The windshield on the 2114 has a size of 1400x662mm, it is standard for the model range from model 8 to model 15. The windshield has a three-layer structure, also called triplex. It consists of two layers of glass and a transparent film in the middle, which prevents the glass from shattering upon impact.
There are cases that require windshield replacement. The main reason is the condition of our roads. From an oncoming or overtaking car, a small pebble may fly from under their wheels and damage the glass.
Main types of damage:
- chips;
- cracks.
If a chip appears, that is, only the outer side of the triplex is damaged, problems usually do not arise. But when a crack appears, you need to take action, otherwise over time the windshield may fall out, which can easily lead to an accident or accident. And it will be difficult to obtain a diagnostic card.
What you can do:
- in case of small chips, continue to operate the car;
- If there is a crack, take temporary measures yourself or replace the glass.
Temporary measures:
- Using a glass cutter, half a centimeter cuts are made perpendicularly along the edges of the crack;
- Using the finest diamond drill, holes are drilled along its edges. The crack will not spread further for some time;
- contacting a specialized service, where the crack can be “welded” so that it will not be visible.
But in any case, the integrity of the triplex has already been compromised and after some time the glass will have to be replaced.
Replacement of side glass on VAZ 2113, VAZ 2114, VAZ 2115
The side window performs important functions in the car:
Note! You will need the following tools: a screwdriver, wrenches or socket wrenches, and new glass. We remind you that take the new glass together with the frame, otherwise, if you buy it separately, you will be tortured by installing the frame on the glass and aligning it.
Clip location
Placed at the bottom center (indicated by the blue arrow, and the glass is shown by the red arrow). The frame is inserted into the glass, over time it weakens and there are even cases when the glass fits askew into the door. The weakened clip does not hold the glass; it dangles in the door. The glass is attached to the window lifter using this clip. In general, the detail is necessary and irreplaceable. In the event of a fault, there are two options:
When should you replace your side glass?
In principle, the time of replacement is a personal matter for each owner. Some people change glass for aesthetic reasons, others because of damage. However, there are a number of recommendations:
Common faults
Old and new mechanism
One of the most common malfunctions is gear wear. Usually plastic is used, which wears out quickly over time. A symptom of this problem is a rumble and crackling sound that is heard when the glass is raised or lowered.
Also, the automatic switch on the power windows may burn out, which is why the inclusion will not work. Also, problems may arise with the rear doors. They either stop working altogether or respond to pressing a key from the main unit, but not on the doors themselves. Check current continuity.
The electric motor may also fail. To fix it, you will need to check the voltage in it and the wiring. Mechanical damage to the guides may also occur.
Replacing side glass on a VAZ 2113-VAZ 2115
Removal
1) The glass on the front and rear doors is removed in almost the same way. We will look at both options, but start with the front. You will need the help of an outsider. Have a helper hold the glass to prevent it from falling. And you lift the glass all the way up and unscrew the bolts securing the window regulator to the glass frame. Just in case, we will analyze the situation without an assistant. Then, at the beginning of the operation, the side window is blocked with a screwdriver, preventing it from falling (photo 1), then the door trim is completely removed (read more in the article: “Replacing a door on a car”, from point 1 to point, and the two bolts securing the clip to the window lifter are turned out ( photo 3). Having unscrewed the bolts, carefully begin to remove the seals in the door in which you are replacing the glass (photo 2). Please note that you will have to remove the screwdriver to remove the seal from the glass, remove it carefully and hold the glass. After these operations, tilt the glass in side and remove (shown in the fourth picture).
Note! When working with an assistant, there is no need to insert a screwdriver. Immediately remove the seals from the door and unscrew the cage bolts, and let an assistant hold the glass. After unscrewing the bolts, roll the glass on its side and remove it from the car door!
2) With the rear doors, the procedure is similar: insert a screwdriver, remove the trim from the door and unscrew the two bolts (photo 3) of the cage. Then the rubber seals are removed from the door (photos 1 and 2), the glass is rolled on its side and removed from the car door (photo 4).
The new part is installed in the reverse order of removal. If you bought glass without a frame, you will definitely have to install it. Take soap or WD-40 and coat the inside of the clip, then install the clip on the glass. Place the glass in the sun to dry quickly. Be sure to monitor the drying process, wet lubricant will not hold the clip, it will be removed from the glass and it will fall.
Additional video Attached below is a video on today's topic using the example of cars of the Samara and Samara 2 families, we recommend that you watch it.
