Autostart Tomahawk 9010 step-by-step instructions for turning on and off the alarm

Author: Victor

The car engine is started by command on the Tomahawk 9010 alarm system by pressing the remote control button with the key icon. In accordance with the Tomahawk 9010 autostart instructions, before enabling the automatic or remote start function, the user must configure the “Program Neutral” mode. It is safer and more accurate to control the operation of the engine using the tachometer; for this you need to program the idle speed.

[Hide]

Engine operating parameters during autostart

List of parameters for the configured automatic launch of the alarm:

1. The operating time of the power unit can be 5, 10, 15 or 20 minutes. By default, the car alarm is set to operate for 10 minutes, but during the cold season it is recommended to increase the warm-up time.
2. Temperature mode for starting the power unit automatically. This parameter is measured by the control unit in the vehicle interior, and not by the engine. The user can adjust the temperature from -5 to -30 degrees. Normally, the power unit should turn on at -10°C.
3. According to the application manual, the user can adjust the cranking time of the starter mechanism of the crankshaft. This parameter is 0.8, 1.2, 1.8 or 3 seconds. Initially, the starter is set to autoload for 0.8 s. If the option of monitoring the engine using tachometer signals is used, the alarm will automatically deactivate the unit, so it is recommended to set the interval to 3 s. If startup failures occur, with each subsequent start attempt, this parameter increases by 0.2 s.
4. The user can set one of the options for monitoring engine operation - by mains voltage, tachometer or engine fluid pressure indicator.
5. If the car owner has to add an engine blocker bypass to the ignition system, then it is necessary to adjust the duration of operation of the second additional channel. The operating time can be 0.8, 10 or 30 seconds. You can make the channel function for the entire time after automatic start. The setting of this parameter depends on the engine blocker of a certain car model.
6. Control of the IGN2 power output on the ignition switch and central locking (CL) during automatic start. You can configure the central locking to lock or unlock after startup.
7. Set start delay between activation of the ignition and starter mechanism. For power units running on gasoline, this parameter should be 2 s, and for diesel engines - from 2 to 10 s.

Video: features of setting autorun parameters

User Ivan Vasilyevich in his video reported on setting up a remote engine start on the Tomahawk alarm system, as well as on the engine operating parameters.

Idle speed programming procedure

If the engine operation is monitored using a tachometer, then in accordance with the Tomahawk 9010 autostart instructions, you need to do the following:

1. The car's ignition system turns on.
2. The “Override” emergency mode activation button is pressed nine times. If the installation of the security system was not carried out independently, then you need to check with the specialist where the key is located. It is recommended to install it discreetly, so most likely the control element is located under the instrument panel. If you have any difficulties with the search, you should check each wire coming from the microprocessor.
3. The ignition is turned off. The siren should emit nine beeps.
4. The user starts the engine with the key.
5. After reducing the idle speed to optimal, the “Override” emergency mode button is pressed once. The control is held until the siren sounds once. If the number of pulses is 4, this indicates that the specified source of the tachometer signal is not recognized correctly by the control unit. Accordingly, the alarm system will not be able to use it. It is recommended to check the operation of the idle speed sensor and its wires; if there is a malfunction, the device is replaced.

We set the heating time: every 1, 2, 4, 24 hours

The hourly start of the engine on an automatic transmission or on a car with a manual transmission is set according to the same algorithm (indication 2-1 DAILY).

1. Hold down the Lock/Key button. A remote control signal will follow.
2. Then press the “zZ” key. The system LED will light up twice.

To set the interval.

1. Enter the programming menu (described earlier).
2. Click "Override" seven times.
3. Press the “Machine closed” button – 1 hour.
4. “The castle is open” - 2 hours.
5. Trunk release button - 4 hours.
6. “Crossed out speaker” – 24 hours.

A combination of buttons will help you change the engine warm-up time.

1. Enter the programming menu (described above).
2. Press "Override" six times.
3. Click the “Lock closed / zZ” button - 5 minutes.
4. "The Key" - 10 min.
5. "Trunk" button - 15.
6. “Crossed out mouthpiece” - 20 min.

How to enable autorun?

The engine cannot be started if:

• ignition on;
• the hood is open;
• the car is not on the handbrake;
• service mode is enabled;
• The pre-launch procedure has not been completed (for manual transmission).

