Jaguar alarm system review: instructions for use, installation and autostart setup

03/03/2022 2,646 Alarms

Author: Victor

The instructions for using the Jaguar alarm system with auto start indicate that installation of these systems is only possible on cars with a 12-volt on-board network. Accordingly, on vehicles with a voltage of 9 V or 24 V, the use of the remote engine start function will not be possible.

[Hide]

Description and technical specifications

You can use Jaguar “alarms” of the EZ and TEZ lines on cars with an automatic transmission or a manual one. All modern models of security systems allow operation in alert mode. This means that the user can learn about the vehicle’s security status from the indicators on the key fob display. Jaguar anti-theft systems allow you to start the engine remotely, by command from the remote control or at a certain time configured by the user.

The service manuals for alarms indicate the following technical characteristics:

• radio frequency channels of 433.92 or 868 MHz are used to transmit signals between the control unit and the communicator;
• the range of action of the control panel when sending pulses is 600-1200 meters;
• operating range of the additional key fob is 15 m;
• protection of all power lines that need to be installed and connected to the microprocessor is carried out by safety devices of 7.5-30 A;
• the choice of rating depends on the type of equipment being protected and is indicated in the technical manual;
• when the security mode is on, the alarm current consumption should be no more than 15 mA;
• activation of the protection function is possible with a delay of 5, 30 or 45 seconds after sending the signal;
• vehicle security is provided through power outputs of the ignition system, door limit switches, hood, and additional controllers;
• the total number of communicators that can be connected and configured to work with alarm systems is 3-4 pcs. depending on the model;
• The main key fobs are powered by 1.5 volt AAA batteries, and 6V CR2025 batteries for additional key fobs;
• The anti-theft system can be controlled automatically or through the use of the car owner's call controller.

Equipment

List of items included in the delivery set:

1. The control unit is made in a black plastic case.
2. Service documentation, including electrical diagrams for connection, use, as well as recommendations for installation. The manual describes in detail all the features and provides steps for setting up the system.
3. The main communicator, equipped with an LCD display and equipped with a two-way communication option.
4. An additional key fob that is not equipped with a screen and has a shorter range.
5. A transceiver module equipped with a button to call the car owner from inside the car with a connected cable for connection. By clicking on it, a message about the need to approach the vehicle will be sent to the remote control with a display. The antenna module is equipped with a special sensor, which is used to determine the temperature conditions inside the car.
6. A siren belonging to the class of six-tone devices.
7. Two-level sensitivity and impact controller.
8. LED to indicate alarm status.
9. Valet service button.
10. Limit switch designed for mounting on the hood.
11. A set of cables and blocks for making connections.
12. Two power supplies for installation in communicators.
13. Stickers - one with the anti-theft system logo, the second - for attaching the transceiver module.
14. Warranty card.

The delivery set includes one limit switch; other devices for the doors and trunk are purchased separately.

Photo gallery

Jaguar alarm photo:

Anti-theft control unit

Jaguar EZ-B Scope of Delivery

Disassembled Jaguar alarm communicator

Basic signaling capabilities

List of features and functions of Jaguar anti-theft systems:

