Replacing the windshield wiper of Lada Kalina hatchback (VAZ Kalina) with your own hands

Beginning of work

To install a windshield wiper relay with an adjustable pause with your own hands, you must first dismantle the wipers. Their design may vary significantly depending on the vehicle model. It is also worth noting that the brushes can be front or rear. However, regardless of their type, the relay is located on the vehicle glass.

If there is no wiring diagram for the wipers, you can find the installation location of the control unit yourself. To do this, you need to inspect the base of the brushes. Most often, in foreign and domestic cars, this element is screwed to the car body.

Most often, the relay is located near the hood release handle. When the part is found, it is dismantled. To do this you need to prepare a simple screwdriver. The old relay is removed very carefully. You must try not to scratch the body or damage other elements of the system. You also need to remove the wiper column.

When is it necessary to replace windshield wipers in Kalina?

Over time, owners of practical Lada Kalinas notice the appearance of brush marks on the surface of the windshield. Such “artifacts” create an obstacle to good visibility. In this situation, the indicated components will need to be replaced, and the trapezoid will likely need to be replaced

Many experienced owners advise purchasing frameless brushes, which, in their opinion, are able to “bravely” withstand temperature changes and can demonstrate a relatively longer service life of approximately 1.5 million cycles

Before replacing, you should understand the required size of the products. For Lada Kalina, you should purchase a driver's side brush with a length of 600 mm, and for the glass area opposite the passenger - 400 mm. For stern glass, the brush has a standard parameter of 360 mm. This wiper needs to be replaced much less frequently, since the intensity of its work is significantly lower compared to the front components.

Video “Detailed instructions for repairing an electric motor at home”

A detailed guide on the topic of repairing the wiper motor is given in the video below (the author of the video is the Auto Electrician HF channel).

The windshield cleaning system on your car should be serviced periodically. This is necessary for its proper operation, because the system can fail at the most inopportune moment. To prevent this from happening, you need to follow a few simple recommendations. Let's look at how the wiper motor is serviced and repaired, what are the weak points of the system and what to pay attention to first.

Do-it-yourself troubleshooting

When the drive works when the wipers are turned on, but the wipers do not move, repairing the trapezoid in such a situation will come down to replacing the bushings.

To do this, you need to remove the trapezoid, which is located under the plastic decorative trim under the windshield. Windshield wiper repairs are carried out in the following order:

If you do not remove the trapezoid, then when installing the bushings you can bend the hinges, which will lead to improper operation of the wipers. Therefore, it is better to remove the entire trapezoid and replace it not with weight, but with emphasis.

The destroyed bushing is immediately visible. It can be simply removed using wire cutters. To insert a new one, it and the locking ring must be steamed in hot water, otherwise it will not be possible to put it all on the hinge. Before putting on the locking ring, the bushing should be treated with lubricant (for example, lithol). All disassembly and assembly work takes a maximum of 40 minutes.

But if the central bushing “flies”, then most likely the entire windshield wiper mechanism will have to be replaced. Replacing a windshield wiper trapezoid is an even simpler task than the process of removing and installing new bushings. All work is carried out according to the algorithm described above.

Naturally, a complete replacement of the windshield wiper trapezoid will cost more than repairing the windshield wiper. But it will be more reliable. New ones are almost guaranteed to last longer than refurbished ones. Although some Lada owners claim that a rebuilt and repaired Kalina wiper trapezoid can easily last two years. Well, you should always base it on whether you are willing to spend time or money.

Recommendations

Often the wipers on the VAZ 2110 begin to work poorly as a result of problems with the electric motor, and not the trapezoid. For this reason, when servicing or replacing the trapezoid, it is important to check the serviceability of the electric wiper motor.

To check the wiper motor, you need to disconnect it from the trapezoid by unscrewing the mounting nut. The motor is then connected directly to the battery or via a standard power connector. A low buzzing sound during operation is considered normal. At the same time, noise, grinding and crackling when power is supplied are unacceptable. We also recommend reading the article on how to replace windshield wiper blades. From this article you will learn about the features of replacing wiper rubber bands, as well as what you need to consider when performing this procedure.
Experts also recommend turning on different operating modes so that the engine as a whole runs for about 10 minutes. Next, you should feel the motor. Strong heating will indicate that the wiper motor will soon fail and needs to be replaced. It is also possible to repair the motor, but it is easier and faster to purchase a new device, since its cost is not high.

