Considering the driving culture and the state of domestic roads, there is no need to talk about the benefits of a DVR. And if until recently an ordinary video camera on a suction cup was a source of pride for a car owner, then the functionality of a modern recorder is comparable to the capabilities of a computer. Below we will look at the selection criteria and consider how to install a DVR with a rear view camera, depending on its design and your wishes.
Let's talk about the main thing right away: decide on the type of device. There are only two of them:
— classic is a separate two-channel display that is installed on the dashboard or windshield;
- a mirror with a built-in front camera and a connector for connecting a rear view camera - combines the functions of a mirror and a display, mounted on a standard mirror in the cabin or replaces it.
The obvious advantage of the second option is the possibility of permanent installation. At the same time, the windshield and dashboard are not cluttered with additional gadgets, and the DVR itself, outwardly indistinguishable from an ordinary mirror, does not arouse interest among unscrupulous citizens.
Both types of two-channel DVRs of the latest generation with a remote rear view camera are equipped approximately the same, and their installation differs only in the way the display is mounted. More about this.
Installation of a DVR mirror with a rear view camera and connection
The complete set of the mirror-video recorder includes: the mirror-monitor itself with a built-in front camera, a charger from the cigarette lighter, a rear view camera, a 5-meter connecting cable, a set of fasteners (Fig. 1).
Rice. 1 – Complete set of mirror-video recorder
If you have chosen the right mirror, you can quickly and easily fix it to the standard one using two elastic straps. Otherwise, you will have to dismantle the old mirror and purchase a separate mount for the new one.
How to connect power
Like a regular electrical device, the DVR can be connected to the on-board network anywhere, observing the polarity and the voltage consumed by the device, which is usually 5 V.
Depending on the make and model of the car, some of its electrical appliances are under constant voltage, and some are turned off along with the ignition. This moment determines the choice of wire to which you connect.
The supplied charger provides power from the vehicle's 12-volt network. At the same time, in many models of DVRs, the cigarette lighter plug is equipped with a voltage converter from 12 volts of the on-board network to 5 volts consumed by the camera itself. Therefore, if you are not strong in electrics and do not want to buy a separate converter, you should not cut off the charging plug - it is better to purchase an additional cigarette lighter socket, which will connect to the desired contact. In addition, such an installation will allow you to keep the DVR with a rear view camera intact for the period of warranty service.
Before starting work on connecting the gadget, remove the negative terminal from the battery.
To the cigarette lighter
The length of the charging cord allows it to be routed under the roof trim and front right side pillar trims, and then led directly to the cigarette lighter or into the glove compartment with an outlet. If you regularly use a cigarette lighter to charge other devices, consider this type of splitter as a tee with switches - a very useful device for long trips.
With this connection, recording is activated automatically when the engine starts. After turning off the ignition, the device turns off. But if the DVR has a built-in battery and motion sensors, it can activate recording even when the engine is turned off.
To the interior lamp
This is the shortest way and the easiest way. You just need to remove the ceiling cover and find the positive wire. At the same time, it is important not to confuse it with the one that comes from the relay that reacts to the doors, otherwise the recording will turn on every time they are opened.
Since in the vast majority of cases the interior lamp is under constant voltage, the DVR will also be constantly active.
To the fuse box
It is usually located at the bottom of the front or side of the panel. On the cover of the block there is a diagram of the location of fuses for electrical appliances (Fig. 2). Having chosen the appropriate one, you need to pull out its fuse, secure the red wire from the cigarette lighter socket to the positive terminal and insert it back (Figure 3). The negative contact - ground - goes to the mounting bolt. (Figure 4)
Rice. 2 – Layout of fuses for electrical appliances
Rice. 3 – Terminal
Rice. 4 – Negative contact
With this connection option, the DVR will turn on when voltage is applied to the electrical appliance you have chosen. If the latter is under constant voltage, you will need to turn off the recorder manually.
To battery
A good way to power the DVR is a separate dedicated line. The connection is similar to the previous one: the wire is led out under the hood to the fuse box - plus to plus, and the minus can be fixed directly to the car body.
If, in addition to the cigarette lighter connector, you also purchase a power controller, you can independently control the voltage supply to the camera.
Required accessories and installation sequence
On Lada Kalina 2, the camera is most often installed above the license plate. Usually, the standard design of Russian cars does not require a camera to view the space behind the car. However, you can install the device not only at a branded service station, but also yourself. This can be done especially easily on cars such as the Lada Kalina and its second-generation model of the same name.
You can notice it when you zoom in
To install a rear view camera, you need to strictly follow the instructions and prepare the necessary accessories, as well as remove the tailgate trim in advance.
Tools you will need to install a video device yourself:
- crosshead screwdriver;
- a set of open-end wrenches or sockets;
- suitable diameter drill bit, drill or screwdriver;
- The device itself - the rear view camera - is universal and, depending on the configuration, can be installed in any vehicle.
The rear fifth door trim is the most preferred place for mounting and fixing a rear view camera (duplicate name “saber”). To remove the saber, you will need to unscrew six nuts using the key set to “8”. The process of performing sequential operations is as follows: we mark on the saber the area where the camera will be mounted, then we drill a hole of the required diameter and pull the wiring for the video device through it.