1. Option to turn on the security mode with or without sound and light accompanying signals. In the latter case, this is a silent protection function.
2. Protection of a vehicle from robbery, “Anti-robbery” option. The car's engine will automatically shut down during specific events. For example, if the owner is forced out of the car, the security system will determine this by signals from the controllers on the handbrake or brake pedal. The engine is blocked after a certain time, when the thief drives to a safe distance for the car owner.
3. Possibility of selecting alarm signals.
4. Availability of seven independent security zones. We are talking about all the car doors, trunk, hood and ignition system.
5. Using two-stage security disabling.
6. The presence of a driver warning function about unlocked locks.
7. Possibility of connecting the steering signal to the siren of the anti-theft system.
8. Automatic engine start upon command from the remote control, at a specified time or temperature. When the level of the latter drops to a critical level set by the user, the power unit is started remotely. Allowing the engine to automatically turn on and warm up during the night will help prevent it from freezing in the morning.
9. The presence of non-volatile memory of the control unit about events recorded by the alarm. If the microprocessor module is disconnected from the power supply, when it is further connected, information about the operations will remain.
10. Possibility of connecting additional digital relays to block the engine.
11. Indication of the power source discharge in the main remote control, as well as the voltage level in the vehicle’s on-board network. All information is displayed on the communicator screen.
12. Use dynamic encoding to protect signals.
13. Availability of energy saving mode. This helps prevent your device's battery from draining quickly.
14. Possibility of online programming of options.
15. The presence of a button lock function on the communicator.
16. Using a personal password to emergency disable the anti-theft system. The PIN code can be used to enter the alarm service mode.
17. Possibility of additional connection to the GPS tracker anti-theft system. This will allow you to determine the location of the vehicle.
18. Option to monitor the start of the power unit using signals coming from the tachometer or generator device.
19. Possibility of turning on the protection mode on a car with the engine running.
20. Availability of the “Hands Free” option. This function allows you to automatically turn the vehicle security on and off if the car owner moves away or approaches the car.
21. Ability to select the duration and number of door lock control signals.
22. The presence of a “Turbo timer” mode, which allows you to prevent rapid wear of engine structural elements. The turbine cooling time is user adjustable. The essence of its action is that after the ignition is turned off, the engine continues to idle for some time.
23. Function of automatic return to security mode if the alarm is accidentally turned off.
24. Warning the user with light signals about unlocked door locks.

User Alexander Bobrov, in his video review, briefly spoke about the capabilities and features of the Jaguar alarm using the example of the EZ-Four model.

Advantages and disadvantages

Main advantages:

• affordable price;
• extensive functionality;
• effective operation of the autostart option regardless of weather conditions.

Flaws:

1. Using dynamic code. Today this type of encoding is not relevant. Manufacturers of anti-theft systems use interactive signal coding as a more reliable protection option. It will be easier for the hijacker to “break” the “dynamics”.
2. The communicator comes in a weak case. The device may fail even with a slight fall, and constant use will lead to the buttons on the remote control sticking.

Equipment

The Jaguar package includes one limit switch, the remaining switches will have to be purchased separately.

Components included in the alarm kit:

1. The microprocessor module is the main device of the car alarm.
2. User's Guide to the management, use and maintenance of the alarm. If you carefully read the service manual, you can learn about additional useful functions.
3. The main console is equipped with a screen and has a two-way communication function.
4. Spare remote control. It has a shorter range and is not equipped with a display.
5. Transceiver equipped with a key to call the owner of the car. This device is equipped with a built-in temperature controller that allows you to measure its value inside the car. The transceiver comes with a wire and connector for connection.
6. Six-tone siren.
7. The impact controller belongs to the two-level class.
8. A diode light bulb that functions as a status indicator.
9. One limit switch for hood mounting.
10. A set of connectors and wires for connecting the signaling system.
11. Two batteries for installation in the main and spare transmitter. They differ in type from each other, so you won’t be able to confuse them during installation.
12. Two stickers - one with the Jaguar logo, the second is used to fix the antenna module.
13. Warranty card.

How to install?

In accordance with the instructions for using the Jaguar alarm system with auto start, the installation of the anti-theft system is carried out on a car with the battery disconnected. To do this, the user must first open the hood and disconnect the negative terminal from the clamp.

