AvtoPrivatHow to install contactless ignition on a VAZ 2106

If the ignition is adjusted incorrectly, detonation may occur during operation of the power unit. And this, in turn, can lead to a major overhaul of the engine itself.

It’s interesting that in practice, many drivers have their own opinion on how to set the ignition on a VAZ 2106. Some use what is called “by eye,” while others purchase a strobe light for this purpose. Some people don’t try to do it themselves and entrust this work to car service specialists.

To set up the ignition on a VAZ 2106 car with your own hands, use the instructions below.

Preliminary preparation

You need to take with you to the garage:

• candle key;
• key to 13;
• a voltmeter or an ordinary twelve-volt light bulb.

Contact ignition is installed on the first cylinder.

Set the ignition timing using marks of different lengths that are placed on the timing cover.

Components of the ignition system of the VAZ 2106

Previously, a distributor of the R-125B brand was installed on the car. This unit was mounted on the machine together with a carburetor marked 2103. The distributor had a special mechanical corrector in its design, and there was no vacuum regulator. The VAZ 2106 is equipped with spark plugs of type A17DV or plugs that have similar technical characteristics.

The design of the automotive system uses a VK347 type lock, equipped with an anti-theft device. The car uses a B117-A type ignition coil, which has an open magnetic circuit and is oil-filled and sealed.

The VAZ 2106 ignition is contact-based, but it is worth noting that sometimes there is also a contactless version of the system. The contact system is considered simpler in its design. VAZ contact ignition requires regular maintenance and monitoring of the condition of the contacts.

DETAILS ABOUT THE MOST IMPORTANT ELEMENTS OF THE TRAMBER DEVICE

VACUUM REGULATOR

It is this device that can change the OZ if necessary. As soon as the motor load changes, appropriate adjustments are made to the operation of the distributor device parts.

The vacuum regulator of the distributor is a closed cavity. To ensure better performance, the design is divided by a diaphragm. One cavity goes directly to the carburetor.

When a vacuum occurs, the diaphragm begins to move. As a result, pressure is exerted on the movable disk and the breaker cam. The response time of the latter is adjusted depending on the current situation.

Ignition coil and other elements

It is somewhat different in the contactless system from the one used in the classical one. The reason is the different value of the secondary voltage. Thus, when operating an internal combustion engine with a contact (including contact-transistor) ignition system, 25-30 thousand volts are required to form a spark gap. But in a non-contact system you need to generate over 30 kV, sometimes even up to 40 kV. Therefore, more turns are needed in the secondary winding.

The remaining elements are completely similar for all three designs discussed above. You choose the armored wires connecting all high-voltage circuits yourself. They can be either in a silicone or rubber shell. Contactless ignition 2107 can work with any high-voltage wires recommended by the manufacturer. Candles must be used those recommended by the manufacturer. In this case, you can again choose the brand yourself.

We carry out the adjustment ourselves

1. The first step is to install the cylinder in the correct position. Installation is carried out so that the mark on the pulley is exactly at 0 degrees.
2. Set how the slider is positioned. It should be aimed at the first pin in the cylinder.
3. Use a strobe light and make sure the ignition is working properly.
4. Make the electrical connections in the battery: minus to ground, plus to plus.
5. The sensor must be connected to the high-voltage wire on the cylinder. The mark should connect to the crankshaft pulley.
6. Start the engine at low speed (up to 800 rpm). Use a stroboscope to illuminate the pulley, and if the mark coincides with the middle mark, then the ignition is set correctly.
7. Otherwise, the engine should be turned off and the meter should be loosened. In order to decrease the angle, turn the sensor clockwise; to increase it, turn it counterclockwise. Record and test the calibration again with the ignition on.
8. Next, you should perform manipulations with the distribution sensor. Open the lid. Match the stator and rotor mark.
9. Start the engine, bring the temperature to 75-80 degrees. When the speed is 50 km/h, sharply press the gas pedal.
10. If the ignition was installed correctly, a short-term detonation will occur when you press the gas.

Also interesting: Phase sensor Niva Chevrolet symptoms of malfunction, DPRV high signal level

Then there are two possible developments: early and late ignition. Let's consider solutions for both cases:

1. In the case of late ignition, when there is no detonation, you should change the position of the sensor clockwise.
2. In the case of early ignition, when detonation lasts longer than necessary, the sensor is rotated counterclockwise.

Niva 21213 can be subject to adjustment of the starting system by the gap at the edges of the valves, if the carburetor is removed, or by the crankshaft speed directly on the car. In the first case, the gap at the location of the lower edge (in the direction of air movement) from the throttle valve is set to a width of 1.1 mm.

