The Tomahawk 9010 warm-up instructions contain comprehensive information about the functions and the procedure for their activation and calibration. The option is in demand among users of northern regions, where starting a car after a long period of inactivity in the cold is problematic. The user manual helps you set up autorun.
Here are the options explained:
- hourly warm-up;
- temperature trigger;
- activation of the ignition from the remote control;
- daily car factory.
A complete set of add-ons is controlled from a spare or main key fob and allows you to comfortably use all the technologies integrated into the head alarm module.
Also on the pages of the brochure there is information about possible system breakdowns and methods for eliminating them.
Find out everything about the Tomahawk TZ-9010.
Setting up and preparing for autorun
To properly arm the vehicle in automatic engine start mode, the plant has provided a certain sequence of actions. Moreover, for each type of machine, the procedure is different, which raises the question of how to set it on a manual or automatic machine for 100% operation of the mechanism.
Factory calibrations are already programmed into the device’s processor. This shows the required heating of the air inside the cabin (start by temperature), the frequency of activation when starting the engine by time (1 hour at stock). Settings can be changed in the programming menu.
Physical training is performed as follows:
- set the gear lever to neutral position;
- raise the handbrake all the way;
- remove the key from the ignition;
- quickly leave the car.
After this, you will need to dial a standard combination from the remote control.
Autorun function
To enable the autorun function, you need to know which buttons to press. Depending on the model, the buttons and functions may differ, however, in most cases they are the same. For example, the Tomahawk Q9 Dialog or TZ-9031 requires you to press a key that has a key on it. After this, the headlights should turn on and off three times and the siren will signal three times that the function has been completed. The display should then show several icons:
- “St” - an attempt was made to start the engine;
- “SP” - the engine failed to start;
- “Car” - the engine is running, the key fob emits the corresponding melody.
In this case, the motor will operate in accordance with the set period of time. You can program the engine operating time yourself; to do this, you need to study the table attached to the alarm with the relevant information. Then the motor will automatically turn off until the next start. You can also increase the engine warm-up time by pressing the “lock” and “key” buttons simultaneously. Each such press adds exactly 5 minutes, the maximum increase in time is 20 minutes. The TZ-9011 or SL-950 display will show the time remaining before the engine turns off.
Starting the engine of models 9.3, as well as 9.5 and others cannot be carried out only if the following requirements are met:
- The gearshift lever is not installed in the neutral position;
- the car hood is open;
- the ignition is already on;
- The car is not on the handbrake.
In these cases, when you try to autostart an alarm model, for example, TZ-9030 or 9.9, four beeps will sound. Additionally, in some models you can set the starter cranking time.
Autostart Tomahawk 9010: button combination, remote engine start from key fob
Most regions of Russia experience severe frosts in winter. In such conditions, after a long period of inactivity, starting the engine is problematic. The automatic start option allows the driver to leave the car in the parking lot and not worry about the need to warm up in the morning. By adjusting the modes, you can achieve the desired starting frequency and heating time of the power plant.
Typically, the module is configured from the assembly line to turn on hourly and operate for 5 minutes. In practice, the conditions are relevant if the temperature in the box or in the parking lot is less than -25 degrees Celsius. In more comfortable conditions, frequent frequency is not needed and the user is given the opportunity to determine the interval and time independently.
The factory instructions indicate how to enable autostart from the key fob when using an automatic transmission or manual transmission.
Emergency activation and deactivation of the alarm system
If the car does not respond to the key fob, you can use the emergency activation and alarm disabling function.
Emergency alarm activation
To activate an emergency alarm, you must:
- turn on the ignition, but do not start the engine;
- press the Override button eight times;
- turn off the ignition.
The car will react with a single flash of the parking lights and a single sound of the siren. After 20 seconds, the system will automatically turn on the security mode.
If, 20 seconds after the emergency activation of the alarm, any of the security zones are triggered, the car will notify the user of this by flashing the parking lights four times and sounding the siren four times. After this, the user will have 20 seconds to disarm it. If this is not done, the system will activate the alarm mode.
Emergency alarm shutdown
To make an emergency shutdown of the alarm without a key fob, you must:
- turn on the ignition (do not start the engine);
- press the Override button four times;
- turn off the ignition.
The parking lights will flash twice and the siren will sound twice.
REFERENCE. The key fob pager will continue to function even after the user has made an emergency activation or emergency shutdown of the alarm system
Responsible drivers independently determine how to provide their car with protection against theft, as well as eliminate problems with starting the engine during cold periods. Some of them install a Tomahawk alarm system with auto start on their car. It allows you to start and warm up the engine without leaving the building. But in order to avoid problems with the operation of a car alarm with an auto-warming function, it is important to fully understand how to use it.