Finally, we note that the VAZ 2110 windshield wiper requires regular trapezoidal maintenance. At a minimum, cleaning from dirt and lubrication is necessary. This allows you to significantly increase the service life of the mechanism and reduce the load on the electric motor, increasing its service life and productivity.

The windshield wiper trapezoid is a kind of skeleton, consisting of windshield wiper rods that go to the gear motor, which, in turn, is mounted on this skeleton.

Rear wiper size Kalina station wagon

To ensure high-quality cleaning of the windshield, it is recommended to replace the wipers with new ones every season, however, in practice, drivers do this much less often. But sooner or later everyone is faced with one question: “what is the permissible size of brushes on the Lada Granta/Lada Kalina 2.”

Why did we combine these two cars? The fact is that the second generation Lada Kalina 2 is produced only in hatchback and station wagon body styles, and the Lada Granta is considered a sedan in this line. That is why Lada Kalina 2 and Lada Granta have a lot in common, including the same windshield wiper blades (1118-5205072 and 1118-5205070), windshields (2190-5206012), etc.

The operating manual indicates the standard size of windshield wiper blades for Lada Granta and Kalina 2:

driver's (left) – 60 cm.
passenger – 41 cm.

We decided to find out what is the maximum possible length of the wipers of the Lada Granta/Kalina 2. It turns out:

If you install a 61 cm long driver's brush instead of the standard one, it will touch the body, creating a knock. Maximum – 60 cm.
But the passenger side allows you to install a larger brush, the maximum possible length is 45 cm.

Thus, the maximum size of the wiper blades of these two cars is 600x450 mm. With this length, both blades on top of the windshield will be at the same level. Unlike the standard one, the longer passenger brush will completely clean the glass in the upper part, without touching the body.

Let us remind you that these Lada cars have common not only windshield wipers, but also “diseases”, for example, both cars have a squeaking clutch pedal.

Windshield wiper blades, like any parts, gradually become faulty. At first glance, this is a simple, inconspicuous detail, but it performs an important function. Purchasing a product requires certain knowledge about the operation, characteristics, and models. The quality of visibility of the road lane depends on this choice when it is raining, snowing, or dirt flies out from under the cars ahead.

Original sizes of brushes on Grant

The length of the driver's windshield wiper is 600 mm. The length of the passenger wiper is 410 mm. Fastening type - “hook” (in English hook).

Foreign manufacturers indicate the length of the windshield wiper in inches, so the suitable length for a passenger blade is 16″. Sixteen inches - 406 mm, probably because of this, brushes with lengths of both 40 and 41 cm can be installed on the right side of the Granta. If desired, you can install a passenger windshield wiper up to 45 cm, but I would recommend staying in the range of 400...410 mm.

I have added brush article numbers to the selection: they will help you find specific products in stores that sell auto parts (this is faster and, most likely, cheaper). Also, the articles will allow you to avoid compromises in the form of several centimeters in the length of the brushes - choose only what is made specifically for your car.

Finally, a comparison of prices for windshield wipers.

The wipers stopped working: the most common reasons

Over time, every car owner is faced with the fact that the wipers suddenly stop functioning. Problems that arise reveal themselves either by a complete stop or by the appearance of extraneous sounds during operation (for example, creaking).

The mechanical part of the windshield wiper is usually very reliable. Therefore, usually wipers may not work for the following reasons:

Excessive wear and tear on moving parts of the system or lack of lubrication in required areas. In order for the windshield wiper mechanism to work properly and not fail for unknown reasons, inspection and maintenance are required, albeit not too often.
Improper use of wipers. As an example, in the winter season, before turning them on, you need to unfasten them from the glass (ideally, melt the ice on them). Failure to do this may result in fuse, motor, or drive rod failure during startup.

As a rule, the cause of windshield wiper failure is often a malfunction of the electrical part of the device:

The hum of the motor is not heard, the wipers do not work (they do not move in any of the operating modes). In this case, the cause may be a malfunction of the following elements: wiring, connectors, switches or gear motor.
The wipers work, but very slowly. Most likely, the reason is also in the gear motor. The drive mechanisms may have become oxidized and rusted. Usually they need to be cleaned and lubricated or checked for correct assembly of the mechanism.
When the intermittent mode is on, the windshield wipers operate continuously. The reason is most likely a broken relay, which will have to be replaced since it is not repairable. If the wipers are working and the sound of the motor is heard, you can also diagnose a malfunction of the breaker relay.
You can hear the engine running, but the wipers don't move. In this case, the reason is most likely a break in the rod or contact elements.
The windshield wiper arm does not work. The cause of the malfunction may be oxidation or damage to the contact elements of the traction rod.
The windshield wipers do not work correctly - they do not move to their original positions. The cause of the breakdown in this case may be improper installation, problems in the contact group of the gear motor, wear or shearing of the splines on the brush drives.
The wipers do not work when the washer fluid is applied to the windows. The cause may be a broken steering column switch or defective wiring and electrical connections.