It is adjusted with a screw that has a 0.7 cm hexagon on the head and a slot from the shank. This operation is carried out with the cam lever turned counterclockwise from the starting system control (all the way). In the same position, the gap at the lower edge of the air damper is set to 3 mm using a screw in the cover from the diaphragm mechanism in the starting system (you need to loosen the lock nut).

The principle of powering a carburetor engine Adjusting the Niva starting system directly in the car saves time: You need to remove the air filter from the engine, pull the control lever towards you from the air damper, and start the engine. When the air damper is forced to open (by touching a flat screwdriver to a third of its full angle of rotation) using a screw (next to the lever on the axis from the throttle valve from the first chamber), the initial rotation speed is set to 2.08.mar.0 thousand.

If you have a gas analyzer, then the carburetor adjustment in the starting system part can be done based on the amount of CO (carbon monoxide) in the exhaust gases. If, with the choke control lever fully extended, the gas rate is 8%, then everything is in order. If there is less gas than this value, then the screw on the cover of the diaphragm mechanism is tightened; if there is more, it is unscrewed and repeated measurements are taken.

It is necessary to adjust the idle speed of the Niva 2121 so that there is less carbon monoxide in the exhaust gases and so that the engine runs stably. At service stations, such work is carried out with gas analyzers on the MV. In the garage, adjustments can be made using the tachometer.

What benefits can you get?

But you will get many benefits if you install an electronic ignition on the VAZ-2106 instead of a contact one. It’s better to start with the fact that any driver likes to drive more than to repair the car. But frequent replacement of the contact group or its cleaning and adjustment causes terrible hostility among motorists. Moreover, the contact can fail at any time, so you need to have a spare one with you. But the electronic system on this side is much more reliable and does not require frequent maintenance.

But the most important thing happens in the engine - the very heart of any car. His work is returning to normal. It begins to function correctly, regardless of the rotation speed. Whether at idle or at 4000 rpm, the engine runs perfectly smoothly, stably, and the air-fuel mixture ignites in a timely manner. And this improves your comfort, increases engine reliability, and most importantly, increases its service life.

Switch

The switch is necessary to create an electrical impulse by interrupting the constant flow of current from the battery to the primary winding of the coil. The BSZ VAZ 2107 uses a switching device of type 3620.3734. The working elements contained in it are ordinary bipolar transistors that open the circuit when the Hall sensor receives a signal.

Switch 3620.3734 is built according to a simple single-wire circuit in which the device body is connected to the vehicle ground and, as a result, to the negative terminal of the battery. The benefits of using this assembly instead of a traditional switch include:

• no need for maintenance or adjustment;
• high spark energy, making it easier to start the engine in the cold season, as well as the ability to use gasoline with a lower octane number;
• the presence of a stabilization system that protects the Hall sensor from voltage surges.

This switch has a drawback - poor workmanship. It happens that the device fails after a few months of use. Its design is non-demountable, so repair is impossible. Therefore, experienced owners of the “Seven” and other VAZs with a contactless ignition system bring spare switches to their cars. Fortunately, the part is inexpensive - 400-500 rubles.

Source

Removal and installation of the ignition distributor of the VAZ 2106 distributor

The ignition distributor (distributor) is removed from the VAZ 2106 car for repair or replacement. The engine of the VAZ 2106 model has a distributor of type 30.3706.

To distinguish it from distributors of other models, a mark (ring groove) is made on the shank. To remove the distributor from a VAZ 2106 car you will need: a spark plug wrench, a bit, two “7” keys, a “13” wrench, and a screwdriver. 1. Remove the tip from the spark plug of the first cylinder and unscrew it.

2. Close the spark plug hole with your finger.

3. Turn the crankshaft until the compression stroke begins in the 1st cylinder (air will begin to escape through the spark plug hole). Then, while continuing to turn the crankshaft, align mark d on the crankshaft pulley (highlighted with chalk) with the middle mark b (if you are using gasoline with an octane rating of 92 or 95) or the extended mark c (if you are using gasoline with an octane rating lower than 92). Reinstall the spark plug of cylinder 1 and connect the high-voltage wire to it.

4. Disconnect the hose from the vacuum ignition timing regulator. 5. Remove the high-voltage wires from the sockets of the distributor cover.

6. Unscrew the nut securing the distributor, remove the spring washer and plate. 7. Remove the distributor from the engine.

8. Turn over the distributor and, holding the lower nut, unscrew the nut securing the low voltage wire; remove the washer and wire. 9. Unfasten the holders and remove the cover from the new distributor.

WARNING

Before installing a new distributor on a VAZ 2106 car, check and, if necessary, adjust the gap between the contacts of the breaker.

