Throttle position sensor on a Priora: why the speed fluctuates and the car accelerates poorly

Modern cars are controlled and controlled by an on-board computer. The Lada Priora model line was no exception, the central control device of which is the ECU (electronic control unit). When controlling the engine from a computer, the latter needs to receive the most up-to-date information from numerous sensors located in the engine compartment and other places of the car. One of these important elements is the throttle position sensor or Priora TPS.

The importance of this element is due to its purpose - calculating the position of the damper at the current time.

When you press the gas pedal (connected to the throttle assembly using a special cable), the throttle opens exactly as much as you apply pressure. At the same time, the amount of fuel supplied to the cylinders also depends on the degree of pressure. In order for the ECU to calculate the amount of gasoline to supply, it queries the TPS, which records the required data.

About TPS and its purpose

From the name it becomes clear that this device is responsible for the position of the throttle valve. In turn, the throttle valve is a bypass valve located between the air duct and the intake manifold. Air enters through this valve, which is mixed with gasoline and supplied directly to the combustion chambers. The damper drive mechanism is connected to the accelerator pedal via a metal cable. Pressing the gas pedal causes the damper to deflect to the appropriate angle, which is necessary for the intake (suction) of the required amount of air.

Now let's return to the throttle position sensor on the Priora, which is an electrical device that transmits a signal to the computer about the amount of throttle opening. And based on such important information, the controller makes the appropriate decision on dosing the mixture of gasoline and air. If the PDZ sensor fails, the first thing that appears on the instrument panel is the Check Engine indicator. However, with such a breakdown, the engine will function, but only in emergency mode, that is, when the preparation of fuel assemblies and the ignition timing will occur at average values, which will lead to increased fuel consumption.

This is interesting! It is important to understand that the sensor can not only fail, but also begin to give incorrect readings if its elements wear out. In this case, the normal operation of the engine will be disrupted, since depending on the deviations, either the mixture becomes richer or becomes leaner. And, in addition, due to incorrect information received by the ECU from the TPS, incomplete combustion of the fuel assemblies will occur, which will lead to an increase in the emission of harmful substances.

Throttle valve in pre-start position

The controller's task is to control the position of the throttle valve through an electric drive, which is set by pressing the accelerator pedal. TPS is needed just so that the controller can monitor the current position of the throttle valve.

When the ignition is turned on in the car, the damper is set by the controller to the pre-start position. At this moment, the degree of opening determines what temperature the liquid in the cooling system has. When the throttle valve is in the pre-start position, the output signal on the sensors from the first terminal should be about 0.39-0.52V , and from the second - 2.78-2.91V .

Types of TPS on Priora

Why do Priora car owners need to read this section, which describes the types of TPS sensors. Indeed, if you suspect a malfunction of this sensor, it is more important to first check it, and if the result is positive, replace it. All this is correct, but you need to know the types of TPS in order to choose the optimal device option for your car when replacing, which will not only last a long time, but also ensure more efficient and high-performance operation.

That is why there are two types of throttle position sensors. They have corresponding names, and differ in design, as well as principle of operation. In fact, you will learn about them further:

  1. Film-resistor (or resistive) TPS - it is also called a contact or mechanical device, which has a simple design and functions by changing the resistance. It consists of resistive tracks and a movable slider, which is connected directly to the throttle valve axis. Moving the slider along the track causes a change in resistance, which causes a voltage drop in the circuit. It is based on the change in voltage that the ECU understands what position the damper is in. In the design of Priora cars, sensors of the film-resistive type are most often installed from the factory, which are characterized by their low cost. Such a sensor has three contacts, one of which is a stabilized voltage of 5V, the second is ground, and the third is a signal contact, from which readings are taken and sent to the ECU.

  2. A non-contact sensor or magnetoresistive sensor is a potentiometric device that consists of a permanent magnet that changes its position depending on the angle of rotation of the damper. Such sensors are more advanced and accurate, and are also characterized by a longer service life, which is due to the absence of contact elements. Moreover, their price is higher than the cost of resistive devices (about 2 times).

Having an idea of ​​what types of TPS there are, you should consider the features of their functioning, which will be useful when carrying out test manipulations.

Verification technology

To check the sensor, you first need to determine whether it is direct or reverse. So, on Daewoo Lanos cars, almost the same sensor is installed as on VAZs, only they work in different directions. That is, in the closed position of the damper it can produce 5 volts, or maybe 0.5 if the graphite contact tracks are turned in the other direction. Be that as it may, to check the sensor you need a multimeter and a couple of minutes of free time.