Source
How to choose and replace glass on VAZ 2114, 2115 cars
Side glass performs important functions in a car:
Note! You will need the following tools: a screwdriver, wrenches or socket wrenches, and new glass. We remind you that take the new glass together with the frame, otherwise, if you buy it separately, you will be tortured by installing the frame on the glass and aligning it.
Clip location
Placed at the bottom center (indicated by the blue arrow, and the glass is shown by the red arrow). The frame is inserted into the glass, over time it weakens and there are even cases when the glass fits askew into the door. The weakened clip does not hold the glass; it dangles in the door. The glass is attached to the window lifter using this clip. In general, the detail is necessary and irreplaceable. In the event of a fault, there are two options:
When should you replace your side glass?
In principle, the time of replacement is a personal matter for each owner. Some people change glass for aesthetic reasons, others because of damage. However, there are a number of recommendations:
Design and dimensions
Consumables that do not match in size are one of the reasons for rapid breakdown. To prevent troubles, take the choice of a new part more seriously.
Head-on
The dimensions of the windshield of the VAZ 2115 are 1400×662 mm. The dimensions of the windshield on the VAZ 2114 and 2113 have the same dimensions, which makes it easier to find a new spare part.
It is multi-component: two glass layers and a film between them, the so-called triplex. This structure prevents fragments from scattering when damaged.
Rear
Cracks or chips on parts are rare. The size of the rear window of the VAZ 2114 is 1210x656 mm.
The parameters need to be known if the driver wants to tint the car.
Lateral
The front left side glass is 858 mm wide and 528 mm long. Consult with a salesperson at your auto store before purchasing.
Manufacturers
Now there are many manufacturers of automobile glass. Conventionally, they can be divided into four categories - European manufacturers, domestic, Asian and original glasses. European-made glass is distinguished by good strength, it easily withstands small impacts and practically does not scratch.
A windshield made in Europe always fits in size, does not distort objects, and the polymer film does not lose its color for a very long time.
The products of domestic manufacturers cannot be characterized unambiguously, since in the same price segment there can be both good and bad glass. First of all, it depends on the composition of the glass itself.
The characteristics of the polymer film are also important - low-quality film quickly fades or fades, which can affect the comfort of driving. Sometimes small manufacturers have windshields with incorrect geometry - they may not fit into the opening, or they may fit, but with a skew.
In the second case, this does not affect the operation of the car, but since the glass is under tension, it can crack at any time, especially when driving on a bad road. The only exception to the rule is windshields manufactured in the city of Bor.
Such glass has been installed on factory VAZ models for several decades and has never caused any complaints.
Glass from Asian manufacturers, Turkish and Chinese, is currently the cheapest. Naturally, the price can judge their quality. During production, glass is used without any additives, due to which they do not withstand impact well, and during long-term use they are “rubbed” with brushes, and the working area can become matte after a year or two.
It is also quite common to come across glass with irregular geometry that simply will not fit into the opening, or with distortion. Such distortions are difficult to determine visually; they become visible only while driving, when the picture behind the glass changes dynamically.
When pressing two layers of glass, air bubbles may remain between them and the film, or some places may not be bonded well enough, which leads to peeling of the film and the appearance of spots on the glass that differ in color.
By the way, many service stations that replace glass do not undertake to install Chinese or Turkish glass, or do not provide a guarantee for the installation.
Original glass is no different from glass from European manufacturers in terms of quality, although they are slightly more expensive.
Which glass to buy is a personal question for everyone. Before choosing glass, you need to analyze how often you use the car and whether you intend to sell it. If you approach the issue of choosing glass thoughtfully, you can save not only your money, but also time.
Most common reasons
It is worth noting that the heated rear window most often does not work in a VAZ-2115 car for the following reasons:
Fuses blow out quite often. This usually happens unnoticed by the car owner.
As a result, one or another device stops working.
For this reason, you should pay attention to them first of all if you do not want to join:
Replacing them with serviceable ones will solve the problem completely. In other cases, it will also be necessary to clean the terminals of dirt, and at least visually make sure that the power wires have not come off the buttons. If the relay is faulty, then it will need to be replaced - it is not very expensive and is quite easy to install.
How to choose
Don't buy cheap copies. Products with a suspiciously low price are either made of low-quality materials or are sold as disassembled parts. An inexpensive consumable will require replacement after just six months of use.
It is advisable to find an original spare part. It will definitely fit the car, and the quality will be higher than that of its analogue.