10. Install high-voltage wires into the cover of the new distributor in accordance with the operating order of the engine cylinders.

NOTESThe operating order of the engine cylinders is: 1-3-4-2. The distributor rotor rotates clockwise. Cylinder numbers are marked on the distributor cap and on the engine cylinder head.

11. Connect the low-voltage wire to the new distributor.

12. Turn the rotor of the new distributor to a position in which its outer contact (shown by the arrow) will be directed towards the contact of the 1st cylinder on the distributor cover. NOTE

When the outer contact 2 of the rotor coincides with mark a on the cover, it simultaneously coincides with the head of screw 1 on the distributor body.

13. While holding the distributor shaft from turning, insert it into the socket on the cylinder block so...

14... so that the line passing through the spring latches is approximately parallel to the axis of the motor. 15. Secure the distributor in this position to the cylinder block without completely tightening the nut. Connect the hose to the vacuum regulator. 16. After installing the distributor on a VAZ 2106 car, check and, if necessary, adjust the ignition timing (see “Checking and adjusting the ignition timing”).

Features of UOZ

The ignition timing angle, or as it is usually designated, the ignition timing, has a number of features that must be taken into account for the stable operation of all components in the engine. The following features are noted:

• In engines that are injected, the OZ is installed independently, since the system has a similar function. The angle at the moment the motor is running is determined. The system is based on the readings of a three-dimensional function and engine load. The operating mode of the engine (winter-summer) and the speed at which the crankshaft rotates is also important. If all indicators correspond to the optimal parameters, the control system independently selects and sets the ignition timing;
• The optimal SOP for a particular engine, in turn, is determined by the speed at which the crankshaft operates. A special feature is the fact that a higher number of revolutions ensures a reduction in the time required for ignition;
• Temperature indicators also affect SOP. Low slows down oxidation processes, as a result of which the likelihood of an early ignition timing increases; high determines late ignition timing.
• The loads that the engine experiences are large and guarantee that there will be a high level of cyclic filling of the cylinder. In this case, it will be necessary to reduce the ignition timing. If this is not done, an explosion may occur in the engine, that is, detonation.

DIY installation and connection diagram

So, having made your choice, we suggest that you familiarize yourself with the necessary tools, the replacement procedure and video instructions.

Tool

From the tool you will need:

1. Key 13 - remove and install distributor
2. Screwdriver - tighten the screws.
3. Drill with a metal drill, diameter for self-tapping screws
4. Two self-tapping screws - screw the switch.
5. Keys for 10 and 8 - remove and install the coil.

How to install step by step

1. Disconnect the negative battery. Before starting work on the ignition system, disconnect the negative terminal of the battery
2. Remove the distributor cover with high-voltage wires. Removing the ignition distributor cover
3. Disconnect the high-voltage wire on the coil. Disconnecting the wire from the ignition coil
4. Using short turns of the starter, set the ignition distributor slider perpendicular to the engine. This is how the distributor should be installed relative to the engine
5. Mark the position of the distributor with a marker on the engine. Installing the ignition distributor slider
6. Unscrew the nut holding the distributor using a 13mm wrench. Disconnect the wire connecting the device to the coil. Before removing the ignition distributor, disconnect the wire that goes to it from the coil
7. Insert the new ignition distributor into the engine by removing the cover. The ignition distributor must be inserted into the standard socket
8. Turn the distributor body so that the middle mark on it coincides with the mark you previously placed on the motor.
9. Tighten the nut securing the new ignition distributor. The nut holds the ignition distributor in place
10. Put on the distributor cover and connect the wires to it. This is how the cover is installed on the distributor
11. Replace the ignition coil with a new one. A new system requires a new coil
12. Connect the original and new wires to the coil. To connect everything correctly, use the diagram. All connections must match the diagram
13. Install the switch in any convenient location. Drill holes and screw screws into them to hold the device. Check the connections of all VAZ-2106 systems. The switch will not take up much space under the hood and its location does not matter
14. Start the engine. If it doesn’t start the first time, you can turn the distributor a little. This will change the ignition timing.

Adjusting the ignition yourself

To normalize engine operation and fix problems, you need to correctly set the ignition timing of your car. Only if these conditions are met can the engine operate correctly. To diagnose and correct errors in the ignition angle, you will need the following tools:

• strobe (desirable);
• tachometer. Most often, such a tool is built into the autotester, so there should be no problems with it;
• slotted screwdriver;
• wrench 10 (socket or open-end).

Having a strobe light will make all your work much easier, so it is better to purchase it for private use.