Installation rules

Installation Guide:

1. Before performing a task, the windows of the car are lowered. This will allow the user not to be locked in the car if the alarm is accidentally closed.
2. We recommend connecting all Jaguar elements without installing them on the car to check their functionality. The system is connected directly to the battery for testing.
3. The alarm control unit is being hidden mounted. It is recommended to place it behind the instrument panel to ensure a minimum length of wires. The unit can be installed behind the glove box or in the free space behind the car radio. The module should be placed on a flat surface with the connector facing down to prevent moisture from getting inside through the wires. To fix the device, double-sided tape, self-tapping screws or plastic ties are used, if the surface design allows.
4. The siren is being installed in the engine compartment. Installation should be carried out in a hidden place so that the horn of the device faces down. The wires from the siren should not hang down so that an attacker cannot gain access to them from under the bottom of the car. Do not place the device near sources of moisture or high temperatures as this may cause the device to melt.
5. A limit switch is installed on the hood. It must be placed in a place where there is no accumulation of moisture. When the hood is closed, there should be no access to the device. If you purchased additional “limit switches” for the doors and trunk, then they also need to be installed. To do this you will have to remove the plastic lining.
6. A transceiver module is installed on the inner surface of the windshield or rear window. Do not install the device near metal parts or electronic devices as this will reduce the range. Double-sided tape or glue is used to fix the antenna module.
7. The sensitivity sensor is installed in the central part of the vehicle. It can be placed on an iron partition that separates the car interior from the engine compartment. The device must be installed so that the user has access to its adjustment elements.
8. The service button is installed in a hidden manner, but in such a way that the consumer can reach it when sitting in the driver’s seat. You can install the device under the instrument cluster and hide it in one of the wiring harnesses. To disguise the button, you can wrap it with electrical tape of the standard color.
9. Laying of electrical circuits is carried out under the decorative cladding of the vehicle. Wires should not be laid in places where there are moving mechanisms. In addition, it is not recommended to lay cables near electronic devices and equipment. If it is necessary to extend conductors, all joints during soldering must be located in the vehicle interior. This will prevent them from oxidizing.

Layout of elements

Maps for connecting the anti-theft system are provided at the link:

When should you buy a Jaguar?

Here we will talk about one of the signaling models - this is the Jaguar EZ-Beta V2. Distributors have such equipment available at prices below 100 USD. It is recommended for purchase by all beginners and those who install alarm systems themselves. But if you need to implement a connection with autostart, make sure that there is no “15/2” contact in the ignition switch, which switches the current in the IGN2 circuit. When the key is in the START position, the test lamp on this contact does not indicate the presence of a “positive” potential.

Electrical circuits of the ignition switch

It is even more impossible to implement autostart if three ignition circuits are used (IGN1-IGN3). Unfortunately, the signaling devices of this model do not emulate contact “15/2” or “15/3”. Which is typical for almost all Jaguar alarms, if their cost does not exceed 150 USD. Installation on all domestic cars will be acceptable, but on foreign cars you need to check whether the IGN2 or IGN3 circuit is used.

User manual

You can use the alarm after installing power supplies in the communicators. To do this, remove the back cover of the remote control and install the batteries taking into account the polarity.

Controlling the system from a key fob

Key designations on the communicator:

Correspondence of buttons on the main and secondary remote control

To control the system, the combinations given in the table are used:

Designation of icons on the keychain

The key fob display shows 24 options necessary to control the alarm.

Description of indicators on the LCD display

Description of indicators on the remote control display:

1. Option to automatically start the motor at a user-specified time.
2. Remote engine start mode using a timer.
3. Automatic start of the power unit based on temperature level.
4. Indicator of the brake pedal being depressed or the handbrake not being tightened.
5. The anti-theft system service mode is enabled.
6. The "Turbo timer" option is activated.
7. Indicator of automatic activation of protective mode.
8. Engine immobilizer function.
9. The option to lock the buttons on the remote control is enabled.
10. Indication of battery charge of the communicator.
11. Symbol of triggered warning or alarm zones of the main or additional controllers.
12. Indication of engine or interior temperature level.
13. Anti-robbery mode is enabled.
14. Vehicle engine running indicator.
15. Icon of an additionally connected GPS module.
16. Symbol for bypassing the warning or alarm zone of the shock sensor.
17. Indication of the current time.
18. The countdown timer is activated.
19. The alarm is on.
20. Indication of the range of the key fob.
21. Symbol of open or closed door locks.
22. Indicator of activated security mode with or without accompanying audio signals.
23. The function of disabling the alarm using a personal password is enabled.
24. Manual transmission mode is activated.

