Opel cars are very popular all over the world. These high-quality cars are perfect for Russian roads. Modern models of this automaker have everything you need. They are equipped with all the necessary electronic modules and components, which greatly simplify driving and the life of car owners.
However, even the most reliable vehicles cannot operate without failures. A large number of complex equipment causes breakdowns. Some of them are quite serious, while others can be easily corrected with your own efforts.
To understand what happened to the car, it is necessary to carry out diagnostics. As a rule, most machines have the ability to receive a report of possible faults. They are displayed on the dashboard in the form of digital and alphabetic symbols. If you know what the Opel Astra H error codes mean, you can avoid expensive repairs. Therefore, it is worth considering the most common problems and their designations. It will be useful to know what the numbers on the vehicle dashboard indicate.
Error code 59761 on Opel Astra H
As a rule, when such a code appears, the car owner notices that the vehicle stops warming up by more than 80 degrees. Some people in this situation decide to insulate the car on their own. For example, when error code 059761 appears on an Opel Astra H, some people use specialized car blankets or insulation for saunas. Often this helps correct the situation. Typically, such events lead to the car starting to warm up to 97 degrees when driving along the highway.
However, it is not always possible to get rid of error code 059761 on the Opel Astra H so easily. It may also mean that the malfunction is due to incorrect operation of the coolant (coolant) sensor. If you replace it, the car will start to warm up as expected. Therefore, if error code 59761 reappears on the Opel Astra H, it is worth carrying out a full diagnosis of the car. It's better not to delay this.
Error 000970
This code appears quite often when starting auto self-diagnosis equipment. It should be said right away that it does not mean serious damage. So no need to worry. Error code 000970 on the Opel Astra H indicates that several elements have short-circuited in the fuse box. This usually happens in conditions of high humidity, such as when it rains. Also, rather aggressive car washing can lead to a similar malfunction. Often, a high-pressure water jet is used to clean vehicles. As a result, the liquid penetrates into those parts of the vehicle where there should not be moisture, at least not in such quantities.
It is noteworthy that if the car has a high mileage, then along with these numbers, error code 001463 may appear on the Opel Astra H. 001462 also often appears. In this case, you need to check the solenoid valve. It is responsible for the proper functioning of the phase shifters, which, in turn, control the motor shafts. If additional error code 001463 appears on the Opel Astra H, it is necessary to thoroughly clean the contacts of the faulty unit. If such manipulations do not help in any way, then you will have to change the valve and gears.
If water comes into contact with metal conductive elements, this can trigger the oxidation process. You can correct the situation on your own.
How to get rid of the error
Of course, the easiest way is to go to a car service center and not have to worry. However, there will need to be a full diagnosis, which is not cheap. Therefore, when you see error code 000970 on the Opel Astra H, it is worth making a few simple manipulations that will help correct the situation. First of all, you need to purchase a lubricant, which will be needed when cleaning and processing electrical contacts. It is very important to get rid of traces of oxidation. You also need to ensure that electrical contacts are protected from subsequent harmful effects.
After such an error code appears on the Opel Astra H, it is important to carry out work in accordance with the recommendations. First of all, the car must be de-energized. To do this, you will need to disconnect the battery terminals. The next step is to find the fuse box and remove the protective cover from it. Next, the driver or technician removes the connector located in the front part of the module. In this case, it is necessary to carefully unscrew the three retaining screws in the block itself. However, it is worth remembering that they are not completely removed. Even if you make an effort, you won't be able to do it. You also need to find the bolt at the base and remove it.
After this, the part is completely removed and the contacts are cleaned. When all the necessary work has been completed, all that remains is to thoroughly apply lubricant to all electronic contacts. At the next stage, all that remains is to assemble the assembly in reverse order.
If similar error codes appear on the control panel on an Opel Astra H 1.6 or another model, it is additionally recommended to treat the engine ECU with protective compounds. The required connector is located above the filler cap of the power unit. The procedure in this case will be similar. It is necessary to treat with lubricant and install the element back.
It is worth noting that reading error codes on the Opel Astra H helps eliminate the need for expensive repairs. For example, code 000970 does not foretell anything terrible. This is not a critical error. But this does not mean that it can be left unattended for a long time. If the causes of such a malfunction are not eliminated, it can cause more complex damage. However, 000970 is not always accompanied by additional errors.
If, after all the manipulations of cleaning and lubricating the elements, this code still appears on the dashboard, then most likely the car’s wiring has been damaged. In this case, simple measures will not do. Therefore, it would be better to contact an experienced master.
It is also worth knowing the error codes for the Opel Astra H in Russian. Let's consider the main errors that occur most often based on the type of elements in which the breakdown occurred.
How to use the diagnostic connector?