Reasons for mechanical windshield wiper failure include:

Self-unscrewing (full or partial) of the nut connecting the crank to the gear axle. Such a defect is easy to determine when the wipers are on, since the gear motor is working, but the brushes do not move.
The nut securing the wiper arm is loose or its thread has been stripped. The reason may be incorrect installation of the leash in the initial position. Avoiding this is quite simple - you need to tighten the nuts with the required torque, and before final tightening you need to put the windshield wipers in the desired position.
The wipers do not clean the glass due to a poor fit. The simplest reason is wear of the brushes themselves. The brushes simply need to be replaced. The second most common reason is poor adherence of the brushes to the glass due to mechanical interference. An option to eliminate it is to clean the wiper of foreign objects that interfere with normal pressure. But if none are found, then it is necessary to inspect the wiper mechanism, disassemble it, find and replace parts with a lot of wear.

From the above it follows that the reason that the wipers do not work can be either a malfunction of the electric motor or wiring, or a failure of the mechanical component of the vehicle unit in question. The trapezoid, the mechanism for driving and moving the wipers, is very often prone to breakdowns. Read further in the article for what to do when your windshield wiper breaks or does not work.

Possible causes of problems

Some experts argue that if the windshield wiper blades do not work when turned on, then the most common reason for this is a failed fuse. In this case, no special efforts will be required to fix the problem. You just need to open the fuse box cover (on the left under the steering column) and find the appropriate fuse. A diagram printed on the inside of the lid will help you do this.

If the wipers do not work intermittently, then the relay may have failed. It is located in the same place as the fuses. It needs to be replaced with a new one. But, as statistics provided by owners of Lada cars show, fuses or relays blow out quite rarely.

A very common reason why the Lada Kalina windshield wiper blades do not work is the destruction of the bushings. As experienced drivers say, plastic bushings fall apart very quickly - their service life is at most 3 years.

Perhaps the reason for their destruction is the quality of the plastic. But, alas, there are no other bushings. The repair kit can be found in specialized auto stores.

When the wiper drive does not work, the reason may be a failure of the motor that drives them. To find out whether the electric brush drive has really burned out, you need to check whether electricity is supplied to it. This can be done using a tester. If power is supplied, then the overheated motor needs to be replaced.

For Lada Granta, Kalina, Priora

The resistor shown in the photo is responsible for the number of strokes. Our task is to replace (using a soldering iron) it with a resistor with lower resistance. To get two sweeps of the wipers after washing the windshield, it is enough to solder a resistor with a resistance of 47 to 68 kOhm (0.25 W). To make three swings - from 70 kOhm. The result of the modernization on video:

It is worth noting that on sale you can find a wiper relay with advanced capabilities:

There is a pause adjustment, that is, you can set any time between sweeps of the wipers;
Three strokes after the washer, instead of four (there is no problem with the wipers squeaking on the glass);
After the washer, the first stroke is delayed.

However, replacing a resistor in a relay yourself will cost only 5 rubles, and a functional relay will be 70-100 times more expensive.

When do you need to change wipers on Kalina?

It often happens that the wiper drive system works, but marks remain on the windshield that interfere with normal visibility. In this case, the wipers need to be replaced. Previously, domestic cars were equipped with brushes, into the frame of which a rubber part was inserted, which cleaned the glass. But recently frameless brushes have been used.

They work better, and their resistance to different weather conditions is higher. Although frame brushes are cheaper, frameless brushes will last longer. They can operate efficiently from 1 to 1.5 million cycles.

back Failure of the power window control unit on a Lada Kalina car

Next Why Lada Kalina won't start

Tagsrepair, windshield wiper, trapezoid, brush

Let's sum it up

https://www.youtube.com/watch?v=upload

Such an important process as replacing wipers, or when changing the windshield wiper trapezoid on a LADA Kalina car, is a very simple undertaking. There is no need for special devices or fancy tools. The brushes are removed by opening the locks.

Repairing or replacing a part such as a windshield wiper trapezium appears as a more responsible job, but it is not capable of causing difficulties for an inexperienced owner of a Lada Kalina. In such situations, do not hesitate to take action.