Remote engine shutdown with Tomahawk TW 9010
If the car starts automatically according to the preliminary settings. The user has the ability to disable the option from the remote control. This is usually necessary for unscheduled trips or when the motorist simply forgot to deactivate the extension in the spring.
The factory instructions for remotely disarming a car imply a simple sequence of actions.
- Press the lock/key button on the key fob for 2-3 seconds.
- The car will blink its side lights 4 times.
- The keychain will make a specific trill.
If everything is done correctly, the car engine will stall and will not be reactivated.
Auto engine start
By temperature
When installing the Tomahawk 9010 alarm system, an additional temperature sensor is hung under the hood. When autostarting the engine based on temperature, the system is guided by the readings of this sensor, and if an external sensor is not installed, then by the air temperature in the cabin.
To activate automatic engine start based on temperature, you must:
- simultaneously press buttons No. 4 (key) and No. 1 (trunk) - the parking lights will flash once, the siren will emit one beep;
- the melodic trill of the key fob will sound and two new objects will appear on its display: an icon depicting a fan and a warm-up temperature set by software;
- if the system is based on an external temperature sensor, the engine will start when the temperature drops below the programmed mark;
- If the system is based on the air temperature in the cabin, the engine will automatically start when the air warms up to the set temperature.
To disable this function, press buttons No. 4 (key) and No. 1 (trunk). The car will react with a double flash of parking lights and a double siren signal. The key fob will play a melodic trill again and the fan icon will disappear from its display.
By time
To activate timed engine autostart, you must hold down buttons No. 4 (key) and No. 2 (silent security) - the car will honk, the pager will emit a melodic trill and an icon with a clock will appear on its display. From now on, the Tomahawk 9010 will start the vehicle engine every day at the same time when this function was activated.
To disable the daily autostart function by time, you must again press the buttons “4” (key) and “2” (silent security). The parking lights will flash twice and the system will confirm deactivation of the function with two beeps. The clock icon will disappear on the key fob display and a melodic trill will sound.
At regular intervals
The Tomahawk 9010 system allows you to automatically start the engine at regular intervals. To activate this function, you need to activate the daily autostart function, and then within 5 seconds select the corresponding button on the key fob and press it:
- No. 5 (lock) – engine starts every hour;
- No. 4 (key) – start the engine at intervals of 2 hours;
- No. 1 (trunk) – starting the engine at intervals of 4 hours;
- No. 2 (silent security) – starting the engine at intervals of 12 hours.
The system will remember the selected interval. The engine will be started for the first time immediately after the programming session is completed.
How to set the watch on a key fob
The Tomahawk TW 9010 main remote control (with LCD display) has the ability to set the time. An important option is required in order to correctly program the key fob to start by time. If the clock is not set correctly, the car may start during the day or when it is not required.
To set the time on the pager, there is a section of the factory instructions.
- After turning on the screen backlight, press the “F” key.
- After 3-4 seconds the clock display will start blinking.
- To scroll forward, you need to press the button with a picture of an open cargo compartment. Reducing values is done by holding down the key with the speaker.
- You can switch to minutes by pressing “F” again.
To exit the menu, you need to leave the key fob alone for 10 seconds. After idle time, the device will automatically switch to the main screen.
Find out where the Override button is on your Tomahawk 9010 alarm system.
Keychain
The service manual presents all the nuances regarding setting up the communicator. Before carrying out the task, you must make sure that the key fob has working batteries installed.
Button meaning
Designation of indicators on the communicator
Description of the keys:
- The button to activate and deactivate the protection mode is made in the form of a closed lock.
- To automatically start the internal combustion engine and control this option, use a key with a key icon.
- To control the trunk door lock, use a button with a trunk open indicator.
- The key with the loudspeaker icon is used to activate or deactivate the silent protection mode.
- Button for setting parameters and activating the backlight with the F icon.
To configure various commands, you may need to press the communicator buttons for a long time or with a short click. Keyboard shortcuts are also used for this purpose. All this information is specified in detail in the Tomahawk TW 9010 operating instructions. The alarm is configured using the main remote control, but an additional one can be used for control.
Setting up the key fob
Before performing the setup, you must bind the communicator to the microprocessor unit. Without this, adjusting parameters and controlling the anti-theft system will be impossible.
How to write a key fob into the memory of Tomahawk TW 9010?
When performing this task, all information about old communicators will be deleted from the microprocessor memory:
- The key is installed in the ignition switch in On mode. There is no need to start the engine.
- The Override service button is pressed until the siren plays four beeps.
- The key is then released.
- At the same time, on the communicator you need to click on the buttons for opening the luggage compartment and silent security. These buttons are pressed until a signal appears. If the main communicator is registered, the siren will sound once, the additional one - twice, the third - four times, etc.