Please note: since errors in a car have different statuses, the Check Engine light does not always light up when they appear (in our language, “Dzhekichan”). The driver may not even suspect that the vehicle is in partially serviceable condition. To diagnose, you need to connect to the control unit using a special scanner.
Diagnostics in general terms is carried out according to the following algorithm:
- A laptop or phone, on which proprietary software for data decryption (for example OP-COM) is pre-installed, is connected to the car’s control unit via the OBD2 connector. The Opel Astra H has a special block installed in the cabin. Usually it is located under the decorative trim near the handbrake. To connect and read errors, use a proprietary cable with a compatible interface (if you do not have a wireless device).
- Next you need to launch the software.
- In the program, we press a special button that starts checking the car. Sometimes the software will require you to select an engine, as well as a body type (station wagon, sedan or hatchback).
- The program starts checking. Once it is completed, all errors detected during the scan are shown on the screen. Based on the data received, the further sequence of actions to eliminate the breakdown is determined. Based on the selected program used for reading, the interface can also demonstrate the vehicle's performance.
READ Ford Fusion Cabin Filter Replacement
Problems with sensors
One of the most common malfunctions of this car has code 011014. This error means that there has been a malfunction of the sensor, which is responsible for the air temperature in the car’s power unit. In this case, you can wait a few days. Often Opel Astra N error codes disappear on their own. If this does not happen, then it is best to replace the sensor rather than try to repair it yourself.
Many also encounter the digital code 013604. At the same time, the car owner may notice an increase in fuel consumption. This happens due to a break in one of the oxygen sensors. Therefore, you need to replace the faulty element. However, it is also important to check the sensor wiring and connector. If you don’t want to solve the problem this way, then you should change the ECU firmware. If you set requirements no higher than Euro-2, then just one sensor will be enough.
If the car is manufactured in 2008, then there is a chance that sooner or later you will see the combination 006800 on the dashboard. It indicates that the throttle assembly is not working properly. If a similar error code occurs on the Opel Astra-H 1.6 Z16XER or in a car with a smaller engine capacity, you should pay attention to additional signs of component failure. First of all, vehicle owners note uneven idle speed. Some also pay attention to the increased consumption of the fuel mixture. In this case, most likely, the problems are due to the fact that the plastic cover through which the so-called air leak occurs is damaged. It needs to be replaced with a new one and the machine needs to be re-diagnosed.
Most often, car owners are faced with problems related to the performance of certain sensors. However, there are also situations when a digital code notifies about malfunctions in the power unit.
Engine errors
If the “Check Engine” icon lights up on the dashboard, you need to pay close attention to this warning. As a rule, it is accompanied by the Opel Astra-H error code 030101, 030201 or 030401. In this case, it most likely means that misfires have begun to occur. If we talk about additional “symptoms,” then car owners often note the appearance of jerks while the car is moving. The engine "triples". Additionally, there is an increased consumption of the fuel mixture. If this happens, then it is necessary to evaluate the condition of the ignition module. Often this particular unit fails. Unfortunately, it is almost impossible to repair it, so you will have to make a complete replacement.
If the car has a high mileage, then error code 212052 may appear on the Opel Astra H. Such a digital notification indicates that dampness has occurred inside the electronic pedal. Or some of its modules were dirty. In such a situation, it is worth paying attention to how often the check engine light comes on. If this only happened once, then there is nothing to worry about. Most likely, the dirt will soon fall off or dry out and the operation of this unit will be restored. If another substance gets on the connector and cannot simply evaporate, the error will appear again. In this case, you need to disassemble the electronic pedal and thoroughly clean the contacts.
Owners of new or relatively “young” cars may encounter error code 001161 on the Opel Astra H. As a rule, the malfunction appears immediately after the car owner tried to replace the timing belt on his own. It is worth checking how correctly the valve timing functions. The shafts may have been installed incorrectly. Also, such errors often appear if the phase regulator sensors work with errors. It is necessary to conduct a clearer diagnosis and identify the exact problem.
Among the Opel Astra-H error codes there are also those that inform the vehicle owner about problems related to the condition of the wiring. Most often, such problems are also not critical, but it is not recommended to ignore them.
Carrying out car diagnostics yourself
To carry out diagnostics, it is necessary to perform certain actions that differ for vehicles with manual and automatic transmission.
210111 - malfunction
The throttle motor is faulty or clogged. Usually it is enough to clean the mechanism from dirt and dust. In the latter case, the device is completely replaced.
Astra code АШ: 0 30 101
Misfire in one of the cylinders. The engine control systems, ignition and electrical systems should be checked.
34004
The camshaft position sensor is damaged or faulty. A problem occurs very rarely, but when it occurs, the car begins to be finicky or refuses to start at all. The fault can also be found under number 034004.