To route the wiring harness without drilling extra holes in the tailgate, you can use any of the six holes for the saber clip. To do this, lift the elastic band and move it to the side. We cut the plug in place. Then we install the door trim on the remaining 5 nuts. Now the wiring for the camera is ready.
The device itself is attached to the outside of the fifth door trim using 2 strong self-tapping screws. To connect the camera to the video playback device, we stretch the wiring around the cabin. There are two options here:
- hiding it under plastic sills and trim of the door pillars;
- laying under the roof lining of the car.
As a result, the wire should appear behind the radio. If the kit you purchased does not include a monitor, then you can connect the device to a regular standard radio with a multimedia function.
Many motorists install video devices for viewing the road situation to simplify parking in places with a large concentration of cars. The presence of a standard parking sensor complements the system and reserves elements when one of them fails. Installing a rear view camera on Kalina 2 is desirable, since it does not have any other standard parking system.
How to connect a rear view camera to a DVR
This question consists of two parts: direct installation of the rear view camera and its connection to the DVR.
Parking cameras come in mortise and overhead types. To install the mortise ones, you will need to drill the bumper. The invoices are fixed to the glass with Velcro, and on the bumper or trim - with Velcro and self-tapping screws.
An overhead rear view camera can be installed on the glass inside the passenger compartment or outside - above the license plate (Fig. 5). It is clear that the first option is not considered if the rear window does not have electric heating and a wiper. But another important drawback of this installation is that you will not see the road directly under the wheels. And this function is very useful when driving off-road in reverse.
Rice. 5 – Rear view camera installation options
As can be seen from the figure, laying the connection cable to the DVR when installed inside the cabin does not cause any particular difficulties. The situation is different with external fastening.
In this case you will need:
— remove the cover with the number plate illumination and mark the location where the camera is mounted;
- secure it with Velcro, and then make holes for the screws - with a drill or an awl;
— screw in the screws, then use a knife to cut a small recess for the wire along the lower edge of the trim and bring it out into the trunk.
The power is connected to the reversing lamp (the red wire is to the positive of the lamp), the video signal is to the corresponding connector (Fig. 6). Thus, when reverse gear is engaged, recording is automatically activated and the image from the rear camera is displayed on the screen.
Rice. 6 – Rear view camera connection diagram
Throughout the cabin, the wire is stretched from the mirror to the trunk under the trim lining or passed through a standard corrugation with wiring.
Conclusion
By and large, self-installation of a DVR with a rear view camera purchased in one kit should not cause much difficulty. But if you purchased a parking camera separately from a two-channel DVR and want to connect it specifically, it is better to contact a specialist.
The rear view camera is not included in the standard equipment of the Lada Granta Liftback; owners connect the equipment themselves. You can purchase the accessory in a car store, car market, or on the Internet. Wide range, gradation by price categories, technical characteristics.
Installation
Due to the fact that there is no standard view of Kalina 2, the camera is positioned depending on its type so that it shows the situation behind the car without distortion. On Kalina hatchback it is most often installed instead of one of the room lamps. To do this, remove the trim from the trunk door and dismantle the saber. It is secured with 6 nuts. Then remove one of the lights, having previously disconnected the live wires.
Before installing the video device unit, it is necessary to drill out the standard mounting points for the lampshade, since the element being installed has a collar on the holes for self-tapping screws. For fastening, strips of durable plastic are placed on the inside of the saber, which will serve as the basis for screwing in the screws.
In most cases, a video camera with a pin is mounted on a lining under the trunk lock. The hole should be drilled away from the center, otherwise the pin of the device will interfere with the locking. The overhead camera can be mounted in the middle, since there is no need to drill anything. The pin of the device together with the wires is installed in the hole and secured with a nut. The video cable is passed into the trunk through the hole for the wires of the room lamps.
After this, you can install the overlay in place and begin connecting the traffic camera to the monitor or to the standard multimedia system (MMS). The video device is installed in the same way on the Kalina station wagon.
How to choose a good camera. Review of prices from different manufacturers
| № | Article/name | Price, rub.) |
| 1. | Kalina, Kalina-2, Granta (liftback), Vesta, Priora |
*prices are current as of September 24, 2018.
Technical characteristics of the rear camera of the Grant Liftback:
The most popular gadgets are in the price category up to 1,500 rubles. Picture display quality, focusing, zoom level are at an average level. Of course, the image is grainy, pixels are visible, and the viewing angle is only 170 degrees.
The rear view camera on the Granta Liftback in the range of up to 3,000 rubles has improved characteristics, image output quality, and a viewing angle of 180°. Despite decent parameters, gadgets in this price category are beyond the means of most car owners.
Procedure for installing the rear camera on the Granta liftback
- We place the car on a flat area.
- Remove the rear door trim.
- Remove the driver's and passenger's door sills on the left side.
- We lay a block with wires from the center console to the rear door lid.
- We dismantle the saber - spoiler.
- We install the mount.
- We connect the wiring to the 2-DIMM radio.
The order may differ from the above. In the event that the owner does not want to display the image on the standard radio. In this case, use a folding monitor. The location of fixation is arbitrary.
Preparatory stage
- isolation;
- screwdrivers with different tips;
- plastic spatula for plastic;
- blocks with wires;
- adapter - ISO type connector.