Before you start directly adjusting the ignition timing and angle, you need to do some preparatory work. First, place the key in the ignition and start the engine. Afterwards, you need to bring the system to a temperature of 90 degrees and increase the idle speed to 800 rpm (using a tachometer) using the fuel regulator knob on the carburetor body.

Hatch in the gearbox

After the engine has warmed up, remove the silicone tube that supplies vacuum from the fitting. You will find the adjusting lever on the panel of the ignition torque distributor, otherwise called the distributor. Its base is attached to the carburetor. Place the free edge of the silicone tube close to your finger to find out if there is a vacuum. If there is one, then the finger will stick to the tube. Reduce the number of revolutions until the vacuum disappears.

Contact ignition VAZ 2106

In the photo - VAZ 2106, which is an exact copy of the Fiat 124

Different ignition systems were installed on the car at different times, but the Fiat contact design is considered a classic. Its device is incredibly simple - an ignition coil, a distributor, a bundle of high-voltage wires and the right spark plugs. This is all that is needed for the correct operation of the engine. On the first batches of sixes, until 1980, a P125-B distributor of the simplest design without vacuum adjustment of the ignition timing was installed. After installing the standard Ozone carburetor, it became possible to equip the distributor with a vacuum advance angle adjustment system.

Structurally, distributors differ only in the presence of a vacuum membrane chamber, which is connected to the primary chamber of the carburetor. At a certain period, a distributor was installed without a vacuum chamber and it was structurally similar to the old one. Reel B117-a, sealed, filled with oil, with open magnetic conductors. In short, there is practically nothing to break. All that remains is to check the condition of the system elements and you can begin adjusting.

Preparatory stage

Many people are interested in the question of how to install contactless ignition on a VAZ 2106 if there is no garage and inspection hole. But this device does not require an inspection hole; all operations can be performed near the hood. Additional auxiliary equipment required:

• Set of keys (for 8,10,13);
• Two screwdrivers - flat and Phillips;
• Pliers;
• Drill (use of drills for working with metal is allowed);
• Screws.

You can also borrow a spanner wrench that has a long handle. It will allow the crankshaft to rotate. If it is not found, then you can use the method of rotating the rear wheel, after placing the anti-recoil objects and turning on 4th or 5th speed.

When solving the problem of how to install electronic ignition on a VAZ 2106, first you need to carry out the preparation stage:

• Open the car hood;
• Remove the negative terminal of the battery;
• Remove the wires from the spark plugs and the distribution device;
• Unscrew the spark plugs.

Next, you need to prepare a new kit and begin the dismantling process.

Replacing the VAZ 2106 distributor with your own handsAutoRemka

Distributor malfunctions lead to malfunctions in the ignition system. You can guess that the distributor is faulty by such characteristic signs as sudden jerks of the car while driving and discordant operation of the engine at idle.

The essence of such a procedure as repairing or replacing a VAZ 2106 distributor is to replace the worn parts included in it.

To carry out repair work you will need:

2 7 mm wrenches, 10 and 13 mm wrenches, two screwdrivers, a hammer, a set of flat feeler gauges, mandrels for knocking out and pressing in distributor bushings (bearings), and tweezers.

When all the tools are prepared, you can start working.

1. We unscrew the 2 fastening screws that secure the connection of the distributor rotor with the support plate of the ignition timing regulator, after which we remove the rotor itself.

2. The springs and weights of the centrifugal ignition timing regulator must be marked so as not to get confused during assembly and put everything in its original place.

3. Next, use a screwdriver to remove the springs of the centrifugal regulator (a screwdriver is needed to pry off the springs).

4. While holding the nut on the moving contact screw, unscrew the nut that secures the wire ends (the capacitor wire and the wire coming from the ignition coil).

5. Now you need to unscrew the screw that secures the distributor housing to the capacitor housing, then remove it.

6. Next, unscrew the screw that secures the tip of the movable contact wire (the nut must be held in place) and remove the insulating spacer, as well as the washers (spring and 2 flat washers - insulating and metal).

7. The next step is to unscrew the two screws that connect the contact group to the movable distributor plate.

8. After unscrewing the fastening screws, remove the contact group, followed by the insulating washers located on the axis of the contact group (flat and locking).

9. Next, use a flat screwdriver to pry off the washer that insulates the spring plate of the movable contact, and remove the movable contact itself from the axis of the contact group.

10. From the axis of the movable plate of the distributor, remove the lock washer located on the fastening of the vacuum regulator rod.

11. Use a screwdriver to pry up the vacuum regulator rod and remove it from the axis of the distributor plate.

12. Unscrew the two screws that secure the vacuum regulator housing to the distributor body and remove the regulator.

14. Press out the pin that secures the low-reflection coupling from the distributor shaft, then remove the coupling, followed by the washer.