Error 3608
The oxygen sensor heater is faulty or damaged. To perform diagnostics, it is recommended to check the detector line. Depending on the electronics version, there are also designation options:
4205A - malfunction
The catalyst is damaged or clogged. It may also indicate a breakdown in the housing or scattering of cells. It may be indicated as 04205A, which means that the device should be replaced immediately. But in Russian conditions, it is simply cut out of the main line by welding a piece of pipe of suitable diameter.
Also designated as 006800 and indicates damage to the throttle valve. If the diagnostics has established the fact of wear, the unit is completely changed.
Error 1166
It occurs after replacing the timing belt on a 2008 car; it can also be displayed as 001166. To resolve the problem, you will need to check that the marks are set correctly.
P1700
Transmission lever cables are damaged or overheated. The machine may run jerkily or jerk.
For automatic transmission
If your car is equipped with an automatic transmission, you can read the error code like this:
Errors related to car wiring
Car owners who have extensive experience driving Opel Astra cars are well aware that this vehicle often suffers from oxidation of contacts located in the safety and control units. However, this is far from the only problem.
For example, if a driver notices the appearance of error code 170000 on an Opel Astra H, then most likely it is also about a vehicle. As a rule, there is a problem with gearbox shifting. The checkpoint begins to react poorly to manipulation. If we talk about the reasons for this, then such consequences are caused by rotted wires that are connected to the gearbox itself. There are other faults, but they can only be identified through more accurate diagnostic measures.
Also, the car owner can pay attention to the appearance of error code 062104 or 062103 on the Opel Astra H. In the second case, we are talking about rotting of the wires going to the generator. The diode bridge could also burn out. Often such a malfunction is accompanied by the activation of an icon on the dashboard informing that the battery is low. To restore the system, you will have to replace the bridge or damaged section of wiring. It is also recommended to clean the contacts if they are oxidized.
If there is an error code on the Opel Astra H 62104, then in this case the problem is definitely related to damage to the diode bridge. It needs to be replaced.
Other faults
If you look at the list of Opel Astra H error codes, you can find the basic definition of the malfunction. In most cases, this allows you to independently adjust or replace the desired unit. Among the less common errors is code 017011. In this case, it is worth paying attention to the composition of the mixture, which is most likely too lean. Among the additional signs of malfunction, it is worth highlighting increased fuel consumption. As a rule, it starts to be about 2.5 liters per hour. The main reason for this malfunction is damage to the brake element vacuum booster membrane. Because of this, air is not sucked into the motor correctly. Sometimes, when idling, the car owner even hears the air starting to hiss in the body. The only way to get rid of the breakdown is to completely replace the vacuum seal.
Similar problems are observed when the numbers 017012 appear as an Opel Astra H error code. In Russian, this malfunction sounds like “too lean mixture.” In this case, the problem may be the same as described above or be associated with a malfunction of the oxygen sensor. There are other malfunctions that do not bother car owners so often.
For example, error code 11517 “Opel Astra H” indicates a failure of the sensor responsible for the operating temperature of the engine. It is located in the thermostat. In fact, the problem is similar to code 059761, since we are talking about problems with the coolant. However, in this case, most often the problem lies in the so-called chip, a small part of the thermostat. Similar problems are indicated by error code 218217 on the Opel Astra H. In this case we are also talking about a temperature sensor. But this designation is found much less frequently among vehicle owners.
In addition, code P0195 may occur. It stands for problems associated with too hot lubricant poured into the car’s power unit. Also in this situation, it is worth checking the proper operation of the corresponding controllers.
If there is a sharp increase or decrease in the level of fuel fluid in the gas tank, then P0460 will appear on the control panel. In this case, you will have to check and, most likely, replace the fuel sensor.
It is also worth paying attention to the last digits of the code. Sometimes they say that the error is due to improper operation of the ABS system. For example, if the number 35 appears on the panel, car owners should check the pumping equipment, or rather, its electrical part. Often it is in this node that a short circuit occurs or some of its elements are damaged. When this error code appears, the system notifies the car owner that it cannot receive a response from the pumping equipment. In this situation, it will have to be repaired or completely replaced.
Code 37 may also appear. If the driver sees it, then it is most likely that the pedal responsible for the brake is malfunctioning. As a rule, the problem is solved by restoring the broken wiring.
When code 45 appears, it is worth checking the functionality of the electrical circuit that is connected to the rear wheel, or rather, its sensor located on the left side of the vehicle. The controller you need is probably missing or damaged. In this situation, you need to replace or install it.
