Top pipe is hot bottom pipe is cold cause

A hot top and cold bottom of a car radiator is a normal condition only for cold engine after launch. If the engine has been running for several minutes, during which the coolant temperature has already reached 80–90 degrees (depending on the model), and the upper radiator pipe is hot and the lower one is cold, this is sign of trouble in the cooling system. However, there are exceptions to this rule.

The main reasons why the lower radiator hose is cold after warming up are a malfunction of the thermostat or pump , or a clogged radiator . This article will tell you how to determine the specific cause of the problem and what to do in this case.

Why is the lower radiator hose cold and the upper hose hot?

138 6 116k

263 5 272k

A hot top and cold bottom of a car radiator is a normal condition only for an unheated engine after starting. If the engine has been running for several minutes, during which the coolant temperature has already reached 80–90 degrees (depending on the model), and the upper radiator pipe is hot and the lower one is cold, this is a sign of a problem in the cooling system.
However, there are exceptions to this rule. The main reasons why the lower radiator hose is cold after warming up are a malfunction of the thermostat or pump , or a clogged radiator . This article will tell you how to determine the specific cause of the problem and what to do in this case.

The engine does not reach operating temperature

You can monitor the temperature readings of the power unit directly from inside the car. The dashboard of all modern cars has a small information field, usually round or semicircular in shape, showing the driver the coolant temperature readings. This is the device that gives an idea of the temperature conditions in which the engine is operating at a given time.

If the temperature gauge does not reach 90 degrees during a long trip, you should seriously think about finding the cause of the deviation from the normal operation of the power unit. It is not recommended to delay its diagnosis, because prolonged operation of the motor in this mode will lead to wear of its internal components.

The fact is that the electronic control unit, which is popularly called the “brains” of the car, recognizes an engine that has not reached the nominal temperature as cold, and therefore the fuel system injects an over-enriched mixture.

Working in this mode leads to heavy carbon deposits on the spark plugs and, accordingly, on the internal elements of the engine, which in the future will lead to the need for a major engine overhaul.

How does the engine warm up?

Each serviceable unit has a different warm-up time. It is influenced by:

degree of forcing;
engine type: diesel or gasoline;
cooling system condition;
stove operation;
quality of antifreeze or antifreeze;
outside air temperature;
type and viscosity of engine oil.

The characteristics of the oil are rarely taken into account, but experts believe that this is necessary. Various friction reducing additives and the base stock, synthetic or semi-synthetic, affect the performance in the range of 5–7 degrees. Thus, the engine will heat up faster with thinner synthetic oil.

The engine temperature gauge does not rise often due to a malfunction of the thermostat.

It is with this unit that the system check always begins if the engine takes a long time to warm up to operating temperature.

Principle of operation

Coolant enters the radiator through the thermostat. This is a large circle of fluid circulation. The thermostat usually opens at a temperature of 100 degrees Celsius. If the temperature has not reached this limit, then the liquid moves in a small circle. A thermostat malfunction is manifested by improper opening of the valves.

When the thermostat is closed, the engine overheats, and a constantly open one leads to low temperatures, since the liquid will only flow in a large circle.

Due to irregular changes of antifreeze or antifreeze, use of running water or mixing of coolants, various deposits in the form of scale may accumulate in the system. In this case, the thermostat will inevitably jam in one of its positions.

It is important to know

Beginners often make the mistake of believing that the lower pipe should never be cold, and they begin to sound the alarm.

(especially useful during winter): Drive the car into the garage. Let the engine run for 10-20 minutes so that this same pipe has time to heat up, and only then draw your conclusions. The fact is that due to the lack of heat in the cooling system (cold season), the thermostat keeps a large circulation circle closed. If the heater is on, it will prevent the thermostat from opening. Therefore, it must be turned off while the engine is warming up. If after this the lower pipe is cold, there is a problem.

Dirty radiator

The main reason for this, according to most experts, is a clogged radiator

. Over time, this important element of the cooling system becomes clogged with rust residue, dust, leaves and other debris. The location of the radiator is in front of the car. So, no matter what happens, it gets inside. Ultimately, all this leads to problems.

Since this reason is the most important, below is a method on how to clean a radiator. In addition, proper care of the radiator and its regular maintenance ensures the normal operation of the entire cooling system.

