Scher-Khan Magicar B: Instructions and manual in Russian

When using the Scher Khan car anti-theft system, there is often a need to reflash the remote controls or add new ones. The algorithm of actions is simple, so every car owner can set up the Sherkhan key fob independently.

One of the most common reasons for reprogramming Mobicar and Universe remote devices is loss or purchase of a new one. In addition, programming the remote control is required in the following cases:

commands are not issued from one key fob, the second one works fine;
damage to the housing or board of the remote control;
Damage to part of the liquid crystal display, which makes it impossible to monitor triggered security zones;
use of additional control panels. Occurs when purchasing a car with one key fob;
failure of the communicator and the control unit to work together.

Find out how to set the clock on the Sherkhan 5 key fob.

OPERATING MANUAL Alarm system…

Page 2

Image
Text

MANUAL

Vehicle Alarm System (VALS)

(hereinafter referred to as the system) meets the mandatory requirements in the system

GOST R certification required for car security devices:

GOST R 41.97-99 (Uniform regulations regarding official

approval of vehicle alarm systems

(STSTS) and motor vehicles in relation to their systems

alarm system (STS))

GOST R 50009-2000 (Electromagnetic compatibility of technical equipment.

Technical means of security alarm. Requirements and Methods

tests)

Thank you for purchasing a two-way car security system.

SCHER-KHAN MAGICAR B systems

Our company's continuous research and development embodies

the most advanced ideas and serve to satisfy all needs

users of our systems.

SCHER-KHAN MAGICAR B system

is a complex electronic

vehicle equipment. From its functioning and correct

installations depend on the safety of your life and the situation on the roads,

quality of work of nearby electronic equipment and

means of communication. Trust the installation of the system only to specialized

service stations.

During operation, periodically check the correctness

functioning of the system.

The manufacturer reserves the right to make changes to the system design

in order to improve consumer properties

SCHER-KHAN MAGICAR B

0.5 sec.
(factory setting) 2)
5 sec.
3)
45 sec.
4)
120 sec.

Programmable function 2-8: "Passive immobilizer"

This function enables a mode where every 30 seconds. after

When the ignition is turned off, the ignition lock will be activated. For

disabling the lock after parking for more than 30 seconds. should be briefly

press button II of the key fob.

This programmable function has two meanings:

Disabled (factory setting)
2)
Enabled

SETTING ALL PROGRAMMABLE FUNCTIONS OF MENU No. 2 TO FACTORY VALUES

To set factory default values for programmable functions, you must

complete two steps.

Entering programming mode. Press buttons (I+IV) simultaneously for 2 seconds. The siren will give one short signal, emergency

the alarm will flash once, thereby confirming successful

performing STEP 1 2)

Briefly press button III of the key fob three times. Each press will be confirmed by a short siren signal and a flash

alarm system. Some time after this they will sound

three siren sounds, the hazard warning lights will flash three times,

confirming the factory settings of all programmable

menu functions No. 2

Scher Khan 10 and 11

In order to program the Sherkhan 10, 11 remote control, read the following points.

Disable the security function. Turn the key to activate the ignition. Press any button on the remote control and hold for two seconds. The headlights should flash.
Within 5 seconds, press any key on the remote control. The lighting devices will blink twice if the alarm is not “password-protected”.
After five seconds the LED will stop flashing and turn on. This indicates that the main module is ready to bind key fobs.
Within 5 seconds, press the key on the pager. The same principle is used to link other devices. Correct action will be confirmed by flashing headlights.
To exit programming mode, do nothing for four seconds.

OPERATING GUIDE for programmable function...

Page 3

Image
Text

MANUAL

programmable function 2-7. In this case, the key fob display will show

label

(after polling the system status using a short

pressing button IV). The additional channel output requires

connect one or two additional relays to maintain

power supply to the ignition switch in TURBO mode. After this channel

activated, you can leave the car and put the system into

security mode. Ignition interlock and shock sensor, optional

sensor and ignition switch will be disabled. How

only the additional channel's operating time will end, immediately

the ignition lock and ignition switch will be turned on,

the shock sensor and additional sensor will be armed through

15 seconds. Also, this “additional channel” can be used for

maintaining power to the power window control buttons,

to allow the user to close the windows after switching off

ignition

Programmable function 2-6: “Pulse duration at the output of “additional channel 1”

This function allows you to set the pulse duration when

activating “additional channel 1”.

This programmable function has four meanings:

0.5 sec.
(factory setting) 2)
20 sec.
3)
60 sec.
4)
Trigger

When selecting the “Trigger” value, the signal at the output of the additional channel

can be turned on by command from the key fob - by short pressing the buttons

(I+IV), and it will be present until these buttons are pressed again. At

when this channel is activated by an event, the signal on this channel will be

be present until the end of this event (programmable function

2-4, values 2 and 3).