- Then you need to wait six seconds for the alarm to exit the binding mode. During this time, you cannot click on the key fob buttons or touch the key in the lock.
User Danil Andreev spoke about independently linking a new key fob to the Tomahawk 9010 alarm control unit.
How to configure features?
To adjust option parameters, you must use keyboard shortcuts:
- Simultaneously clicking on the first and fifth buttons will activate the energy-saving function.
- The fifth key is designed to activate and deactivate the backlight.
- Clicking on the second and fifth buttons will allow you to change the notification mode for the car owner. In case of any events, the driver will be warned via vibration or sound signals.
- If you hold down the key number 5, this will allow you to activate the clock, timer or alarm setting.
- Pressing the fourth and fifth buttons, depending on the number, will activate the timer for a period of 10 to 120 minutes.
Setting with Override button
Some functions can be adjusted using the Override key:
- The key is inserted into the lock and the ignition is activated.
- The key is clicked six times. This will allow the car owner to enter the parameter programming mode.
- Then the ignition is turned off. If the function is selected, the LED light will blink and the siren will play a sound signal six times.
- Using the key, the option is changed by successive clicks.
- To assign a specific parameter, all the communicator keys are used except the fifth. Each time you click the button, the siren will play a sound.
How to reset?
To reset all parameters to factory defaults, perform the following steps:
- The car owner enters the programming mode in accordance with the described scheme. To do this, press the key 10 times.
- The ignition is turned off. When the siren beeps, the button is clicked once.
- Then the first key of the communicator is pressed.
- The ignition is activated and switched off. If the settings are reset successfully, the alarm light will sound five times.
The Sher Tiger channel talked about resetting the settings of the Tomahawk anti-theft system on your own.
How to warm up Tomahawk 9010 using time, timer
A separate option for setting the warm-up by the clock allows you to set the required interval at which the engine will start on its own. The option is critically needed in cold climates. If the car is parked for a long time, the power plant can cool down greatly, which makes it impossible to promptly leave the parking spot. Some users cannot start for 2-3 hours after spending the night.
Warming up by the hour can be adjusted. The computer contains thresholds for every 1, 2, 4, 12 hours. In this case, the car will perform the procedure daily until the driver forcibly disables the mode. In parallel, on the on-board network, the timer will be updated each time.
You can read about how to set up a timed start in the factory manual. The necessary sequence of actions and the required preparatory work are indicated here.
Page 12
15. Warming up the engine at a given temperature
After activating this function, starting from the next day, the system will
automatically start the engine daily at the time when it was
this function is activated.
To activate it, you must simultaneously press and hold the buttons
And . The siren will emit 1 “CHIRP”, confirming the activation of the function, automatically
the engine will start. An icon will appear on the display of the key fob pager and a melody will sound.
To disable the daily autorun function, you must press
buttons and . The parking lights will flash 2 times and the system will emit 2 “CHIRPS”
confirming that the function is disabled. will disappear on the key fob pager display
icon, a melody will sound.
16. Daily (1, 2, 4, 12-hour) autostart
The Tomahawk LR-950LE system provides additional temperature-
A special sensor for installation under the hood of a vehicle (see page 32). If this sensor is installed,
starting and warming up of the vehicle is carried out according to the readings of this sensor, otherwise, according to the readings of the temperature sensor inside the cabin.
In order to activate this function, you must simultaneously
press and hold the and buttons. The parking lights will flash 1 time and the siren will emit 1 “CHIRP” to confirm the function has been activated. On the display of the key fob pager
the icon and the set temperature to turn on the heating will be displayed
(programmable, see programming table), accompanied by
melody. When the temperature reaches the temperature set to enable automatic warm-up, the engine will start for the previously programmed time (see.
To disable this function, press the and buttons.
The parking lights will flash 2 times and the system will emit 2 “CHIRPS” to confirm
disabling the function. The icon will disappear on the key fob pager display,
Note.
Automatic engine warming up at a given temperature is performed
no more than 6 times in 2 hours. Temperature for automatic engine warm-up
can be set to -5 C, -10 C, -20 C, -30 C (see programming table). Regardless of the set temperature, when attempting to automatically start, the siren will emit 4 “CHIRPS”.
Tomahawk 9010: instructions for autostart by temperature
The next option has a similar principle. The only difference is the method of activating the program. The computer in mode focuses on the degrees inside the car. Motorists rarely use the extension due to the mode’s irrelevance. The engine warms up much faster than the cabin, which leads to increased fuel consumption.
Thanks to the module software, you can configure the ignition activation threshold and the number of degrees.
How to set the warm-up according to the engine temperature is indicated in the factory instructions. Here you will find all the necessary information about the procedure.