Key fob programming

To bind a new communicator, perform the following steps:

1. The ignition in the car is turned on.
2. The Valet service key is pressed and held until the system plays four beeps.
3. To bind a new remote control, the owner simultaneously presses buttons 1 and 2. If an additional communicator is used, then you need to “click” on buttons 3 and 4. Successful programming will be indicated by 1 siren signal.
4. Point 3 is repeated for each key fob that is registered. The time interval between recording devices should be no more than five seconds, otherwise the alarm will leave the binding mode. The number of siren signals depends on the number of the programmed key fob.
5. The ignition in the car is turned off. Five signals from the car's headlights will indicate a successful exit from the binding mode.

The Jaguar alarm system allows you to record up to four communicators into the control unit’s memory. When programming new devices, you must also re-register the old ones, otherwise information about them will be deleted.

Security mode

Features of protective function control:

1. To turn on security with sound signals, use the first button; press it briefly. The vehicle's ignition must be turned off and all doors locked. When turned on, the display will show indicators in the form of a closed lock and a speaker. Disabling is done using the first button.
2. Silent security is activated by moving the cursor to the position of the corresponding indicator on the display. After selection, press button 2. Icons in the form of a lock and a crossed out speaker will appear on the screen. When disabling security, you must move the cursor to the position of the same indicator, and then press the second key.
3. Before turning on the vehicle protection with the engine running, the user lifts the parking brake lever. Button 1 is pressed and held until the car's headlights blink three times. An indicator in the form of smoke from a muffler will appear on the communicator screen, and the LED will light continuously. The key is then removed from the ignition and the engine should remain running. Over the next 30 seconds, the user should leave the car and press button 1, this will turn on the security.
4. To disable the protection of the machine with the engine running, briefly press the first button. To confirm, the alarm will sound a siren twice and blink its lights twice. The motor will continue to operate and stop after a time set by the user.

In the video, Alexander Shkurevskikh spoke about managing the Jaguar alarm system.

Emergency management

If there is no remote control, you can control the security mode using the service button:

1. The car's ignition is turned on.
2. The user “clicks” the emergency mode entry key eight times.
3. The ignition turns off. The alarm will sound once with the siren and car lights.
4. Within 20 seconds, the user must leave the car and lock all door locks with the key. The security will be activated automatically.
5. To disable the protection, the user opens the door locks, which will activate the alarm mode.
6. The key is inserted into the lock and the ignition is activated. There is no need to start the engine.
7. Within 20 seconds the service key must be pressed 4 times.
8. The ignition is turned off. The alarm deactivates the protection mode.

Setting up autorun

Before implementing the function, the car must be prepared:

1. With the engine running, the gearbox selector is set to the neutral speed position. The handbrake lever is lifted.
2. The ignition is turned off and the key is removed from the lock. The motor should remain in working order.
3. Over the next 30 seconds, the driver leaves the car and locks all doors, including the hood and luggage compartment. The motor will stop or run for a certain time if the Turbo Timer function is turned on.
4. To start the engine on command, press and hold key 1. When a melodic signal appears, you need to release the button and press control number 3.
5. The car's headlights will flash three times. If this happens, the engine has started successfully. As confirmation, an indicator in the form of smoke from the exhaust pipe will appear on the display.

By time

Timed triggering is done as follows:

1. The user must ensure that the current time on the device is set correctly.
2. The alarm is being set. After completing the task, an indicator in the form of a bell will appear on the screen.
3. The third key on the key fob is pressed. It is held until two signals are played - melodic and short. The button can then be released.
4. Using control 3, the cursor is positioned at the position of the icon labeled “Clock Start”.
5. The first button of the key fob is pressed, the option will be enabled. The lighting devices will blink and the communicator will play a melody. The corresponding indicator will light up on its screen.