When connecting a multimeter to the sensor, it should show the minimum or maximum voltage, depending on the engine, and when rotating the throttle, change the voltage value smoothly and without jerking. If there is even the slightest dip in the readings in any range, the contact tracks have worn out and such a sensor must be replaced. That's all you need to know so that the throttle position sensor does not ruin our lives. Happy travels to everyone!

The principle of operation of the TPS on Priora

It is important to know how throttle position sensors work in order to decide on the appropriate option for your vehicle. Initially, we will pay attention to common models of film-resistive devices. They are called film because there is a track on the film coating along which the slider moves. Such a sensor consists of the following structural elements:

  • plastic case;
  • resistive track;
  • a moving part in the form of a slider moving along the surface of the track.

Now, in detail about the operating principle of such an important product, which is most often used on Priora cars. A constant voltage of 5V is supplied to the track (when the ignition is turned on). The second end of the track is connected to the vehicle ground. The circuit is closed. The third contact is in the corresponding position and is connected to the throttle shaft. An insignificant voltage value of 0.55V is recorded at its output. When the gas pedal is pressed, the damper deflects, and with it the slider moves, during which the resistance of the circuit changes.

When the damper opens, the resistance increases (from 1 to 3 kOhm), which means the voltage at the output of the signal contact increases from 0.55 to 4.5 Volts. By changing the voltage value, the ECU understands the specific position of the throttle valve. Based on this value, as well as data from the mass air flow sensor, the control unit calculates the required amount of oxygen to prepare the optimal composition of the fuel assembly.

Over time, a mechanical sensor begins to show incorrect data, which often occurs due to abrasion of the contact layer on the tracks or slider. If such a part is unsuitable, it cannot be repaired and must be replaced.

Now let's look at the operating features of a more advanced sensor, which has not only a different design, but also a different operating principle.

They are also installed from the factory on Prioras. The operation of a magnetoresistive type TPS is based on the well-known Hall effect.

Thanks to this effect, the sensor has lost rubbing parts, which means its service life has increased. Instead of a contact plate with tracks, this sensor uses a permanent magnet. The case also contains an integrated board, which operates on the Hall effect principle. The microcircuit records changes in the magnetic field when the position of the permanent magnet, moving along with the damper, changes. The changing flow helps induce electrical impulses that arrive at the ECU.


Operating principle of a contactless sensor

The ECU receives similar impulses as in contact sensors, which indicates the most important thing - the possibility of their replacement with each other. This is very important, since many believe that contact-type TPS cannot be replaced with non-contact ones.

Malfunctions and replacement of the throttle position sensor Lada Priora


The degree of importance of every part of the car, be it an expensive steering mechanism or a cheap throttle position sensor of a Priora car, is difficult to overestimate, because the operation of the entire mechanism depends on the coordinated work of the parts.

TPS functions

The throttle valve is an element included in the engine intake system. Let us immediately note that the design of the throttle assembly is the same for both the 8-valve engine and the 16-valve engine. The meaning of its activity is to regulate the air entering the engine.

The throttle position sensor transmits information to the manifold about the current state of the bypass valve. There are two types of sensors - magnetic (non-contact) and film.

Its design is similar to an air valve, in which, when open, the system pressure and atmospheric pressure are identical; when closed, the pressure becomes close to vacuum.

The sensor includes a variable and constant resistor with a resistance of up to 8 ohms. The output voltage changes depending on how the damper is positioned. The system has control, thanks to which the fuel supply is regulated.

When the sensor is faulty and the readings are distorted, the fuel supply is disrupted, engine operation is disrupted, and in some cases the engine fails.

In addition, a working sensor will protect the gearbox and ignition switch.

What can cause sensor failure?


There is nothing eternal in this world.
Usually the TPS fails for natural reasons; the base along which the slide moves is simply worn out. Sometimes incorrect operation of the sensor is caused by the fact that the movable core fails. And damage to one of the tips entails the appearance of a number of scuffs, which can cause damage to the remaining parts. Ultimately, this can cause reduced or no contact between the slider and the resistive layer. Signs of a car going into emergency mode:

  • if at the moment of idling the revolutions “float”;
  • if the engine stops when the pedal is abruptly released;
  • if the speed hangs in the same range even when switching to neutral gear;
  • if the Check engine light on the dashboard comes on.

