Do-it-yourself replacement of a Priora hand brake

Since ancient times, some Taz drivers used first gear to prevent the car from rolling away, even with a handbrake, my dad always taught me to set the speed. But this can end badly if you don’t turn off the speed and start the car. Over time, the parking brake, due to constant use, stretches the cable, you can tighten it a limited number of times, then you have to remove it, because tightening it is already useless.

He stops holding the car and is not fixed. You can tighten the handbrake on the Priora with just two 8 keys in the hole. This is usually done in your garage. Replacing the drive and handbrake cable on a Priora will require additional keys. Of all the brake systems of the Priora car, the parking one stands out separately. It saves you from unpleasant surprises - while it is working, the car will not roll away in the parking lot. When the handbrake doesn't hold, you should start repairing it right away, maybe you just need to tighten it. Lada Priora received the part as early as 2108 - it has not been changed since then.

When the driver raises the handbrake handle higher and higher to hold the car in place, this indicates that the parking brake system is not working. Most often this can be solved by tightening it, just tighten the cable and the handbrake will hold. There may be several malfunctions in the parking brake system of a Priora car; read the article to the end and find out about them.

Handbrake (parking brake) on Priora - article number and price

The assembled parking brake system of the Priora car has the catalog name “Handbrake drive” - number C170. Main components:

• cable bracket: 2108-03508214-20, 30 rubles;
• handbrake cable: 2110-03508180-01, price - 400 rubles;
• parking traction axis: 2110-03508073-00, price - 500 rubles;
• laying of parking rod 2110-03508089-00;
• parking drive rod: 2108-03508089-00, price - 250 rubles;
• parking brake lever (assembled): 2110-03508012-00, price - 600 rubles. Button – 2110-03508039-00;
• lever assembly with rod: 2110-03508010-00, price - 1300 rubles;
• traction protective cover: 2108-03508046-00, price – 40 rubles;
• cable equalizer: 2108-03508075-10, price – 50 rubles.

Basic faults

According to the law, a malfunction of the handbrake is accepted in two cases:

• If, at a 16% slope, the handbrake does not hold the equipped car (without cargo and passengers, but with a full tank of gasoline, the driver’s weight is taken to be 75 kg).
• If, on a 23% incline, the handbrake does not hold the vehicle at full load (the maximum permissible vehicle weight has been reached).

In reality, more often than not, a malfunction of this brake mechanism of the Lada Priora is noticed not by measuring the steepness of the slope, but by clicks. When another click of the handbrake is added to the usual “set of sounds” when leaving the car, every car enthusiast understands that it’s time to tighten the cable.

But the problems don't end there. For the parking brake system they can be as follows:

• The cable has stretched too far. Over time, it undergoes deformation. It can be tightened, but to a certain extent.
• The cable broke. When the “limit” is reached, the mechanical device will have to be replaced.
• The handbrake indicator on the dashboard does not light up or go off. This is due to the sensors.
• The lever button is stuck.

Product delivery options

Note! Below are the shipping methods available specifically for this product. Payment options may vary depending on the shipping method. Detailed information can be found on the “Delivery and Payment” page.

Parcel by Russian Post

Available payment methods:

• Cash on delivery (payment upon receipt)
• Using cards Sberbank, VTB, Post Bank, Tinkoff
• Yandex money
• QIWI
• ROBOKASSA

Shipping throughout Russia. Delivery time is from 5 to 12 days.

Parcel by Russian Post 1st class

Available payment methods:

• Cash on delivery (payment upon receipt)
• Using cards Sberbank, VTB, Post Bank, Tinkoff
• Yandex money
• QIWI
• ROBOKASSA

Shipping throughout Russia. Delivery time is from 2 to 5 days. More expensive than regular delivery by Russian Post, approximately 50%. Parcel weight up to 2.5 kg

Express Parcel EMS

Available payment methods:

• Cash on delivery (payment upon receipt)
• Using cards Sberbank, VTB, Post Bank, Tinkoff
• Yandex money
• QIWI
• ROBOKASSA

Shipping throughout Russia. Delivery time is from 3 to 7 days. More expensive than regular delivery by Russian Post, approximately 100%.