By temperature

The temperature setting is done as follows:

1. Button number 3 is pressed and held. The remote control should play a double beep.
2. The control element is released. The icons on the bottom row of the communicator display will flash.
3. Using button 3, the cursor on the device display is moved to the position in the form of a thermometer. The temperature at which the car engine should start is selected.
4. After setting the parameters, press key 1. The vehicle's headlights should blink, and the thermometer indicator will light on the remote control display.

On the Sigmax69 channel they talked about setting the engine operating time during automatic start.

Additional options

Setting the current time on the communicator display is as follows:

1. Button 3 is pressed and held. The key fob should first emit one melodic, then a short and two long signals.
2. The key is released. The remote control will enter clock setting mode.
3. To increase parameters, use the first key, to decrease - the second. Quick changes in readings are possible by pressing and holding the buttons.
4. To go to the menu for changing minute values, use the third key. The steps to decrease or increase parameters are similar.
5. Exit from the clock programming menu is carried out by holding down key 3.

The alarm clock is set as follows:

1. Button 3 is pressed and held. The communicator should play several beeps.
2. The key is released.
3. Button 3 is pressed twice. An alarm indicator in the form of a bell will appear on the communicator screen.
4. The clock is being set. Increasing the readings is performed by the first key, decreasing - by the second.
5. To go to the menu for changing minutes, briefly press the third button. The steps to increase or decrease parameters are the same as in the case of a watch.
6. Activation and deactivation of the settings mode is performed by briefly pressing the third button. Then, using keys 1 or 2, the option is turned on or off. To leave the setup menu, the third button is pressed and held until a short beep appears.

Key Features

Main functions of Jaguar alarms:

1. Possibility of activating the protection mode with or without sound and light accompaniment.
2. The ability to notify the car owner about events recorded by the security system. The key fob with feedback displays data about activated security zones.
3. Protection against robbery, this function is called Anti-hijack. She is intelligent. The essence of its action is to block the motor when the car is forcibly seized. When criminals force the car owner out of the car, the alarm system can understand this by analyzing the operation of the sensors installed on the brake pedal and handbrake lever. After the car moves to a safe distance from the car owner, the engine lock will be activated.
4. The consumer can independently select the signal that is played when the alarm is activated.
5. Seven independent security zones provide more reliable protection.
6. Disabling the protection mode is carried out in two stages.
7. The ability to warn the car owner that he forgot to lock the doors before driving.
8. If necessary, you can connect the steering horn to the car siren.
9. Automatic start. This option will ensure the engine warms up in the cold season and will be useful for those who are constantly late. Now you don't have to waste time warming up the car.
10. The memory of the microprocessor module allows you to record information about events that occurred in the operation of the security complex. Even after disconnecting the battery, information about this will remain in the memory.
11. The consumer has the opportunity to additionally connect digital relays used to block the power unit.
12. The consumer has the option of additionally connecting a GPS beacon to the signaling system.

Download alarm installation and operation instructions in PDF format

You can read free service manuals on the use and installation of Jaguar anti-theft systems of different models using the following links:

Clarification for vehicles with manual transmission

You need to understand that the car needs to be prepared before starting the engine using autostart. However, we are talking only about cars with a manual transmission. And here's what the instructions say about this:

1. During half-cooking, the handbrake is first engaged. The engine must be running.
2. You need to remove the key from the lock - the engine should not stall;
3. In half a minute you need to leave the salon and close the doors.

When the last door is closed, the security mode can be turned on. This is exactly how the TEZ B system should be used.

This is how a car is prepared for autostart

An alarm from another brand, such as Starline, may work differently: between steps 1 and 2, you press a button. Jaguar systems do not provide such a method. By the way, the sequence discussed above is also used when turning on the turbo timer: if it is not followed, the engine will stall in step 2. The turbo timer option must also be enabled in the settings.

