Ignition switch relay VAZ 2109 carburetor where is it located

Possible malfunctions and ways to eliminate them

The nature of the lock assembly malfunctions on a VAZ 2109 car can also be electrical or mechanical.

The first group includes violations of the integrity of electrical circuits in the switch at a certain position of the key. If there is no contact, then the connected consumers may not work, or the car will not start at all. If there is contact, but the wrong parts of the circuit are closed, this is fraught with a short circuit and thermal damage to the lock. It will begin to melt and a characteristic smell will appear. Depending on the scale of the disaster, the contact group will most likely need to be replaced.

From a mechanical point of view, the core/larva may become stuck in some position. In this case, it will be physically impossible to turn the key in the lock. The only correct repair option is to replace the entire assembly.

To diagnose faults in electrical circuits, you need to stock up on the following tools.

1. Multimeter or tester. If it is not available, as an option, you can use a control light operating at 12V voltage.
2. A set of screwdrivers and keys for dismantling the lock. Since the only option for repairing mechanical faults is to replace parts that have failed, they will come in handy in this case as well.

Before starting diagnostics, you will have to disconnect the terminal block and ring all contacts in the sequence that corresponds to each of the key positions. For clarity, you should have an electrical diagram of the unit at hand. If the circuit is closed, there will be a resistance indication on the device.

Replacing the lock should begin with de-energizing it. To do this, you will have to loosen the fastening nut and remove the negative terminal of the battery. After this, the protective and decorative casing and the turn/window washer switches are removed. The lock is attached to the steering column using four screws or two screws and a hook latch. It may be difficult to remove due to the screws. In this case, they will have to be cut or drilled, doing everything extremely carefully. The terminal block is disconnected, and the dismantling process can be considered complete.

Assembling a new lock assembly occurs similarly, but in reverse order.

Source



Reasons for premature failure of fuses

1. Moisture getting into electrical contacts. This can cause a short circuit and a voltage surge.
2. Damage to on-board wiring or serviced mechanisms. In such cases, sharp surges and voltage fluctuations occur in the wiring section. As a result, the fuse blows.
3. Setting the fuse element to a too low rating. Some users may mistakenly insert a fuse that is too weak into a loaded circuit. After activating the device, the insert will immediately fail.

How to fix starter malfunctions with your own hands

The electrical component of the starter consists of the following structural elements:

• winding;
• brush assembly;
• solenoid relay.

When checking the solenoid relay, skip the starter operation, bypassing its switching. The relay has 3 terminals at once, one of which is the control terminal. The remaining 2 large terminals, located at the input to the battery and at the output of the starter, are closed using a screwdriver or wrench. Closing for a short period of time is enough, the main thing is that the tool you are using does not touch the metal body directly under the hood.

Remember that starting the engine in this way is prohibited, because the main gear of the device does not engage.

Most likely, the contact planes on the inner plane simply burned out, and therefore a dielectric layer of metal oxides formed on top. To burn the contacts, there is no need to make great efforts; just one start of the VAZ-2109 engine is enough.

There are 2 ways to repair the VAZ-2109 solenoid relay:

1. Dismantle the device and disassemble it into components, clean the contacts.
2. If it is financially possible, it is better to replace the relay completely. Practice shows that if a relay fails, the contacts will have to be cleaned more and more often to restore its operation. If you want the repaired relay to last a long time, give preference to this option for repairing the starter if the device does not spin or click.

Replacing the ignition switch on a VAZ car

To carry out repair work to replace the ignition switch of a vase, we will need: a screwdriver, a tester and a thin awl. Once you have everything you need, you can begin the repair. On all classic VAZ cars, the ignition switch is located at the bottom, on the left of the steering column. To replace you need:

• Disconnect battery
• Remove the plastic casing by first unscrewing the screws that secure it.
• Then unscrew the two screws securing the ignition switch to the bracket.
• We insert the key and set it to position 0 to disable the anti-theft device.
• Insert the awl into the hole in the bracket and press the latch. Then we take out the lock itself.
• After removal, it is recommended to mark the contact wires so that nothing is mixed up the next time you connect.