Causes of poor coolant circulation

According to the above diagram, the reason that the lower radiator pipe in the VAZ 2110, 2114, 2115 remains cold is the lack of fluid circulation in a large circle of the system. Note that the radiator is the main cooling element. Therefore, the upper pipe through which the liquid enters the heat exchanger will be hotter than the lower one, even if the liquid circulates correctly.

Possible causes of stagnation in the cooling system:

radiator clogged;
non-working thermostat;
airlock;
pump breakdown.

Any intervention in the engine cooling system requires subsequent flushing of the ODS and replacement of the coolant. Poor quality coolant cannot cope with cooling the engine and can cause a blockage in the system.

Cleaning or replacing the radiator

The radiator, located in the front of the car, absorbs the main flow of dust and dirt. For its effective operation, timely prevention and cleaning is necessary. The radiator can become dirty both inside and outside.

An indicator of internal cleanliness is the condition of the coolant. Manufacturers recommend changing antifreeze every 75,000 km or every 5 years. However, a change in the color of the liquid, severe darkening, discoloration, or the presence of rust requires urgent replacement of the coolant. It is recommended to change antifreeze at least every 40,000 km.

Removing the air lock

Signs of the formation of an air lock in the cooling system are rapid warming up of the car to high temperatures and poor performance of the interior heater. This can be especially easy to notice in winter. The reasons for the appearance of an air lock are different:

incorrect filling of coolant;
engine overheating;
depressurization of the system;
damage to some parts, etc.

If, during the inspection, leakage of antifreeze (antifreeze) is detected in the system, traces of coolant on the engine or other places, the causes of the leak should be eliminated. Often depressurization occurs due to poor tightening of clamps on pipes and hoses. They need to be tightened up. Any deformed or faulty parts found should be replaced.

There are several ways to remove air pockets. The easiest one is to drive up a steep hill with your face up. Unscrew the radiator and expansion tank caps. Let the car warm up for 10-15 minutes. Then release the gas a little and fill the system with coolant to the required level. Continue until bubbles stop appearing.

In VAZ 2110, 2114, 2115 cars, airing is rare. The cause of similar symptoms may be clogged hoses or radiator.

Why does the heater on a VAZ 2109 blow cold air at idle?

The cold from the stove in winter is a good reason to stop using your car. The stove is part of the car's cooling system. The antifreeze heats up from the engine and moves into the radiator, which is blown by a fan. Cabin air is distributed thanks to deflectors. The air flow from the fan moves through the heat exchanger and bypasses it. This is the temperature control algorithm.

Possible problems with the stove:

the fan works partially (limited in speed mode) or shows no signs of life;
stove operation is limited in directions;
heating system and temperature controller are in conflict (the stove only blows hot or cold air).

Regularly check the level and quality of antifreeze in your car. A dark orange color indicates that the antifreeze has expired.

Cooling system hoses are inflated

First things first: Passat car 1995, ADZ engine - 1.8l. How it started: antifreeze began to leak from the gap between the tee (which has a temperature sensor) and the engine. Because it was minus 30-40 outside and there was no desire to climb, I just added antifreeze as needed. I didn’t pay attention to the pipes and others (if there is a leak, you first need to seal it, and only then look further) Now it’s warmer and on Sunday I fixed all the leaks (I found 2 more).

The problem is this: the hoses on the radiator inflate and antifreeze is forced from the expansion tank into. I think the cooling system. What I have already done (except for eliminating the leak): - I made sure that the fan on the radiator is working and it seems that the thermostat in the engine is also alive. I checked it this way: I started the cold engine and checked the temperature of the radiator with my hand. At the beginning, only the top became warmer (the bottom was cold, that is, there was a temperature difference and that meant the thermostat was closed). Using the temperature sensor on the dashboard, I waited for the temperature to be approximately 90 degrees and touched the radiator - it was equally hot from the top and bottom and on the sides - in general, it was hot everywhere. So the thermostat opened. I sat down again and pressed the gas, like warming it up (it’s like minus 10 outside) for about . (but less than 95) degrees the fan turned on and quickly cooled everything down to less than 90. - I tried to expel the air from the stove. I don’t know the technology for passats, so I did it as I once did on the figure eight - I sharply squeezed the lower pipe with my hand (like creating pressure). I tried to drive it out by starting the engine with the cap on the expansion tank open. In general, I don’t know if I kicked it out or not, but the stove heats up like crazy. At the same time I noticed this thing - antifreeze is constantly being released into the reservoir through the upper pipe (thin). I called my mechanic and outlined the problem, but there were no ideas. I read the forum - I really didn’t find anything (except maybe change the cylinder head gasket - maybe gases are breaking into the cooling system. But there is no oil or foreign smell in the coolant.) I’ll take off the spark plugs at lunchtime and see what kind of carbon deposits are on them.) A month ago the changers were black, like rich mixture, but this is understandable - it’s still minus 40, idling for 6-8 hours, starting cold, etc.) In general, I don’t know what to do next :-(((Help with advice.

