Kamaz gearbox: device, divider, switching diagram

Box modifications

The type of box installed depends on the loads the vehicle experiences and the conditions in which it is operated:

• KPP-14;
• KPP-15;
• KPP-16;
• KamAZ ZF gearbox.

The fourteenth transmission is a five-speed device, which includes a gearbox. The fifteenth modification of the product with ten stages, unlike KamAZ-14, is equipped with a divider with two stages, the device is located in the front part of the box.

Gearbox KamAZ-14:

Transmissions are controlled mechanically, remotely, using a swing lever located on the power plant. The mechanical gearbox is controlled by pneumatics and mechanics, through a selector. The driver directly acts on the rocker.

The sixteenth gearbox, with eight shift stages, is of mechanical type. The design includes a four-stage gearbox and a reduction box mounted behind the structure.

The base of the rod that switches the stages is installed on the gearbox plug; the lever itself is made in an original design solution. The product contains a rod that controls the gearbox, a lever, a safety net that prevents erroneous start of reverse, and valves controlled by pneumatics and switching a mechanism that increases torque.

Gearbox KamAZ - 15:

The ZF gearbox on KamAZ with nine stages is equipped with an auxiliary reduction gear, unlike the 16 model.

The KamAZ 5320 gearbox is equipped with five stages. Since the equipment is operated in harsh conditions, it is equipped with large gear ratios for operation at low speeds. Switching occurs in stages, the transmission easily adapts to road conditions.

KamAZ ZF gearbox:

Gear controls on modern cars are different. A mechanism with fewer gears is used on vehicles with a smaller load capacity and dimensions. Modifications of 10 stages are installed on road trains. KamAZ is in demand in 40 countries because the control mechanisms are reliable and durable.

Malfunctions and repairs

Transmission repair consists of disassembling the unit, diagnosing, repairing or replacing worn elements. After the mechanism is restored, the unit is reassembled and the system is tested in operation. You can contact a service center, but it is better to repair the transfer case yourself.

How to check the oil level

The oil level in the box is checked as follows. Unscrew the crankcase plug. When checking, you must install the crankcase indicator into the hole until it stops. The oil from the crankcase of a ten-speed manual transmission is drained through 3 holes. Of these, 2 holes are located in the lower part of the gearbox housing, and the third is located in the divider. The five-speed gearbox housing is drained through 2 holes.

Description of gearboxes

Structurally, the ten-speed transmission is a box with five steps and a gearbox. This design uses 10 forward gears and 2 reverse gears. The transmission is popular and is used for installation on vehicles carrying heavy loads. The mechanism received index 15.

Distinctive features of the KamAZ-15 box:

• Used in conjunction with a reinforced divider synchronizer;
• The splines have been modernized and strengthened, the fastening parts have been removed from the box;
• The fixation of transmission gears has been modernized;
• The height of the teeth has been increased.

Downshift (divider) valve for KamAZ-15:

The pneumatic system activates and controls the KamAZ transmission dividing device. The performance and durability of the unit directly depends on the correct use of this unit. For the same reason, inspection of the KamAZ transmission is carried out at specialized stations.

KamAZ transmission elements:

1. Box body with built-in shafts: driving, driven, intermediate;
2. Gear mechanism for activating reverse;
3. Upper casing;
4. Collapsible mechanism that switches stages;
5. The power unit is located in the front of the body.

Switching rules under different conditions

The driver must know how to change gears to control the vehicle:

• on the rise;
• moving on a descent;
• moving on ice and icy areas of the road surface;
• when skidding.

On the rise

Features of KamAZ gearbox control on a hill:

• Driving uphill should be done in high gear;
• To switch from first speed to second, you need to press the clutch pedal twice;
• when performing a maneuver, you must simultaneously depress the gas pedal and the fuel pedal;
• when driving on a hill, you cannot reduce the engine speed to less than 2 thousand per minute (otherwise the engine will stall).

On the descent

Rules for controlling the KamAZ transmission when driving on a descent:

1. When driving downhill, do not turn off the engine, since stopping the power unit will cause the power steering to lock.
2. When driving downhill, the additional braking system must not be turned off. Also, do not press the clutch pedal all the way.

Modern KamAZ vehicles are equipped with a double-force braking system; accordingly, in addition to engine braking, an additional power unit stopping unit is used. If driving downhill is carried out with the auxiliary braking engaged, then disengaging the clutch and changing gears is not allowed.

Icy areas

Features of driving a KamAZ vehicle on ice and icy road surfaces:

1. Driving on ice in a vehicle must be carried out with the maximum allowable speed and travel. Compliance with this nuance will allow you to avoid a traffic accident in an emergency.
2. When braking, it is necessary to use the active additional stopping system of the power unit.
3. If an emergency occurs while driving, you need to stop the trailer wheels. Otherwise, the car may skid.
4. Engine braking is allowed in exceptional cases, as this causes rapid wear of the motor elements. But in emergency situations, such a maneuver will reduce the length of the braking distance.
5. When braking, do not allow the wheel to slip. To do this, it is recommended to activate a lower gear in time, since it will reduce the engine crankshaft speed.

