Features of the Sherkhan Logicar 1 alarm system and detailed installation and operating instructions

Author: Victor

The Sherkhan Logicar 1 car alarm system is the manufacturer’s flagship product, which has extensive functionality, including the option of feedback from the vehicle. Also, thanks to the unique signal coding, the security system is highly resistant to hacking.

[Hide]

Specifications

The Sherkhan Logicar 1 car alarm system has the ability to automatically start the engine either instantly, upon command from the communicator, or delayed, using a timer. The car owner is notified about the condition of the vehicle and the occurrence of alarming situations using the control key fob. For this purpose, vibration or sound signals are used.

Parameters that this system has:

• protection of pulse signals from interception is carried out using a special proprietary encoding Magic Code PRO 2;
• in alert mode, the operating radius of the key fob will be up to 1.5 km, and when transmitting commands, the range of the device will decrease to 500 meters;
• the ability to activate and disable the security mode without using a communicator, using a special password;
• using a code to disable security step by step;
• the presence of three types of alarm signals - audio, optical (using optics), as well as transmission of pulses via a radio channel;
• data is sent at an operating frequency of 433 MHz;
• to protect power lines, safety elements, resistor devices, transistors, and diodes are used;
• The microprocessor module is powered from the on-board network at 9-18 volts;
• the value of current consumption by the alarm in security mode will be from 20 to 35 mA;
• All functions of the system can be performed at air temperatures from -40 to +85 degrees;
• AAA batteries are used to power the main remote control, CR2016 batteries are used for the additional remote control;
• The service life of the batteries in the main communicator is about 4 months, in the additional one - up to three years.

MAGICAR model settings

This car alarm model is characterized by a high level of reliability and ease of control. To avoid errors while setting up the autostart system, do not forget to turn off the engine and turn on the security mode.

Here are some useful commands executed from the key fob:

Calculate the timing of cranking the starter so that the car has time to warm up before you arrive.

All Sherkhan alarm systems are highly reliable, so all malfunctions in the settings are most often caused by the inability of car owners to use the security system. Read the operating instructions carefully to avoid any difficulties.

Equipment

The Scher Khan system delivery kit includes the following elements:

1. Service user manual for system maintenance and setup. The documentation allows you to correctly install, connect and program the anti-theft system.
2. Wiring diagrams for connecting car alarms.
3. Main microprocessor device.
4. Communicator with liquid crystal display. Intended for adjusting technical parameters and alarm functionality. The presence of a screen provides the possibility of two-way communication with the complex.
5. Spare pager, no display. Its main feature and difference from the main key fob is the absence of feedback and a warning system.
6. Alarm installation kit, which includes power cables and connectors.
7. Shock and sensitivity sensor. Designed to detect any shocks and other impacts on the car body. In accordance with the signals sent from the sensor, information is supplied to the main communicator and control unit. If the impact is serious, the protection function is activated.
8. Valet service key, used to activate the emergency alarm mode. Equipped with a cable with a plug for connection.
9. Transceiver module with connected header.
10. Power unit blocking relay.
11. Limit switch for mounting on the hood.
12. Siren with connection block.
13. Sticker for fixing the antenna module on the glass.

For complete protection, before installing the Sherkhan Logicar 1 alarm system, you must additionally purchase limit switches for the doors and trunk.

The Arnage channel spoke in detail about the configuration of the Logicar 1 anti-theft complex.

Instructions for Sherkhan Logicar 1

Instructions for use consist of the following sections:

1. Purpose of the alarm.
2. Equipment.
3. Additional components.
4. List of functions.
5. Technical specifications.
6. Description of the key fob functionality.
7. The procedure for arming, searching, opening the trunk lid, false alarms.
8. Emergency siren shutdown.
9. Modes, channel management.
10. Starting the power unit from a distance, blocking.
11. Adjustment and fine tuning of the sensor.
12. Individual programming of key fobs.

Related link:

Car alarm APS 2500 - the optimal combination of price and technical capabilities

Conclusion

The Sherkhan 1 car alarm is identical in technical characteristics to the Scher-Khan Universe 1 model. In general, this is a good budget security system for cars in the mid-price segment.

The basic set of functions is more than implemented. The connection and fine-tuning scheme is simple, and the operating principle is intuitive. However, be extremely careful, since the work involves voltage, power supply, and electrical equipment.