If the code contains 48, then you should pay attention to the microprocessor indicators. Most likely, the voltage in the on-board system has increased too much. In this situation, it is recommended to carry out diagnostics and make sure that the battery and the generator are working properly. The battery must be carefully inspected. Perhaps its integrity has been compromised. You also need to make sure that there is electrolyte inside the battery. Additionally, it is worth purchasing a multimeter. Using this device, which is desirable for every car owner, you can check the power supply and voltage of the vehicle's electrical network.
Reading and deciphering codes in Russian
To make it easier to read errors, all faults are divided into categories. There are thousands of codes in total; below are the Russian designations that are most common.
Sensor malfunctions
Deciphering error codes for sensor faults.
| Error code | Description of the malfunction and recommendations for elimination |
| P0100-P0113 | Problems have been reported in the operation of controllers designed to determine the volume of flow and temperature of the air supplied to the engine. The reason may be problems related to the operation of the sensors, a power short to ground, damage to the electrical circuit, or an incorrect signal. To diagnose, you need to check the integrity of the power line, the quality of the contacts and, if necessary, clean them. If the circuit is intact, then the controller changes |
| P0115-P0118 | Problems with the refrigerant controller. The sensor may be faulty or the power line to which it is connected may be damaged. The steps to diagnose and identify the problem are similar. With such a malfunction, information about the temperature of the power unit may be displayed incorrectly on the instrument panel. The controller needle can rise or fall arbitrarily, or even “lie” at the zero mark |
| P0120-P0123 | The microprocessor module has detected problems in the functioning of the throttle valve position controller. Detailed diagnostics of the sensor and wiring is required |
| P0130-P0167 | There were problems with the operation of one of the lambda probes. The error may appear as code 013611 |
| P0176-P0179 | The microprocessor module detected problems associated with the CHX signal |
| P0180-P0188 | Malfunction in the operation of fuel control sensors A or B. A detailed check of the devices is required |
| P0190-P0194 | The microprocessor module detected malfunctions in the operation of the fuel pressure level fixation controllers |
| P0195-P0199 | The electronic module reports that the temperature level of the lubricant in the engine is outside the normal range. The malfunction may be due to incorrect operation of the controller. Sensor diagnostics required |
| P0220-P0229 | The throttle sensor has failed |
| P0235-P0242 | The microprocessor module has detected a malfunction in the operation of the turbine controller, as well as the turbocharger |
| P0325-P0334 | Problems with the detonation controller. The power unit may “knock” and a metallic sound can be heard from the engine compartment. It manifests itself especially clearly when driving at low speeds uphill. |
| P0340-P0344 | Problems have been recorded in the functioning of the camshaft controllers, and a possible timing shift. It is necessary to check the device in detail |
| P0385, P0386, P0389 | The crankshaft position controller is not functioning properly. There may be an incorrect signal coming from the device, there is a possibility of damage to the wiring or short circuit. The causes of sensor malfunction are often associated with dirt getting on the connector, then the block must be cleaned. With this problem, it may be difficult to start the engine. |
| P0403-P0408 | Incorrect operation of the exhaust gas recirculation system. The reason may be that the sensors are not working |
| P0450-P0454 | The microprocessor module detected that the fuel vapor pressure parameter was outside the normal range. You need to check the system controller |
| P0460-P0464 | The fuel level controller in the tank is not functioning correctly; the fault must be found in the sensor or its wiring. One of the signs of a problem is incorrect display of information about the volume of gasoline on the dashboard |
| P0465-P0469 | Malfunctions in the functioning of the controllers for supplying air flow to the purge system |
| P0470-P0479 | There was a problem with the functioning of the pressure controller in the exhaust gas system. It is necessary to check the device in more detail for the integrity of wires and contacts |
| P0500-P0503 | Malfunctions have been detected in the functioning of the machine speed controller. With this problem, the speedometer may not work correctly. |
| P0520-P0523 | Malfunction of the engine fluid pressure controller. These combinations report an incorrect signal emitted by the sensor |
| P0530-P0533 | Incorrect pulse signal from the controller designed to monitor the refrigerant pressure level in the air conditioning system. Diagnostics of the sensor for possible breaks and short circuits is required |
| P0550-P0554 | The microprocessor module detected an incorrect pulse signal from the power steering controller |
| P0608, P0609 | Malfunctions of controllers A and B of the power unit control system |
| P0656 | Malfunction in the electrical circuit of the fuel level controller. Problems must be looked for in the wiring. Power line diagnostics are performed using a multimeter |
| P0703 | The microprocessor module has detected problems in the electrical circuit of the controller designed to reduce torque during braking |