Removing the ignition switch on a VAZ-2106 begins with disassembling the steering column casing. We unscrew the five bolts and remove its halves. Before you begin disassembling the electrical part of the lock, it is very useful to disconnect the battery by removing the negative terminal or unscrewing the switch bolt. After this, remove the spring retaining ring from the back of the lock body and remove the contact group. We move it to the side so that it does not interfere, and we begin to remove the lock itself.

It is secured in the steering shaft bracket with two bolts, after unscrewing which nothing happens. It is useless to try to remove the lock from its socket if you do not know about the special stopper. It is located on the lock body under the bracket. We press this stopper into the lock with a thin screwdriver through a small hole in the bracket. Further, according to all the instructions, the lock should be pulled out freely, but this does not work.

An obstacle that is not described anywhere is the anti-theft rod. Even though it is in a “disconnected” state, it still clings to the steering shaft. To remove the lock, you have to manipulate the key. In different positions of the lock cylinder, the anti-theft device also moves and is recessed as much as possible when the key is in the “Starter” position. After a few minutes the lock can be pulled out of the bracket.

Here is the time to write that assembly of the unit should be carried out in the reverse order of removal. And in general, this will be true. First you need to insert the new lock into the bracket, recessing the latch and holding the key in the starter position, tighten the fastening bolts, then connect the wires

Particular attention must be paid to this, because an incorrectly connected contact group can damage the starter or ignition system. We reconnect the wires from the old group to the new one one at a time, checking the numbers on the contacts

After this, we assemble the steering column casing.

First of all, you need to get rid of the decorative casing of the steering shaft, unscrew the fastening screws and remove it. We performed similar actions when replacing the steering shaft.

After removing the decorative casing, unscrew the two screws securing the ignition switch to the body, then insert the key into the lock and turn on the “0” position, which turns off the anti-theft device. Through the hole in the bracket, press the lock lock with a thin awl and remove the ignition switch from the mounting socket. This completes the repair work to remove the ignition switch.

To replace the contact group of the ignition switch, you need to use a thin screwdriver or an awl to pry the retaining ring from the edge and remove the contact part. When installing a new contact part, orient it so that terminals “15” and “30” are on the side of the locking rod.

At this point, the repair work is completed, install the new ignition switch in the reverse order of removal, connect the wires, transferring the markings from the old switch to the new one. The pinout or connection diagram of the VAZ ignition switch wires is quite simple and understandable, so every car enthusiast can carry out repairs or replace a spare part without the help of car service employees.

Didn't find the information you are looking for? on our forum.

We recommend reading:

VAZ 2107 heater fan fuse blows

Checking the ignition coil of a VAZ 2112 16 valves with a multimeter

Adjusting the rear axle gearbox of a VAZ 2106 at home

VAZ 2101-2107 bridge diagram, detailed description of parts

Replacing the ignition switch on a VAZ 2114, how to identify a breakdown, repair

VAZ 2112 cylinder head gasket burnt out, symptoms

What kind of oil to pour into the steering gear of a VAZ 2107

Dismantling and assembling the gearbox of a VAZ 2101 car. Video

Where are the fuses VAZ-2108 2109 21099

The relay and fuse block for the VAZ 2108-09-099 (carburetor, injector) is located under the hood, in the compartment in front of the windshield on the left side.

Fuse mounting block 2114-3722010-18

• K1-relay for turning on headlight cleaners;
• K2-relay-breaker for direction indicators and hazard warning lights;
• K3 - windshield wiper relay;
• K4-relay for monitoring the health of lamps;
• K5-power window relay;
• K6 - relay for turning on sound signals;
• K7-relay for turning on the electric heating of the rear window;
• K8-relay for high beam headlights;
• K9-relay for low beam headlights;
• F1-F16 - fuses

Fuse mounting block 2114-3722010-60

• K1 - Relay for turning on headlight cleaners
• K2 - Relay interrupter for direction indicators and hazard warning lights
• K3 - Windshield wiper relay
• K4 - Relay for monitoring the health of brake lamps and side lights
• K5 - Power window relay
• K6 - Horn relay
• K7 - Heated rear window relay
• K8 - Headlight high beam relay
• K9 - Relay for low beam headlights
• F1 - F16 - Fuses
• F1 - F20 - Spare fuses

Fuse mounting block 17.3722

• 1 - relay for turning on headlight cleaners (K6)
• 2 - rear window washer time relay (K1)
• 3 - relay-breaker for direction indicators and hazard warning lights (K2)
• 4 - windshield wiper relay (KZ)
• 5 - contact jumpers in place of the lamp health monitoring relay
• 6 — relay for turning on the heated rear window (K10)
• 7 - spare fuse
• 8 - headlight high beam relay (K5)
• 9 - relay for low beam headlights (K11)
• 10 - fuse
• 11 — relay for switching on the electric motor of the engine cooling fan (K9)
• 12 - horn relay (K8)

Description of the mounting block fuses for VAZ 2109, 2108, 21099

F1-F16 - mounting block 2114-3722010-60, 2114-3722010-18.