Advertisements on NN.RU - Auto

Re-equip, lengthen the frame, truck: Valdai Gas 33104, 33106; Valdai farmer 331043, 331063; Lawn Gas 3307, 3309;.

A certified truck conversion organization invites you to: lengthen, re-extend and convert, p.

With us you can not only extend the frame to fit a body of 5.1 m, 6.2 m, 7.5 m, 9 m for Maz Zubrenok, Maz, Kamaz, Ural, Zil, Mitsubishi, Nissan.

Lengthen Kamaz under a body 7.5 m Lengthen Maz Zubrenok, Maz under a body 9 m Re-equipment of the chassis of an extended truck.

Nizhny Novgorod residents were silent for a long time about the Siberian forest fires, but then there was a reaction in our city: people decided to pay attention to it. Imagine, you wake up in the morning, open the curtains, bright sunlight bursts into the apartment, and outside the window there is a stunningly beautiful landscape

Imagine, you wake up in the morning, open the curtains, bright sunlight bursts into your apartment, and outside the window is a stunningly beautiful landscape.

Airborne Forces Day in Nizhny Novgorod went well, fun and peacefully, contrary to firmly rooted stereotypes. Our paratroopers in quiet times, like...

August 2 is the very day when the heads of the strong are covered with blue berets. The holiday in honor of the airborne troops is exciting.

How brand engine additives work

How to register the replacement of a car's power unit this year? How to register the replacement of a car's power unit this year?

Procedure for dealing with paperwork.

How to adjust the valve mechanism on the engine of a GAZ 3110 Volga? How to adjust the valve mechanism on the engine of a GAZ 3110 Volga?

Why do you need to adjust the valves on the engine?

Adjustment of the valve mechanism YaMZ 238 Adjustment of the valve mechanism YaMZ 238

Precise valve adjustment on diesel YaMZ 238:

Organizational diagram for changing the front door window regulator on the "seven" Organization diagram for changing the front door window regulator on the "seven"

Design and procedure for replacing a window regulator

Chevrolet-Niva heating system: changing the interior heater heat exchanger Chevrolet-Niva heating system: changing the interior heater heat exchanger

Recommendations for replacing the interior heater radiator

Standards for the use of fuels and lubricants at the disposal of the Ministry of Transport of the Russian Federation Standards for the use of fuels and lubricants at the disposal of the Ministry of Transport of the Russian Federation

What basic fuel standards does the Ministry of Transport offer?

Factory and actual fuel consumption for Lada Priora, reasons for overconsumption Factory and actual fuel consumption for Lada Priora, reasons for overconsumption

Declared and measured fuel consumption per

Possible causes of the malfunction and ways to eliminate them

In practice, the most common malfunction that potassium dispensers encounter is intermittent operation of the purifiers. The repair in this case comes down to replacing the system fuse, which is located in the mounting block on the left under the steering wheel. Also, the reason may be the inoperability of the relay located there - if it fails, it needs to be replaced (video author - Andrey Nikitkin).

If the wipers on Kalina do not work at all, it is necessary to diagnose the electric motor. Wiring is supplied to the motor, so first you need to diagnose the “ground” terminal, it is located next to the adsorber. If necessary, turn it off and thoroughly clean the contact area. If the performance of the motor cannot be restored, you will need to disassemble the system and replace this element. If after replacing the brushes still do not work, you need to check the steering column switch - perhaps the reason lies there.

If all these steps do not produce results, you need to check the gearbox and trapezoid; most likely, you will have to change one of these components. If the brushes function normally, but water does not flow onto the glass, and the washer reservoir is full, you need to check the functionality of the reservoir motor.

Sorry, there are no surveys available at this time.

Price issue

The cost of brushes will vary depending on the store you buy them from, as well as their manufacturer. The cheapest, frame version from the manufacturer Bosch will cost about 900 rubles, from Denso - 1200 rubles. As for frameless devices, the minimum price for a set from Bosch or SWF is 1,500 rubles, from the manufacturer TRICO Neoform - about 1,900 rubles.

Replacing the windshield wiper gear motor

Remove the “-” terminal of the battery. Use a marker or felt-tip pen to mark the position of the blades on the windshield.

Use a screwdriver to pry it off and remove the plastic cap.

Unscrew the nut securing the brush lever

Remove the leash along with the brush from the shaft

We also remove the second leash.