| P0704 | Damage to the electrical circuit of the clutch system controller has been detected; the wiring may be broken. It is necessary to check the power line for integrity |
| P0705 | Malfunction in the electrical circuit of the transmission controller. You need to check the wiring with a tester. |
| P0706-P0709 | Microprocessor module reports incorrect operation |
| P0710-P0714 | Problems have been recorded in the operation of the lubricant temperature controllers in the gearbox. If the sensors are intact and working, then the reason must be sought in the integrity of the power line |
| P0175-P0178 | Problems in the functioning of the turbine speed controller |
| P0179, P0724 | The microprocessor module detected a signal outside the operating range from the torque reduction controller during braking. You need to run device diagnostics |
| P0720-P0723 | The crankshaft rotation controller is not functioning stably. Possible problems starting the engine |
| P0725-P0728 | The power unit speed controller sends an incorrect signal to the microprocessor module. A thorough check of the device and the electrical circuit to which it is connected is required. |
| P1106, P1107 | The ECU receives an incorrect pulse signal from the intake manifold pressure controller. It is necessary to check the operation of the sensor in detail |
| P1114, P1115 | There is a problem with the power line of the refrigerant level controller. The sensor may break, but first of all you need to check the circuit. The cause of the malfunction may be damage to the contact elements on the block |
| P1121, P1122 | Malfunction in the functioning of the throttle position controller. You need to check the connection circuit of the device |
| P1463 | If error 1463 occurs, the microprocessor module reports a malfunction in the functioning of the ACP pressure controller |
| P0365 | Error 0365 or 036504 indicates a malfunction in the camshaft sensor. There may be interruptions in the operation of the power unit. Detailed diagnostics of the controller and the power line to which it is connected is required |
Pavel Menshakov spoke in detail about solving problems associated with the operation of the camshaft and crankshaft synchronization controllers.
Engine and gearbox malfunctions
Deciphering error codes for engine and gearbox faults.
| Code | Description of the problem |
| 030101, 030201, 030301 | Such error codes indicate misfires recorded by the microprocessor module in one or more cylinders. The power unit of the machine will function unstably. There may be jerking, tripping of the engine, as well as increased fuel consumption. The problem may be caused by a breakdown of the ignition module; on Astras it often breaks down. The problem cannot be resolved by repairing the device; it will need to be replaced. |
| 212052 | This combination is more typical for cars with high mileage. The problem is often caused by contamination or oxidation of the contacts on the electronic gas pedal block. Sometimes the error disappears on its own when the dirt dries and falls off. But in order to achieve a more effective result, it is recommended to disassemble and clean the contact component on the pedal |
| 000970 | The microprocessor module reports a mismatch in the operation of the CAN module; this may be due to the random disconnection of the battery while driving. Often the error goes away on its own after some time. |
| 001462, 001463 | Malfunctions in the operation of one of the electromagnetic valves of the camshaft phase shifters of the power unit. To fix the problem, you can try cleaning the contact elements. If this does not help, you will have to replace the valves. The camshaft gears also change along with them. |
| 00161, 001166 | The valve timing is set incorrectly; you need to make sure the pulleys are installed correctly. In practice, these malfunctions often appear as a result of replacing the timing belt. Sometimes the reason may be due to improper functioning of the solenoid valves of the phase control device |
| P0201-P0204 | Malfunctions in the operation of the fuel injector of one of the cylinders of the power unit. The problem may be a damaged electrical circuit. It will require diagnostics and replacement of the damaged area. |
| P1700 | There are several reasons for this malfunction, but it is typical only for cars with automatic transmission. This may be a malfunction of the gearbox shift system. Sometimes the problem is caused by an over-enriched or lean exhaust; a signal about this comes from the O2 sensor. The reason may be that the transmission control module needs to fulfill a request for suitable maintenance intervals. |
| P0217 | Overheating of the power unit. There can be many reasons for the problem; detailed engine diagnostics are required. |
| P0218 | Transmission overheating. Transmission system diagnostics required |
| P0410 | Problems were detected in the functioning of the secondary air supply system |
| P0731-P0736 | The transmission gear is incorrectly adjusted. Requires detailed diagnostics and adjustment |
| P0172 | An enriched combustible mixture is recorded in the cylinders of the power unit |
| P0420-P0434 | The microprocessor module recorded a reduced efficiency of the catalyst system. The problem may be with the heating device |
| P0574-P0580 | Problems in the functioning of the cruise control system; detailed diagnostics of all components is required |
User Alexander Sun reported on the procedure for reading errors and solving one of the problems associated with the operation of the Opel Astra engine.