Main functions

Options that this alarm model has:

• the ability to synchronize the readings of communicators linked to the microprocessor module;
• option to control a second vehicle if it has a similar model of anti-theft system installed;
• presence of backlighting of the key fob screen;
• alarm option;
• online time display;
• locking buttons on the key fob;
• option to protect the car with the engine running;
• turning on the security mode without sound and alarm signals;
• the presence of five customizable channels for controlling additional electrical equipment;
• possibility of programming the type of power unit blocking relay;
• option to select the number of door lock control signals and their duration;
• closing and opening doors when activating and disabling the ignition system;
• the ability to monitor the intensity of engine operation in accordance with tachometer signals;
• option to automatically activate the protection mode;
• “Panic” function, which allows you to turn on alarms and lighting devices upon command from the remote control.

Functions related to automatic engine start:

• the ability to use this option on cars with manual or automatic transmission;
• setting up a remote start of an internal combustion engine (internal combustion engine) on vehicles equipped with a Start/Stop button to start the engine;
• the ability to use the function in cars equipped with diesel or gasoline power units;
• option to set the engine start time.

Characteristics of Scher-Khan Logicar 5i and Magicar 5

For a complete list of general characteristics, see the article: “Comparison of the functionality of the Scher-Khan Magicar 4 and Logicar 4 car alarms. Customer reviews”

Taking into account that the model of the Sherkhan Magikar 5 security system has been discontinued from mass production, it is not advisable to consider it as an accessory for installation

Advantages and disadvantages

The advantages of this Sherkhan model:

1. Extensive functionality. The alarm system is equipped with many options that not only protect the car, but also simplify its use: synchronization of communicators, silent security mode, delayed engine start.
2. High reliability. In fact, it is almost impossible to hack the Sherkhan Logicar 1 signaling system by intercepting the code due to the author’s signal encoding system.
3. Affordable price. The cost of the alarm ranges from 3,800 to 5,000 rubles, depending on the region of sale.
4. Decent build quality. All elements and devices that are included in the system are supplied in a durable protective case.
5. No false positives. If the sensitivity of the shock sensor is correctly configured, the consumer will not be faced with the activation of the alarm mode for no reason.

Disadvantages that an alarm may have:

1. Incorrect operation of the system, “glitches” are possible. Consumers usually encounter this problem as a result of errors made during installation. In particular, we are talking about incorrect connection of wires.
2. According to reviews, another drawback is the low efficiency of the alarm at subzero temperatures. In cold weather, the system may execute commands late; sometimes LogiCar 1 does not respond to signals from the key fob.

Sherkhan car alarm models

Car owners especially note the reliability and noise immunity of this brand's alarms. When developing the devices, we used our own software and technical developments. It was possible to combine compliance with high quality standards with low prices thanks to cooperation with South Korean manufacturers.

The circuits and designs of this car alarm are developed in Russia, and the components are manufactured in factories in South Korea.

The auto engine start function is available in such models as Magicar 7S, Magicar 7H, Logicar 3i, Logicar 4i, Logicar 5i, Mobicar 11, Mobicar A v. 1.0 and Mobicar A v. 2.0.

How to install an alarm?

The alarm can be installed in a garage. You must first prepare a set of tools for installation and also disconnect the battery.

To install an anti-theft system you need to have:

• multimeter for measuring voltage and determining breaks (short circuits) in electrical circuits;
• Screwdriver Set;
• set of socket wrenches;
• soldering iron;
• wire stripper;
• mounting blades for disassembling the interior;
• black electrical tape;
• foam;
• double sided tape;
• plastic clamps for fastening wiring.

Connection diagram

To connect the security complex, the following electrical circuit is used:

General card for connecting alarm elements (fragment 1)

General card for connecting alarm elements (fragment 2)

General card for connecting alarm elements (fragment 3)

General card for connecting alarm elements (fragment 4)

Step-by-step instruction

The installation procedure is as follows:

1. The microprocessor module is installed hidden in the vehicle interior. It can be located behind the instrument cluster, glove box or under the dashboard. It is advisable that in order to gain access to the device you have to disassemble the trim in the cabin, this will prevent the car from being stolen quickly. Double-sided tape or plastic ties are used to secure it.
2. The transceiver module is mounted in the upper corner of the windshield or rear window. It is important that the distance from the antenna to metal objects is at least 5 cm, this will avoid interference. Before installation, the glass surface must be cleaned. If the installation is carried out in winter, then its temperature can be at least 10 degrees Celsius. The wire from the antenna to the microprocessor module is laid under the decorative trim of the interior; during installation, care must be taken to ensure that the cable is not pinched.
3. The LED indicator is mounted in the corner of the front glass. First, its surface must be cleaned and degreased. You can embed the LED indicator into the dashboard, then you must first make a hole in it to install the light bulb.
4. The siren is located under the hood of the car, in a place that is maximally protected from external influences from under the bottom of the car. Do not install the siren near heating units and moving parts. It is recommended to place the device's horn down to prevent moisture from forming inside.
5. The hood limit switch is mounted on a metal surface that is as close to the body as possible. There should be no accumulation of moisture at the installation site. When the hood is locked, the sensor is protected by a rubber seal.
6. The shock sensor is fixed in the car using two bolts. During installation, it must be taken into account that the consumer must have access to the controller to change the sensitivity parameter. The sensor is equipped with two regulators. The first determines the sensitivity of the warning zone, and the second - the alarm zone. For fixation, it is better to choose the central part of the body so that the device detects physical impacts from all sides of the body.
7. If additional controllers are used, their installation is carried out taking into account the manufacturer’s recommendations. For example, the engine temperature sensor must be installed in the cooling system line.
8. After installing all the elements, they are connected to the control unit. The wires are laid under the decorative lining of the car interior.

Reprogramming and firmware

You can reflash the Magikar A key fob in two steps (code replacement is not used).

1. This action takes 4 seconds. Turn the ignition on three times. Turn it off. Confirmation – the hazard warning light flashes once.
2. Within four seconds, click the 1st key of the first remote control. This will be followed by a single flash of lights. Enter the passwords for the second and third switch. Hazard lights should flash once to confirm correct execution. After you enter the data for the third key fob, the optical instruments will blink twice and the alarm will exit the programming mode.

User manual

Before using the key fob, you must install a working power source in the device. The battery is inserted into a special compartment hidden under the back cover of the communicator. Polarity must be taken into account when installing.

Designations of buttons and symbols on the key fob

All indicator designations and button numbers on the transmitter:

Designation of button numbers on the key fob

Pager programming

Without programming the communicator, setting up the Sherkhan Logicar 1 alarm functions will be impossible.

To bind a new remote control, perform the following steps:

1. The car alarm security mode is disabled. The ignition in the car must be turned off.
2. The button on the LED housing is pressed and held for two seconds. The car's headlights should then blink.
3. Within the next five seconds the button is pressed again. If a password has been set to control the alarm, the car's headlights should blink twice. If there is a PIN code, the blinking will be single.
4. If a password is used, it is entered. If you don't have a PIN code, you don't need to do anything.
5. After five seconds the LED will start to light continuously. This indicates that the car alarm is entering the communicator's binding menu. No more than three remote controls can be registered in the memory of the Sherkhan Logicar 1 microprocessor alarm module.
6. Over the next 5 seconds, the first key fob button is pressed. To program other devices, similar steps are performed.

How to program autorun?

To configure automatic engine start, you need to use the programming tables given in the instructions.

1. In accordance with the table, it is necessary to move function 2-13 to the third position. This will allow the car owner to change the assignment of programmable channels to control the starter device and ignition system.
2. Using the communicator, you need to set the time period from the moment the starter is turned on until the time the power unit starts. In accordance with the table data, the closest value for function 2-20 is set. If the setting is carried out on a vehicle with a diesel engine, then the time period for option 2-21 is indicated. If there is a Start/Stop button in the car, the values ​​of function 2-25 are adjusted. In cars with a turbocharged engine, option 2-24 is changed.
3. Then you need to adjust the parameters to ensure smooth operation of the function. This refers to the warm-up time of the power unit, as well as the operation of the headlights in automatic start mode. Additionally, you need to configure the number of cycles to start the motor in remote mode; it is recommended to select no more than four. If the engine will be started using a timer, you must select a time interval.
4. After the time is set, you need to “click” on button 4 ten times.
5. To complete the settings of all values ​​and functions, you must simultaneously press the second and fourth keys of the key fob. The timer option will be enabled. To disable the automatic start function, similar steps are performed.