Inspect the part carefully. The surface must be smooth, without scratches, even and transparent. The reflection must be clear and clear. If it is cloudy, do not rush to shell out money.
Check markings, manufacturer and type. Information must be clearly written. Blurred markings are one of the main signs of a fake.
The price of consumables ranges from 1000 to 3000 rubles.
Economy segment
Xyg (China) - the best Chinese parts on the market. Pass ultraviolet rays. The material is not of the best quality: poor visibility, the image is distorted. Weak structure. This consumable will have to be changed twice a year. Overall, the price is reasonable.
Borovskoye KMK (Bor, Nizhny Novgorod region). The spare part is made of soft material, chips and scratches quickly appear. Doesn't take punches well. Cheap, but short-lived.
Premium segment
Pilkington (UK). European quality. Resistant to scratches, chips do not appear the first time. Will last a long time.
Borovskoye AGC-glass (the plant was purchased by the Japanese Company AGC-Glass). Decent choice. Japanese quality, quite high price. The company provides energy-saving, multi-layer shock-resistant and colored lacquer-coated glass.
Types of damage
There are 2 main types of damage to car windshields: chips and cracks. Chips are small, most often located at the edges, areas of destruction of one of the triplex glasses (usually the outer one). You can operate a car even if there are a large number of chips without urgently replacing the glass.
In turn, cracks are through-cut damage that has a longitudinal or branched shape. They can appear even from a small pebble, but, regardless of their size, they pose a serious threat. Thus, over time, cracks in the glass can increase, gradually occupying an increasingly larger area, which can ultimately lead to a weakening of the glass surface and its complete loss.
Considering that this can happen even while driving, it is worth understanding that the only solution when cracks appear should be to replace the windshield (and, if necessary, replace the rear window of the VAZ 2114).
It is worth noting that in some cases (for example, when the crack occupies a small area), temporary measures can be taken to prevent its increase, which will allow you to use the car for some time without replacing the glass.
Such measures include:
All of the above measures should be temporary, because even if the crack stops spreading or is not visible at all (as a result of sealing), the surface of the glass will still remain damaged, as well as the risk of it falling out over time.
Causes and consequences of damage
Driving on poor quality roads in Russia forces car owners to look for a new windshield at least once every year and a half. Even a very small pebble flying from under the wheels of a car can lead to damage to the part.
There are two types of damage:
- Chips. If only a chip appears on the surface, the driver is lucky. This means that the first layer is damaged; it is not necessary to install a new spare part.
- Cracks. You can't hesitate. At any moment, glass can crumble into pieces due to a hole in the road, and this will lead to an accident.
What can you do
If the driver fails to change it in time, there are several popular tips:
- Using a glass cutter, make perpendicular cuts 0.5 cm long along the edges of the “web”.
- Drill small holes with a thin diamond drill bit. The work requires accuracy, patience and attention.
- “Weld” the crack. It's better to contact specialists. Without experience it will be difficult.
Replacement
There are two options for replacing the windshield on a VAZ 2114:
Contact a car service. Fast, simple, but expensive. On one's own. If you have experience in repair work of this kind, time, patience, and an assistant, then dismantling is possible in your own garage.
How to remove
The work begins with the fact that we remove all unnecessary things. Side trims, wipers - this interferes with dismantling. Now we remove the old glass: starting from the top corner, squeeze it out along with the rubber. It is advisable to have someone help. If you pry the seal with a flat screwdriver from the inside, it will be easier to remove the headband.
You need to work with gloves, taking safety precautions.
Clean the grooves. The replacement now needs to be replaced with a seal. If the rubber is cracked, it is also advisable to replace it.
How to replace frames and seals
Replacing the windshield frame requires more effort, but this operation can be done at home.
We measure the frame. Its width is 680 mm in the center and 1378 mm diagonally. Further actions:
The seal needs to be replaced as it wears out. If it has shrunk in places and lost elasticity, then it is advisable to install a new one in the near future. To replace the front window seal of a VAZ 2114 you will need:
To make installation easier, apply lubricant to the rubber seal and soap solution to the lower groove. You need to put a thin, strong rope inside the seal. Place the new seal on the glass. We pull the ends of the cord in the center of the bottom of the material. It is advisable to soak the cord with detergent.
How to reinstall a VAZ element
If we describe the replacement of the rear window on a VAZ 2106, then we must take into account that the “six” does not have window heating. To work here, in addition to an assistant, we need:
- flat screwdriver;
- blanket;
- nylon cord 5 m;
- soap solution, brush.