ABS system errors
ABS system fault codes will be displayed in two digits.
| Combination | Description of the problem |
| 16 | The microprocessor module detected problems in the electrical control circuit of the solenoid valve of the left wheel located at the front. If the malfunction is related to a broken power line or a short to ground, it will be diagnosed immediately. If the winding of the solenoid device is shorted or shorted to voltage, the problem can be identified at a speed of more than 6 km/h |
| 17 | Similar problem with the right front wheel. To find a fault, you need to ring the electrical circuit. |
| 18 | Short to ground or open circuit in the control line of the rear brake circuit valve solenoid. To diagnose the problem you will need a multimeter |
| 19 | This error indicates a malfunction in the electrical circuit of the valves; the problem may be associated with a break or short circuit to ground. During diagnostics, the problem is detected when the ignition is on or when the car is moving. When testing occurs, information about the problem is entered into the memory of the on-board computer if the voltage on the device is more than 5 volts. This should happen within 30 seconds. After diagnostics, the error persists if the voltage parameter that affects the relay is more than five volts for 20 ms |
| 25 | The microprocessor module detected problems in the operation of the gear pulley of the wheel speed determination controller. Information about the malfunction is recorded in memory if the rotation speed of a wheel is 25% greater than the speed of other wheels for two minutes. It also persists when the wheel slips by 4.5% for the same time |
| 35 | The electrical circuit of the return pumping device is damaged or short-circuited. A malfunction is recorded in memory if the pumping device responds for more than five seconds without turning on the relay. The error is also stored in memory if the pump does not respond within 40 ms after the relay is turned on or within 100 ms after testing is completed |
| 37 | Faults have been detected in the electrical circuit of the brake pedal switch. The microprocessor module reports a wire break. Detailed diagnostics of the line and restoration of its functionality are required |
| 39 | The controller installed on the front left wheel is sending an incorrect signal. |
| 41 | The on-board computer detected damage in the electrical circuit of the left front wheel. But the problem may be caused by a breakdown of the controller installed on it, or a break in its power line |
| 42 | The controller installed on the front right wheel gives an incorrect signal |
| 43 | Problems in the operation of the electrical circuit of the sensor installed on the front right wheel. The controller may be missing. You need to make sure it is present and check the operation of the sensor |
| 44 | The controller installed on the rear left wheel gives an incorrect signal. Line diagnostics required |
| 45 | The microprocessor module has detected malfunctions in the operation of the electrical circuit to which the rear left wheel sensor is connected. The device may be missing or damaged |
| 46 | An incorrect pulse signal is supplied from the rear right wheel controller. Detailed circuit and device diagnostics required |
| 47 | The microprocessor module has detected malfunctions in the operation of the rear right sensor circuit installed on the wheel. The power line may be broken, the controller itself may be missing |
| 48 | The control module detected low voltage in the on-board network. A detailed diagnosis of the operation of the battery and generator device is required. The battery must be checked for integrity and make sure there is an electrolyte solution inside. Using a multimeter, you check the voltage in the machine's electrical network. |
| 55 | The control unit is not working correctly. If the microprocessor module is faulty, problems may occur in different car systems |
The channel “Sports and Entertainment Favorite Rocking Chair” spoke in detail about the procedure for diagnosing the ABS system in an Opel Astra car.
Other errors
This table of Opel Astra N error codes shows faults that were not included in the previous sections.
| Code | Description of the problem and recommendations for resolving it |
| 161450 | Problems with the engine blocking system. The control device informs the car owner that the immobilizer unit did not recognize the installed key. The problem may be due to an erroneous reading of the transponder tag or a lack of communication between the devices. A malfunction may occur after installing the anti-theft system. To eliminate it, you need to test the operation of the immo and, if necessary, install a blocker crawler. CAN bus diagnostics required |
| 000970 | The microprocessor module reports the closure of the contact elements in the safety block. The reason may be that moisture has entered the device. It is necessary to diagnose the oxidation of the contact elements and, if necessary, clean them. If moisture gets on the unit, the device must be dismantled and disassembled, then dry the internal board |
| 30201 | A misfire is reported in the second cylinder of the engine. To fix the problem, you need to clean the injectors, as well as the fuel filter device. It is necessary to diagnose the serviceability of the oil pressure controller, as well as the pump, ignition module and spark plugs. All faulty elements must be replaced or repaired |
| 059761 | There is a malfunction in the functioning of the refrigerant control valve on the thermostat. The cause may be damage to the circuit, but sometimes it should be looked for in the contact elements. The best option would be to replace the thermostat |
| 001463 | Malfunction in the exhaust camshaft synchronization system. The solenoid valve needs to be replaced, otherwise the gears may break. |
| 170000 | Malfunctions in the functioning of the transmission system. More detailed diagnostics are required to find the cause of the problem |
| 011014 | Problems in the functioning of the controller designed to determine the temperature of the intake air. First of all, you must check the mounting of the sensor and the integrity of the power line to which it is connected |
| 161600 | The microprocessor module detected an incorrect SIM identifier. CAN bus diagnostics required. The reason may be poor contact |
| 017012, 017011 | There are several reasons why these fault codes appear. This may be a malfunction of the fuel volume adjustment system in the first block, an inoperative O2 controller, or a faulty USR valve. Sometimes the reason is clogged exhaust gas system channels. |
| 001161 | Literally, the error stands for incorrect position of the mechanical synchronization of the intake camshaft, outside the operating range. Problems may be caused by problems with the device. Similarly, the malfunction is described by code 001166 |
| 59761 | The thermostat requires diagnostics; there is a possibility that the valve of the device is stuck. Because of this, problems may arise in the operation of the cooling system as a whole. Possible overheating of the power unit |
| 062104, 62103 | The microprocessor module has detected problems with the operation of the IPC generator device. Also, the reason may be due to damage to the electrical control circuit for light bulb L. If it is burned out, the indicator light will need to be replaced. Signs of a malfunction include sudden activation of the lamp when the power unit is running and its abrupt shutdown |
| P1607 | Malfunctions in the clutch drive control system. Node diagnostics required |
| 119167 | It is necessary to diagnose the electrical circuit to which the fuel metering valve is connected. The problem may be low pressure in the fuel line. With such a malfunction, the engine may not operate correctly, in some cases it will randomly turn off. The engine may detonate and its speed will begin to decrease. |
The “IZO))) LENTA channel spoke in detail about the procedure for diagnosing and reading combinations of faults in the memory of the Opel Astra N on-board computer.