Filling with new coolant Kalina

The installation of new pipes is complete. Now the most interesting part is that you need to fill in new antifreeze. Don't forget to tighten the bolts from the drain holes back. I use Felix Green G11. To avoid the occurrence of a large number of air pockets, before filling in the coolant, I removed one hose from the throttle heating - the highest point of the cooling system. During the process of filling the system, air could be heard escaping. Out of 10 kg of antifreeze, about 2 liters remain in the canister.

I filled it up to the MAX mark on the expansion tank and put the hose from the throttle back in place. Now you can try to start the engine and see what happens. Before this, of course, you need to put in place the ignition module and the air filter along with the mass air flow sensor and the adsorber valve.

After the first start, the engine heated up to 120 degrees, but the radiator remained cold. I waited about 10 minutes until the engine cooled down and SLOWLY unscrewed the cap from the expansion tank, releasing the pressure, and then unscrewed it completely. At that moment I heard a gurgling sound - excess air was coming out. Some fluid has leaked into the system. I added new fluid to the reservoir and started the engine again. This time everything worked as it should - the radiator warmed up, the fan turned on, the stove was heating, the temperature stayed around 90º.

And on this positive note, the procedure for replacing the pipes on Kalina, as well as the thermostat and antifreeze, can be considered completed.

Causes of poor coolant circulation

Possible causes of stagnation in the cooling system:

radiator clogged;
non-working thermostat;
airlock;
pump breakdown.

When to change?

Let's remember Soviet times, when all radiators, including products for the heating system, were made of copper. These units had enviable reliability, so replacing the stove radiator was one of the rare procedures, and maintainability was not in doubt. Sometimes it became necessary to clean the cavities of these products from the accumulated scale.

The beginning of the 90s was marked by the appearance of aluminum radiators, which were cheaper. Such units have gained considerable popularity among manufacturers, who still resort to installing them in their new and existing models of cars. AvtoVAZ also professes this trend, heroically equipping the Lada Kalina with aluminum versions of radiators.

The use of products of this type causes a number of problems:

The aluminum product does not have durability and tends to develop leaks after a couple of years of intensive use. Such a case does not involve repair, since it is not possible to eliminate the leak in the product.
Coolant evaporating through a leaking radiator creates toxic fumes that penetrate the cabin, have a sweetish taste and settle on the windows in the form of fogging, similar to greasy stains.
Structurally, the manufacturer placed the on-board system controller under this radiator. If antifreeze gets inside this device, it will fail. Replacing the controller is not cheap, so taking steps to replace the radiator as soon as possible is a good idea here.
Access to the radiator assembly is very difficult, so even such an event as cleaning is a very labor-intensive task.

Among the main reasons causing antifreeze leakage from the heating radiator is the use of cheap antifreeze by Lada Kalina owners. There are plenty of fakes on the market, so careful selection is one of the keys to trouble-free operation of the heating system. Counterfeits contain the presence of various harmful substances that have a negative effect on the aluminum structure, causing leakage.

Today, special sealing substances designed to seal a small leak from the inside have become quite popular on sale. This method is not always able to provide help, but the risk of clogging the entire cooling circuit is quite high. You should not trust such components, but should be inclined to replace the radiator as soon as possible.

Which modification of this element should I choose? Most owners unanimously recommend DAAZ (Dimitrovgrad Automobile Assembly Plant) products.

The lower radiator hose is cold and the upper hose is hot, what is the reason?

, 05 Dec 2013 17:23

Page 1 of 7
1
2
3

Further
»

To reply, please log in to the forum first.

#1

Omega waters
72 Posts:
Gender: Man
Vehicle characteristics: Opel Omega, 1992, gearbox-5, C20NE (without lambda)
Name: Alexander
Donetsk city

Hello everyone, OOA C20NE, my lower radiator pipe is always cold, while the top of the radiator and the pipe itself are hot, what could be the reason? Of course, I understand that this could be a plug or the thermostat is sticking, the lower radiator hose is cold, while on the tidy it’s 100-105 degrees, and when I turn on the heater (it’s blowing hot), the temperature in the cabin drops by 90 degrees throughout) so as not to boil the upper part The radiator is hot, air is expelled. What could this be? I replaced the thermostat, it didn't help! and one more thing I noticed is that there is no pressure in the system! The pipes are all soft, and when you try to unscrew the cap from the expansion tank with the engine turned off, no hissing occurs!