Dismantling works
- remove the thresholds from the left driver and passenger doors;
- fold the back row of seats;
- remove the upper trim of the interior and luggage compartment;
- Unscrew the fasteners, remove the spoiler from the trunk lid.
Laying wires, power supply from the circuit
We lay the wiring from the central channel of the console to the trunk lid along the following route:
- location for fixing the standard radio,
- the lower part of the dashboard on the left side under the steering wheel,
- thresholds,
- rear door pillar,
- luggage compartment lid.
Connection to the power circuit from the positive cable of the reverse gear lamp. In the Lada Granta Liftback it is green and located in the luggage compartment on the right side. Powering is done by soldering; twisting is also permissible, provided that the connection point is well insulated.
Connecting wiring, installing standard casing
After installing the camera, connect the positive cable to the flashlight wiring. We place the block with wires in a corrugated material made of fire-resistant material, and fasten the casing.
From the back of the 2-DIMM radio, we connect to the miniISO connector:
- black wire: ground;
- red: 12V power supply from the reversing light.
The designations on the plug are: pin 16 and pin 19, respectively. For the standard MMC radio, no additional firmware is required. The screen automatically switches to camera mode when reverse gear is activated. We start the engine, activate “R” gear, an image appears on the screen of the standard rear view camera.
Camera selection
You can install any universal camera on the Lada Kalina. Due to the fact that there is no space for a standard video device on the car, most drivers select them based on their capabilities. Most often, video cameras are located in the place provided for installing the license plate light. The most suitable size is the stock camera for the Volkswagen Touareg. The device is equipped with a small lamp to illuminate the room. The difference in illumination will be visible, but there will be no reason for a traffic police officer to stop due to the lack of 1 lamp.
Reviews
| № | Positive |
| 1. | Vitaly, 41 years old: connected the camera to the standard radio, did not flash anything additional. In total, I spent half an hour. I bought a Chinese Viori – 264897PR. |
| 2. | Gennady, 33 years old: the picture when reversing is good, the distance is marked. In case of insufficient lighting, I used side mirrors for objectivity of data. |
| 3. | Sergey, 31 years old: I work as a taxi driver and spend a lot of time on the road. In order to deliver/pick up a client as quickly as possible, it is necessary to maneuver in the limited space of courtyard areas. The camera is an indispensable assistant. |
| 4. | Kirill, 39 years old: a friend recommended a Viori rear view camera - 264897PR. I installed it and have been using it for over a month, no complaints. |
| 5. | Maxim, 42 years old: received a gift from his son for his birthday, installed it on his own. The lighting is good and the viewing angle is sufficient. |
| Negative | |
| 1. | Victor, 38 years old: I didn’t like the image on the standard radio, so I bought an additional folding monitor and installed it on the dashboard. The quality is good, no graininess. |
| 2. | Dmitry, 29 years old: I bought a folding monitor along with a rear view camera, since the image on my original radio was poor. I've been using it for two months, no complaints. |
| 3. | Vasily, 27 years old: I bought a car with a built-in rear view camera. I didn’t like the image quality on the “native” screen. I bought a folding monitor at the store. |
Conclusion The standard screen displays the image from the rear view camera with a resolution of 800 x 600 pixels. Obviously, this is not a 1920 x 1080 HD format, but the picture is quite legible. Those wishing to improve output quality can additionally purchase a portable monitor for an additional fee.
1. Removed the trunk door trim. It is attached with new caps: first you need to pull out the cap, then take out the cap. Removed the plastic trim on the trunk door. 2. The cover has space for installing a camera. I cut a hole for the camera in this shape:
3. Mating connector for YAZAKI 7283–8853–30 (AX951) camera. My connector was already crimped with wires. Pass the 4 connector wires through the seal of the stock wiring harness. The wires are thick and difficult to thread through, but possible. I crimped the EL 2×02 M connector onto the camera wires that go inside. Pinout of the camera wires: red - camera power + black - camera power - yellow - video signal white - video signal - 4. The camera wire was wrapped with shaggy electrical tape, placed in holders, connected connector The connector was secured to the cover plate with hot glue.
5. Installed the cover in place 6. Crimped the mating connector EL 2×02 F. As a cable for the camera, I used a simple three-core cable with a cross-section of about 0.5 mm2, which I got from some equipment. The camera's negative power wire was connected to the thickest black wire in the trunk door harness. There will be 3 wires going to the MMC: power +, video signal, video signal -.
7. I wrapped the camera cable with shaggy electrical tape and pulled it along the standard harness in the trunk door on the left side, in a rubber corrugation and along the rear pillar in the trunk, tying it to the standard harness. Before doing this, I disassembled the trunk trim.
8. In parallel with the standard connector, I also installed the EL 1×03 M / EL 1×03 F connector. 9. Next, pull the cable to the MMC along the standard harness. At the rear left arch, the same video cable from the trailer connector is connected to it (I have a camera installed on the trailer), as well as a trailer connection signal wire. 10. By tying the cable to the standard harness, I pulled it along the left side to the rear passenger’s feet. Then under the feet of the rear passengers to the starboard side. Then along the right threshold to the A-pillar. It went up the rack behind the glove compartment along with the antenna cable. In a place where there was no standard harness, I secured the cables with black tape, in the factory style:
11. Behind the glove compartment, where the cables come out of the rack, I installed the EL 3×03 M / EL 3×03 F connector. 12. Then, together with the antenna cables, placing them in their own holders, I brought the cables into the space under the MMC behind the climate control unit.