Tomahawk TW-9010: additional temperature sensor
Initially, the Tomahawk 9010 system activates autostart based on interior temperature, and does not provide for installation on the power plant.
Some buyers move the module under the hood, which is quite effective if the sensor is correctly calibrated. The best location for the unit is the cooling system pipe. The element most accurately reflects the state of the internal combustion engine.
You can also perform the transfer yourself using another procedure:
- cut the cable in the antenna module (usually with a blue stripe);
- put a line from the new sensor into the gap;
- lay the line into the engine compartment;
- attach the sensor to the engine or cooling system elements.
Also, some users connect the sensor to the hood lock sensor limit switch. Both options are equally effective.
Find out how to reset settings on the Tomahawk 9010 alarm system.
Auto engine start
By temperature
When installing the Tomahawk 9010 alarm system, an additional temperature sensor is hung under the hood. When autostarting the engine based on temperature, the system is guided by the readings of this sensor, and if an external sensor is not installed, then by the air temperature in the cabin.
To activate automatic engine start based on temperature, you must:
- simultaneously press buttons No. 4 (key) and No. 1 (trunk) - the parking lights will flash once, the siren will emit one beep;
- the melodic trill of the key fob will sound and two new objects will appear on its display: an icon depicting a fan and a warm-up temperature set by software;
- if the system is based on an external temperature sensor, the engine will start when the temperature drops below the programmed mark;
- If the system is based on the air temperature in the cabin, the engine will automatically start when the air warms up to the set temperature.
To disable this function, press buttons No. 4 (key) and No. 1 (trunk). The car will react with a double flash of parking lights and a double siren signal. The key fob will play a melodic trill again and the fan icon will disappear from its display.
By time
To activate timed engine autostart, you must hold down buttons No. 4 (key) and No. 2 (silent security) - the car will honk, the pager will emit a melodic trill and an icon with a clock will appear on its display. From now on, the Tomahawk 9010 will start the vehicle engine every day at the same time when this function was activated.
To disable the daily autostart function by time, you must again press the buttons “4” (key) and “2” (silent security). The parking lights will flash twice and the system will confirm deactivation of the function with two beeps. The clock icon will disappear on the key fob display and a melodic trill will sound.
At regular intervals
The Tomahawk 9010 system allows you to automatically start the engine at regular intervals. To activate this function, you need to activate the daily autostart function, and then within 5 seconds select the corresponding button on the key fob and press it:
- No. 5 (lock) – engine starts every hour;
- No. 4 (key) – start the engine at intervals of 2 hours;
- No. 1 (trunk) – starting the engine at intervals of 4 hours;
- No. 2 (silent security) – starting the engine at intervals of 12 hours.
The system will remember the selected interval. The engine will be started for the first time immediately after the programming session is completed.
How much does a temperature sensor cost?
During operation of the alarm system, damage or failure of the antenna module may occur. The price of a standard sensor is determined by this block. Due to the fact that the sensor is located inside the block and is a single unit with the body panels.
The approximate spread of price tags in different cities of Russia differs. This is due to local characteristics and the complexity of delivery.
Where? | Price, r |
Moscow | 950 |
Saint Petersburg | 1050 |
Rostov | 950 |
Samara | 920 |
Yaroslavl | 900 |
Ekaterinburg | 830 |
Chelyabinsk | 980 |
The cost of the additional Tomahawk TV 9010 sensor is difficult to present in one table. The final price depends on the design and type of part.
How to check the temperature in the cabin?
You can find out the state of the air inside the car without additional modifications or manipulations. The antenna module transmits basic information about the system, and can be activated by holding down the key with the open trunk lid icon. If everything is done correctly, the car will blink its side lights three times and the key fob display will reflect the current state of the system.
To obtain correct information about the temperature of the internal space of the machine, the factory recommends installing the transmitter in places inaccessible to direct sunlight or hot air flows from the climate control system/heater.
How to view the engine temperature on the Tomahawk 9010 key fob: auto warm-up
Checking the engine temperature on the standard system is impossible due to the lack of a measuring sensor. When trying to see information, the user can only see data about the interior on the screen.
However, such a procedure is possible. This will require preliminary preparation and modification of the standard system.
- Break the cable of wires to the on-board antenna.
- Connect the contact from the new sensor to the blue cable.
- Route the line to the motor.
- Install the sensor on the cylinder head or cooling system pipe. Be careful when doing this - the sensitive interior can be easily damaged.
- Press the key on the key fob with a picture of an open hood. The screen will display the current engine temperature.
Also, some users add a secondary element to the engine compartment lid lock limit switch. This method is rarely practiced, due to the increased likelihood of a false alarm.