#2

Regular visitors

51 Posts:

Gender: Man
Vehicle characteristics: Opel Omega B, 1998, manual transmission, X20XEV
Name: Vladimir
City: Velikiye Luki

How's the pump doing? Have you tried bleeding the radiator? You can also check the opening thermostat in hot water, maybe it will.

#3

Topic author

Omega waters

72 Posts:

Gender: Man
Vehicle characteristics: Opel Omega, 1992, gearbox-5, C20NE (without lambda)
Name: Alexander
Donetsk city

squeezes the pipe

Sanderis » November 16, 2013, 00:06 » Message No. 200394

Guys, help! The engine is cooling down and compressing the pipe going to the radiator. What could be wrong?

satiriaz » Nov 16, 2013, 01:19 pm » Message No. 200404

As far as I know, this is how it should be

Yuri » November 16, 2013, 14:43 » Message No. 200411

It shouldn't be this way. Either the valve is not working correctly, or there is no normal flow of liquid from the expander, or the pipe is running out.

Sanderis » November 16, 2013, 16:09 » Message No. 200416

Thanks guys) valve, do you mean thermostat?)

Alexander_01 » November 16, 2013, 16:36 » Message No. 200417

The topic has already been covered from all sides. Yuri listed everything. But most often it is a tired pipe.

X 666 » November 16, 2013, 19:39 » Message No. 200425

The sooner you change the pipe, it is already tired. I have already gone through this, see the link https://mazda-xedos.ru/problema-v-prokladke-golovki-bloka-foto-vt4949.html

Sanderis » November 17, 2013, 14:32 » Message No. 200452

I’ll change the pipe and then we’ll see if the sore goes away or not :-) thank you all for your help :-)

satiriaz » November 17, 2013, 17:50 » Message No. 200454

Damn! And a couple of years ago the service center told me that such a sunken pipe is even good! I’m still happy to drive

kakovkin1234 » November 17, 2013, 19:53 » Message No. 200458

Also check if the small hose going to the expansion tank is clogged. Mine was clogged. To check, remove the cap from the tank and blow. It should be easy to blow through.

valve » November 17, 2013, 19:57 » Message No. 200459

+1 I have the same crap with the pipe. somehow I didn’t even attach much importance to it. There have never been any problems with cooling. The antifreeze doesn't seem to go away.

Alexander_01 » November 18, 2013, 15:21 » Message No. 200468

Yes, this is not a problem at all. Just the answer to why it shrinks. He's tired. I don’t remember that members of the forum were torn from old age.

X 666 » 18 Nov 2013, 17:53 » Message No. 200474

It will definitely not burst, but the coolant from the expansion tank may not be tightened; because of this, I overheated the engine once.

DervishVit » November 19, 2013, 10:39 » Message No. 200495

I was torn when gas was leaking from under the gasket. I was lucky that it broke at the top and some liquid leaked out.

Alexander_01 » November 19, 2013, 15:16 » Message No. 200503

What to do if the engine overheats

First of all, it should be remembered that if the overheating is short-term (for example, the temperature needle rises in a traffic jam), then you should observe whether the temperature will drop after you start driving (counter air flow appears) or as a result of turning on the radiator fan.

If the car was already in motion and the engine temperature reached a critical level, you should not immediately turn off the engine. Also, you should not try to cool the engine by pouring water on it from outside, pouring cold water into the radiator, etc. Such actions will lead to the need to repair the internal combustion engine, and it may be necessary to change the BC and cylinder head.

Next, you need to wait a few minutes, while simultaneously inspecting for obvious and strong signs of antifreeze/antifreeze leakage under the car or in the engine compartment. If no leaks are visible, but the temperature does not drop, the unit must be turned off.

Please note that you need to immediately turn off the engine when steam starts coming out from under the hood; traces of intense coolant leakage are clearly visible. In this case, the engine must be stopped, without expecting that turning on the stove will reduce the heating.

Why does the heater in a Lada Kalina car blow cold air?

Breakdowns are common not only to old, but also to new cars. Some owners of Lada cars notice that the heater blows cold air; Kalina may also be susceptible to this problem. This can happen for many reasons.