How to reset the error
Why does it happen that the driver has made every effort to correct the problem, but the error still continues to appear? No, these are not problems in the dashboard. The fact is that as soon as the control unit receives a signal about a particular breakdown, it records it in memory. Therefore, numeric and alphabetic characters may continue to appear for some time. This will stop as soon as the microprocessor overwrites the updated information and stores it in its memory module.
But in this case, the car owner has to wait until this happens. Of course, when it's important to understand whether a problem has been fixed, no one wants to be left in the dark. In this case, the easiest way is to use the ODB II tester (any model will do). In addition, you should try to remove the error indicator yourself by using InSP service. To do this, you only need to perform a few simple manipulations.
First of all, you need to turn on the ignition. After this, you need to hold down the button that is responsible for resetting the daily mileage of the car. After a few seconds, the display should show an indicator and a corresponding message containing InSP. Continuing to hold down the key, you need to press the brake and start the engine. The button is not released. With the key and pedal held down, the car owner must wait about 15 seconds. The display will show “InSP 35000” or “InSP 50000” if the vehicle is diesel. The light will blink for a while and go out. After this, re-recorded errors should not appear unless the driver failed to correct them.
Resetting service intervals
On the mileage display, depending on its value (usually around 8000-10000 km), the inscription InSP appears.
IsP message on panel
This is an indication of the time until service maintenance. How to reset it? Please note that resetting the maintenance interval must be performed correctly to avoid errors in the operation of the vehicle.
- Turn off the ignition.
- After the daily mileage is displayed on the display, press the “reset” button.
- While holding reset, turn on the ignition. Note: The reset button must be held for at least 10 seconds. The screen will first display a flashing InSP indication, then the maximum mileage.
- When the inscriptions stop flashing, it indicates that the maintenance interval has been reset to its initial state.
How to perform self-diagnosis
Modern cars are able to inform the car owner about possible breakdowns. To make such a diagnosis, you should first of all always pay attention to the light icons that light up on the dashboard.
You can also use a special diagnostic scanner. It should be connected to a laptop or smartphone and read all the necessary error codes in the operation of vehicle systems. Moreover, such scanners not only provide the necessary digital designation, but also decipher it.
However, not everyone has such a device. Fortunately, you can do without it. You just need to display the necessary information on the LCD display of the vehicle control panel. If we are talking about a vehicle equipped with a manual transmission or a gearbox, which is popularly called a robot, then you only need to complete a couple of steps. While driving a car, the car owner must lightly press the brake and gas pedals at the same time. Don't try too hard, just a little touch is enough. In this position you only need to wait a few seconds. After this, continuing to press both pedals, you need to start the engine and wait a few seconds. A six-digit code should appear on the monitor. It will contain information about the error, if any.
If we are talking about an automatic transmission, then the manipulations will be somewhat different. To activate the code messages, you must turn on the ignition and press only the brake pedal. The force applied is also average. After this, the gearshift knob is moved to position “D” and the car owner turns off the ignition and also releases the pedal. At the next stage, it is enough to simultaneously press the gas and brake with both feet and turn on the engine. After a couple of seconds, a digital code will appear on the dashboard.
Photo gallery
The photo shows examples of error codes in the Opel Astra.