Connection: 1. According to information from the Internet, the power supply for the standard camera is +6V. I took a car phone charger, which is a +12V to +5V converter. I disassembled the case, took out the board, soldered three wires to it and crimped it with heat shrink.
2. Because I have two cameras, so I need a device that switches cameras. I assembled a relay circuit.
The device automatically switches video input and supplies power to the trailer camera when the trailer plug is connected. And also, by pressing a button, it forcibly turns on the rear view camera on the car. There are 4 connectors on the board: Connector X3 - video cables from the cameras that I connected earlier. Connector X4 is a voltage converter +12V to +5V. Connector X1—connection to the MMC harness. Connector X2—connection of the rear view camera power button. 3. Connect to MMS. In the MMC harness, cut the green wire for the reverse signal. Both ends will go to the switch. We connect to the orange ACC wire and the black minus wire. Insert the crimped contacts into the blue MiniISO MMC block: 16 - video input -, 19 - video input signal. I bought contacts in China a long time ago. We form a harness of six wires.
4. Connecting the button. I had the button with the camera symbol in stock, but with a green backlight. I bought a heated rear window button with white backlight 8450100638 and changed the button. You can order a button with the desired symbol here. We form a harness of three wires from connector X2 of the switch to the button. Block on the button: 1 and 2 - contacts; A, C - minus; B - backlight; D - indicator. I took the minus and the backlight from the adjacent heated rear window button. 5. In MMC you need to activate the video input. This is done in the NewMenu settings.
I secured the switch and converter boards under the MMC.
Result - I installed a standard camera: advantages (compared to Chinese ones) - standard appearance and quality, wide viewing angle; minus - price (3800 rubles). But I didn’t regret it, I’ve suffered through it with shitty Chinese cameras before. — Made the connection for the trailer camera. It helps a lot, especially when with an awning. — I forced the camera to turn on. You can control the load and trailer. — Now I see the tow bar ball, I won’t poke the bumper into the trailer anymore.
Immediately after purchasing the car, it was very unusual to have such a view of the rear hemisphere as a liftback. You can't see anything! Then I immediately got the idea to put the camera back, but the standard radio does not have a screen, and besides, I also needed a DVR, so the choice fell on a mirror DVR - it’s 3 in 1 or 4 in 1, or just N in 1. I ordered it here : ru.aliexpress />I decided to take it straight away from GPS on Android. It arrived in a week.
And so, one fine evening, my friend and I got ready to install this whole miracle. The photographs will not reflect all the steps, but only what was captured in the process.
This mirror came with fasteners not only in the form of rubber bands, but also for replacement instead of the standard one. I decided to remove the standard mirror and install a new one. The kit included a bunch of different adapters for different types of mounting, so I think it will suit almost everyone.
Next, it was decided to place the rear view camera outside, since after driving around a bit with the camera mounted on the rear window, parking was still inconvenient.
So, I ran the wires according to the following diagram:
There are three wires in total from the recorder: power, rear view camera and GPS receiver.
The rear view camera wire was pulled from the passenger side. First, I hid the wire under the trim near the windshield, then through the front pillar and, bending the rubber seal, also hid it under the trim.
Then, at the middle pillar, the decorative plastic part can be easily removed and passed through it further.
But after I brought it to the rear row of passengers, I used wire to extend it further and threaded the wire through the trim and the rear pillar. Then you need to remove the decorative elements from the tailgate:
1. The element is simply removed from the clips by picking it up from the middle. 2. Unscrew 4 screws (2 of them are the shelf fastenings on the side). 3. Unscrew two more screws in the grooves under the “handles” for closing the trunk. I also had to unscrew the decorative trim at the seat belt attachment point for the middle passenger (circled in yellow) in order to get under the trim and thread the wire through the corrugation to the trunk door.
Well, the fun began when I started running the wire to the trunk door. The holes are small, it’s difficult for your fingers to get into them, but again, everything was done with the help of wire, although it took a lot of sweat.
At this point, the red wire that should be connected to the reverse lamp is almost gone, so I soldered another 2 meters of wire and put it on heat shrink.
Next, I tied the wire to the harness, which goes on the left and goes to the rear door lock and license plate light, and ran the wire to the reverse lamp under the trim and plastic to the left lamp. There I found a wire going to the reverse lamp (mine was green) and soldered it to it.
Then I removed the saber from the trunk door by unscrewing 5 or 6 bolts. I also connected the wire along with the wire going to the license plate light. Then I drilled a hole for the wire in the place that, as I understood, was intended for the camera - just to the left of the trunk door release button and secured the camera with two bolts. I didn’t “drown” it deep, but simply screwed it on:
After pulling, there was still a supply of wire left, which I twisted into a bundle and hid under the decorative trim. Thus, there is enough wire to spare, with the exception of the wire to turn on the camera when reversing, which had to be increased.