Programming table

Programmable functions menu [buttons (II+IV)]:

Anton Kovalev spoke about the operation of the autostart option using the example of the Logicar 2 model; in the case of the Logicar 1 alarm system, the implementation principle will be similar.

Operating modes

The Logicar 1 system can operate in different modes:

1. To activate security, use the first button of the key fob, and to disable it, use the second key. After turning off the protection mode, all door locks will open, the starter mechanism and the power unit will be unlocked. If, when the security is deactivated, the alarm sounds six times with a siren, this indicates that the alarm was working. In the case of five signals, the system was turned on as a result of receiving an impulse from the sensitivity sensor.
2. Activation of the vehicle search function in a parking lot is performed with the first button. When setting this option, car security must be turned off. The vehicle's lights will blink five times, and the communicator will play a melodic signal.
3. To open the luggage compartment, the third key fob button is pressed for 2 seconds. When security is turned on, the mode will be turned off automatically, but the locks on the doors will not open. If necessary, the consumer can configure this option with unlocking door locks.
4. To check the status of the car alarm, the fourth key is used; it is pressed briefly. After the “click”, the communicator display should display data on the operation of the anti-theft system.
5. The “Panic” mode is activated by pressing and holding the 1st key fob button for two seconds. To disable the option, you need to “click” on the first or second key.
6. Activation and deactivation of alarm signals by command is carried out by pressing buttons 1 and 2 on the key fob.
7. Turning on and off the Valet service mode is done by simultaneously “clicking” on keys 1 and 3. This function is used if the car remains at a service station for repairs.
8. To turn the sensitivity controller on and off remotely, press buttons 1 and 4 simultaneously.
9. Activation and deactivation of the key lock mode on the key fob is performed by briefly pressing the third and fourth. When the function is turned on, the communicator will emit a short pulse and the display will show “Hold”.
10. Activation of the security mode with the engine running is done by pressing the first button on the remote control. The ignition must be turned on and all doors, as well as the hood and trunk, must be locked. The door locks will be locked, the alarm will activate the security mode. If the protection is turned off or the siren is activated, the anti-theft system will automatically stop the engine and block its operation.

Setting up the “Pit Stop” mode, in which you can turn on the security with the engine running and when there is no key in the ignition, is done as follows:

1. When the power unit is running, the transmission selector is set to the neutral speed position. In the case of automatic transmissions, the lever must be set to Parking mode.
2. The handbrake lever is lifted.
3. The second key of the communicator is pressed for two seconds. The transmitter will emit a melodic signal, the car's lights should blink once. The ignition support option will be activated, and the car’s headlights will blink once every five seconds.
4. The key is then turned to the Off position to turn off the ignition. The power unit will continue to function for a certain time, configured in advance by the consumer.

A detailed description of the options for the Sherkhan Logicar 1 key fob is provided by the Buyer Notes channel.

Setting up LOGICAR

The latest model is also easy to operate. To configure autorun, all you need to do is:

1. Turn on the timer on the key fob by simultaneously pressing II and IV.
2. Set the required time by entering the programming mode by long pressing I + IV.
3. To activate the timed engine start, press IV 10 times in a row.
4. You can set the time to turn on the motor once a day (I), at 8 hours (II), 4 hours (III) and with an interval of 2 hours (IV).
5. After setting the parameters, turn on the timer by holding II and IV briefly.

The instructions for the car alarm describe in detail how to set the temperature start, as well as the engine warm-up settings. However, they are not very different from the models described above.

To make it easier to understand the features of Sherkhan alarms, watch the video on the topic:

Possible faults

Problems typical for this car alarm model:

1. The key fob does not perform its functions and does not send commands. The cause of the problem may be low batteries, mechanical failure of the device, or a software malfunction. If the power supply fails, the battery must be replaced. If the problem is the negative impact of moisture on the device, but the key fob must be disassembled and dried so that there are no traces of water left on its board. If the remote control is damaged, its internal components are replaced by resoldering.
2. The wires through which the alarm is connected are damaged. With long-term use of the security system, wear of the conductors is possible, in particular if they are laid next to moving elements and components. To find a damaged cable, you need to use a multimeter. After replacing the wires, it is recommended to wrap them with electrical tape to provide them with additional protection from wear and tear.
3. One of the elements of the security complex has failed. We are talking about a transceiver module, a sensitivity controller, and a microprocessor unit. A detailed check of each device will be required; first of all, it is necessary to ensure the integrity of the contacts through which they are connected. If the control unit fails as a result of exposure to moisture, then its housing must be disassembled and dried by disconnecting its parts. Software malfunctions of the microprocessor can be resolved by flashing, which is best left to specialists.
4. False alarms have appeared, the alarm is activated for no reason. This problem is usually caused by the sensitivity of the kick controller being set incorrectly. To eliminate the malfunction, this operating parameter must be reduced by adjusting the sensor. It is not recommended to set the sensitivity value to minimum.

Advantages and disadvantages

Advantages characteristic of Sherkhan Magikar 4 signals:

1. Autostart. The possibility of remote start ensures warming up of the power unit. Thanks to this, the consumer can start driving while sitting behind the wheel of a warmed-up car.
2. Two-way communication. This option provides convenient setup and adjustment of basic parameters. Through feedback, the consumer has the opportunity to find out the status of the anti-theft installation.
3. Budget cost.
4. Solid functionality. Many useful options allow you to ensure comfortable driving.
5. Long service life of batteries in communicators. This is achieved thanks to energy saving technology, which was used during the development of the pager.
6. Easy to adjust parameters. Users note that the communicator is characterized by a simple and intuitive menu, which allows you to quickly adjust all parameters. In addition, the technical manual describes in detail all the nuances of setup.

Disadvantages that users note in their reviews:

1. Unreliability of the system. Despite the great functionality, in fact, a professional thief will be able to hack the alarm. Conversational signal encoding is ineffective if handled by a professional.
2. The appearance of failures. Some consumers note that system malfunctions may occur within a few months after installation. This may be due to errors made during installation and configuration. But many users point out this drawback.
3. Weak communicator body. The device is not shock-resistant, so it may break after just a few falls.
4. A large number of false positives. Users indicate that alarms are triggered for no reason often in cloudy and humid weather.
5. Low communicator volume. If the alarm goes off and the consumer is in a noisy place, he may not hear the pager.

Video

The “Scherkhanalarm” channel spoke in detail about the security options of the Logicar 1 anti-theft system.

Do you have any questions? Specialists and readers of the AUTODVIG website will help you ask a question

Was this article helpful?

Thank you for your opinion!

The article was useful. Please share the information with your friends.

Yes (75.00%)

No (25.00%)

X

Please write what is wrong and leave recommendations on the article

Cancel reply

Rate this article: ( 4 votes, average: 4.75 out of 5)

Discuss the article:

What are the benefits of an alarm?

This alarm has many advantages.

• One of these benefits is protecting the system from scanning.

This will help protect the car from illegal scanning of the car system, and in the future from hacking. After all, there are quite a few cases of burglary. Even if you leave the car with the engine running, the alarm will still be turned on and will take care of the safety of your car.

• The next advantage of this alarm is that the car is automatically armed.

It may happen that when leaving, you forgot to arm your car. The alarm itself takes care of this. After some time of inactivity of your car’s engine, the alarm system will automatically protect it.

And this is very convenient, because everyday life is full of various activities and a person becomes more distracted. Therefore, having such an alarm system, you have nothing to worry about.

Design and packaging

The device is packaged in a bright box. Each element, regardless of whether it is the central key fob, instructions or antenna, has its own place in the blister backing. Everything looks neat and harmonious.

Unlike the packaging design, the device has the same appearance as its predecessor. However, it seems so only at first glance

The manufacturer paid great attention to the connectors (the number of contacts was increased) and the electronic part of the alarm system

All 4 keys are located on the back side of the case, while the entire front part is occupied by the LCD screen. A similar solution in the field of ergonomics is common on all models of the series. And this makes no sense - using the key fob is extremely convenient, practical and intuitive, while the risk of accidentally pressing the button is minimal.

How to turn on Webasto from the Sherkhan remote control button?

What do you press on the Scher-Khan key fob to start the preheater?

1. The device communicates with the switch via an additional channel. This could be key 2.
2. Pressing button 2 for more than two seconds turns the heater on and off.
3. The Webasto timer does not need to be used.
4. The pre-heater should only be connected to a car alarm in specialized centers.