Possible faults

Malfunctions that can occur in the operation of Jaguar anti-theft systems:

1. The battery in the communicator is low. Such a malfunction will lead to a deterioration in the range of the alarm, as well as poor operation of functions. The user must check the operation of the power supply and replace it if necessary.
2. Communicator failure. If the device stops working as a result of a fall or mechanical damage, it will need to be disassembled and diagnosed. Damaged contacts and buttons can be re-soldered, but the procedure for changing the firmware is difficult to perform on your own. If the problem is the effect of moisture on the device, then you need to remove its board and dry it in a warm place. It is not allowed to use a stove or a household hair dryer to remove condensation.
3. Damage to wires. The areas of electrical circuits located in the protective corrugations between the doors and the body are most susceptible to wear. To search for damaged cables, you will need a tester; it can be used to ring power lines. The wires must be replaced with products with the same cross-section. For better protection, the cable can be wrapped with electrical tape.
4. Failure of limit switches. For this reason, the system may not close all doors. Most often, the contact on the wire through which the sensors are connected to the on-board network wears out. They may oxidize, then to solve the problem you will need to clean the pads.
5. Incorrect installation of the transceiver. Because of this, the signal quality will be poor. To fix the problem, the antenna module must be moved to another location.
6. Control unit malfunction. Software problems should be resolved by specialists, as firmware changes may be required. If the microprocessor module fails due to exposure to moisture, as is the case with the remote control, you need to remove the board from it and dry it. The contacts on the unit connector may be oxidized or clogged. To fix the problem, you will need to clean the pad.

Functions

The alarm system discussed in this review has the following functionality:

• silent activation of protective functions;
• “Anti-robbery” mode (the engine automatically stops in the event of a robbery on the vehicle, the blocking is activated a few seconds after an unauthorized start of the engine);
• use of an individual code to disable security functions;
• connecting the standard horn to the anti-theft system;
• remote engine start by issuing a command from the key fob or pre-setting parameters;
• saving user settings in non-volatile memory (when dismantling and then connecting the main unit, the selected settings are not lost);
• the possibility of introducing additional devices to block the power unit;
• indication of the charge of the remote control batteries;
• dynamic coding of sent signals;
• energy-saving mode that prevents the batteries in the control panel from discharging;
• locking key fob buttons;
• the ability to connect a GPS module used to determine the vehicle’s coordinates;
• assessment of the condition of the power unit, carried out by analyzing signals coming from the generator or tachometer;
• activation of the security mode when the engine is on;
• “Hands-free” (the option is aimed at automatically activating and disabling protection when the user approaches or moves away);
• remote control of door locks;
• turbo timer (the ability to select the turbine cooling time; when this function is turned on, the engine idles for some time);
• automatic resumption of security after an unplanned shutdown;
• door closing control.

Advantages and disadvantages

The anti-theft system has the following positive qualities:

• low price;
• expanded set of functions;
• correct operation of autostart at any temperature.

Negative characteristics of Jaguar car alarms include:

• insufficiently efficient signal coding method;
• poor build quality of the key fob (over time, the buttons begin to fail).

Video

On the Sigmax69 channel they talked about programming the buttons of the Jaguar alarm control key fob.

Do you have any questions? Specialists and readers of the AUTODVIG website will help you ask a question

Was this article helpful?

Thank you for your opinion!

The article was useful. Please share the information with your friends.

Yes (75.00%)

No (25.00%)

X

Please write what is wrong and leave recommendations on the article

Cancel reply

Rate this article: ( 4 votes, average: 4.75 out of 5)

Discuss the article:

Advantages and disadvantages

Advantages of Jaguar alarms:

1. Rich functionality. In their reviews, consumers note that Jaguar alarms have many useful options that make it easier to control not only the system itself, but also other components of the car.
2. Affordable price. You can buy an alarm system with auto start at a price of 5 thousand rubles and more. The cost will depend on additional features.

The disadvantages include the weak body of the key fob. If dropped regularly, the device quickly breaks down, and over time its buttons begin to sink. To prevent damage to the communicator, you can install it in a case. But it won’t help with buttons sticking.

TheAAG999 channel talked about the capabilities and disadvantages of Jaguar security systems.