Also read about repairing a crack in a car windshield and replacing a rear engine mount. Begin.
- From the trunk side, use a screwdriver to pry up the trim trim in each of the lower corners and remove it.
- We remove from the inside, in the cabin, all decorative trims covering the edges of the window.
- Starting from one of the lower corners, bending the seal with a screwdriver, gradually squeeze the glass out along with the seal. The bottom corner of the window is released first, and then everything else.
- We pull out the glass by the bottom and side parts. Having taken it out completely, remove the seal from the middle to the edges.
- We inspect the seal and also clean its drainage holes with a screwdriver.
- We put the seal on the new part removed from the blanket, first moving along the bottom side, then along the side, then along the top side and again along the side.
- We insert the rope into the groove of the seal intended for the edge of the body along the entire perimeter, and at the end of the process there should be ends of the rope of 20 cm each.
- We coat the upper part of the seal and the edge of the body on which the rubber element will be placed with a soap solution.
- We place the part of the window where the ends of the rope come out onto the edge of the body. The assistant goes into the salon and begins to carefully pull out the ends of the rope. At the same time, we press on the outside and tap on the glass with our hand. As a result, the window should sit in its place along with the seal.
- We put everything that was removed back in place.
This is the process for the Six. And here's how to replace glass on a VAZ 2109. We remind you that this car has a fifth door at the back. To carry out the work, again with an assistant, take the following:
- flat screwdriver;
- white spirit, rags;
- tight rope 5 m;
- soap solution.
Begin.
- Having removed the windshield wiper, insert a screwdriver a maximum of 5 mm, bend it back and take out part of the seal. We repeat the procedure around the entire perimeter with caution. We take out the rubber element in this way in parts, since it is very fragile!
- Disconnect the heating filaments.
- Carefully remove the window.
- We degrease the edges of the new element prepared for installation with white spirit.
- We put the seal on our new body part - from the corners to the sides.
- Next, we insert the so-called lock - we insert a shiny part with a wedge profile around the entire perimeter into the seal. Lubricate the seal groove intended for the body with soapy water.
- Now we act according to the already studied scenario. Insert a rope into the groove of the rubber element. An assistant from the interior gradually pulls it out, while at the same time pressing from the outside along the glass surface. Initially, you can completely place the bottom of the window into the opening, and do not insert the rope into the lower part.
- At the final stage we turn on the heating.
What to do with the same part of foreign cars
Now let’s discuss the same operation in relation to some popular budget foreign cars. To replace the rear window of Renault Logan we will need:
- screwdriver;
- awl;
- knife;
- string;
- gluing kit;
- masking tape.
This car has a glass element glued into the body, so we proceed as follows, again with an assistant.
- We detach the interfering decorative elements.
- We pierce the glue seam with an awl.
- We insert a string into the hole formed.
- Next, together with an assistant located inside the cabin, we pull the string along the entire perimeter of the window.
- Carefully remove the dismantled part.
- Cut off the old seam, leaving about 1 mm of glue.
- Next, we treat the edge of the window and the edge of the opening with the activator, and then with the primer from the kit.
- We install rubber pads around the perimeter.
- After waiting half an hour, apply the adhesive composition to both edges.
- We install the window in its normal place.
- We glue it with masking tape until the glue dries completely (about 3 hours).
- Remove the tape. We install decorative elements.
- Turn on the heating. By the way, we automatically replace the broken rear window heating, since the new part is already equipped with working heating threads.
At this point the procedure can be considered complete. As you can see, it is radically different from the technology described for the VAZ. It's all due to the method of fastening. By the way, it is also used by Daewoo Matiz.
However, gluing the transparent element of the Matiz’s rear door is even easier than that of Logan – the amount of work is less. But car enthusiasts are often worried about another problem - replacing the rear window heating button on a Matiz. The fact is that these machines do not have a heating relay, so the button often fails. So, rather than constantly replacing a broken rear window heating button, it is better to install a relay inside the circuit. To install it, just study the video on replacing a broken heated glass relay on similar cars.
At the same time, replacing the rear window washer nozzle on such cars is often carried out simultaneously with reinstalling the window, since the washer is located directly on the wiper. By the way, the windshield wiper must be removed before removing the window.
Inserting new glass
We start by applying a rubber seal to the new glass. Then we put another rubber band in its place, which is called a lock. It is done brilliantly so that drivers know. Why is the lock applied before the glass is installed, and not after? Because it’s faster and, as practice shows, more convenient. After installing the lock, the most important thing begins - installing the rear window in its place. To do this, we need a cord about two meters long (in general, it’s better to prepare a cord, a screwdriver and a friend to help you ahead of time).