During a skid

Rules for using the gearbox during a skid:

1. In such a situation, it is not allowed to depress the clutch pedal, as this will lead to a stronger spin.
2. During a skid, you need to turn the steering wheel in his direction. In particular, if the body of the car moves to the right, then the steering wheel, accordingly, also scrolls to the right.
3. If the car slips during a skid, you must stop moving and turn off the differential axle. The regulator itself for performing this task is located on the instrument cluster. After the device is turned off, the corresponding icon will appear on the dashboard. Then you need to start moving in high gear from second speed.
4. After the driver copes with the skid, it is necessary to engage the differential.

Box divider

High and low operating modes, a feature of KamAZ gearboxes. This specificity is caused by the desire to reduce the load on the power plant. It is typical that it does not matter whether the machine is loaded or not. A divider is a gearbox based on the principle of mechanics and increases gear ratios. The mechanism is started using a switch on the rocker.

The design includes:

KamAZ-15 box divider input shaft:

1. The valve that controls the device. The part is attached to the base of the switch, uses direct and reduced speed modes.
2. A valve that maintains a constant outlet pressure. It takes compressed air and resets the pressure in the system when the established values ​​are exceeded. Transfers air to the control valve and to the valve of the dividing device from the air unit. Thanks to manipulations, there are simultaneously two circuits in the engine control system.
3. Divider activation valve. Supplies air pressure to the device when the clutch is disconnected. This engages and disengages low gear, paralleling the transmission's gear changes.
4. Dividing mechanism. The composition includes a piston placed inside a cylinder. The piston lever is connected to a rod fixed to the fork shaft of the assembly. When air pressure hits, the piston moves, this changes the operating mode of the box.
5. The air distribution pipe supplies air pressure to the cylinder of the unit.

How to use a divider on a Kamaz

It is necessary to skillfully combine the divider gears with the gearbox gears.
Acquiring the skills to correctly select gearboxes and dividers can significantly reduce fuel consumption, increase the average speed, create a more economical mode for engine operation, and increase the service life of the clutch, brakes, cardan transmission and drive axles. Gear shifting in the divider is carried out by moving the control valve switch installed in the head of the gear shift lever.

To change gears in the divider, the control valve switch should be moved to the upper or lower position, which corresponds to the highest or lowest gear. Press the clutch pedal all the way and hold it until the gear is fully engaged in the divider (approximately 0.6...0.8 s). When the clutch pedal is pressed all the way, the divider activation valve opens and the divider automatically switches to the selected gear. After this, smoothly release the clutch pedal.

Promotional offers based on your interests:

The control valve switch can be moved to the selected gear position in advance. After this, at the right moment, it is enough to depress the clutch pedal all the way.

When starting the car from a place, the gears in the divider are selected depending on the road conditions and vehicle load.

To accelerate the car to a speed of 10...11 m/s (30...40 km/h) (i.e. to third or fourth gear), it is enough to change the gear in the main box without changing the gear in the divider. To accelerate from third or fourth gear, it is advisable to use both gears of the divider. To do this, when accelerating in difficult road conditions, the following switching sequence is recommended: 1Н—2Н—ЗН—4Н—4В—5Н—5В, when accelerating a car on a paved road—IB—2В—ЗВ—4Н— -5Н-5В.

If during acceleration it is necessary to simultaneously change gears in the main box and the divider, then you should move the switch of the divider control valve to position H, depress the clutch pedal all the way and engage the next higher gear in the gearbox, then smoothly release the clutch pedal.

If the car is moving with the low gear of the divider engaged, and the road resistance has increased and it is necessary to simultaneously change gears in the gearbox and the divider, you should move the divider control valve switch to position B, depress the clutch pedal all the way and engage the next lower gear in the gearbox, then smoothly release the clutch pedal.

Technical parameters of KamAZ gearboxes

The transmission of KamAZ vehicles is equipped with gearboxes that differ in gear ratios. For this reason, cars are used in many areas. The gear ratios are shown in the table below.

In addition to gear ratios, the characteristics of the box modifications differ structurally. Thus, some models are equipped with parts and components that are not available in other modifications. ZF transmissions are assembled at the Russian plant, together with German partners, at the ZF-KAMA plant in Naberezhnye Chelny.

Start

The movement starts from the lowest level. The speed change is performed only with the clutch depressed, in several stages. The pattern is associated with upshifts and downshifts, which makes it possible to use the car on different surfaces and terrain.