Important! When installing a motor sensor, it is impossible to see the temperature inside the cabin - the system is not designed to work with two units at the same time.
Installation on the engine
Making a sensor for an alarm with your own hands is still half the battle. You need to install it correctly and connect it to the system. In order for the thermistor to show the engine temperature as accurately as possible, the best place for it is the cylinder block.
The latter cools down later than all other parts, so the signal to turn on the starter will arrive in a timely manner. With a different arrangement, the system mistakenly believes that the engine has already cooled down and will start it more often, which leads to excessive fuel consumption.
The easiest way to mount your sensor is on the thermostat or radiator pipe. In the first case, it will show a more realistic temperature, in the second, it will be easier to connect in parallel with the hood closing sensor. The fastening method is the same:
- attach the homemade thermistor to the metal surface of the pipe;
- secure it with electrical tape;
- insulate the outside with heat-insulating material and fix it with the same electrical tape.
The proprietary sensor should be installed on any metal part of the engine (cylinder block, cylinder head, valve box cover) where there is a protruding pin with an M6 thread. If there are none, you can make a transition piece and secure it into the blind threaded hole of the eye bolt.
How to set a timer on Tomahawk TW 9010
The turbo timer in the security system is an important element for turbocharged cars. The design features of the block do not allow it to be stopped instantly after heavy loads. Heated bearings and mechanisms can be damaged, which will lead to the need for unscheduled repairs.
Setting a timer is useful to be able to automatically turn off the engine after the turbine has cooled down. In this case, you can set the delay to 1, 3 or 6 minutes.
The option is turned on by pressing the Override service key 16 times. To activate the key fob mode, a standard sequence of actions is performed.
- Place the gear lever in neutral position.
- Raise the handbrake all the way.
- Turn off the ignition and quickly get out of the car. In this case, the motor should continue to work.
- Press the arming key (closed lock).
If everything is done correctly, the car will automatically turn off the power unit after the programmed timer ends.
For cars with atmospheric settings, you do not need to activate the add-on.
Autorun function.
First, start the autostart function only when the engine is turned off and the car is set to alarm.
Secondly, observe the conditions for cars with different transmissions. A car with an automatic transmission must be in the “Parking” position.
For mechanics, it is important to leave the gear lever in neutral and activate the handbrake
Tomahawk security systems allow you to use the autorun mode in different ways.
Types of automatic engine start:
- Remote engine start;
- By time (at regular intervals or at a certain time);
- At a given temperature.
Let's consider each type of autorun separately.
Remote engine start
The easiest way to use the engine auto-start option is to force this function to be turned on. That is, the owner turns on the automatic engine start mode remotely, and the car runs for a certain time. The driver then drives off with the vehicle ready to go. To remotely start the engine, you need to perform a simple algorithm of actions:
- Press the “KEY” button on the key fob
- The parking lights will flash three times and the siren will sound three times;
- The signal for successful activation of the function is the appearance of the “CAR” sign on the mini-display. In this mode, the key fob emits a melody
The engine will run for the pre-programmed time.
By time
Under constant weather conditions, when the autostart has to be used daily, the car owner can configure the automatic operation function according to the specified time interval parameters. To activate this option, you must follow the following algorithm of actions:
- Press and hold the “KEY” and “LIGHT OFF” keys together until the parking lights turn on and then turn off.
- The text “CLOCK” will appear on the display of the car alarm key fob, set the time you need
- A short ringtone will sound as a sign of successful activation of the function
Trigger by temperature
During the cold season, when the temperature at night drops to below 20
Instructions for connecting the “Autostart by temperature” function:
- Press and simultaneously hold the “TRUNK OPEN” and “KEY” buttons until the side lights turn on and a sound signal appears
- The “SNOWFLAKE” icon will appear on the mini-display. Set the air temperature at which you want your car to start automatically.
- The signal for successful activation is a short musical ringtone.
The option allows you to configure autostart at temperatures from -5C to -30C no more than six times in an interval of 2 hours.
How to extend or reduce warm-up time on Tomahawk 9010
When using the Tomahawk 9010 security system, the question periodically arises of how to add or change the warm-up time. This is often due to the incompatibility of the factory settings with the actual operating conditions of the vehicle.
The proprietary software supports the ability to increase or decrease parameters. This is done through the service mode.
- Press the Overide key. The system will produce one short chirp.
- Setting a 5-minute delay is done by pressing the closed lock on the key fob.
- For 10 min. you need to press the key on the remote control.
- A delay of a quarter of an hour is set on the “open trunk” icon.
- For 20 m you need to press on the crossed out speaker.
After setting the desired position, it is recommended to leave the module alone for 10 seconds. After inactivity, the Tomahawk TW 9010 will automatically return to normal operation.
How to make a switch key?