We insert the cord into the groove of the seal, but not the entire length, but only onto the top and sides of the groove. The remaining ends of the cord should be approximately the same length. Then we take the glass and insert it into the lower groove, as if rubbing it in, so that the seal lies evenly in place. Then, calling a friend for help, we begin to press on the glass, while simultaneously pulling the cord out of the groove. At the same time, the cord pushes the sealing rubber aside and allows the glass to gradually take its place.
This operation should be done slowly, pulling the cord alternately from the right and then from the left. When the cord is pulled out completely, the glass with rubber bands will completely fit into its grooves. And this will mean that everything worked out for you.
How to put
During installation you will have to resort to outside help. The glass is inserted into the lower groove, and only then carefully around the entire perimeter. As you insert the windshield, pull out the cord to fit the seal tightly and efficiently.
Be careful when pulling the rope at bends! In the side parts it slides with difficulty and can tear; press harder from the outside of the car.
It is advisable to fix the rubber with glue-sealant, and attach the glass to the roof and sides with tape overnight.
Replacing the rear window of a VAZ is carried out in the same way. If you installed a windshield, you can install this, although removing the rear window is a more difficult task. To insert the rear window, ask a friend for help, as you will have to pull the rope and press on the consumable at the same time.
Replacement of side glass on VAZ 2113, VAZ 2114, VAZ 2115
Side glass performs important functions in a car:
Note! You will need the following tools: a screwdriver, wrenches or socket wrenches, and new glass. We remind you that take the new glass together with the frame, otherwise, if you buy it separately, you will be tortured by installing the frame on the glass and aligning it.
Clip location
Placed at the bottom center (indicated by the blue arrow, and the glass is shown by the red arrow). The frame is inserted into the glass, over time it weakens and there are even cases when the glass fits askew into the door. The weakened clip does not hold the glass; it dangles in the door. The glass is attached to the window lifter using this clip. In general, the detail is necessary and irreplaceable. In the event of a fault, there are two options:
When should you replace your side glass?
In principle, the time of replacement is a personal matter for each owner. Some people change glass for aesthetic reasons, others because of damage. However, there are a number of recommendations:
Search
rear window replacement
Rear window The car is a real assistant for the driver. It is through him that we see what our client can do, what is happening behind us, and correctly assess the situation. However, glass is a very fragile material, and if a stone or other loose object gets caught in it, it can crack or shatter into a large number of small pieces. For a temporary solution, of course, cover the gap with a thick film. But this, of course, is not an option. In the future, the rear window will need to be replaced.
The car owner may have postponed this work until later, fearing serious expenses. In fact, our client is left to do everything possible to find the funds to purchase new glass and glue. The rest of the work is completed independently within 1-2 hours.
Replace the rear window on a VAZ-2109
Before you go to the store differently in the market and get a new rear window for your car. It is important that it fits your model correctly (pay special attention to heating and design features).
It is best to work in a well-lit area with sufficient maneuverability. If the weather outside is perfect, you can stay right next to the garage. Helping your partner replace the rear window is highly desirable. It is difficult to cope with such work without outside help.
What you need after the previous steps, start specifically. There are three steps here:
Removing glass from the trunk lid 2109 2114
Conventional glass
even a schoolboy can control the trunk lid.
Removing the rear window on a VAZ 2109 from Seryoga)))
Is it correct to remove the rear window
When doing the work, be very careful not to touch the surface. car body (otherwise you will have to restore it).
When the old glass fails to take off , do not rush to “sculpt” a new one right away. It is better to perform some of the necessary manipulations:
Before installing the lock, it is better to pull it a little. Otherwise you won't like its length. The wedge installation is done like this. Install the long section first and the small section at the end. In this case, some part of the wedge remains unused; it is better to cut it. Otherwise it will interfere with future work.
When should new glass be installed? There are two options. the old glass is damaged or you decide to glue a shadow. At the beginning, our client remains clear. do without a change. In this case, we are talking about tinting; it is better to do this work without disassembling. Practice shows that it is almost impossible to remove the rear window without damage.
Before installation, prepare a thick piece of rope. It is advisable that the length of the rope exactly matches what was left for our client on the side of the rear window. Pay special attention to the quality of the rope. he must become strong. If it breaks during operation, it will be difficult to remove the broken piece from the seal.