15. Remove the distributor shaft from the housing.

17. Unscrew the 2 screws that secure the bearing locking plates, remove the spring washers and remove the plates using tweezers.

18. Next, remove the movable plate assembled with the bearing from the distributor body.

19. Check the condition of the distributor shaft - there should be no visible signs of wear on the surface of its contact with the bearing.

20. We check the capacitor using for this procedure a device that measures capacitance (normal values ​​are in the range of 0.20-0.25 μF).

21. Then you should check the condition of the diaphragm of the vacuum ignition timing regulator (to do this, you need to press the rod and plug the fitting... the rod must be held by the diaphragm).

22. We inspect the contacts of the breaker - there should be no dirt, erosion or signs of burning on them. If the above-mentioned contaminants are present, the contacts should be cleaned using a velvet file (under no circumstances should sandpaper be used for this purpose) and washed with alcohol or gasoline.

23. The distributor housing bushing with signs of wear should be replaced with a new one. Pressing out and pressing of the bearing should be done using a mandrel of the appropriate diameter.

24. The distributor should be assembled in the opposite order to the disassembly order, taking into account the following features.

Upon completion of assembly, the distance between the breaker contacts should be adjusted. The gap should be from 0.35 to 0.45 mm.

The fold located on the movable plate of the distributor must be lubricated with engine oil (literally 2-3 drops of oil will be required). The same should be done with the bearing, adding a couple of drops of oil through the oiler, which is installed on the distributor body, and the splined part of the distributor shaft.

The main components of the distributor and a description of its operation

Device.

The distributor is assembled in a housing. Inside it, a contact group is mounted on a bearing: moving and fixed contacts or a Hall sensor (for contactless ignition). To correct the advance angle, the vacuum regulator can rotate the contact group at a small angle relative to the housing.

A capacitor is secured to the bottom of the housing with screws. A drive roller is installed on bushings in the center of the housing. Its bottom has splines with which it engages with the drive gear. In the upper part of the roller there are contact drive cams (for contact ignition) or a steel cup with four slots - a screen (for contactless ignition).

At the very top, on a steel platform, two weights and two springs of the centrifugal ignition regulator are installed. A plastic housing with a moving contact and noise suppression resistance of the high voltage distributor (slider) is screwed onto the top with two screws.

The entire structure is closed with a lid on two spring latches. The body and cover have a tongue and groove so that they fit together in only one position. The cover contains contact terminals for high voltage wires from the spark plugs and from the ignition coil.

Job.

The distributor is connected through the drive to the engine crankshaft and rotates with it. For two full revolutions of the crankshaft, the distributor shaft makes one revolution. This is due to the fact that our engine is four-stroke. When installing the distributor in place, the roller is oriented in strict accordance with the operating order of the engine.

This is done so that the contacts open and the spark jumps on the spark plug when the piston of each cylinder, compressing the combustible mixture, does not reach top dead center (TDC) by a few millimeters. This is called ignition advance. When the number of revolutions increases, the distance must be increased, and when it decreases, it must be decreased, which is what the centrifugal regulator does.

Its weights, under the influence of centrifugal force, which is greater the higher the engine speed, diverge to the sides and move the cams relative to the roller, making ignition “earlier.” When the engine speed decreases, the springs return the weights to their place and the ignition becomes “later”.

This is necessary to increase engine power and efficiency. In addition to the centrifugal one, a vacuum ignition timing regulator is also installed on the distributor. Its function is to fire “earlier” at low throttle opening angles and “later” at sharp throttle opening angles.

Ignition coil device

To test this system, you will need an electrical device such as a multimeter, as well as screwdrivers with different heads and insulated pliers for working under voltage. It is necessary to observe safety precautions when working with the ignition system, because... high voltage electric current flows in the circuit. It is recommended to have rubber gloves or insulated pliers.

The schematic diagram of the VAZ 2106 ignition coil is located here. The figure shows how the ignition coil is connected in the standard version.

The ignition coil, the price of which is acceptable for most Russian motorists, has the nomenclature code 8352.12. and is an oil-filled tank with an open-type magnetic wire.

The standard ignition coil of the “six”, which is easy to buy at any specialized auto parts store, is equipped with 3 contact terminals: “B”, “K” and an output for the central high voltage wire. The ignition coil is connected in the following way: the positive wire of the battery is connected to terminal “B” through the ignition switch contact. Output “K” is connected to the output contacts of both windings of the ignition coils and the negative wire of the battery through the switch.

The high voltage output is connected to another contact of the secondary winding and a high voltage wire contact leading to the breaker distribution element, which, with the rotational movement of the slider, distributes the high voltage current to the spark plugs.