I pulled the power wire through the left pillar, removed the heater control panel and there it was soldered to the wires going to the cigarette lighter. The GPS antenna was pushed under the roof lining.
This is what the image from the rear view camera looks like:
But, if there is little lighting, then, of course, the image will be noisy. It will show well during the day or under street lighting at night. Even at night, headlights from behind moving cars still illuminate the camera.
The mirror itself is larger than the standard one; when the visors are lowered, they rest against it, but this is not critical, since the visors are lowered completely and there is no point in moving them further. By the way, during the day the reflection in the mirror is clearly visible through the image on the screen.
You can launch applications and display images from cameras in a floating window:
You can display two images:
You can install YouTube and watch videos on the go:
There is a navigator. True, when launching such applications, the recorder becomes “stupid”, takes a long time to load everything, searches for an address on the map or loads the video, but then it works fine. It feels like he doesn't have enough memory. You can install the application and track the movement of the car, display images from cameras directly on your smartphone, if the Internet allows, of course. You can see the route during the day, for example. But the main thing it was used for was monitoring the situation behind the car and assisting in parking, which the recorder does an excellent job of and now you feel more confident when backing up.
Connection
The wires from the camera are routed along the inside of the trunk door to the corrugation of the standard power supply harness for the lamps. You can stretch the cable using thin steel wire. Some drivers power the camera from the license plate lighting. This is not entirely convenient, since power will only be supplied when the lighting fixtures are turned on.
It is better to connect the camera to the reversing lights. When reverse gear is turned on, the video device will receive power automatically and transmit the image to the monitor. The length of the camera's power cable does not allow it to be connected to the flashlight, so it is necessary to extend the cable by 0.5 m.
Throughout the interior, wires can be laid on the floor or under the roof trim.
Many drivers prefer the first option, because a poorly secured cable under the roof can rattle when driving. The Kalina Lux package includes a standard MMC, which provides for the connection of video devices, including a rear-view camera. The radio is equipped with a mini ISO connector for connecting them. The plug is blue. The corresponding wires are connected to pins 16 (ground) and 19 (+12 V).
In order for the radio to automatically display an image when reverse gear is engaged, you need to download and install the special Cam On Off program. After activation, the MMC can be put in place. The camera is powered from any consumer that receives power after turning the key to the ACC position. This could be either the cigarette lighter or the interior light.
After testing, the dismantled elements are installed in place. It must be remembered that due to the tilt of the camera, the parking lines convey the distance to the obstacle with distortion. In reality, they show the distance to the asphalt. The true distance is determined empirically.
A properly installed and connected video system will provide the user with safety when parking a car.
Installation of a rear view camera of a luxury package! Here is the first idea and MY FIRST ARTICLE for refining my car. Installing a rear view camera to the standard radio with display. I decided to describe the installation process and the difficulties encountered. And so: I bought a camera in a license frame! In Ufa in the world of electronics on sale for 990 rubles. it allegedly cost 1,700 rubles. 1.3mr, very decent picture. The package already includes a long cable from the camera to the radio. Tulip tulip. Let's start the installation: 1) First you need to get to the back panel of the radio. In the luxury configuration, you first need to remove the climate control unit. It is held on by 6-8 clips, there are no bolts or screws. You need to pry it from the edge with a screwdriver, grab it, and pull it firmly towards you. (This is the most difficult thing that seemed to me) There is a fear of breaking the socket, but it is strong enough and you need to pull harder, starting from one side or corner.
2) After removing the control unit, remove the top panel-visor of the screen. It is also on clips and can be removed very easily. The panel on the glass side has three ears that fit into the main panel. 3) Unscrew the two bolts that hold the radio. 4) Unhook the antenna wire, otherwise the antenna wire is not long enough to pull out the radio. (It is NOT located in the radio! But under the glove compartment closer to the right passenger pillar.) 5) On the rear panel we see a blue green and yellow plug. We need a blue one, it’s called “mini ISO” (in luxury versions it’s already there, but if it’s not there, you can buy it at an electronics store) we take it out.
6) Into this plug you need to insert into the 16th and 19th cells the wires (soldered or pressed to metal things. Shown in the photo) coming from the camera 16th - minus (ground), this is the outer side of the tulip 19th - plus, internal 7) Install the program CAM ON OFF on the radio. To do this, download it, unpack it on your computer, throw the unpacked folder onto a flash drive, connect it to the radio, turn on the radio and long press on the “settings” screen, the insides of Windows Mobile will open. We go to “My Device”, find the flash drive and go in, then go to the folder with the program, launch the cab file. In the window that appears, click “ENABLE CAMERA”, then close all windows and click on the HOME shortcut on the desktop to return to the normal radio mode. You can download it here dfiles.ru/files/y3epinx5p thanks to them lada-kalina2.ru We connect our ready-made plug, put the radio in place, but without checking its functionality we don’t assemble everything to the end. 9) We will power the camera from any source for testing, I powered it from the interior lamp. Turn on the power of the camera, turn on the rear camera. And a picture should appear. If it appears, then you can put the entire panel back together 10) We lay the wires to the rear door. I laid on the seals on the top, on the passenger side and the plastic panels of the pillars. Everything is very easy and fast
11) Remove the rear door trim: Unscrew the two bolts on the handle, then remove the panel itself, it is held on by “hedgehogs” at the top and in the middle. And on the bottom of the ears. So you need to remove it from the top and pull it out to the top side. After removal, the hedgehogs will be almost dead, so new ones will be needed.