What you need to do is:
The final shrinkage of the glass occurs within 3-4 days. This is facilitated by vibrations that are inevitable when moving.
Conclusion
Replacing side glass on a VAZ 2113-VAZ 2115
Removal
1) The glass on the front and rear doors is removed in almost the same way. We will look at both options, but start with the front. You will need the help of an outsider. Have a helper hold the glass to prevent it from falling. And you lift the glass all the way up and unscrew the bolts securing the window regulator to the glass frame. Just in case, we will analyze the situation without an assistant. Then, at the beginning of the operation, the side glass is blocked with a screwdriver, preventing it from falling (photo 1), then the door trim is completely removed (read more in the article: “Replacing a door on a car”, from point 1 to point
and remove the two bolts securing the clip to the window lifter (photo 3). After unscrewing the bolts, carefully begin to remove the seals in the door in which you are replacing the glass (photo 2). Please note that you will have to remove the screwdriver to remove the seal from the glass, remove it carefully and hold the glass. After the operations have been completed, tilt the glass to the side and remove it (shown in the fourth picture).
Note! When working with an assistant, there is no need to insert a screwdriver. Immediately remove the seals from the door and unscrew the cage bolts, and let an assistant hold the glass. After unscrewing the bolts, roll the glass on its side and remove it from the car door!
2) With the rear doors, the procedure is similar: insert a screwdriver, remove the trim from the door and unscrew the two bolts (photo 3) of the cage. Then the rubber seals are removed from the door (photos 1 and 2), the glass is rolled on its side and removed from the car door (photo 4).
The new part is installed in the reverse order of removal. If you bought glass without a frame, you will definitely have to install it. Take soap or WD-40 and coat the inside of the clip, then install the clip on the glass. Place the glass in the sun to dry quickly. Be sure to monitor the drying process, wet lubricant will not hold the clip, it will be removed from the glass and it will fall.
Additional video Attached below is a video on today's topic using the example of cars of the Samara and Samara 2 families, we recommend that you watch it.
Rear door of VAZ 2109
In order to remove the rear door on a VAZ 2109, follow these steps:
Open the door and remove the two bolts securing the limiter bracket to the B-pillar
Unscrew the two bolts securing the upper and lower door hinges to the B-pillar and remove the door. Installation of the VAZ 2109 rear door is performed in the reverse order of removal. Before final tightening the bolts securing the hinges to the B-pillar, close the door and position it so that the gaps in the openings around the entire perimeter are the same. Then carefully open the door and finally tighten the fastening bolts.
Replacing the window regulator and glass on a VAZ 2109
In order to install the rear door glass on a VAZ 2109 or replace the window regulator, follow these steps:
Lower the window all the way down and remove the rear door trim in the same way as removing the front door trim. The photo shows the location of the rear door trim mounting pins
When should you replace your door window regulator?
If we are talking about an electric window lifter, then as a rule, when it fails, the glass stops going up and down when you press the corresponding button, in addition, on some cars (you most likely have already paid attention to this) it happens that the glass somehow goes down (Slowly ) and almost does not rise (you have to help with your hand), this also indicates that the window lifter has become unusable and requires replacement, but by the way, in some cases, due to the fact that the glass does not rise and fall poorly, it may not even be the window lifter itself that is to blame glass, it’s just that over time its fastening weakens and thus the glass becomes skewed, which is why problems occur with lowering and raising the glass on the car, but as for mechanical window lifters, everything is simple here, if by rotating the handle the glass has ceased to be adjusted, then the window regulator itself has failed and requires replacement.
Lada 21099 *Night Harpy* › Logbook › DIY rear window replacement
What is needed to install glass? How to glue glass? What glue should I use? In this article I will try to give you the answer - what and how to glue car glass.
Installation of auto glass on all cars, without exception, is done in two ways: installation in a rubber seal and gluing the auto glass. Let me point out right away that there is no difference between the installation of car glass for foreign cars and domestic cars. And auto glass is cut and installed in the same way. The principle is the same.
Replacing the headlight glass
If you see that the headlight itself is working, and its cloudiness is due to glass defects, you need to know how to remove the glass from a VAZ 2114 headlight and then replace it.
The algorithm for performing the procedure is as follows:
The glass is now removed, but remember that reassembly will involve applying sealant (can be replaced with a rubber seal), so be sure to get some in advance. Also, some manufacturers' headlights have headlights with clips, so don't use brute force, just look where they are and tighten them.
Didn't find the information you are looking for? on our forum.