Why is there an exclamation mark on the Priora dashboard?

How to check the throttle


Checking the throttle is a simple process.
It is enough to have a multimeter or just a voltmeter. Adjustment can take place in your garage. To do this, the corrugated tube responsible for the air supply is disconnected, thoroughly washed with alcohol and wiped with a soft cloth. The same procedure is done with the intake manifold and the damper itself. Inspect everything carefully. If there is no mechanical damage, the sensor is adjusted. Use a wrench to loosen the screws. The damper rises and drops sharply until it stops; If you don't hear the impact, you need to repeat it again.

The screws are loosened until the product finishes “biting.” And only after that the fasteners are fixed with nuts. Then the TPS bolts are unscrewed and the housing is rotated, the sensor is set so that the voltage changes only when the damper is opened.

Everything returns to its place, the bolts are tightened, the adjustment is complete.

Which sensor is better - non-contact or film?

If the sensor breaks down, it is best to buy a new one. The main thing is to be able to make the right decision. You must choose a quality product and try not to be seduced by cheap Chinese counterfeits. In addition, it is better to buy a contactless sensor; it is more reliable than a film sensor and is inexpensive.

Having repaired or purchased a high-quality TPS, you can use your car for several more years, forgetting about this problem.

Common types of TPS failures

If a car has a film-resistive damper position sensor, its malfunctions are often associated with wear of the moving contact or fixed track.

During operation, the possibility of oxidation of the contacts, damage to the cores or insulation of the power wires is also not excluded. Over time, the elasticity of the spring is lost, which ultimately leads to its sticking.

Not only contact, but also non-contact sensors fail, but their service life is much longer, and they do not have the feature of supplying incorrect data.

If the contactless TPS fails, then it simply stops sending readings to the ECU, as a result of which the “CHECK” engine error will certainly be displayed.

This is interesting! The cause of failure of contactless sensors is a power outage or the occurrence of a short circuit current. Such devices, like film-resistive ones, cannot be repaired, so they need to be replaced.

Signs of a faulty TPS on a Priora: how to determine if the sensor is broken

Characteristic signs that the TPS on the Priora is failing are the following manifestations:

  • drop in engine power;
  • increased fuel consumption;
  • the occurrence of jerks when accelerating the car;
  • decrease in dynamics;
  • problematic engine starting (especially when cold);
  • possible engine detonation;
  • floating speed - if the sensor shows at idle that the damper is open, then the ECU will try to reduce the speed, which will lead to a process of changes;
  • delayed engine response to changes in throttle position.

The Check Engine indicator is displayed only when there is no signal from the TPS. The corresponding error codes are displayed on the Priora's on-board computer:

  1. P0122 - the signal from the TPS is low (i.e. weak).
  2. P0123 - the signal level from the TPS is high.

The signs described above only indicate that the problem is with the sensor circuit, so it remains to find out what exactly is faulty and how the breakdown can be repaired.

Replacing TPS with your own hands

The throttle position sensor on the Priora is located in the same place as on all other front-wheel drive VAZ cars. Directly on the throttle body, next to the idle air control. Symptoms of a TPS malfunction on a Priora can be different, and the main ones are listed below:

  1. unstable engine speed
  2. dips when moving
  3. jerks when accelerating
  4. no idle speed
  5. loss of engine power
  6. increased speed means the impossibility of engine braking

If your Priora has at least one of the above symptoms, then it is worth paying attention to the throttle position sensor. Fortunately, you can replace it with your own hands without any problems, and you will need the following tool for this:

  • Phillips screwdriver
  • Magnetic handle

Features of checking contact and non-contact TPS on Priora: pinout

If the corresponding signs of a malfunction of the TPS on the Priora appear, it would not hurt to check the product to make sure that the sensor has actually failed and that the wire has not been damaged or the contacts in the power supply have oxidized. To do this, you will need to know the TPS pinout, which is presented in the diagram below.

The easiest way to check is to use a multimeter. The detailed process for checking the Priora TPS is described below:

  1. Checking the serviceability of the supply wires. Disconnect the power supply from the sensor. Connect the multimeter probes to pins A and B, then turn on the ignition and check the voltage. The supply voltage should be 4.8-5.2V. If the value differs from the specified value (usually it is lower), then you should look for the cause in a wire that has a short to ground.