Numbers from 1 to 16 - old-style mounting block 17.3722

Power-up modes used

At each of the turns, the connection of certain devices is provided. There are markings in a circle in front of the socket indicating the position to which a certain mode corresponds.

Null

To activate this mode, just insert the key into the “secret”. In this case, devices that are directly connected to the battery remain active.

Additional consumers will be put into operation after the larva is rotated at a certain angle. Voltage is supplied to pins 30/1 and 30.

The first is “ignition”

In the first position, the driver can turn on the front lighting, such as the low and high headlights. The tidy and interior light up responsively. The connection diagram for the VAZ-2109 ignition switch is activated during this turn, releasing current to the 30–INT pair.

When there is a connection between terminals 30/1 and 15/1, the rear lights, reversing lights, turn signals are operational, and the generator excitation winding is energized. The XX solenoid valve also receives power.

In this position, contacts 30/1 and 15/2 are closed, which ensures the operation of, in addition to the head light optics, the functioning of the fog lights, the rear window wiper and its heating. The headlight cleaners, heater fan and engine cooling system propeller are connected to this contact.

The second is the “starter”

By moving the key to the current position, the driver does not block the connection of electrical consumers that were started in the previous “ignition” position. This fully applies to both the closed contacts of the pair 30/1 - 15/1, and to the pair 30 - INT.

The main change that the VAZ-2109 ignition switch connection diagram provides in such a situation is the activation of a pair of contacts 30–50. This allows the starter to start.

Third – “parking”

At this angle of rotation, consumers started in the “ignition” position and closed contacts 30 – INT remain activated. A closed pair 30/1 - P is also added. It is responsible for the parking lighting.

Check and replacement

If the car shows signs of malfunction, there are signs of breakdown of elements of the ignition system, do not rush to immediately blame the starter or module for everything. Often the culprit may be an element that is insignificant in size and cost - the relay.

Dismantling works

To check the relay you need:

• Arm yourself with an ohmmeter or a multimeter more suitable for a motorist, which has all the necessary modes;
• Check resistance indicators;
• We check the holding coil by connecting one terminal of the tester to the relay connection terminal, and the second to ground, that is, the housing;
• Next, the pull-in winding is checked. Here the terminals are connected to the starter motor field winding connection bolt and the control wire connection bolt;
• If there is no resistance, there is only one output - failure.

Checking with a multimeter There is no point in repairing the ignition switch. The element can only be replaced. Plus, it costs pennies.

To replace, you will need to perform a few simple steps. You don't have to be a car repairman here.

1. Disconnect the battery by removing the negative terminal.
2. Using a slotted screwdriver, unscrew the four screws on the steering column housing. This will allow you to easily remove the element.
3. Using a Phillips screwdriver, unscrew another screw that holds the bottom of the casing in place.
4. Remove the steering column protective cover.
5. At the bottom there is a block of the harness with wires where the ignition relay is connected.
6. To replace the relay, you simply need to disconnect the device from the block and install a new element in its place.
7. Check the performance of the car with a new transmission.

As you can see, there is nothing difficult about checking and replacing the device. It does not fail very often, but it is worth monitoring the condition of the ignition relay.

How to find a fault when the main relay does not turn on?

How to find a fault if the engine does not start due to the main relay. First, find a place to install it on the car. It is mainly installed next to the fuel pump relay and the radiator cooling fan relay.

The fuses for the engine management system, fuel pump and radiator cooling fan are also installed there. On VAZ - 2107, VAZ - 2109 cars and its modifications, it is located on a shelf under the glove compartment or under it. On VAZ-2110 and similar cars, under the side of the heater console, on the passenger side. On GAZ cars, they are usually located under the hood on the front wall of the cabin closer to the passenger side.