How to install a distributor and configure it on a VAZ 2101 solved 1 answer

The first step is to remove the terminal from the battery, then disconnect the wires from the ignition coil, disconnect the central high-voltage wire, and remove the distributor cover. Next, you need to set the position of the slider so that it is rotated at an angle of 90° with respect to the engine. With this approach, replacing the distributor will have virtually no effect on the ignition timing. You unscrew the spark plug of the first cylinder, plug the spark plug hole with a rag, and begin to manually turn the crankshaft pulley clockwise, if you look at the engine against the movement of the car, until the rag jumps out of the spark plug hole. It is best to turn the engine with a ratchet wrench specially purchased for this purpose (or made independently according to a sample). In order for the position of the new distributor to be the same as the old one, you need to make a mark on the cylinder block as shown in the figure.

Preparation

As previously noted, you can do without such a device as a strobe light, but if you want to set up the ignition yourself, then there is still a reason to purchase it.

Before you start setting the angle, do the following:

• start the engine;
• heat it up to 90 degrees;
• increase the speed to 800;
• remove the pipe used to discharge the fitting;
• the dismantled tube is clamped with a finger - this will allow you to find out whether vacuum is actually occurring;
• if it is present, the speed is increased until it disappears;
• then the engine is turned off and the pipe is bent so that there is no gap left in it;
• use a wrench to unscrew the nuts securing the distributor;
• clean the inspection hole from dirt (it is located in the crater of the gearbox and is closed with a plug).

There is a special scale with which the set angle is determined. This should be discussed in more detail, since you need to set the ignition according to the marks. For this:

• Use a flat screwdriver to turn the flywheel until a long strip appears;
• in the future, during adjustment, you need to ensure that it remains clearly in the triangular cutout (this is the zero angle, that is, the starting point of adjustment).

If everything is done correctly, then cylinders 1 and 4 move to the TDC position.

When the scale is poorly visible and you are not sure that you have found the necessary feature, then you can verify the correctness of the position in another way.

There are pulleys on the camshaft gears. They must coincide with the mark on the wall of the timing belt protective housing.

Electronic ignition system design

1) Sensor-distributor, acting as a contactless distributor. 2) Switch, the functional purpose of which is to interrupt the current of the primary circuit of the ignition coil in accordance with the signals of the sensor-distributor. The circuitry of this device provides a mode for automatically shutting off the current passing through the ignition coil when the power plant is not working (the ignition is on). 3) An ignition coil that converts an intermittent low voltage current (12 Volts) into a high voltage current (10-20 Kilovolts), initiating a “breakdown” » air gap on the spark plug electrodes. 4) A set of wires. 5) A set of spark plugs that ignite the fuel-air mixture through a spark discharge. The use of spark plugs in BSZ that are not designed for a high-power spark discharge is not recommended, since they quickly fail due to overheating.

About the drive mechanism

To transmit torque to the distributor shaft on the “six”, a helical gear is used, rotated by a timing chain (in common parlance – “hog”). Since the element is located horizontally and the distributor roller is vertical, there is an intermediary between them - the so-called fungus with oblique teeth and internal slots. This gear simultaneously turns 2 shafts - the oil pump and the distributor.

The distributor drive consists of two transmission gears with oblique teeth

Both transmission links - the “hog” and the “fungus” - are designed for a long service life and are replaced during engine overhauls. The first part is removed after disassembling the timing chain drive, the second is pulled out through the upper hole in the cylinder block.

The VAZ 2106 distributor, equipped with a contact breaker, is a rather complex unit consisting of many small parts. Hence the unreliability of operation and constant failures of the spark generation system. The non-contact version of the distributor creates problems much less frequently, but in terms of performance characteristics it still falls short of modern ignition modules, which have no moving parts.

Non-contact ignition system device

The schematic diagram of the VAZ contactless ignition of the sixth model is located below.

1. Contactless ignition distributor sensor. 2. Candles. 3. Shielded protection. 4. Non-contact type sensor. 5. Bobbina. 6. Generator element. 7. Ignition switch component. 8. Battery. 9. TC – transistor equipment with a switching circuit (transistor switch).

In such a complex, a non-contact ignition distributor is used to disconnect the low-voltage circuit, which works to open and close the electrical circuit, “locking” or “opening” the output transistor. This system allows you to increase the voltage on the electrodes of the spark plugs and, thereby, increase the energy of the spark discharge. At the same time, the voltage indicator on the spark plug elements does not decrease at low values ​​of rotation of the crankshaft of the power plant, which makes the starting value of the motor much better.

Such non-contact ignition, the price of which is quite high, has significant advantages over the contact system.