Performing "Software Neutral"

Setting the “Program Neutral” mode:

1. On a car with the engine running, the handbrake is raised.
2. On the pager, a key with a symbol in the form of a key is “clicked”. After the “click”, an indicator in the form of smoke from the exhaust pipe will appear on the remote control display. The pager should also emit a melodic signal.
3. Within the next 30 seconds, the user must remove the key from the ignition and leave the car. The engine will remain running. After closing the last door, the alarm will turn off the power unit and activate the machine protection mode.

Table: starting the engine from the key fob

Table: Remote extension and engine stop

Table: how to set the trigger by temperature

When the temperature drops to the set threshold, the motor will start.

Table: daily run settings

Table: automatic restart at certain intervals

If you want to start the engine after a certain time interval, then within five seconds after turning on the daily start function, press the buttons:

Video: setting up engine autostart

User Olzhas Zhailaubay in his video spoke in detail about programming the automatic engine start option.

Preparation for automatic and manual

Before using the Tomahawk TV 9030 autostart function, prevent the vehicle from moving. On a vehicle with an automatic transmission, move the lever to the park position. On a car with a manual transmission, set neutral manually and apply the parking brake. Follow the steps before turning off the engine.

1. Hold down the “Lock open” key until the remote control beeps.
2. Press “Key” again and do not release for a second.
3. Turn off the ignition and the engine should be running.
4. Get out of the car and close the door. The control unit will automatically turn off the engine and arm the car.

The security mode with door locking during auto start is set as follows.

1. Press "Override" eight times.
2. Clicking the “Lock closed” key turns off the function.
3. Turn on the mode by pressing one of the buttons: “Car is open”, “Trunk”, “Speaker crossed out”.

Parking lights during auto start are turned on according to the following algorithm.

1. Press the Override button nine times.
2. The first option is the “zZ” key.
3. The second method is “Key”.
4. The function is disabled – one of the buttons: “Trunk opener”, “Speaker crossed out”.

Set the door closing mode at the end of autostart.

1. Click the “Override” key ten times.
2. "zZ" turns off the function.
3. Turn on the mode by pressing one of the buttons: “Car is open”, “Trunk”, “Speaker crossed out”.

Table: how to disable autorun?

Setting a specific temperature

Now it’s worth talking about how to set a certain temperature level necessary to automatically start a car engine. In order to set the engine to operate automatically at a temperature of -5°C, you should press and hold the button on which the icon in the form of a lock will appear and the system will emit 1 CHIRP. If you want to set the temperature to start the engine -10°C, you should hold down the key button, and the system will issue 2 “CHIRPS”.

To set the start at -20°C

, you need to hold the button with the trunk icon and the system will emit 3 “CHIRPS”, and to start at -30°C you should hold the mute button until the system emits 4 “CHIRPS”.

Problems with autostart

Possible reasons that may affect autorun operation:

1. The limit switch mounted on the hood shorts to ground. It is necessary to check the integrity of the device and replace it if necessary. If the trigger fails, its rod may “stick” in the lowered position. You will also need to check the wires and make sure their integrity; if the electrical circuits are damaged, they are replaced. The reason may be oxidation of the contact on the sensor; to eliminate the problem, the conductors are cleaned.
2. There is no output in the conductors connected to the ignition switch. It is necessary to reconnect the cables in accordance with the installation and connection diagram.
3. A “conflict” has arisen in the operation of the standard engine immobilizer and alarm immobilizer. If your car uses a keyless security system, you can leave the key in the car to troubleshoot the problem. However, this is the least safe option and may result in the vehicle being stolen. In order to eliminate the malfunction, it is necessary to install an immobilizer bypass.
4. There is no power supplied to the ignition switch; one of the fuses has failed. Each element is subject to diagnosis and replacement in case of breakdown or burnout. Only fuses of the correct rating must be used.
5. The ignition switch or starter mechanism is faulty. With such a problem, diagnostics of all electrical circuit contacts connected to these devices is required. The contact pad with the cylinder in the ignition switch may have worn out; this element must be replaced.
6. Failure of the temperature controller responsible for starting the motor. The contacts on the sensor could have oxidized, causing it to not work. A detailed check of the conductors with replacement of damaged electrical circuits is required. It is recommended to additionally wrap the cables with electrical tape to prevent rapid wear and damage. A failed sensor cannot be repaired and will have to be replaced.
7. Incorrect installation of the anti-theft system. Errors made during installation and connection will lead to current leakage, which will ultimately cause the battery to discharge. The device will need to be charged to resolve the problem. You need to make sure that the wires from the alarm are not frayed or worn out.
8. Faulty mounting block with fuses. The elements themselves may be in working condition, but as a result of exposure to high loads, the contact path could burn out. To eliminate the malfunction, you will need to disassemble the module and replace the working platforms.
9. Failure or incorrect operation of the microprocessor module. It is almost impossible to calculate software malfunctions without special equipment and knowledge. To determine the cause, you need to contact a specialist. The control unit may not operate as a result of oxidation or clogged contacts on the main connector. To fix the problem, you will need to clean the pad.