12) Install the camera where it is convenient for you, etc. You can pass the wires through by removing the license plate lights, etc., but I just drilled through the metal behind the license plate. I stretched wires from there and sealed everything so that moisture did not get in, etc.
13) my camera is powered from the rear license plate light, that is, the camera will only be supplied with power when the side lights or low beam are on. The camera will not work with DRLs, just a white screen will be displayed when reverse gear is engaged. 14) put everything back together and rejoice at the result. When you engage reverse speed, the music fades out and the picture from the camera automatically appears!
Installing a rear view camera on a car significantly improves traffic safety. This device can be installed as an addition to parking sensors (parking assistant) or separately. In any case, the rear video camera will greatly facilitate maneuvering, especially when parking.
How to choose a good camera. Review of prices from different manufacturers
| № | Article/name | Price, rub.) |
| 1. | Kalina, Kalina-2, Granta (liftback), Vesta, Priora (99009916) | from 3000 |
| 2. | Viori – 264897PR | from 2700 |
| 3. | Lada Granta Liftback LGR-01 | from 1400 |
| 4. | CAM-98645236 | —/— |
| 5. | LGR-112 | —/— |
| 6. | Folding monitor 4.3 MR-01 | from 2000 |
*prices are current as of September 24, 2018.
Technical characteristics of the rear camera of the Grant Liftback:
- Matrix type: CCD (photosensitive);
- Viewing angle: 170°;
- Resolution 800 x 600 pixels;
- Zoom level: 0.01 Lux;
- Aspect ratio: 4:3;
- Gradation: parking lines on the screen (0.5 / 1.0 / 1.5 meters);
- Moisture and dust protection: present, level IP 67;
- Brightness: 300;
- Recommended voltage for correct operation: 12V;
- Operating temperature range: - 25° - + 35°;
- Connection type: ISO connector, from the back of a 2-DIMM radio or a separate folding monitor.
The most popular gadgets are in the price category up to 1,500 rubles. Picture display quality, focusing, zoom level are at an average level. Of course, the image is grainy, pixels are visible, and the viewing angle is only 170 degrees.
The rear view camera on the Granta Liftback in the range of up to 3,000 rubles has improved characteristics, image output quality, and a viewing angle of 180°. Despite decent parameters, gadgets in this price category are beyond the means of most car owners.
Setting up standard MMS
No firmware required for the radio, you just need to activate the rear view camera
. To do this, download the program (To download files you need to log in to the site) and copy it to removable media (USB Flash).
- Go to the desktop (WinCE). On the radio screen, hold down the “Settings” button, then “Exit” and “Desktop”.
- Let's launch the program. how to connect a rear view camera to a TV Connecting a rear view camera Installation of the camera should provide a good overview, parking lot markings should be visible for convenience. Rear view camera Lada Warranty on the camera is an indispensable assistant for both. How to install a turbine on a Zhiguli? My device - USB disk - Folder with the program - Run the CamOnOff file.
- We allow you to use the camera. Click on the corresponding button. We close the program, it and the flash drive will no longer be needed.
By the way, the whole process is also shown in the video:
Checking the operation of the rear view camera
including reverse gear.
Let us remind you that some motorists prefer to use parking sensors instead of a camera.
The Volzhsky Automobile Plant does not practice installing a rear view camera on its cars, so this process is carried out by car owners. Today we will tell you how to install a rear view camera on a Lada Granta with your own hands. You will need: a rear view camera, a knitting needle (wire) for pulling wires, a Phillips screwdriver. The easiest way to install a rear view camera on a Grant is to attach it to the bumper with self-tapping screws above the license plate. It is not necessary to remove the bumper for this. To route the camera wiring into the trunk, you will need to remove the left license plate light, and then pull the wires through the rubber plug using a long knitting needle. You will only have to remove the bumper on the Lada Granta if you decide to install a rear view camera inside the bumper. This placement of the camera will be more reliable, but installation time will also increase.
Installation
Required:
- rear view camera (see section Cameras for Grants).
- mini ISO connector (blue block and tulip).
- several meters of wire.
Most often, the rear view camera is placed above the license plate (on an overlay called “saber”). This location is the most favorable from a viewing point of view; the camera is not noticeable and there is no need to remove the bumper. First, remove the trunk lid trim, and then the saber, which is held on by 6 M8 screws.
We determine the most suitable place for the camera and drill a hole there. We secure the accessory on the reverse side with a nut.
We route the wires from the camera into the trunk through standard corrugations.
It is more convenient to route the wiring to the front of the car under the rubber seal of the headliner. Then we drag it under the dashboard to the back of the radio. To remove the MMC, you will first need to dismantle the panel cladding.
Procedure for installing the rear camera on the Granta liftback
- We place the car on a flat area.
- Remove the rear door trim.
- Remove the driver's and passenger's door sills on the left side.
- We lay a block with wires from the center console to the rear door lid.
- We dismantle the saber - spoiler.
- We install the mount.
- We connect the wiring to the 2-DIMM radio.