Transport companies

Available payment methods:

• Using cards Sberbank, VTB, Post Bank, Tinkoff
• Yandex money
• QIWI
• ROBOKASSA

Delivery is possible to any locality where there is a representative office of the transport company. Delivery time is from 2 to 10 days. Sending large parcels is approximately 50% more profitable than by Russian Post.

Pickup from our warehouse

Available payment methods:

• Cash upon receipt
• Credit, installments
• Using cards Sberbank, VTB, Post Bank, Tinkoff
• Yandex money
• QIWI
• ROBOKASSA

Pickup times must coincide with store opening hours.

Any Lada model that has ever rolled off the assembly line of the Russian auto giant AVTOVAZ has a plastic handbrake handle. The fact is that AVTOVAZ never used other materials to design this part. Why? The fact is that domestic Lada cars have always been in the so-called budget segment. And here the cost of each part and its wear resistance are very important. And the point is not that leatherette quickly becomes unusable. Bad leatherette quickly becomes unusable. But the use of a good one is prevented by another limitation of the manufacturer - the final cost of the part.

How to change the handbrake on a Priora - step-by-step guide

Replacing the handbrake cable is needed when a regular tightening is no longer an option; you will have to change the cable or drive. In order to replace the cable on a Priora car, prepare a Phillips screwdriver and a set of keys.

Replacing the cable is carried out as follows:

1. Place the car in the pit, lower the handbrake, and engage the gear.
2. Jack up the rear of the car, put supports on it, and remove the wheels. Further actions will be described on one side, they will need to be repeated on the other side.
3. Loosen the main muffler and hang it up. Do the same with the resonator.
4. Slightly loosen the handbrake rod locknut. Remove the cable equalizer.
5. Remove the cable end by pulling it through the special bracket.
6. Remove the brackets that hold the cable in place.
7. Using a screwdriver, press down on the actuator lever to move it further away from the brake pad. The lever should move to the forward position. After this, you can disconnect the cable tip from the brake lever.
8. Loosen the nut on the rear beam that holds the cable, and then pull it towards you.
9. Pull the cable through the bracket that is attached to the body, then through the brake shield.
10. Check the parking brake and make adjustments. If necessary, tighten the nut more.

In order to change the Priora handbrake lever, you will need a set of keys, pliers, and a Phillips screwdriver.

Removing elements of the parking brake system

We replace the parking brake cables when they are broken, pulled out, or stuck inside the sheaths, when adjusting the parking brake fails to keep the car stationary on a slope - up to 25% inclusive. We remove the parking brake lever to replace it or to replace the lever rod. The cables should be replaced simultaneously - left and right. We show the replacement of the left cable. Move the parking brake lever to its lowest position. We unscrew the locknut and the adjusting nut from the parking brake lever rod (see “Adjusting the parking brake”).

How to remove the handbrake lever. General leadership

1). Parking Brake Components.

2) . Remove the top panel of the console . Using a screwdriver, release the 4 latches and remove the top panel of the console. Remove the rear end panel of the console. Remove the glove box on the console. Remove the cover.

3) . Glove box mounting bolts . Remove the 4 bolts and remove the glove box.

4) . Remove the parking brake lever . Unscrew the locknut and the adjusting nut. Remove the 2 bolts and remove the parking brake lever. Raise the lock. Disconnect the parking brake cable from the lever. We unscrew the screw and remove the parking brake sensor assembly.

How to remove the hand brake lever on a VAZ 2114

1). Set the lever (1) to its lowest position.

2). Disconnect the cable ends (10) from the levers (13) of the manual drive of the shoes and from the equalizer (6). To do this, unscrew the lock nut (9) and the adjusting nut (8) from the rod (5).

3). Then remove the washer (7) and equalizer (6).

4). Having taken out the cotter pin and axle (12), remove the washer (14), lever (13) and release bar (15) of the pads.

practical guide

The need to replace the parking brake cables arises if the cables, as a result of corrosion, have lost the ability to move in the sheath, have become very stretched, or have broken threads.

If it is necessary to replace one of the cables, we also change the other cable.

Removing the parking brake cables:

1. We prepare the car for work.

2. Remove the brake drums.

3. Remove the protective screen.

4. Remove the rear protective screen.

5. Loosen the locknut of the parking brake lever stroke adjusting nut and unscrew the locknut.

6. Using a socket wrench with a 13 mm deep head and a cardan joint, unscrew the adjusting nut and remove it from the rod.