Using a wrench, unscrew the two screws securing the right and left facings

We take out the plug for the screw securing the left facing using a screwdriver and unscrew the two screws securing the right and left facings

Removing the left facing

Slide the motor wiring block to the right and remove it from the holder

Having released the block clamp, disconnect the block of the wiper gear motor from the wiring block.

Use a 10mm socket to unscrew the two bolts and a 10mm wrench to unscrew the cleaner mounting nut.

We take out the windshield wiper with gear motor assembly

Use a felt-tip pen to mark the position of the crank relative to the wiper bracket.

Using a 13mm wrench, unscrew the crank mounting nut and remove the crank from the gearmotor shaft

Unscrew the three bolts securing the gear motor to the purifier bracket

Remove the gear motor from the bracket

Remove the protective film from the gear motor

https://www.youtube.com/watch?v=ytpress

Use a screwdriver to unscrew the four screws

Remove the gearbox cover with gasket

If necessary, we replace the gears of the gear motor and clean the contacts of the self-stop mechanism.

We assemble and install the gear motor on the purifier bracket in the reverse order.

To install the gear motor shaft in its original position, we put the wire terminal on the “negative” terminal of the battery.

We connect the block of wires to the block of the gear motor and turn it on using the steering column switch, then turn it off and wait until the electric motor shaft stops.

In this position of the gear motor shaft, we install the crank along the previously applied mark.

We carry out further installation of the purifier in the reverse order.

Lada Kalina Hatchback -=First car=- › Logbook › The wipers do not work. Problem with gear motor

Hello everyone! I haven’t visited Drive2 for a very long time. I confess, it’s my fault (Several changes have been made to the machine in a few months =) I will write about everything in more detail in separate blog articles.

So, a serious problem suddenly overtook me. I was driving along the highway, it was raining, I turn on the wipers, they do one cycle and freeze forever... With an astonished look, I try to revive the wipers, but they are silent. I pull over to the side of the road, the first thing I do is check the transmission - everything is ok. I open the hood, visually the rack and the motor are in perfect order... thoughtfully tugging at the contacts near the engine, I took out a cloth, wiped the glass and drove quietly to my destination. I’ll tell you honestly, friends, driving in the rain with non-working windshield wipers is an extreme thing))) God forbid, someone should experience this for themselves.

Old windshield wiper motor

When I arrived home, the first thing I did was contact an electrician. He took the electric motor, simply disassembled it, reassembled it and, connecting it to power, saw that it was alive. I happily put it in its rightful place and went about my business. The next day it rains again. I turn on the wipers, they work very slowly, do 2 cycles and die again. This time I already knew roughly what the problem was, so I didn’t stop, and having already practiced extreme driving without wipers in the rain, I went to an electrician. He was again “glad” to see me with a gear motor in my hands. He took it apart again, replaced all the brushes, cleaned the contacts and the engine came to life again. When the electrician returned this engine to me, he said the following phrase: “If it dies again, it’s better to buy a new one.” Well, the man looked at nothing - after 2 weeks the motor died again. It was decided to replace this piece of iron.

New gear motor, which, unfortunately, did not fit.

I arrive at the local Phaeton auto parts store. I’m buying a gear motor for Kalina for 1,900 rubles, the toad, of course, is choking, but there’s nothing to do, you can’t drive like that in the rain. At the delivery of goods they give you a motor without a box, documents and even with a small scratch on the lid. When I asked where the equipment was, the manager replied that the supplier brought them in this form and offered a bag. D When I arrive home, the first thing I do is run to change the motor. I remove the rack, remove the motor, install a new one, connect it to the connectors, and simultaneously check its functionality. I had just started to screw the engine to the mounts when I decided to check whether the rack would fit the new engine, since it differs slightly in size from the factory one. I connect the rail and see that it does not fit the slots at all. There were ideas on how to make it fit, but reason prevailed over flights of fancy and I decided to change the gear motor in the store. 15 minutes later I’m already approaching the store’s checkout counter. As soon as the seller saw me, he asked: “Well, didn’t it fit?” I really wanted to tell him a lot about the low-quality spare parts, but I only said a modest: “Yes, can I replace it?” The store manager said that my case is not the first and that gear motors come from the factory with two types of splines - large and small. I came across just a small one, but they didn’t have a large one in stock, so I wrote a statement and my money was returned.

A box with a new gear motor =) You can immediately see that this is the original.

I drove home upset, but on the way I noticed a small store called “Samara”. I go there, there is a young girl at the checkout who happily helped me choose the right gear motor. Moreover, I got it in a branded box, with quality control marks, a guarantee and instructions for connecting, and even for 1,700 rubles. I was extremely happy when the motor fit without any problems. This is how, for relatively little money and in 3 hours of total time, I got rid of the problem with non-working wipers.