Regardless of this, it is better not to delay repairs. Here, as in the human body, one small violation can trigger a chain reaction. You can deal with such a breakdown yourself or in a service station.

Attention to every detail

It is easier to prevent a technical malfunction than to spend time and money fixing it later

In order to avoid having to repair the stove on your Lada (it doesn’t matter whether it’s Kalina or Vesta), you need to carefully monitor the technical condition of the car:

every morning at Kalina’s parking lot, you need to check for dark spots indicating an antifreeze leak;
inspect the system hoses for leaks;
if any are found, then it is necessary to immediately change the tank cap;
daily inspection of the stove radiator;
If the stove blows cold air, then the reason should be sought in increased coolant consumption.

Daily checks of the vehicle’s “health” will help avoid many problems.

If the radiator valve is loose or the coolant reservoir is leaking, the problem will spread at an alarming rate within a short time.

The first result will be a breakdown of the vehicle's computer. Such a malfunction is not covered under warranty, so repairing the heater and replacing the computer will fall entirely on the shoulders of the car enthusiast. A small rearrangement of the on-board computer will help reduce the risk of such troubles for Kalina:

carefully dismantle the cladding;
unscrew 2 screws;
gently squeeze the computer towards you;
place it on a shelf in the glove compartment area;
There is no need to disconnect the wiring harnesses;
fix the computer in a new place;
re-grounding is not carried out.

If everything is done correctly, then in the future the Lada Kalina will not be left without an on-board computer, even in the event of an unexpected problem. The main thing is for the driver to make sure that the fastenings are secure after rearrangement.

Technical specifics of restoration of functionality

In most cases, repairing a heater takes little time. If the Lada Kalina requires one, then if you have the necessary tools, you can do everything yourself.

In order to solve the problem with the stove on Kalina, you need to perform the following sequence of actions:

drain all coolant;
remove the air filter (the heater damper cannot be removed);
the brake and gas pedal are dismantled for more convenient replacement of the radiator;
in some cases there is a need to dismantle the steering structure assembly;
the battery is removed together with the stand;
remove the air duct;
carefully unscrew the hose from the radiator;
The interior heating hose is dismantled.

To save time in the future, it is necessary to fix the position of the parts in space. This will allow you to avoid delaying the repair of the Kalina heater. In some cases, the above algorithm does not work fully. The culprit here is the individual characteristics of the vehicle. In this case, there is no need to rush or start using brute force.

Experienced drivers recommend removing more parts and components of the vehicle, which will ultimately make it possible to replace the radiator and grille.

Regardless of the complexity of the repair, you must ensure that the coolant has been properly drained and then refilled. Any drips and leaks can negatively affect the technical condition of the iron horse.

During repairs, the car owner may notice wear and tear on some parts of the car. In this case, they should be replaced.

Firstly, this will eliminate the risk of repeated repairs. It is impossible to predict exactly when the car will start to feel unwell. Secondly, high-quality operation of the vehicle saves time and money that the driver would have spent on visiting a service station.

Why does the radiator pipe shrink and burst?

One of the dangerous manifestations of a malfunctioning cooling system is a violation of the geometry of the radiator pipes. Why is the situation dangerous if the inlet or outlet pipes of the radiator flatten when the engine has cooled down, and when warmed up they gradually return to their normal state? Why is this happening, can I solve the problem on my own?

About pressure in the cooling system

To effectively remove heat from the engine jacket, liquid cooling systems are hermetically sealed from the environment and can withstand pressure from 1.2 to 2 or more atmospheres. This is necessary to prevent the coolant from boiling when the temperature reaches 100°C. At elevated pressure, various brands of antifreeze and antifreeze can boil when heated to 107°C−120°C, and sometimes 150°C.

Technical means to increase pressure in the cooling system are not used. The required values are achieved due to a natural increase in the volume of heated liquid circulating in the “jacket” of a running engine. Excess pressure is released through the system expansion tank cap, equipped with special valves, in which a certain amount of air is always present.

Bends and cracks in radiator pipes

The excess air released during the expansion of antifreeze or antifreeze in the tank after stopping and cooling the engine is compensated from the atmosphere through the second check valve of the lid. If this does not happen, a vacuum is created in the tank, radiator, connecting pipes and engine jacket. The first to react to this by compression are the least durable elements of the system - the rubber radiator pipes.