The Tomahawk TW 9010 factory kit contains only two key fobs with a built-in antenna. There is no space for a key on the case. This circumstance does not suit some users, which forces them to redo the pager themselves. The upgrade procedure looks like this.
Buy a new transmitter housing with a turnkey socket. Disassemble the old case, using extreme caution - thin latches may break off or damage the internal circuitry of the module. Assemble the internal components of the signaling system onto the new housing in the reverse order. Disassemble the handle of the standard key and transfer the core to the mount in the new key fob.
After installing the battery, the remote control can be used as usual.
This procedure requires care and precision. It is easy to damage the sensitive elements of the module. This provokes some motorists to buy ready-made key fobs with a key mount and simply rewrite them into the system.
How to increase starter cranking time
In some situations, after long-term operation or severe cold weather, the initial cranking time of the starter may not be enough. The piston group begins to rotate, but the pick-up does not work. For such situations, the manufacturer has provided the possibility of increasing the starter operating time.
Enter the program by pressing Override three times.
The system allows the driver to set three modes:
- 800 ms – press the closed lock;
- 1200 ms – press the key on the key fob;
- 1800 ms – activated via the trunk open button;
- 3000 ms – you will need to click on the crossed out speaker.
In this case, the factory position is set exactly to 800 ms. It is assumed that the device will be operated in warm weather and with a working battery. Failures are logically explained by wear of the battery and freezing of oil in the crankcase compartment.
You can watch the calibration procedure in more detail in the video.
Tomahawk 9010: autostart programming table
It contains a complete description of the options configured using the service mode. Here is information about the sequence of actions and calibration of each option separately:
- duration of operation of the power unit after turning off the ignition and rotation of the strater;
- setting the temperature inside the car;
- motor control signals;
- activation of 2 additional modes;
- howler pulse duration;
- door control;
- engine start delay;
- duration of the central lock control pulse;
- safe driving;
- automatic activation of security;
- setting up interior lighting;
- setting for an hour warm-up;
- turbo timer control.
There is also information on how to program an alarm for a car factory or remote engine start. You can learn more about enabling functions from the table itself.
Possible faults
If autostart on the Tomahawk becomes impossible, you should consider possible malfunctions or take into account incorrect key fob settings. Sometimes the system simply malfunctions or does not respond to clicks at all.
The car stops starting, the ignition indicator does not light up, and the light signal from the headlights does not appear. Sometimes another problem occurs: the key fob is fully operational, but the engine does not autostart. There are also situations when, when the function starts, the ignition is turned on followed by a click, but without starting the power unit.
If autorun does not work, it may be due to the following problems:
- Problems with the ignition wiring.
- Start blocking with standard immobilizer.
- No power supply from fuse.
- Damage to the temperature sensor that provides automatic start.
- Incorrect installation of the system or incorrect configuration of functions.
- Problems in the control unit, when the tracks burn out during power surges.
- The sensor jumps out of the housing. A similar problem occurs when installation rules are not followed. If parts are not securely fastened, they will become deformed with intensive use.
If you are planning to purchase an expensive alarm system, you need to make sure that you can set it up yourself. Otherwise, failures and malfunctions may occur during system operation.
Automatic start of the car can be done from the key fob of the anti-theft system by pressing the desired combination of buttons. In order to set up Tomahawk 9030 autostart, thoroughly study the instruction manual. To enter the setup menu for this function, follow the steps.
- The ignition must be turned off.
- Press the Override key six times.
- The last step is to turn on the ignition. The siren will sound 6 times.
You can configure the following automatic car engine start functions:
- IGN 3 output mode: does not work when the starter is turned on, does not turn off when the starter is turned on, operates all the time the starter is turned on, works until the starter is turned on;
- monitoring the operation of the vehicle’s power unit and starter;
- gearbox type: automatic, manual;
- engines: diesel or gasoline;
- turbo timer operating time: off, running 1 min., 3 min., 6 min.;
- warming up the car: 5, 10, 15, 20 minutes;
- periodic autostart after 1 hour, 2, 4, 24 hours;
- protection during automatic engine start;
- operation of the dimensions and turn signals during autostart: blinking, constantly on, off;
- closing the doors after warming up.
Tomahawk 9030 alarm installation diagram:
How to disable autostart on Tomahawk 9010 from key fob
The autostart system is a necessary addition for comfortable vehicle operation. The activation of the mode is programmed in advance. How to remove the car factory at negative degrees or timed installation is described in the instructions. To do this, you must simultaneously press the combination of the key and the open cargo compartment. If the actions are performed correctly, the car will blink its dimensions twice, and the key fob will emit two chirps.