7. Remove the adjusting rod cable equalizer.

8. Disconnect the cable ends from the equalizer.

9. At the brake mechanism of the left rear wheel, use a large slotted screwdriver to move the spacer lever forward and remove the cable eyelet from the hook of the spacer lever.

10. Using a 10 mm spanner, unscrew the nut of the bracket securing the cable to the left arm of the rear suspension.

11. Remove the front cable end from the hole in the body bracket.

12. Remove the cable from the two brackets securing it to the underbody. 13. Remove the cable from the rear suspension beam bracket. 14. We take the cable out of the hole in the support shield of the rear brake mechanism and remove it.

How to remove the handbrake lever on a VAZ 2109

1). From the bottom of the car, unscrew the locknut and the equalizer adjusting nut.

2). Remove the equalizer from the lever rod.

3). Remove the protective cover.

4). Remove the protective cover of the gear shift lever from the floor tunnel lining.

5). Remove the floor tunnel lining.

6). Remove the floor tunnel lining by sliding it back.

7). Unscrew the four mounting bolts and remove the lever.

. Remove the retaining ring, remove the axle and disconnect the rod from the lever.

9). Unscrew the button and remove the pawl spring. You just need to do this carefully, since the force of the compressed spring acts on the button.

10). Reinstall the lever in the reverse order of removal.

Reviews

Delivery of goods is carried out throughout Russia and the CIS:

1. Russian Post (from 350 rubles and above)

Delivery to all regions of the Russian Federation and CIS countries

2. Transport Companies (from 350 rubles and above)

Delivery throughout Russia and the Republic of Kazakhstan

• TK Energy (nrg-tk.ru)
• TC Business Lines (dellin.ru)
• TC SDEK (www.cdek.ru)
• TK PEK (pecom.ru)
• TK KIT (tk-kit.ru)

3. Pickup

The order can be picked up at the office at Tolyatti, 40 Let Pobedy 38, TD “Malachite”, 1st floor.

The waiting time for sending an order in our online store is approximately 2-7 working days, large orders 7-14 working days. days; color of bumpers, mirrors, body parts, spoilers, etc. 7-14 work. days; sewing covers, upholstery, steering wheels, gear knobs, EVA mats, etc. 7-14 work. days.

During this period, we will send you a tracking number by email. email to track the parcel en route.

Payment can be made in the following ways:

1. Payment to a Sberbank card

You can pay using the SBERBANK-Online application and other Bank applications.

After placing an order, making payment, do not indicate comments , we ourselves will understand by the amount of the order and the name of the sender. After receiving the funds, the status of your order will be changed to paid until 17.00 of the current day, or from 9.00 of the next Moscow time.

2. By bank card

Automatic acceptance of payments using MIR Bank cards, VISA International, Mastercard.

How to remove the hand brake lever on a VAZ 2110

How to remove the hand brake lever on a Lada Kalina?

1). Remove the floor tunnel lining.

2). From the bottom of the car, unscrew the lock nut and the parking brake adjusting nut and remove the equalizer from the rod.

3). From inside the cabin, unscrew the screw of the front fastening of the parking brake lamp switch bracket.

4). Remove the 4 bolts securing the parking brake lever.

5). Remove the parking brake lever by removing the rod from the hole in the floor.

6). To replace the rod, remove the cotter pin (1) and the washer (2).

7). Remove the rod from the axle.

. Replace the worn or cracked plastic bushing.

Conclusion

As can be seen from the description, adjusting and replacing the parking brake is not the most difficult operation. Even a novice motorist can handle it. There is no point in tempting fate and risking life and health. There is no need to operate a machine with a broken unit. Preventative maintenance of the handbrake is carried out at least once every six months.

Perhaps you have successfully solved the problem of adjusting and replacing the brakes on the Lada Priora? Share your experience with our readers in the comments. Any information would be very helpful.

How to remove the hand brake lever on a Niva Chevrolet?

1). Disconnect the rear cable from the guide from the tip of the front cable.

2). Remove the floor tunnel lining.

3). We unscrew the 2 bolts securing the lever bracket to the floor and remove the lever.

4). Remove the locking ring of the lever axle.

5). We take out the lever axis.

6). We pull the cable inside the cabin.

7). Install the new cable and lever in the reverse order of removal.