The order may differ from the above. In the event that the owner does not want to display the image on the standard radio. In this case, use a folding monitor. The location of fixation is arbitrary.
Preparatory stage
- isolation;
- screwdrivers with different tips;
- plastic spatula for plastic;
- blocks with wires;
- adapter - ISO type connector.
Dismantling works
- remove the thresholds from the left driver and passenger doors;
- fold the back row of seats;
- remove the upper trim of the interior and luggage compartment;
- Unscrew the fasteners, remove the spoiler from the trunk lid.
Laying wires, power supply from the circuit
We lay the wiring from the central channel of the console to the trunk lid along the following route:
- location for fixing the standard radio,
- the lower part of the dashboard on the left side under the steering wheel,
- thresholds,
- rear door pillar,
- luggage compartment lid.
Connection to the power circuit from the positive cable of the reverse gear lamp. In the Lada Granta Liftback it is green and located in the luggage compartment on the right side. Powering is done by soldering; twisting is also permissible, provided that the connection point is well insulated.
How to install a rear view camera on a grant
Do-it-yourself wiring and connection of wires You can run wires into the cabin to the standard multimedia system either through the headliner or along the side door trims. To work with ceiling cladding, we recommend using special “spatulas” and filling the voids under the cladding with additional pieces of foam rubber for the cable. On the A-pillar, the wire can be connected to the antenna wire, then stretch it to the glove compartment area to the radio or standard multimedia. The central panel is attached to metal clips and can be removed quite simply. To do this, you need to insert a flat-head screwdriver into the hole on top of the radio and pry it off, then disconnect several clamps. After this, remove the temperature and air direction regulators and use a screwdriver to unclip the fasteners along the perimeter of the panel from top to bottom. It is most convenient to connect the camera power wires to the reversing light.
Installation
Due to the fact that there is no standard view of Kalina 2, the camera is positioned depending on its type so that it shows the situation behind the car without distortion. On Kalina hatchback it is most often installed instead of one of the room lamps. To do this, remove the trim from the trunk door and dismantle the saber. It is secured with 6 nuts. Then remove one of the lights, having previously disconnected the live wires.
Before installing the video device unit, it is necessary to drill out the standard mounting points for the lampshade, since the element being installed has a collar on the holes for self-tapping screws. For fastening, strips of durable plastic are placed on the inside of the saber, which will serve as the basis for screwing in the screws.
In most cases, a video camera with a pin is mounted on a lining under the trunk lock. The hole should be drilled away from the center, otherwise the pin of the device will interfere with the locking. The overhead camera can be mounted in the middle, since there is no need to drill anything. The pin of the device together with the wires is installed in the hole and secured with a nut. The video cable is passed into the trunk through the hole for the wires of the room lamps.
After this, you can install the overlay in place and begin connecting the traffic camera to the monitor or to the standard multimedia system (MMS). The video device is installed in the same way on the Kalina station wagon.
Connecting wiring, installing standard casing
After installing the camera, connect the positive cable to the flashlight wiring. We place the block with wires in a corrugated material made of fire-resistant material, and fasten the casing.
From the back of the 2-DIMM radio, we connect to the miniISO connector:
- black wire: ground;
- red: 12V power supply from the reversing light.
The designations on the plug are: pin 16 and pin 19, respectively. For the standard MMC radio, no additional firmware is required. The screen automatically switches to camera mode when reverse gear is activated. We start the engine, activate “R” gear, an image appears on the screen of the standard rear view camera.
Camera selection
You can install any universal camera on the Lada Kalina. Due to the fact that there is no space for a standard video device on the car, most drivers select them based on their capabilities. Most often, video cameras are located in the place provided for installing the license plate light. The most suitable size is the stock camera for the Volkswagen Touareg. The device is equipped with a small lamp to illuminate the room. The difference in illumination will be visible, but there will be no reason for a traffic police officer to stop due to the lack of 1 lamp.
They install rear view cameras on cars, located in the license plate frame. With this arrangement, the device is not protected by body elements from dirt and dust. The option of placing a video camera under the trunk lining (“saber”) is more acceptable, but for installation you will have to drill a hole. The device is almost invisible; it can only be seen close up.
Lada Granta - installing a rear view camera
Due to the fact that a 2-DIN Chinese radio was purchased, I was honored to install a rear view camera. The radio came with a rear view camera, which had to be mounted on the outside of the trunk door. I was too lazy to run “kilometers” of wires along the trunk lid, rear pillar, disassemble the ceiling, and the sides of the trunk, so, after surfing the Internet, I found a camera that fits into the bumper, like parking sensors (much closer to the reversing lights). Installation in the bumper is the same as when installing parking sensors, instructions are here. A cutter of suitable size is included in the kit. The liftback has two reverse lights, so I connected the camera to the second one (the parking sensors are connected to the first one). The cameras came with wires. Connection diagram:
connection diagram
Connector P2 – red wire to + reverse lamps, black – ground.