How to disable warm-up on Tomahawk 9010
The Tomahawk 9010 alarm system is equipped with the ability to independently warm up the internal combustion engine over time. Depending on the buyer’s wishes, the required operation intervals and operating duration can be set.
How to remove the car from the hourly warm-up when the timer starts, the factory instructions will answer.
According to the user manual, turning off occurs by pressing the key and the speaker. After deactivation, the car will emit two flashes with its headlights or turn signals, and the key fob will signal with a melodic trill.
How to install
When installing the complex, it is recommended to follow the conditions set out in the installation instructions. When choosing placement locations, you should ensure that the components are hidden; the parts are mounted away from heat sources and electromagnetic interference. The unit must be installed with the connectors facing down, ensuring that condensation is removed from the contact points. The siren is installed in the engine compartment; active type devices can be used. To place the impact sensor, an area is selected inside the car interior; the sensor must be rigidly attached to the base.
Wiring connection
The connection diagram provides for separate switching of the automatic start unit harness, the cables of the central locking module and the main connector of the processor unit. The shock sensors and antenna unit are equipped with separate harnesses with switching plugs. When installing the head unit on cars with automatic transmission, it is necessary to cut the jumper that ensures the autostart operation. On equipment with a manual box, the cable remains closed.
Tomahawk 9010: autostart does not work, the starter does not turn
The reliable design of the Tomahawk 9010 car alarm sometimes experiences failures caused by internal or external breakdowns. Usually this is due to simple reasons.
- The battery is worn out. To automatically start the power plant, more energy is required than in normal mode. The problem can be resolved by recharging the battery or replacing it with a new one.
- Autorun programming is broken. Usually small errors in the calibration procedure or an incorrect activation algorithm cause this. Corrected by carefully following the instructions. In this case, the machine does not set the alarm or refuses to perform the assigned tasks.
- Mechanical damage to modules. Faulty units cannot transmit pulses.
- Starter rotation time is too short. Oil freezing may require the unit to operate longer than in summer. To fix this, you can increase the amount of time in service mode.
Tomahawk TW 9010 does not start from the key fob: SP error
The electrical diagram and operating principle of the unit can help you understand why the automatic engine start option does not work. If the start with the key is successful, there is a loss of voltage in the circuit and you should check the main batteries:
- Battery charge and condition. An empty or worn battery can cause severe voltage drop.
- It is also recommended to check the power supply of the alarm itself. The fuse on the power core often oxidizes, which causes poor contact.
If the startup from the remote control is not initially programmed, a full system reset to factory settings may help. During prolonged operation of the unit, it is not uncommon for internal operating system errors to appear.
Starts and stalls
Some users complain that the car starts with the key fob and stalls after a minute or less. Usually the malfunction is caused by the low sensitivity of the sensors inside the Tomahawk TW 9010 alarm head unit. In 90% of cases, the problem occurs in winter, when negative temperatures make adjustments to the launch parameters.
To eliminate the malfunction, experienced motorists recommend reinstalling the launch limit controllers on the tachometer. This will help bypass the loss of energy at the starter and the lag in the oil pressure indicator.
You should not completely ignore the breakdown. A minor malfunction may hide a serious problem.
Why is temperature triggering disabled?
Correctly setting the warm-up temperature is an important part of calibrating the entire system. If the sequence of actions is violated, the module may not operate correctly or fail completely. External factors can also cause the defect:
- incorrect setting of the starter cranking time;
- broken sensor settings;
- Incorrect operation or connection of the temperature sensor.
You can fix the problem by fully diagnosing the electrical circuit of the Tomahawk TV 9010 sensor. In case of software failures, an absolute reset of the settings helps.
Why does autostart disappear?
Some users complain that in winter the engine does not start with the anti-theft system. The fact that auto-warming stopped working can be argued by three factors.
- Battery drain. The lack of starting currents affects the possibility of remote operation of the system. The car starts normally with the key.
- The frequency of automatic startup of the unit is too infrequent. In severe frosts, the oil in the crankcase freezes quickly. This circumstance prevents the normal operation of the unit.
- As a consequence of point No. 2, the starter cranking time is too short.
Car alarm turns on the ignition, but does not start
Similar reasons lie behind the fact that the Tomahawk TW 9010 activates the ignition, but does not turn the starter. Usually the problems are purely mechanical in nature:
- the power supply is faulty or worn out;
- the retractor relay or other starter components do not operate;
- The contact on the wire connection has oxidized or the fuses are damaged.
There is also a software failure. In this case, just reset the settings and everything will return to normal.
The warning light went off while warming up
When actively using the Tomahawk TW 9010, it happens that the unit begins to glitch or act up for no apparent reason. Motorists identify three problems from the general stream.
- When trying to start, the starter turns too little and the car does not start. Extending autostart in service mode completely eliminates the problem.