Programmable function 2-7: “Pulse duration at the output of “additional channel 2”

This function allows you to set the pulse duration when

activating “additional channel 2”.

This programmable function has four meanings:

SCHER-KHAN MAGICAR B

ATTENTION!

When purchasing, check that the warranty card is filled out correctly.

The manufacturer and system supplier are not responsible for

any disregard of the installation and operation manuals,

as well as for errors made during installation.

If problems arise with the operation of the system,

please contact the service center immediately for

diagnostics or consultation.

CONTENT

PURPOSE OF SCHER-KHAN MAGICAR B ………………………………………………………………..5

DELIVERY SET ……………………………………………………………………………………5

LIST OF FUNCTIONS……………………………………………………………………………….6

Functions of the key fob communicator………………………………………………………6

Functions of the processor unit………………………………………………………..7

TECHNICAL PARAMETERS ………………………………………………………………………………….8 KEY FOB COMMUNICATOR ………………………………………………………11

PREPARING THE KEY FOB FOR OPERATION…………………………………………………….11

Symbols on the display of the key fob communicator…………………………………..11

PURPOSE OF KEY FOB COMMUNICATOR BUTTONS………………………13

CORRESPONDENCE OF PRIMARY AND AUXILIARY BUTTONS

KEY RINGS …………………………………………………………………………………………14

SETTING THE TIME ON THE DISPLAY OF THE KEY FOB COMMUNICATOR ....14

SETTING OPERATING MODES OF THE KEY FOB COMMUNICATOR ………..15 OPERATION …………………………………………..16

ARMING …………………………………………………………………………………16

ARMING WITH THE ENGINE RUNNING……………18

TURBO MODE…………………………………………………………………………………..18

DISARMING ………………………………………………………………………………19

OPENING THE TRUNK ……………………………………………………………………………….20

CHECKING CONDITION ………………………………………………………………………………..21

JACKSTOP™ ANTI-JACK MODE ……………………………………………………….22

TURNING OFF SIREN SIGNALS……………………………………………………23

“Sherkhan Magikar”: why you should choose alarms from this series

This series has become quite popular in the modern market. Each of the models has its fans and admirers. The list of additional functions and features will surprise even the most biased buyers.

Alarm.
Ability to lock buttons.
Timer for parking.
Energy saving with improved performance.
Possibility to connect additional sensors.
Tachometer.
It is permissible to use one key fob to control two cars at once.
Slave – the alarm provides access to remote control.

Low cost is one of the main advantages of an alarm system. The connection to the CAN bus also cannot be ignored, as well as autostart.

A special adapter is built inside the processor unit. Thanks to this, alarm installation becomes even simpler and more affordable.

Technical solutions using the latest technologies are indispensable assistants for car owners.

You still have to spend at least a day on installation, but the result is worth it. The keychain will become an indispensable assistant.

The alarm can be installed without problems, even if it is necessary to reach the most difficult places. That’s why scammers spend too much time searching and hacking; no one likes to take that kind of risk. A mandatory attachment to the kit will be a user manual.

OPERATING MANUAL VALET MODE ………………….