We recommend reading:
Installing the ignition on a VAZ 2107 carburetor, marks, gap in breaker contacts, checking ignition
The battery light is on on the instrument panel of the VAZ 2110, reasons and how to fix it
How to change brushes on a VAZ generator
VAZ 2110 brake system, operating principle, possible problems and their elimination
VAZ 2107 carburetor troits at idle
How to fix VAZ 2107 bridge humming
How to change pads on a VAZ 2115
What are the best racks for the VAZ 2114. Types of racks
Glass color
The windshield can be either transparent or tinted. Such tinting does not contradict any rules, it is completely legal, and is simply not visible to an ignorant person. But during operation, slight darkening reduces the effect on the eyes of the bright light of headlights of oncoming cars.
It is also more comfortable to drive with such glass on sunny days. The tint color can be blue or green. In order to clearly see the color of the glass you are purchasing, it is enough to attach a sheet of paper to the back of it - its color will change depending on the color of the tint.
There are also glasses whose polymer film contains special substances that reflect ultraviolet rays. Ultraviolet radiation is not visible to the naked eye, but it has a destructive effect on the retina, causing vision impairment.
Such windshields are often installed on fully equipped vehicles or as an additional option. Externally, a car with such glass can be identified immediately - the windshield has a slight purple tint.
The windshield may also have a decorative strip along its upper part. The color of such a strip is usually green or blue, and its light transmittance varies depending on the manufacturer.
How to change the rear window of a car with your own hands
Of course, it's not often that a car's rear window cracks. But still, many car enthusiasts are worried about such a breakdown. After all, sometimes they have only one option left - replacing the rear window. We list the situations in which it is necessary to replace the rear window:
Next, we will consider several cases of replacing a defective rear window, applicable to both domestic and imported cars. Let us first note that with this repair there are certain difficulties associated with the rubber seal or the adhesive seam.
Rear window replacement
Replacing the rear window of a VAZ 2109
You can replace the rear window of a VAZ 2109, as mentioned above, yourself. Before installing new glass, you must remove the old one.
Removal
To do this, you should:
- Take a screwdriver and insert it into the seal that holds the glass. It should be inserted approximately 5 mm.
Note: it will be possible to insert the screwdriver deeper, but you should not do this, as you may make a hole that is too deep.
- Carefully move the screwdriver a few cm. Tear off another piece of the seal.
- Step by step you can get rid of everything.
Note: since the glass is secured with a seal, as soon as it is gone, it will begin to wobble. Therefore, you need to get rid of the seal slowly and carefully so that the glass does not fall out before it is needed.
- After the seal has been removed to the upper side corner, you can begin to remove the glass itself.
Replacing glass on a VAZ 2109
Don't try too hard when removing the glass. Usually it cannot be kept completely intact.
It certainly cannot be reused. The main thing is not to damage the body of the vases, otherwise additional repairs will be required.
Preparing for installation
Before you begin installing new glass, you must do the following:
- Wipe the edges with degreaser to make it easier to install the seal. That is, the cleaner the glass, the better the seal will fit.
- Put on the seal. First, it is distributed in the corners, and then pressed against the sides of the glass.
- After this, you should install a lock, which is a small wedge that looks like the letter P. It needs to be inserted so that it is in the center of the seal, but runs along the entire perimeter.
Note: The wedge should be stretched slightly before installation. If you don't do this, then there simply won't be enough. Usually you can stretch it up to 20 cm!
Installation
Replacing glass on a VAZ 2109
Installing the rear window may be necessary when replacing it, or when tinting it. Although usually, tinted glass is new, since, as stated earlier, it is almost impossible to remove the rear window without damaging it. In order for the installation to be completed successfully, you should find a rope that is long enough to completely surround the sides of the rear window. It should be quite tight, since it cannot be allowed to tear. If part of the rope remains in the seal, it will be very difficult to pull it out. Installation of a new rear window should be done as follows:
- Determine where approximately the middle of the rope is. Insert this part into the upper side of the seal.
- The seal has two grooves. You need to find the one that is closer to the top of the glass.
- On the opposite side, you should also insert the rope until it intersects with the end of the previous rope.
- When they intersect, the end of one must be placed on the end of the other.
Note: the ropes must overlap each other. The overlap should vary between 5-10 cm.
- The free ends of the rope should be pulled into the cabin.
- Only after this can glass be placed in the opening. It is advisable to have someone help, as it is quite heavy and can be accidentally dropped. The bottom of the opening should fit into the outer groove.
