty;
3 – airbag blocking;
4/11 – not applicable;
12 – doors are not closed;
13/16 – negative terminal of the ABS device;
14/15 – empty;
17/18 – not applicable;
19 – fuel level signal;
20/24 – empty.

( 1 rating, average 4 out of 5 )