- During normal starting, the car quickly stalls and does not have time to warm up properly. There is an abnormal change in temperature at which the relay turns off.
- The opposite situation occurs when “braking” occurs in severe frosts. It is enough to increase the activation temperature of the switch (for example, from -30 to -15) and everything falls into place.
After resetting the settings, autostart stopped working
If the device malfunctions after updating it or resetting the settings to the factory state, you must carefully study the instructions. Without knowing the car model and how to connect the security system, it is impossible to accurately answer the question. However, the reasons that the power plant does not start in 70% of cases are the following factors:
- it is required to hammer in new calibrations for Tomahawk TW 9010;
- The starter cranking time is insufficient;
- the system needs firmware updating of equipment powered from an additional channel (gasoline pump, etc.).
In some cases, programming autostart using the tachometer helps. If in winter the limit switch is connected to the oil pressure sensor, the installation may also not work correctly.
Alarm description
As of today, the production of Tomahawk 9010 car alarms has been completed. But this model can still be found on sale in stores where it is in stock.
Key Features
This car alarm provides the consumer with the following opportunities:
- activation of silent security;
- reliable protection of door locks, as well as the luggage compartment and hood from opening;
- programming the start of the power unit based on temperature automatically;
- the ability to use the autostart option on cars with manual or automatic transmission;
- turbo timer designed to cool the engine boost system;
- the ability to install car alarms on cars with any type of power unit, including a turbocharger;
- measuring the temperature level in the car interior;
- option for self-diagnosis of all protection zones, bypassing the faulty one and warning the car owner about it;
- the presence of a two-zone touch sensor that detects activity and impact on the car body;
- option to disable the touch controller at a distance;
- function for calculating false positives;
- availability of three communication channels for connecting additional equipment;
- the “Panic” function, which ensures the activation of alarm signals and optical devices to scare away possible criminals;
- “Anti-robbery” mode, which allows you to block the operation of the power unit during a robbery attack on the car;
- the ability to configure basic parameters, as well as turn the alarm on and off using the Override service button;
- option to call the car owner to the vehicle;
- function of searching for a car in a parking lot;
- the presence of additional options on the key fob - alarm clock, timer, current time;
- turning off car alarms and unlocking door locks in two stages;
- the presence of a built-in relay for controlling the door lock closing system installed in the microprocessor module;
- the main console is equipped with five control keys, display backlight, and a warning system with a buzzer or vibration;
- protection of the control channel from scanning and interception of transmitted data;
- the ability to use additional communicators; in total, up to four remote controls can be registered in the control unit’s memory.
The AutoAzart channel briefly talked about the main capabilities and functions of the Tomahawk 9010 systems.
Advantages and disadvantages
According to reviews, in addition to the cost and availability of two-way communication, this alarm system is characterized by the following advantages:
- High quality assembly of component elements. All devices - key fob, microprocessor module, antenna and others are made in a durable housing. This helps prevent device failure due to mechanical damage.
- The control communicator is lightweight.
- Several modes to configure the remote engine start option.
- In urban environments, the operating range of the communicator is 150 meters. Although the manufacturer stated this parameter for 1200 m.
- Some users note such a drawback as small icons and indicators on the key fob display. It will take time to get used to them.
- The encoding used by the manufacturer to protect transmitted signals is in fact ineffective. Hijackers can use special tools in the form of a scanner to intercept impulses and commands. This will allow you to hack the anti-theft system.
- High sensitivity touch controller. If configured incorrectly, this will lead to false alarms.
- During the release of these models of anti-theft systems, defective alarms were encountered.
- Residents of northern regions may have difficulty managing the alarm, as it sometimes malfunctions in low temperatures.
- If there is strong interference, the connection with the communicator is interrupted. Over time, the buttons on the key fobs need to be pressed harder and several times.
- It is possible to randomly disable and activate various functions, which indicates problems in the operation of the microprocessor module.
User Oleg Baranov showed in practice how the installed Tomahawk 9010 alarm system functions.
Owner reviews
Motorists' opinions about the product. Miroslav.
Tell me how to increase or change the warm-up time? In winter the car does not want to warm up properly and after 2-3 repetitions it does not start at all. Where is this mode located?
Novel.
If the autostart without a key does not work in cold weather, only the complete instructions for the Tomahawk 9010 alarm system with autostart will help you understand where the dog is buried. I suffered with the alarm for more than two days, I could not understand what was wrong. It turns out that if you set the warm-up time every hour, the car simply does not have time to freeze (before this it stood for 2 hours).
Andrey.
I recently figured out how to set the start at a temperature of minus 20. I received the alarm already included with the car, and there were no instructions. Now we are sitting and redoing what the installers installed here.