Replacing glass on a VAZ 2109
- You need to press lightly on the glass. At the same time, it should press even better into the seal. In addition, this way it will sit in its place much better.
- The rope should be pulled towards you from both sides (as if you need to tie a knot).
- Stretch half the rope to the bottom corners of the glass.
- After this, smoothly seat the glass.
- To make it easier to pass the left corners, you need to “twist” the rope clockwise, and the right corners – vice versa.
- While pulling the rope, you need to carefully seat the glass in the opening. There is no need to hit the glass, as it is still sitting very precariously, so it may fall out.
Usually the glass shrinks to its maximum after 3-4 days of driving. This is facilitated by the constant vibrations that the car undergoes while driving. If you want to save time, you can take the car to a car dealership, where the price for this work will be rather high. However, you can carry out repair work yourself and at home. Of course, before this you should review various photos and videos on this topic. And if you come across instructions somewhere on the Internet, you should not neglect them.
You can also learn about windshield replacement on our website.
Add a commentAdd a comment We recommend readingHeated rear window of a VAZ 2110: design and repairReplacing the rear window of a VAZ 2109: how to do it correctlyRemoving the windshield of a VAZ 2109:how to do it correctlyVAZ 2109: replacing a window lifter on your own
Of course, it's not often that a car's rear window cracks. But still, many car enthusiasts are worried about such a breakdown. After all, sometimes they have only one option left - replacing the rear window. We list the situations in which it is necessary to replace the rear window:
- consequences of a traffic accident;
- a stone flying from under the wheels of a speeding oncoming car created a very large crack on the highway;
- reinstallation of a standard window with a similar one from another modification of the car;
- Body repairs are being carried out, while the glass element interferes with the work.
Content
Next, we will consider several cases of replacing a defective rear window, applicable to both domestic and imported cars.
Replacement timing and choice of optics
The last two elements have a shelf life directly related to the material from which they are made and the methods of car care. At the same time, even the best of them are still susceptible to the ingress of dirt associated with depressurization of the headlight structure.
The choice of headlights is extremely important for the convenience of the motorist. To be more precise, it is not the manufacturer itself that is important (although it affects the characteristics of the light), but the identity of the lighting fixtures. If your car has standard headlights, but you decide to replace only one, then find the original ones. You should not take AUTO SVET or BOSCH, which are similar in appearance.
From a technical point of view, the headlights will be the same, but the manufacturing technology of the optics differs from one company to another, and as a result, you will get two distinctly different headlights. Even if you don't care about the appearance of the car, don't forget about the properties of your eyes.
Human vision and the brain have a number of characteristics, and in this case they will manifest themselves in the fact that a more powerful headlight will create a “twilight zone” instead of a dimmer light. Consequently, there will be no improvement in visibility, and the brain will perceive the “blind spot” almost the same way if it did not exist at all.
Removing old glass
You should start replacing the rear window in VAZ cars with the grooves of the seals. To do this, you will need a flat blade screwdriver to pry the seal lock from the inside of the glass. After which we simply pull it out.
Then, using a screwdriver, move the frame seal as far as possible from the outside of the glass. After which, we do the same on the inside of the frame. Having freed the glass, we begin the extrusion process. Why do we call for help from a friend smoking on the sidelines and ask him to hold the glass from the outside. We ourselves squeeze out (push carefully, but with force) the rear window from the inside.
You may not be able to free the glass from the frame the first time. There is no need to despair and freak out, but it is worth going through the seals with a screwdriver again. Then try again to squeeze out the glass. It will still resist, but eventually it will pop out. Having briefly rejoiced at this circumstance, we proceed to installing new glass.
Source
Removal instructions
Disassembled door
If you don’t know how to remove the window lifter handle, don’t despair, it’s easy to do. Before removing the mechanism, you need to remove the trim from the door. Then be sure to disconnect the wire block and the power window connector. Then remove the three nuts that secure the mechanism to the door. Next are two bolts that secure the lift and the glass itself.
Dismantling process
Then, lift the glass to the very top and fix it, you can use a screwdriver or ask someone to hold it. But it’s better to pull it out, because otherwise there is a risk that the glass may break.
To completely remove the mechanism, you need to additionally remove the door handle. To do this, unscrew its two screws and push the handle inside the door. Then, you will need to disconnect the rubber holder that holds the rod on the handle. Once you're done with this, you can pull out the handle, and then the window regulator itself through the same hole. Now you know how to remove the window handle and the entire mechanism.