If, when you turn on the ignition, you do not hear the characteristic click of the relay turning on, you need to use a test lamp connected to the minus to check the presence of power at terminals 85 and 86 of the main relay socket. When using a test lamp, its current consumption should not exceed 0.25A, otherwise damage to the controller may occur. If the control lamp does not light up on any terminal, then the relay is not receiving power. This may be caused by a blown fuse or a broken power cord. In the case when the lamp burns brightly on one terminal, and at half-glow on the second, and the relay may be activated, you should remove the relay from the socket and connect terminals 85 and 86 with a test lamp. When the ignition is turned on, the control lamp should light up. If this is the case, then it is necessary to eliminate the poor contact in the connection of the relay with its block. If the control lamp does not light up, it is necessary to check the integrity of the wire following from the relay to the controller and the contact of the negative wires from the controller to the engine body. On VAZ cars, these wires are attached to the end of the cylinder head above the thermostat, and on GAZ cars to the connecting pin of the receiver and intake manifold in the area of ​​the fourth cylinder. If the wires are OK, but the relay does not turn on, the controller is faulty. For example, on Volga cars, a common malfunction in this case is a break in the negative wire or water getting into the controller, which leads to its malfunction.

If, when you turn on the ignition, there is a click and the relay is activated, then you need to check the power supply at terminals 87 and 30. To do this, touch terminal 87 with the test lamp connected to the minus. If the test lamp does not light up, then possible malfunctions may be a blown fuse or wire break. If there is a plus on pin 87, but when the relay is turned on, there is no positive on pin 30, it means that the relay contacts have burned out and it should be replaced. On VAZ cars, for this you can use a suitable relay from the mounting block, for example a relay for turning on signals, low or high beam headlights, and so on. When searching for a malfunction in which the main relay does not turn on, it is necessary to take into account the presence of anti-theft systems on the car. When installing them, it is not uncommon to include a blocking relay in the relay circuit, which breaks its power supply circuit when the alarm is triggered.

Source

What is

First, let's look at the structure of the castle. Let's find out what it looks like, what it consists of, what its operating principle is, and so on:

As mentioned, the ignition switch is a very important element of the VAZ 2109 car, because almost all available equipment is connected to it.

VAZ 2109 ignition switch malfunction

Scheme

Below is a typical diagram of the ignition switch on the “nine”.

Where is the fuel pump located on the VAZ-21099 injector

Removing and installing a gasoline pump (PG) is not a difficult job and does not require extensive plumbing experience or high qualifications. But if you don’t have to look for a fuel pump on carburetor cars for a long time (it is located on the engine, under the hood), then a beginner may not find it on the injector on the first try. Where is the fuel pump located on the VAZ-21099 sedan injector? Let's figure it out step by step:

• we move the front seats in the car forward as much as possible to free up space in the rear;
• open the rear left door of the car, find a small hinge on the rear sofa, which is located at the junction of the “seats” approximately in the middle of the cabin;
• pull the loop up, thereby raising the back of the lower seat;
• under the carpet we see the gas tank flap;
• unscrew the two fastening screws, remove the hatch and find the fuel pump underneath.

Schemes 2108, 2109, 21099

Scheme of VAZ-2108, 2109 with a low instrument panel (early versions)

There is a “parking light” function - turning on the left or right lights when parking.

Scheme of VAZ-2108, 2109, 21099 with a low panel (later versions)

There is no brake pad wear sensor (previously, the handbrake lamp blinked when the lever was raised, and lit up constantly when the sensors on the brake pads were activated).

Years of production 2108: 1984—2003 in Russia, 2003—2014 in Ukraine

VAZ-2108

Scheme of VAZ-2108, 2109, 21099 with a high luxury panel

Fog lights, central locking, trip computer and electric windows.

Scheme of VAZ-2108, 2109, 21099 with a high panel and Euro fuse block 2114

Fog lights, central locking, heated seats and electric windows.

Scheme of VAZ-21099 with Europanel (production since 1998)

Years of production 2109: 1987-2004 - in Russia, 2004-2011 - in Ukraine

VAZ-2109

Engine control system diagrams

Instrument cluster diagram for low panel

Instrument cluster diagrams for high panel

Connection diagram for headlight cleaners on low and high panels of cars produced after 1989

The headlight cleaners are turned on by a button, in place of the relay there is a jumper.