Comparison of two motors - on the right is the factory one, on the left is the new Samara one.

PS, I saw many topics on the forums with the problem of the wipers not returning to their original position. In fact, the solution is very simple - you need to adjust the splines connecting the rack and the gearmotor. You need to let the motor rotate its axis a full cycle and then insert the rack in the desired position and that’s it, the problem will be solved.

Issue price: 1,700 ₽

You are here: Home > VAZ > Kalina > Why wipers don’t work on Kalina

When do you need to change wipers on Kalina?

The procedure for replacing these devices of the windshield wiper system on Kalina is given below (author - channel In Sandro's garage).

Because You are not logged in. To come in.

Because you are not a trusted user (phone number is not verified). Enter and confirm your phone number. Read more about trusts.

Are the rods the wiper arms or the leash?

Do I hit the brushes on the counter? ¶

Well then everything is clear.

It’s just that before replacing, you should have noticed the position of the gearbox shaft on the trapezoid body, you didn’t do that, and that’s why this shit happened now ¶

back Failure of the power window control unit on a Lada Kalina car

Next Why Lada Kalina won't start

Removing and installing the Kalina windshield wiper motor

The motor itself is connected to the wiper trapezoid by 3 bolts and one nut. First, unscrew these three bolts with a 10mm head:

And then the nut that secures the trapezoid lever to the motor shaft:

And after that you can remove the motor, since there are no more fasteners:

If necessary, we replace the motor and trapezoids, or buy the entire structure assembled and install it in the reverse order. During removal, it is advisable to note the position of the trapezoid lever relative to the body, so that later you can install everything exactly the same! The price of a trapezoid assembly with a motor for Kalina is about 2,000 rubles, and individually these parts are almost equivalent.

Many Lada owners are faced with the fact that the Kalina windshield wiper trapezoid fails. It turns out this problem is quite common. Either the wipers work slowly or they touch the side pillar, although the length of the brushes is normal. And it also happens that right on the road during rain, the glass will stand in the center and the windshield wipers on the Kalina will not work.

Modernization of wiper arms for Lada Kalina 2

It is not always possible to buy a wiper arm for the first Kalina; in this case, the design can be modified. It is necessary to remove the leash and tension spring. Then drill a new hole in the metal bar of the lever closer to the brush. We install the spring using a screwdriver, clinging it to the new hole. Now the tension will be stronger, which will allow the rear wiper to clean the glass better.

Result on video:

By the way, another way to solve the problem of poor rear window cleaning is to install a frameless wiper. Let us remind you that the front wiper blades can be installed in larger sizes.

Car windshield wipers, commonly referred to as “windshield wipers,” are one of the consumable parts of all cars. They serve to remove water and dirt from the surface of the windshield, and sometimes also the rear window, that interfere with visibility. Since blades from different cars are not fundamentally different from each other, replacing windshield wipers is done the same way for all cars. Let's look at how to change them with your own hands.

Mercedes janitor

My Instagram: Twitter: VK group: .

The windshield wiper cleans the glass by supplying water from the windshield washer reservoir.

Turn on the water supply from the windshield washer reservoir even when it rains. Wipers on w140 please, why is this and how to turn off the ignition or. Such as vases, so if the second one is turned on, do not spray on the conditioner and about. This will prevent streaks from forming on the windshield.

The rear window wiper automatically wipes the glass when the windshield wiper is on and reverse gear is engaged.

Rear window wiper

The switch is located on the control panel of the center console.

1 Intermittent mode

Make sure the ignition is on

Activating the rear window wiper

Read:

Press the switch at the top 1.

If you open the sliding door or the tailgate/tailgate while the vehicle is stationary, the rear window

stops.

As soon as all rear doors are closed or the vehicle starts to move, the rear window

Turning off the rear window wiper

Press the switch at the top 1 again.

Cleaning glass with water supplied from the windshield washer reservoir

Click the switch at the top 2.

After you release the switch, the wiper will continue to operate for approximately five seconds.

Turn on the water supply from the windshield washer reservoir even when it rains. In any Mercedes, the ring finger and little finger have high beams and wipers, like on the CLs sedan. How to turn on the air conditioner for heating: temperature. This will prevent streaks from forming on the windshield.

Cleaning windows and wiper blades

Risk of injury!

The windshield wiper may start working on its own and cause injury to you.