  2. Next, we proceed to check the contact sensor. The best way to check it is to measure the resistance between contacts A and C, that is, the signal and positive contacts. It is recommended to perform the test on a removed sensor. We connect the probes to the corresponding terminals and measure the resistance in kOhms. It should be in the range from 1 to 3 kOhm. When changing the position of the slider, the resistance should increase, and very smoothly without sudden jumps. If a different picture is observed, then the TPS needs to be replaced.

  3. Another test method (suitable for both contact and non-contact devices), which does not require removing the sensor, is to measure the voltage at the signal contact. However, it is recommended to implement it in exceptional cases, since it involves violating the integrity of the contacts of the sensor chip. It is carried out as follows: using pins, you need to attach the probes of the multimeter to the back side of the chip. You need to connect to terminals B and C, that is, signal and ground. After connecting, you need to turn on the ignition and, without starting the engine, change the position of the damper. If the voltage smoothly increases to 5V when the damper is opened to maximum, it means the part is working properly. If sudden changes (jumps) occur in the contact-type TPS, the product must be replaced. If the non-contact TPS is faulty, then its voltage will not change or will change, but in a low range.

Below is a video that shows in detail the process of checking the mechanical TPS.

Having confirmed that the throttle position sensor on the Priora is faulty, it should be replaced. Do not attempt to disassemble or repair it, as it is not repairable.

This is interesting! You can check the health of the sensor using a Bluetooth scanner connected to the OBD2 connector, as well as a special application on your smartphone.

If the BC displays a low signal error from the sensor, you need to check the power wires, since most likely the insulation has been damaged. If the signal level is high, then the fault is probably in the sensor itself.

Cost and articles

There are many different sensors on the market. They all depend on the manufacturer; the more famous the manufacturer, the more expensive the sensor itself is, accordingly. Below is a table with articles and prices for TPS for Lada Priora.

Manufacturervendor codePrice, (rubles)
RICOR2112-1148200400
StarVolt21120114820000390
ERA550485200

Where is TPS installed on Priora: location

You can make a mistake with the oil or speed sensor, but not knowing the location of the TPS on the Priora is unforgivable. If you have minimal knowledge of the structure of a car and know what a throttle valve is, then you will certainly be able to find the sensor responsible for its position.

The TPS on the Priora is located next to the throttle valve, but it is important not to confuse this product with the idle air control, since it is located nearby. The photo above shows the location, as well as the appearance of the TPS on the Priora.

Knowing its location, it will not be difficult to dismantle it for a detailed inspection or replacement.

Sensor repair manual

How to replace and repair the throttle sensor? Before starting the process, it is necessary to de-energize the vehicle's on-board network; to do this, disconnect the battery.

Further actions are carried out in the following sequence:

  1. Open the hood and find the regulator, as we already reported, it is located on the throttle assembly. You need to disconnect the connector from it. To do this, the mount itself must be moved up, as shown in the photo.
  2. Next, using a Phillips-head screwdriver, you need to unscrew the two bolts that secure the controller to the assembly. Be careful not to lose these bolts.
  3. After the bolts are unscrewed, the sensor must be removed.
  4. When the regulator is removed, pay attention to where it fits. Here you can see a special foam pad; it must be left intact. Carefully inspect the gasket - if it shows signs of damage, it is better to replace it.
  5. If you decide to repair the device yourself, then you need to carefully inspect the part for damage. Measure the width of the shaft, this figure should be 5 mm. If this indicator is different, then it will not be possible to change the gap; it will need to be completely replaced. It is quite possible that to ensure normal operation of the power unit, you will also have to clean the throttle itself. After all, if dirt has accumulated on the axis of the unit, the controller will have difficulty moving.
  6. As for further installation, there is nothing complicated in this matter either. Installation is carried out in the reverse order; this task should not cause difficulties.

Adjustment, calibration and configuration of TPS on Priora

The need to adjust the damper position sensor arises not only when installing a new device, but also when removing a standard product to check it. What is sensor calibration or adjustment? This is the process that ensures the correct functioning of the device. When the throttle valve is closed, the signal from the sensor should be supplied at a minimum value, and when it is fully open to 90 degrees, the voltage value should be maximum. If, when the damper is closed, the voltage on the signal wire is, for example, 1V, although it should be about 0.5V, then the ECU will consider that it is open and will incorrectly adjust the composition of the fuel assembly.

When removing the standard sensor, you must note its position on the throttle assembly, otherwise you will need to carry out the adjustment process. Few people know about this, which ultimately leads to incorrect functioning of the engine. What is the process of calibrating TPS on Priora, we will consider further.