Years of production 21099: 1990-2004 - in Russia, 2004-2011 - in Ukraine

VAZ-21099

Scheme of a microprocessor ignition system with an MC2713 controller

Scheme of a microprocessor ignition system with an MC4004 controller

Diagram of a mixture control system with a controller under the hood

Diagram of a mixture control system with an under-seat controller

Changes in electrical equipment with rotary motor

Diagram for switching on fog lights since 2000 on a high panel

Since 2000, in accordance with UNECE rule 48-01, the electrical circuit for switching on the rear fog lights has been changed on parts of VAZ vehicles. Added rear fog light relay 2114-3747610, and rear fog light switch 21093-3710030-10 (like a regular one, only without fixing). Instrument panel harness used 21099-3724030

We are reworking the activation of the rear fog lights according to the latest scheme. That is, the button will not be fixed: if the headlights or front fog lights are on, press and release the button for the rear fog lights - they turn on. They turn off when you press the button again or automatically when you turn off the headlights. That is, we will never forget to turn them off. For high panel.

You need rear fog lamp relay 2114-3747610. It may look different, it is also used on the VAZ-2114, 2110, GAZ-3110... It is advisable to find a connector for it, you can just wrap the usual terminals with electrical tape and stick it in.

Remove the jumper from the button

Reworking the connection

Contact 1 of the relay is constant power. You can connect it to the ignition, for example to the yellow-blue heated glass button, then the rear fog lights will sit on the heater fan fuse.

Additional block

It is located in the cabin, under the panel on the right, mainly on cars with injection engine types.

Scheme

Decoding

Relay

We have also prepared a video on this publication on our channel. Watch and subscribe.

Still have questions? Ask them in the comments.

Comments 1

Hello. I have a VAZ 99. Year of manufacture 1998. The car has been converted. I have an injection one. ECU January. Now the question is - is there a difference in the carburetor fuse block from the injection one? I have a block before the 1st sample (finger type), the car sometimes does not start, in general there are a bunch of reasons. A month ago I opened the block, water got in there, I didn’t bother and bought a used one exactly like this and installed it. after replacement even more problems. Should I install another block? Please let me know.

Source

VAZ 2109 generator circuit

If you lose charge, this is most often due to a failure of the generator, and most often it is the generator brushes, but it happens that there are winding breaks and a short circuit in the circuit or an open circuit. In this case, I recommend that you familiarize yourself with this generator circuit for the VAZ 2109.

Download diagram

Numerical designations on the diagram

Fuses and relays Volkswagen Golf 6, 2008 - 2013

The main power supply circuits of the vehicle's electrical equipment are protected by fuses. Headlights, fan motors, fuel pump and other powerful consumers are connected via relays. Fuses and relays are installed in mounting blocks, which are located in the engine compartment and interior of the car. The information is relevant for Volkswagen Golf 6 models 2008, 2009, 2010, 2011, 2012, 2013.

In the cabin

1) To access the fuse mounting block located in the passenger compartment...

2) Pry up the edge of the cover of the mounting block 3) overcoming the resistance of the latches, remove the cover Fuses in the mounting block located inside the car

Relay in the mounting block located in the passenger compartment

Where is the fuel filter located?

The fuel filter (TF) on the VAZ-21099i is designed to clean gasoline from debris, dirt and various impurities; it is a monolithic structure with a rigid metal body and a filter element inside. The frequency of its replacement is every 20-30 thousand km of the distance traveled, also if the car begins to move jerkily, and diagnostics showed that the fuel pump is clogged.

It’s easy to find out where the fuel filter is located; to do this, you need to install the car on an inspection hole or a car lift. The TF is located on the bottom of the body, next to the rear beam and the gas tank, and is secured with a special clamp, which is tightened with a bolt and nut.

Before you start changing the filter, you need to relieve the fuel pressure, otherwise when you unscrew the fuel fittings, gasoline will splash under high pressure. You can relieve pressure in the line using a special nipple located at the rear of the fuel rail. Before starting such an operation, it is necessary to prepare a plastic container into which gasoline should be poured, then unscrew the safety cap.