Page 4

Image
Text

MANUAL

VALET MODE…………………………………………………………………………………..25

DISCONNECTING THE SHOCK SENSOR AND AUXILIARY

SENSOR …………………………………………………………………………………………..26

CENTRAL LOCKING CONTROL BY SWITCH ON

AND TURNING OFF THE IGNITION. ………………………………………………………….28

PASSIVE ARMING …………………………………………….28

SETTING A TIMER TO ACTIVATE AUX. CHANNEL 1………………..30

CONTROL OF “ADDITIONAL CHANNEL 1” ……………………………..32

CONTROL OF “ADDITIONAL CHANNEL 2” ……………………………..33

ALARM MODE………………………………………………………………………………..34

REMINDER MODE………………………………………………………………………………..35

CALLING THE CAR OWNER ………………………………………………………36 PROGRAMMING PERSONAL CODES …..37

PROGRAMMING PERSONAL CODE PIN 1………………………37

EMERGENCY SHUTDOWN MODE WITH APPLICATION

PERSONAL CODE PIN 1 ……………………………………………………….38

PROGRAMMING PERSONAL CODE PIN 2………………………40 ADDITIONAL FEATURES……………………….42

WARNING ABOUT PARKING LIGHTS ON……………..42

STARTER AND IGNITION INLOCKING………………………………………………………42

DOOR OPEN WARNING ……………………………………………………42

PROTECTION OF RADIO CHANNEL FROM CODE INTERCEPTION…………………………………43

ADJUSTING THE SENSITIVITY OF THE SHOCK SENSOR …………………….43

ADJUSTING THE CALL SENSOR SENSITIVITY ………………….43

PROTECTION AGAINST UNAUTHORIZED ENTRY OF KEY FOBS ………….44 PROGRAMMING NEW KEY FOBS …………….44

PROGRAMMING METHOD FOR NEW KEY FOBS …………………….44 FUNCTION PROGRAMMING ………………………….45

PROGRAMMABLE FUNCTIONS MENU No. 1………………………………………47

DETAILED DESCRIPTION OF PROGRAMMABLE

MENU FUNCTIONS No. 1 …………………………………………………………………………………..48

INSTALLING PROGRAMMABLE FUNCTIONS OF MENU No. 1

TO FACTORY VALUES…………………………………………………………………………………54

PROGRAMMABLE FUNCTIONS MENU No. 2 ………………………………………54

SCHER-KHAN MAGICAR B

ATTENTION!

The values of this function depend on the vehicle design.

Incorrect selection of this function may result in

failure of the electric trunk lock, reduction of its service life, or

damage to standard vehicle equipment. If you are not sure about your choice

value of this function, before changing the factory setting

Consult with the technical specialists of the dealer of this brand

cars in your region.

Programmable function 2-4: “Events for enabling “additional channel 1”

This function allows you to control an additional channel of the key fob without

only from the key fob, but also from system events: arming,

disarming, by timer.

This programmable function has four meanings:

Only pressing buttons (I+IV) (factory setting)
2)
Arming or pressing buttons (I+IV)
3)
Disarming or pressing buttons (I+IV)
4)
By timer at a specified time or pressing buttons ( I+IV). The user can set the required time on the key fob with an accuracy of 1 minute for

activating an additional channel and turning on the timer function (see.

item “Setting the timer mode”, page 30)

Programmable function 2-5: “Events for enabling “additional channel 2”

This function allows you to control an additional channel of the key fob without

only from the key fob, but also from system events, but the events are different than for

"additional channel 1".

This programmable function has four meanings:

Only pressing buttons (III+IV) (factory setting)
2)
Alarm in security mode from trunk/hood, door, ignition sensors or pressing buttons (III+IV)
3)
Pressing buttons (III+IV) or turning on the ignition
4)
Turbo timer . When this programmable feature is selected, the signal on Auxiliary Channel 2 will appear immediately when

turn off the ignition and last 120 seconds. regardless of value

Specifications

Installation of Sherkhan car alarms is only possible on vehicles with a 12-volt on-board network. The use of complexes on “heavy duty” vehicles and motorcycles is impossible due to the fact that their voltage is 24 and 9 V, respectively.

Description of the main properties and parameters of the alarm for the Scher-Khan car:

the operating temperature range recommended for the use of anti-theft systems is from -40 to +85 degrees;
weight of the microprocessor device - 105-210 grams, depending on the model;
in security control mode, the main unit should consume no more than 15 mA;
the total load of low-current outputs is 250 mA;
microprocessor alarm modules Sherkhan with auto start are supplied in IP-40 housings;
the range of the communicator and transceiver is 1.2 and 2 km, respectively;
Signals are transmitted via a radio channel with a frequency of 433-868 MHz, depending on the model;
pulse modulation type - FM;
The main remote control uses AAA batteries, the additional remote control uses CR2016 batteries;
communicators are powered by 1.5 or 6 volt batteries, depending on the device.

The Ben & Ice Video Master channel spoke in detail about the characteristics and functions of the alarm using the example of the Sherkhan Mobicar 1 model.

MANUAL …

Page 5

Image
Text

MANUAL

The combination of buttons (I+II) turns on or off all signals (siren in alarm mode, short signals - when arming and disarming

security mode, alarm signals - in alarm mode).

In this case, all information will be transferred to the key fob as usual.

Hidden security mode

Programmable function 2-2: “Trunk lock control in security mode”

This function allows the user to select whether to remove the system when

unlocking the trunk from security and unlocking the electric door locks

or not.

This programmable function has two meanings:

When the trunk lock is unlocked remotely, the system does not disarm; after activating the trunk lock, the system

disables shock sensor, additional sensor, hood sensor/

trunk for 15 seconds. If the trunk has not been opened during this time, then

after 15 seconds, the system will again start tracking disabled

sensors If the trunk was open, the system will start tracking

disabled sensors 15 seconds after the trunk is

closed (factory setting) 2)

When the trunk is unlocked remotely, the system is disarmed and the central locking is unlocked.