The maximum possible value of negative (compared to atmospheric) coolant pressure depends on the temperature difference between the heated and cooled engine. It is no coincidence that motorists notice this problem in winter, when the temperature range is greatest. In this case, the pipes wear out quickly and, having lost their initial elasticity, can burst. The vehicle cannot be operated with such a malfunction.

Expansion tank cap: design features

In addition to the plastic body, threaded part and sealing gasket, the tank lid is equipped with two valves: inlet and outlet. Each of them is designed and must operate under certain conditions. The first opens at excess pressure - for example, 1.2 Bar. The second is needed to compensate for pressure when the antifreeze cools down. If this valve fails, a dangerous level of vacuum is created in the system.

The solution to the problem is to flush the valves or buy a new cap.

The metal parts of the valves may simply be clogged with dirt from the cooling system if it has not been flushed for a long time. In such cases, the problem can be temporarily eliminated by blowing and cleaning the lid valves. If there are repeated failures, you will have to start with a general flush of the entire cooling circuit. If the valve malfunction is due to corrosion of their metal elements, you should purchase a new cover.

How to identify a malfunction

In order to make sure that the radiator pipes are flattened precisely because of the strong vacuum in the cooling system, and the reservoir cap is to blame, it is enough to unscrew the latter a little (only on a cold engine). A characteristic whistle of incoming air will indicate a clogged or rusted check valve. If there is no whistle, you need to flush the entire system. In this case, it is better to start with the upper radiator pipe, which connects it to the expansion tank.

Why buying a new cover may not solve the problem

Unfortunately, the simplest part costing a few rubles does not always meet the requirements. The lid may not function due to a significant difference in pressure at which the valves installed in it open or close. You can check their serviceability and response threshold using a compressor for inflating tires, and adjust it by reducing the number of turns of the corresponding spring. Or simply buy and install a cover from another manufacturer.

What can be done?

If the car is not warming up well, you can inspect the thermostat yourself.

Checking the functionality of the thermostat

The design of the device implies sensitivity to changes in temperature. The pressure in the coolant system does not affect the restriction of antifreeze circulation through the small circuit, cylinder head and block cooling space. As the temperature difference between the engine and the environment increases, the thermostat gradually opens the coolant supply from the main radiator to the engine.

The same thing happens when the difference in indicators decreases. This process helps maintain and limit the temperature limit of the engine, as well as heat the interior of the car. To determine if the thermostat is working properly, you do not need to remove it.

You can detect a breakdown manually when starting the engine. When it has warmed up for 5 minutes, you can check the device.

Starting will cause coolant to circulate through the engine's cooling passages. Heating of the coolant begins in the engine and radiator of the car. The pipe going in the opposite direction from the radiator to the engine should not be hot. If this happens, then there is a problem with the thermostat.

Removing the air tube

The main reasons for poor heating in winter include air lock. It is useful for a car driver to have the knowledge and skills to remove air from the system. Its accumulation occurs at the highest point - the throttle assembly. From there you need to remove the air plug. The sequence of actions is as follows:

Unscrew the filling cap on the engine, remove the screen and screw the cap into place to avoid contamination of the crankcase.
Find 2 pipes, which are located side by side in the throttle assembly, and pull out 1 of them.
Open the coolant expansion tank and cover it with a clean cloth.
Blow slowly into the tank until antifreeze flows out of the hose.
Put the tube back on and tighten the clamp quickly so that no air gets into the pipe.

This scheme is suitable for the VAZ 2114. When clogging of the cooling paths occurs frequently, check the entire system, which may be depressurized. If after these steps the engine temperature does not rise, then you need to look for another source of problems.

Engine insulation

By insulating the engine, you cannot get rid of all problems with warming up. If the engine is properly insulated, it will not require prolonged warming up during the day, and the coolant temperature will be normal. To insulate domestic equipment, heat-insulating material is installed between the radiator and the front grille. The motorist can use cardboard or buy special insulation.

In a purchased product, the padding consists of synthetic insulation covered with a leather substitute. It has the advantage of special holes that open when the temperature rises. Insulation can be achieved by installing a heat insulator under the hood. Special blankets have been developed for this purpose.

You can buy them or make them yourself from felt, mineral wool or other material. This type of thermal insulation helps prevent a layer of ice from freezing on the hood, which often happens in winter when snow falls on the car, melts and freezes. The heat insulator can be glued to the lower engine protection. In the future, it will need to be cleaned of dirt so that it does not get into the engine.