To release the pressure, you can use a standard flat-head screwdriver; when you press the nipple valve, gasoline will come out of the system.

After removing fuel from the line, we proceed to replacing the fuel pump.

The most common ignition switch problems.

Many owners of "nines" note one unpleasant feature of their iron "horses" - that over time, the ignition switch in them simply begins to jam. Even if it was installed quite recently. Most likely, this defect is a manufacturing defect and you need to contact the store where you purchased the new ignition switch (for this purpose, it is better to save receipts for such purchases) to make a return. However, if this option is not available to you, do not despair!

The fact is that when the ignition switch jams when starting the engine, voltage is supplied to the starter, which can lead to failure of this part. But this does not mean at all that you need to run to the auto store for a new part. In this situation, you can simply buy silicone grease and apply it inside the lock every time the lock jams.

Ignition switch consumers.

This article will be useful to those who want to upgrade the ignition switch (for example, start the engine with a button) or are experiencing problems with the lock. Only the electrical part of the lock is described. We will consider the ignition switch in the VAZ-2114 version. It, unlike the VAZ-2108 lock, works in conjunction with the ignition relay.

The lock has 4 positions, of which only 3 are actually used:

0 - all consumers are turned off (used extremely rarely) 1 - ignition is on 2 - starter is on 3 - parking (the key is removed from the lock) Voltage from the battery is always supplied to contacts 7 (pink) and 8 (brown) of the lock. These wires are connected in parallel and connected in the mounting block. The division into two wires was apparently done for reliability, or it may have developed historically - these wires can be replaced with one wire. The brown wire connects the ignition system (carburetor version), instrument panel and some other consumers. Pink is responsible for the rest of the load.

Testing the serviceability

The lock's service life is limited. After it fails, it is necessary to repair or completely replace the product. The functionality is checked after inserting the key into the “secret”.

Failures occur due to mechanical wear or loss of contact. The check is carried out by turning the key. If it begins to jam, then as a temporary solution it is possible to use silicone grease by dripping it inside.

In order for the wiring diagram to function correctly, you need to know which contacts to connect to each other. Typically the following wiring system is used:

• red connects to the cable from the starter;
• the pink wire goes to “+” from the 12 V battery;
• brown +12 V is used to start the ignition relay;
• white – relay on;
• black and blue connect other consumers.

It is necessary to check the contacts for the presence of carbon deposits or the possibility of oxidation. Burning contacts can be heard in the cabin by the characteristic smell of burnt insulation.

For the VAZ 2109, as well as for all other cars, the ignition switch is one of the most basic elements of electrical equipment. This element consists of a mechanical and electrical part. The mechanical part is responsible for locking the steering wheel when there is no key in the lock, and the electrical part is responsible for supplying voltage to the necessary electrical circuits depending on the selected position.

If you installed it yourself

The previous owner of the car, in the absence of such a standard part, could install it himself. Such installation kits are sold in car dealerships. In this case, the electric relay can be located not only in the “standard” location. Finding it without calling the previous owner will not be so easy.

If a breakdown of this part occurs on the way, then you can start the car by closing contacts 87 and 30 (the location and circuit diagram are printed on the top of the relay housing). In this case, you are allowed to use the machine without any restrictions. But at the first opportunity, be sure to fix the breakdown. The operation of the VAZ-2115 ignition system directly depends on the relay.

Where is the speed sensor located?

The speed sensor (DS) on front-wheel drive VAZ cars reads pulses depending on wheel speed and transmits the data to the electronic control unit (ECU). When braking the engine, the fuel supply is turned off with the help of the diesel engine and the computer, thus achieving more economical operation of the internal combustion engine. If the sensor is faulty, an error code is recorded, gasoline consumption increases slightly, and idle speed decreases, especially during heavy braking. It is difficult to immediately detect where the speed sensor is located, since it is hidden under the air filter housing (AFC).

We find the part we need as follows:

• open the hood of the car;
• Using a 10mm wrench, unscrew the two KVF fastening bolts;
• loosen the clamp of the air “corrugation”, disconnect the “chip” with the wires;
• we take out the KVF, now the sensor has already appeared in the field of view, it is located on the gearbox (gearbox) housing, wires are connected to it, connected using a connector.

The DS can be easily unscrewed by hand, and the plug with wires can be pulled out even after the sensor has been unscrewed (but carefully so as not to damage the wiring during rotation).