Main elements of the ignition system

Now we need to consider the common elements of all ignition systems. They are the same in all, regardless of whether the VAZ-2106 has an electronic ignition system or a contact one. Firstly, candles are everywhere. They consist of a central electrode, with a small gap between it and the ground. It is isolated from the body by a ceramic element. Rare candles live 30 thousand km. mileage, and some even collapse. They burn out so that part of the central electrode falls into the cylinder. For this reason, it is necessary to replace them in a timely manner.

Secondly, armored wires connecting high-voltage parts. They consist of a special fiber through which a high voltage pulse is transmitted. There are five wires in total - four for connecting the distributor cap to the spark plugs. And one is for connecting the coil to the distributor. Thirdly, it is present in all designs, although they have slight differences. Fourthly, the ignition coil is a transformer capable of tens of times increasing the voltage supplied to the primary winding. But the electronic ignition circuit of the VAZ-2106 turns out to be a little more complicated than that used in the classical system.

Settings

The strobe is used like this:

• the red wire is applied to the “plus” on the coil;
• black – to the body;
• the clamp is connected to the veins installed on cylinder number 4.

After this, the actual adjustment begins.

The work is carried out in the following order:

• start the engine, bring its speed up to 800 and no more (measurements are made with a tachometer);
• the beam from the strobe is aimed at the inspection hatch;
• the long line is placed in the zero position (scale in degrees).

The angle is adjusted by rotating to the right - this increases the angle, respectively, movement in the opposite direction decreases it.

It is not difficult to find out the exact direction - it is indicated by the scale marked on the distributor (there is an o and a “plus” there). Each division corresponds to 8 degrees. For this reason, adjustment is slow. After finding the desired position, the distributor is secured.

Main elements of the ignition system

These include:

1. Breaker-distributor. Initially, the first models until the 80s of the twentieth century were equipped with the R-125B device. It was equipped with a mechanical octane corrector, which adjusted the angular value of the ignition timing in a small range, but it was not equipped with a vacuum type regulator. After this, the ignition and fuel supply systems were modernized, as a result of which a distributor with a regulator of the vacuum operating principle and a compatible “Ozone” carburetor appeared.
2. Bobbin B117-A is a contour type, with a disconnecting magnetic circuit, filled with special oil, sealed.
3. Spark plugs A17DV or their export analogues.
4. Ignition switch VK347 with an anti-theft gadget, operating on the following principle: after the ignition key is moved to position III “Parking”, a metal lock pops out of the body part, which falls into a special groove in the steering shaft and does not allow it to rotate.

For emergency repairs of the ignition system of a VAZ 2106 car, it is necessary to have in stock the parts that most often fail. This is a reel and a distributor capacitor; they do not take up much space. Unfortunately, they cannot be repaired.

Adjustment how to set

It is recommended to use a special tool - a strobe light - to adjust contactless ignition. But if it is not there, you can use the following method.

1. We set the distributor slider: unscrew the first spark plug, plug the hole with a finger and turn the crankshaft pulley. If air begins to press on your finger, it means you are on the compression stroke. At this moment, position the distributor so that the slider faces the first cylinder.
2. Seize the moment of ignition. To do this, connect the central wire from the coil to the spark plug and short it to ground. Turn the distributor against the movement of the slider until the spark jumps from the spark plug. This point should be in the area where the slider interacts with the first cylinder.
3. Set the ignition timing completely: with a warm car in second gear, give the gas sharply to the floor. When detonation is heard, set it later, if not, then set it earlier.

Setup video

Contactless ignition uses two important devices - a switch and a Hall sensor. The distributor and sensor must be compatible with each other. The new ignition coil must be an oil-filled type. It is better to take the wires for connecting the system from Niva.

In my free time, I read a lot, play airsoft (a team military sports game) and amateur radio communications. Lots of professional connections. My strengths: communication skills, endurance, responsibility.

Contactless distributor

The device of the distributor, functioning with the electronic ignition mechanism, is similar to the design of a mechanical distributor. This device also has a slider, a plate with a bearing, a vacuum corrector and a centrifugal regulator. However, the contact group and capacitor are replaced by a Hall sensor and a metal screen fixed on the shaft.

The contactless distributor in the 2106th model works as follows:

1. A permanent magnet and Hall sensor are located on the moving section. A screen with slits rotates between them.
2. As soon as the magnet field is blocked by the screen, the voltage is zero at the terminals and the sensor is inactive.
3. When the roller rotates and overcomes the slot, the magnet field reaches the sensor surface. In turn, a voltage is generated at the output of the element, which is sent to the electronic unit (switch). The latter sends a signal to the coil, which generates a discharge going to the ignition slider.