The signal wire from the camera to the radio (which has tulip connectors) has another additional red wire P3. This is the power supply for the radio to output images from the camera. We connect one end to the + of the reverse light, the other to pin 9 of the radio connector (red dot on the ISO connector of the radio). Since birth, I had audio equipment in my car, but this wire was not in the block. I pulled the wiring out of the block that came with the radio and inserted it into the ISO block of the car. The wire was thrown under the carpet, the tulip is connected to the CAMIN connector on the radio.
connection
This is what happened on the screen
inside
This is what it looks like from the outside
outside
outside2
The rear view camera automatically turns on when you engage reverse gear, and also turns off automatically. If music or navigation is turned on, it turns off, then, when the camera is turned off, it turns on accordingly. An unpleasant feature is that at night, when driving in a narrow space, you still need to look in the mirrors; the glowing radio screen from the camera on is blinding. I found a solution: first turn on the radio or music, while the music is running, forcefully turn off the screen with the button in the upper right corner (the radio has a function that switches to day or night brightness (there is almost no difference between them) or turns off the screen), turn on reverse - image with The cameras are not displayed and you can safely move along the mirrors. I don’t know yet how quickly the camera will get dirty in this location, but I think wiping the camera is not a big problem. But the camera is positioned exactly in the center of the car and the image is not shifted anywhere.
Installing a rear view camera
for Lada Granta, Kalina, Priora and Vesta
It's hard to imagine a modern car without a rear view camera. Not much help for people who are looking for how to install a rear view camera on. AvtoVAZ understands this, which is why it equips the “luxury” version of the Lada Vesta with such an accessory. The following describes how to install a rear view camera on a Granta liftback and connect it to the standard radio (MMC), but similar instructions are also suitable for other Lada cars.
Connection
The wires from the camera are routed along the inside of the trunk door to the corrugation of the standard power supply harness for the lamps. You can stretch the cable using thin steel wire. Some drivers power the camera from the license plate lighting. This is not entirely convenient, since power will only be supplied when the lighting fixtures are turned on.
It is better to connect the camera to the reversing lights. When reverse gear is turned on, the video device will receive power automatically and transmit the image to the monitor. The length of the camera's power cable does not allow it to be connected to the flashlight, so it is necessary to extend the cable by 0.5 m.
Throughout the interior, wires can be laid on the floor or under the roof trim.
Many drivers prefer the first option, because a poorly secured cable under the roof can rattle when driving. The Kalina Lux package includes a standard MMC, which provides for the connection of video devices, including a rear-view camera. The radio is equipped with a mini ISO connector for connecting them. The plug is blue. The corresponding wires are connected to pins 16 (ground) and 19 (+12 V).
In order for the radio to automatically display an image when reverse gear is engaged, you need to download and install the special Cam On Off program. After activation, the MMC can be put in place. The camera is powered from any consumer that receives power after turning the key to the ACC position. This could be either the cigarette lighter or the interior light.
After testing, the dismantled elements are installed in place. It must be remembered that due to the tilt of the camera, the parking lines convey the distance to the obstacle with distortion. In reality, they show the distance to the asphalt. The true distance is determined empirically.
A properly installed and connected video system will provide the user with safety when parking a car.
Source
Reviews
| № | Positive |
| 1. | Vitaly, 41 years old: connected the camera to the standard radio, did not flash anything additional. In total, I spent half an hour. I bought a Chinese Viori – 264897PR. |
| 2. | Gennady, 33 years old: the picture when reversing is good, the distance is marked. In case of insufficient lighting, I used side mirrors for objectivity of data. |
| 3. | Sergey, 31 years old: I work as a taxi driver and spend a lot of time on the road. In order to deliver/pick up a client as quickly as possible, it is necessary to maneuver in the limited space of courtyard areas. The camera is an indispensable assistant. |
| 4. | Kirill, 39 years old: a friend recommended a Viori rear view camera - 264897PR. I installed it and have been using it for over a month, no complaints. |
| 5. | Maxim, 42 years old: received a gift from his son for his birthday, installed it on his own. The lighting is good and the viewing angle is sufficient. |
| Negative | |
| 1. | Victor, 38 years old: I didn’t like the image on the standard radio, so I bought an additional folding monitor and installed it on the dashboard. The quality is good, no graininess. |
| 2. | Dmitry, 29 years old: I bought a folding monitor along with a rear view camera, since the image on my original radio was poor. I've been using it for two months, no complaints. |
| 3. | Vasily, 27 years old: I bought a car with a built-in rear view camera. I didn’t like the image quality on the “native” screen. I bought a folding monitor at the store. |
Conclusion The standard screen displays the image from the rear view camera with a resolution of 800 x 600 pixels. Obviously, this is not a 1920 x 1080 HD format, but the picture is quite legible. Those wishing to improve output quality can additionally purchase a portable monitor for an additional fee.
Installing a rear view camera on a grant
If music or navigation is turned on, it turns off, then, when the camera is turned off, it turns on. An unpleasant feature is that at night, when driving in a narrow space, you still need to look in the mirrors; the glowing screen of the radio, from the turned on camera, is blinding. I found a solution: first turn on the radio or music, while the music is running, forcefully turn off the screen with the button in the upper right corner (the radio has a function that switches to day or night brightness (there is almost no difference between them) or turns off the screen), turn on reverse - image with The camera is not displayed and you can safely move along the mirrors. I don’t know yet how quickly the camera will get dirty in this location, but I think wiping the camera is not a big problem. But the camera is located exactly in the center of the car and the image is not shifted anywhere.