Location and electrical diagram

On older models (manufactured before 1998), the relay and fuse mounting block is marked 17.3722. This device consists of a plastic case, which, in turn, has a lower part and a cover, as well as an engineering board. It is to this board that the wire contacts are soldered, and fuses and relays are installed.

As for newer car models, that is, those released after 1998, their power supply units are marked with the numbers 2114-3722010-60. Fuses are installed in them (hereinafter referred to as FCs) and these blocks differ from each other by their electrical circuit and some nuances in the purpose of the elements. It is worth noting that regardless of whether your car is fuel-injected or carburetor-powered, the design and electrical circuit of the power supply will depend on the year of manufacture, and not on the type of fuel supply.

We are reporting this in order to dispel the myth that is circulating among Russian motorists. Drivers seriously believe that the layout and design of the unit depends on the fuel supply system, but we assure you that this is not the case.

The main difference between these two types of power supply is:

• different designations of device parts;
• different fuse ratings;
• In addition, the manufacturer decided that when developing a new power supply, it was necessary to remove the cooling system fan motor relay, as well as the device time relay.

Marking 17.3722

Let's take a look at the electrical circuit of the old-style power supply unit, as well as the purpose of the fuses. As we said at the beginning of the article, a power supply with such a circuit can be found in a VAZ 2109, both equipped with an injection and a carburetor engine.

If you are the owner and your heater fuse or fuel pump fuse has failed, for example, then it would be useful for you to know the purpose of the unit’s parts.

In addition, information about the purpose of the relay will be useful to you. It is presented below.

Why does oil appear in the distributor, what should I do to eliminate it?

• Why does oil appear in the distributor, what should I do to eliminate it?
• Purpose of the distributor and its design
• Why does oil get into the distributor?
• Distributor repair, step-by-step instructions
• Distributor, assembly nuances
• Ignition adjustment, some points

A car engine is a rather complex device, and for its full functioning, the coherence of all parts and mechanisms is necessary. So, for example, one of the important elements of gasoline units is a distributor-distributor or simply a distributor.

Purpose of the distributor and its design

It is no secret that the normal operation of the power plant directly depends on the timely formation of a spark. The distributor is precisely the important element that is responsible for its appearance at the right moment, that is, when the piston has reached TDC. Simply put, without a distributor breaker, most gasoline internal combustion engines will not be able to operate.

If we evaluate the role of the distributor in the ignition operation, it is worth noting that it:

– provokes the appearance of a spark by breaking the breaker contacts (in modern vehicle models a Hall sensor is used for this);

– directs the high voltage generated in the ignition coil to the desired spark plug;

– changes the beginning of the moment of spark formation in accordance with the driving mode and the fuel used (for this, vacuum and centrifugal regulators are installed);

– is responsible for the accumulation and discharge of energy in the reel.

The main components of the device include:

• distributor drive (rotor, which is presented in the form of a splined shaft that engages with the camshaft gear or a special shaft, which depends on the design of the power unit);

• ignition coil with double winding;

• Diagram of the EPHH carburetor system 2108, 21081, 21083 Solex

• breaker – contains a jaw clutch, a group of contacts and a centrifugal clutch;

• distributor – presented in the form of a slider attached to the clutch drive shaft, which rotates with it;

• distributor cover (it is from this that high-voltage wires extend to each of the spark plugs).

In addition, integral components of the distributor device (in particular, on VAZ group cars) are a vacuum ignition timing regulator and a capacitor, which is used to collect a certain part of the charge, which protects the contacts from rapid melting due to exposure to high voltage. Based on the type of distributor, an octane corrector can be installed in its lower part, which is connected to the drive roller, which regulates the rotation speed according to a certain type of gasoline, that is, its octane number. In older versions of the device, this indicator is adjusted manually.

Why does oil get into the distributor?

The most common reasons for oil getting into the distributor of VAZ cars is a clogged hole in the base of the carburetor mechanism (intended for crankcase ventilation) and worn out oil seal. To eliminate these troubles, in the first case it is enough to clean the hole (preferably with the help of service station specialists), and to solve the second problem you will have to replace the problematic oil seal. Every car enthusiast can perform this task independently, but it is still better to turn to specialists.