Programmable function 2-3: “Trunk lock control pulse duration”

This function allows you to change the duration of the lock control pulses

trunk (signals on connector CN1). The choice of value for this function depends

on the design of the vehicle on which the system is installed. For example,

if the connection occurs to a button in the cabin, which to eliminate

false alarm requires some holding time, then it is required

select the second or third value of this function.

This programmable function has three meanings:

0.5 sec.
(factory setting) 2)
2 sec.
3)
4 sec.

SCHER-KHAN MAGICAR B

DETAILED DESCRIPTION OF PROGRAMMABLE

MENU FUNCTIONS No. 2 …………………………………………………………………………………..55

INSTALLING PROGRAMMABLE FUNCTIONS OF MENU No. 2

TO FACTORY VALUES …………………………………………………………………………………59

PURPOSE OF SCHER-KHAN MAGICAR B

SCHER-KHAN MAGICAR B is a car alarm

with the ability to control via radio channel via key fob -

communicator with liquid crystal display. The system implements

exchange of information between the key fob communicator and the processor

block at a distance of up to 800 m. The car alarm is designed for

work on vehicles with 12V on-board voltage and grounded

negative terminal of the battery. Protection of the processor unit, sensor

shock, call sensor, antenna unit is made according to the IP-40 standard and

Provides for installation inside the car. Siren made according to

IP-65 standard and can be installed in the engine compartment, away from

exhaust manifold and high-voltage systems.

CONTENTS OF DELIVERY

When purchasing a system, make sure that it is included. Specified

The delivery set is basic and can be supplemented

according to the buyer's wishes.

Name Quantity

Operating manual………………………………………………………..1

Installation Guide………………………………………………………………………………..1

Processing unit SCHER-KHAN MAGICAR B……………………………………….1

Keychain communicator……………………………………………………………………1

Key fob without display…………………………………………………………………………………1

Shock sensor with cable CN5…………………………………………………………………………………..1

Car call sensor and LED

indicator (LED) with cable CN6………………………………………………………..1

Antenna unit with cable CN7…………………………………………………………..1

Temperature sensor………………………………………………………………………………………..1

Locking relay…………………………………………………………………………………1

Siren……………………………………………………………………………………………………………..1

How to turn on the key fob

The power supply for the additional alarm remote control Magicar A, C, 5, 6 Mini lasts for 6-8 months. The switch simply stops working after this time. How to properly replace the battery without damaging the key fob:

Use a small Phillips screwdriver to unscrew the screw.
Very carefully open the internal latches around the perimeter of the case.
Replace old batteries, observing correct polarity.
Reassemble the keychain in reverse order. If necessary, write it down, adhering to the points from the previously given instructions.

We also have instructions for setting up your Jaguar key fob.

Advantages and disadvantages of autostart systems

Advantages of Sherkhan alarms with the option of automatic engine start:

Great functionality to simplify the management of standard vehicle systems. To do this, the alarm must be correctly connected to the additional equipment. We are talking about electric windows, sunroof, side mirrors, air conditioning, heating, etc.
Easy to install. The service manual includes a detailed wiring diagram for connecting the alarm. Therefore, the user should not have problems connecting contacts.
Effective vehicle protection. Thanks to the use of special encodings, the likelihood of intercepting signals transmitted between the antenna and the key fob is minimized.
Affordable price.

Flaws:

The need to reprogram the remote control. Some models of anti-theft systems are equipped with communicators with an English-language interface. This may not cause problems for some users when setting up basic security functions. However, if the parameters of additional options are changed, this will cause inconvenience.
Fragile body of the communicator. Minor falls may cause the device to malfunction. If the key fob cracks and its internal circuit board is damaged, you will have to use the services of specialists to restore it.

Equipment

Overview of items supplied with automatic start systems:

Operating instructions allowing you to correctly install and connect the alarm. The service manual describes in detail all the nuances regarding setup and programming.
Electrical circuits for alarm installation.
Microprocessor device.
The main key fob equipped with a screen.
A set of connectors and wires for connection.
Transceiver module. In many models, this device is combined with an LED alarm status indicator. Depending on the system, the diode may be supplied separately.
Siren.
Engine blocking relay with connector.
Limit switch for installation on the trunk or hood.
Shock sensor with connected wire.
Spare remote control.
Stickers for fixing the transceiver module, as well as for the windshield.

Since the Sherkhan Magikar alarm package includes one limit switch for the hood, devices for the doors must be purchased separately.

Photo gallery

Photos of elements of Sherkhan anti-theft systems:

Antenna alarm module

Box and remote control from Mobicar B

Signal control unit