  1. Initially, it should be noted that sensors can be installed on Prioras from the factory without adjustment, and therefore the engine may not operate correctly. That is why it will be useful to carry out the setup process if signs of incorrect operation of the TPS are detected.
  2. The procedure can be performed in two ways. The first requires the use of diagnostic equipment (PC with software and OBDII connecting cable). You can also use the Bluetooth module and the Open Diag application. The second method is based on using a multimeter. First, let's look at the setup procedure using diagnostic equipment.
  3. Initially, install the TPS, but do not tighten the mounting screws. Be sure to wear a power supply.
  4. Connect a PC with the software and run the program. In the application, go to the “Variables” tab, where you indicate the value of the signal from the PD sensor.
  5. We turn on the ignition and perform diagnostics. The left column indicates the throttle position as a percentage, and the right column indicates the output voltage (see photo below).

  6. When the throttle is closed, the value in the right column should be 0. To achieve this result, you need to move the sensor perpendicular to the throttle valve axis to the left or right. If you cannot set the value to 0, it means that you need to increase the diameter of the sensor mounting holes (bore them) using a needle file.

  7. It is important to enlarge the holes so as to be able to move the TPS relative to the damper, which will allow its position to be adjusted. The photo below shows the areas on the DPDZ that need to be filed off with a file.

  8. After this, we repeat the procedure and ensure that the program shows a value of 0 when the damper is closed. In the left column, the output signal voltage should be about 0.55V. We focus, first of all, on the percentage value, which should be equal to zero when the damper is closed. It will not be superfluous to inspect the condition of the damper, since a large amount of carbon deposits on it can cause incorrect adjustments.

  9. After this, open the damper to maximum and record the value in the application. The left column should display 100%. This indicates that the sensor is installed correctly, and regarding the position of the damper, it will transmit correct and accurate data to the ECU. We fix the sensor mounting screws and make sure that the product does not move to the side when tightening. Otherwise, repeat the check after tightening the screws.

This procedure is correct and allows you to adjust the position of the sensor with high efficiency and accuracy. If you do not have a PC, a connecting cable and an application, then the setup can be done using a multimeter. The process is almost identical, you just need to focus on the output voltage from the sensor:

  1. To do this, the sensor should also be installed in place, but do not tighten it with screws.
  2. Connect the multimeter probes to the terminals of the sensor chips B and C, using pins so as not to damage the integrity of the wire insulation.
  3. Set the multimeter to DC voltage measurement mode of at least 5V.
  4. Turn on the ignition and record the value with the throttle valve closed. The output signal should be around 0.556-0.557V. If the value is greater, it is necessary to increase the diameter of the mounting holes in the sensor and rotate it so as to obtain a value of 0.55V with the damper completely closed.

  5. Having achieved this indicator, you should open the damper to the maximum and record the voltage value. It should be 4.56-4.57V.

This completes the process of setting up the TPS. And you can verify by the sound of the motor that the sensor is functioning correctly.

After these steps, be sure to reset the controller. This can be done either by removing the negative terminal from the battery or by turning the ignition on and off several times.

This completes the process of setting up the TPS on the Priora. It remains to consider the question of what type of sensor is best installed on the car.

Throttle valve at rest

If within 15 seconds from the moment the ignition is turned on, the engine is not started and the accelerator pedal remains at rest, the controller will stop the supply of power to the electric throttle drive, as a result of which the damper will move to an almost closed position (no more than 7% opening). In this state, the output signal power of the first sensor will be 0.5-0.6V , and the second - 2.7-2.8V .

If the engine and accelerator remain at rest for the next 15 seconds, the throttle will automatically enter test mode. This means that it will move to the zero position until it is completely closed and then moved to the pre-start position, after which the electric throttle drive will be completely de-energized until the next ignition is turned on.

If a problem is detected in the sensor circuit, the controller completely stops supplying voltage to the throttle actuator, while simultaneously storing the error code in memory and displaying it on the dashboard. In this case, the throttle valve is always set to 6-7% opening

.

Regardless of what position the throttle valve is in, the output signals from both sensors should add up to 3.3V . The maximum permissible deviation is 0.1V .

Rating
( 1 rating, average 5 out of 5 )
Did you like the article? Share with friends:
For any suggestions regarding the site: [email protected]
Для любых предложений по сайту: [email protected]