The non-contact dispenser is more durable in operation. The bearing and Hall sensor fail less often due to the lack of mechanical stress.

Signs of incorrect ignition timing setting

These include:

• the vehicle does not reach the maximum speed of the power plant;
• increased fuel consumption;
• the engine idles unevenly;
• the engine unit overheats;
• After the engine stops running, detonation occurs.

Correct installation of the VAZ 2106 engine ignition system consists of 3 stages:

The first stage is a change in the angle of contacts that are in a closed form. The second stage is setting the ignition timing of the VAZ 2106, and the third is adjusting the ignition system while the vehicle is moving. This ignition setting is carried out when the “six” is equipped with a contact ignition system or a transistor switch is installed.

1. Unfasten the latches of the breaker-distributor cover. With a contact system, we first clean its contact group with a needle file and test the degree of their interaction. If necessary, slightly tighten the fixed-type contact.
2. Using a special key for rotating the crankshaft, we select a position of the product when the contact gap becomes extremely large (if it is absent, we put the manual transmission in the 4th gear position and select this moment by moving the vehicle).
3. We unscrew the fasteners that secure the group of contacts on the bearing base.
4. Using a special set of probes, we select a product with a 0.4 mm template and adjust the gap between the contacts so that the template hardly passes between the contacts.
5. Screw in the fasteners and fix the position of the contacts.
6. We carry out verification measurements with 0.35 mm and 0.45 mm probes. In the first case, free movement in the gap of the contact group is allowed, and in the case of the second probe, the passage of the template is not allowed.

General information about the brand

Domestic cars of the 2106 brand were manufactured for the purpose of operating on roads equipped with improved surfaces, regardless of weather conditions. The cars are equipped with a four-door all-metal sedan body.

Cars are equipped with carburetor gasoline engines, four-speed or five-speed gearboxes. There is an independent spring front suspension; The rear suspension is dependent spring. The car's braking system is dual-circuit; there are disc brakes on the front wheels.

The rear ones are equipped with drums. Cars of the VAZ 2106 family were equipped with radial tubeless tires. The steering column has an anti-theft device that is built into the ignition switch.

The modification range of the VAZ 2106 family includes:

• VAZ 2106, 21065-00 - equipped with a model 2106 engine;
• 21061, 21065-01 – equipped with a model 2103 motor;
• 21063 – there was an engine from 21011.
• Car brand 21065 is the luxury version of this family. It has the following differences from the 2106 model: it is equipped with a five-speed gearbox and a final drive with a gear ratio of 3.9. Some cars were equipped with a Solex-type carburetor and a contactless ignition system. The car's electrical equipment is complemented by an electrically heated rear window, halogen headlights and a rear fog lamp. The body has been modified: the upholstery and seat headrests have been updated; The car is supplemented with bumpers of the 2105 model. Spare parts for the presented vehicles are available everywhere. In addition, the electric power steering is a kind of “novelty”, so to speak, the trends of the 21st century are making themselves felt. Thanks to this, car maintenance and repairs are not a big problem.

Checking the coil

In the process of checking the performance of the coil, the first thing to do is check the voltage supply to it.
For this purpose, the voltage supply is turned on and then it is measured between terminal B+ and ground. This value is 12 V. If voltage is not supplied to the coil, then the reason for its absence should be sought in the lock. If normal voltage is present and there is no spark on the spark plugs, it is necessary to measure the resistance of the windings. To do this, the contacts of the measuring device are applied to two side terminals. For the primary winding, the resistance value should be 3-4 ohms.

The resistance of the secondary winding is within 7-9 Ohms. The coil cannot be checked for the presence of a spark by leaning the high-voltage wire against the motor body, since in this case the gap becomes so large that the increased resistance causes breakdown of the winding of the unit, and this leads to failure.

How to check the Hall sensor on Lada 2106: electronic ignition

This controller is the biggest problem on BSZ systems. Its verification will be carried out like this.

1. Elimination method. The failed sensor is replaced with a known good one. To do this, you will need to purchase it or ask your neighbor for a whole sensor. If after installation the engine operation is leveled out, the part is replaced.
2. The second method involves the following steps. To check, remove the terminal from the distributor and turn on the ignition. Next, you need to close contacts 3 and 6. If the sensor is damaged, a small spark will appear.

There are other testing methods that involve the use of a multimeter and other tests. We will not write about them here, since this will require special equipment and deep knowledge of auto electrics.

Malfunctions of the six ignition system

When operating a vehicle, the following malfunctions of the ignition system occur, which must be eliminated before further driving the vehicle.

The table below will help you diagnose and troubleshoot problems that may arise.