Connection instructions

Installation of Tomahawk 9030 with autostart is carried out in strict accordance with the instructions. First disconnect the battery by removing the negative cable. Installation locations must meet the following requirements:

• secrecy and inaccessibility for attackers;
• away from sources of heat, moisture and dampness;
• at a distance from the standard electrical equipment of the vehicle.

When installing an alarm, observe the following rules:

• Place the control unit only inside the passenger compartment: under the instrument panel, next to the wiring. Protect the unit from vibrations;
• Install the antenna as high as possible. It should not touch metal parts;
• Place the siren in the engine compartment. Point the horn down to prevent water from getting inside;
• connect the wires inside the car, soldering them together;
• protect the alarm control unit from power surges in the network with fuses;
• Install the shock sensor in the center of the cabin.

Video: malfunctions in Tomahawk autostart

The Samodelkin channel in its video talked about problems that can occur when implementing automatic start on the Tomahawk 9010 alarm system.

Do you have any questions? Specialists and readers of the AUTODVIG website will help you ask a question

Was this article helpful?

Thank you for your opinion!

The article was useful. Please share the information with your friends.

Yes (83.33%)

No (16.67%)

X

Please write what is wrong and leave recommendations on the article

Cancel reply

Rate this article: ( 6 votes, average: 4.83 out of 5)

Discuss the article:

Setting the start timer

Now you need to figure out how to set a specific time at which the car will work. To do this, you need to hold down several buttons at the same time:

• timer for 10 minutes – hold the mute button and press “F”;
• timer for 20 minutes - hold the mute button and press “F” twice;
• work for 30 minutes - hold down the button with the sound deactivated and press “F” three times;
• work for 1 hour – hold down the sound deactivation button and press “F” four times;
• similarly, to set the timer for 1.5 and 2 hours - hold the mute button and press “F” 5 and 6 times, respectively.

As a rule, when installing an alarm system in the cabin, professionals will do everything for you and you should not worry about the fact that you will need to install any functions yourself. If you don’t understand how to set the heating on the Tomahawk, then ask a specialist at the salon about it. Usually, when installing a “reliable guard” for your iron horse, you are given special instructions that contain commands for connecting a particular function.

Programming remote start from key fob

Below we will look at how to turn on the engine of your car using the Tomahawk TW 9030 remote control. You can use both the main and additional transmitters.

1. To remotely start the engine, press and hold the “Key” key. A sound signal from the main remote control will follow or the color of the LED on the additional pager will change.
2. Press the “Lock Open” button again. Do it in three seconds.
3. The car engine will start running.
4. Turn off the engine by pressing the same key.

How to set temperature trigger on Tomahawk 9030 alarm system

The operating instructions will help you set the start of the car's power unit based on temperature (indication 1-2 TEMP START). Enter the automatic engine start programming menu (this is described in detail above). Set the temperature. Enable the function by following the steps below.

1. Simultaneously press and hold the “Trunk Opening” and “Key” buttons.
2. The lights will blink once and the siren will sound once.
3. A snowflake will appear on the key fob screen.

Many car enthusiasts are wondering how to see the temperature at which the engine will autostart. This information is located on the alarm key fob screen.

The second question is where is the temperature-controlled engine start relay located? It is located in the alarm control unit. Temperature sensors are located inside the car.