Malfunctions in the functioning of the transmission system
Malfunctions in the functioning of the intake air temperature detection controller
Malfunction in the exhaust camshaft timing system
Features of error decoding
It’s not enough just to find a translation of the most common notations. You need to be able to break the error code into several parts. For example, the first four characters (letters or numbers) indicate the fault itself. The other two numbers indicate its meaning. In some situations, a 5-character code may appear. In this case, when searching for the required decryption, it is enough to put “0” in front of them.
The letters usually do not appear on the dashboard. However, when searching for errors in tables, they are almost always used. Using these symbols, it is much easier to determine which node failed. Therefore, it will be useful to know the meanings of these letters in a little more detail:
- B - usually placed before a code that indicates problems with electrical components. For example, this symbol can be seen in errors in power windows, switches, door lock controls, airbags and many other malfunctions of this type.
- If the digital code is preceded by the letter “C,” then you need to look for the problem in the chassis of the vehicle. The numbers will tell you about a more specific direction.
- P - indicated in gearbox errors or blocks responsible for the operation of the machine’s power unit.
- U - usually placed before a code that indicates problems with electronic control units. For example, a similar symbol may indicate that the parking sensors or airbag ECU is faulty.
For example, a car owner sees error code 161450 on an Opel Astra H, preceded by ECN. Despite these letters in the decoding tables, only one can correspond to such a meaning. Since the main code is 1614, you need to find P1614 and read the description of the possible malfunction. This error means that there is a malfunction in the immobilizer or key chip.
The last digits (if we take the value from the example, it will be 50) use symbols that determine the class of the problem. If the check engine light comes on, you need to pay attention to the numbers that will appear at the end. These symbols have the following meanings:
- If there is a “0” at the end, then in this case we are talking about a common code for the ODB II diagnostic node.
- The numbers “1” and “2” indicate that the probable error is related to the operation of the systems responsible for the fuel supply.
- When there is a “3” at the end, you need to pay attention to the ignition circuits.
- The number "4" symbolizes auxiliary nodes. Your catalytic converter assembly may be malfunctioning, or it may be time to check your evaporative emission control system. This symbol may also indicate other problems, which the preceding numbers will tell you in more detail.
- “5” means that the sensor that controls the car’s idle operation could have failed.
- If the number “6” appears at the end of the code, then most likely there is a failure in the vehicle’s electronics.
- The symbols "7" and "8" may also be present. As a rule, they indicate that you need to check the performance of the transmission.
By and large, the last digits mean what serial number is assigned to the error. For example, the same P1614 code can be divided into several parts. The first letter “P” indicates that you need to look for a fault in the transmission ECU or the power unit itself. Next comes the number “1”. This is a standard error code that is set at the factory during the production process of the car. After this comes "6". This symbol means that the problem may lie in the electronic or electrical circuit. At the very end there is “14”. These two digits indicate the common fault number. Thus, knowing the more precise meaning of all symbols, you can find comprehensive information about a specific breakdown.
Many are also interested in whether the alphanumeric values may differ depending on the type of power unit. It is worth noting that it does not matter whether a diesel or gasoline engine is installed in the car. The body type doesn't matter either. In sedans and station wagons these figures will be the same. Therefore, the error codes for the Opel Astra H 1.9 CDTi will not differ in any way from the definitions of faults in cars with a gasoline engine of the XER series.
After identifying an error, it is worth assessing the severity of the problem. If the car owner has the necessary knowledge, then he will be able to correct the situation on his own. However, if errors reappear, it is worth considering a full diagnosis. It can be done at a service center. It is also worth always having on hand a small diagnostic device that transmits all the necessary information in real time to a smartphone or computer. Thanks to such simple and easy-to-use devices, you can not only perform independent diagnostics, but also monitor fuel consumption, system condition, and so on.
Diagnostics of Opel Astra H without a scanner
To read errors on your car, you don’t have to go to a service center or buy a scanner. There is an option to use one of the two methods below. Much depends on which gearbox is installed on the car - manual/robotic or automatic.
Second character
The second character usually doesn’t interest us, but still:
ELM327 - cheap, but non-functional
There is a whole pack of Chinese scanners based on the ELM327 chip. There are devices with different interfaces - WI-FI, bluetooth, USB. Their main advantage is their low price and the ability to work wirelessly.
At the time of preparation of this material, But his work is associated with a number of nuances:
Budget error scanner OP-COM
OP-COM scanners are divided into two categories. The first includes models that support synchronization with vehicles manufactured before 2012. The second category is devices that, accordingly, are designed to synchronize with more modern cars.
After connecting, the device will be able to run self-diagnosis Opel Astra , based on the results of which the user will see the errors recorded in the ECU.
The main difference from the ELM327 is the ability to diagnose almost all errors, as well as the presence of some service functions, for example, adaptation of the robot’s gripping point.
Calculator: converting errors to OBDII format
If you don't know the error code in OBD2 format, use the translation tool