A successful scheme is considered to be switching 1B-2B-3B when picking up speed, 4H-4B-5H when driving further. When starting, the shaft speed is increased to 7000 min-1, second gear is used after 3000 min-1. The correct operation of the gearbox and its durability depend on strict adherence to the regime on KamAZ 65115 and others. The correct modes reduce fuel consumption, make driving more economical, and extend the life of the power plant.

Gearbox KamAZ 4310 shift diagram:

Reverse

On the Russian KamAZ, not only the front, but also the rear gears are switched on, and there can be two of the latter (if we are talking about a ten-speed gearbox, for example, on a model 55102 truck). The switching diagram clearly shows that to activate reverse gear, you must move the gearshift lever to the lower left position.

Important - it is strictly forbidden to engage reverse while driving. You must first stop the car and only then switch the lever to the appropriate position.

Switching Features

If a KamAZ vehicle is driving down a mountain, use high gear. The transition from 1st to 2nd speed occurs by pressing the clutch foot lever twice. The maneuver is accompanied by the addition of gas in order to smooth out the crankshaft speed. If the car goes up, the shaft speed should be 2000 min-1 or higher. Failure to follow this advice will lead to overheating, as well as to stopping and failure of the motor.

The KamAZ transmission is distinguished by its quality, reliability and directional stability during operation. Dividing the box into two modes is used to make the engine easier to move under different vehicle loads. When starting on a loaded vehicle, an increased speed is used, bringing the shaft rotation to 2600 min-1.

Shifting gears on KamAZ (ZF):

Instructions for shifting gearbox

Operation of the transmission includes three main nuances:

• correct start of movement;
• features of selecting and switching speeds;
• using reverse gear.

Getting started: at what speed should you start?

After the engine has been started and the motor has begun to operate, driving should begin in a low gear. When moving away, you only need to engage the speed with the clutch disengaged.

On transmissions of KamAZ vehicles, the gear shift diagram is carried out in a certain sequence:

1. At the first stage after starting to move, you need to engage gear 1B (increased first speed mode).
2. As the speed increases, the lever switches to 2B mode.
3. At the last stage of starting, the 3B gear is activated.

Accordingly, on the main box there is no need to touch the lever up to the fourth speed. To start driving, you need to increase the crankshaft speed to 7 thousand revolutions per minute.

It is important to know

Switching to second gear while driving is possible only after the number of revolutions on the tachometer reaches 3 thousand/min.

How to change speeds correctly?

After acceleration, the order in which the speeds are turned on will be as follows:

1. There is a transition to the second lower stage and activation of the fourth speed (4H).
2. Then the primary stage is activated, while the movement speed must remain fourth (4B).
3. At the next stage, you need to go to a lower gear and activate the fifth speed (5H).
4. The driver then returns to the higher gear, but the vehicle continues to move at fifth speed (5B).

How to turn on reverse?

Reverse must be engaged by moving the gearbox lever to the lower left position. Activation of reverse gear is not permitted while driving or if the vehicle is rolling. To engage reverse gear, you need to completely stop the vehicle and then perform the maneuver.

Video: rules for shifting gears on KamAZ

Nikita Vagin in his video spoke in detail about how many speeds there are in KamAZ, as well as about the scheme and nuances of switching them

Caring for the KamAZ gearbox

The device needs to be adjusted and configured, otherwise failures such as difficult shifting and knocking out gears cannot be avoided. Important manipulations include: adjusting the switching mechanism, adjusting the backlash of the rod, adjusting the gap in the divider activation valve, etc.

Checking the oil level in the KamAZ gearbox crankcase:

Changing the lubricant is considered part of the maintenance. The procedure is carried out once a year, mileage does not exceed 90,000 km. When operating the machine in difficult conditions, the lubricant is drained every 45,000 km. or 1000 hours of operation (depending on the established regulations and modification of the box).

Checking the fluid in the 14th and 15th series transmissions is carried out using marks on the neck cover. In the 16th series and ZF, a test hole is used for checking.

Frequent breakdowns include: difficult activation, wear of parts, malfunction of the reverse gear, spontaneous shutdown, etc. Problems are solved by adjusting the mechanism; in case of serious issues, contact a specialist.

Specifications

The KamAZ gearbox with a divider includes the following elements:

• a crankcase in which the drive, driven and intermediate shafts assembled with gears are mounted;
• bearings;
• synchronizers,
• reverse gear block,
• top cover of the box,
• gear shift mechanism.

The gearbox of KamAZ vehicles can be five- or ten-speed. The gearbox divider has high and low gears and, in combination with the main gearbox, allows for 10 forward gears and 2 reverse gears. The divider system improves the traction qualities of the machine, makes it easier to control, and reduces the frequency of shifting gears with a lever. Transmission ratios are available in the operating instructions for the device.

The 141 KamAZ gearbox has a reversing light switch. To prevent the simultaneous activation of 2 gears, there is a ball-type lock in the cover, and a spring-finger fuse is used to prevent accidental engagement of reverse gear. The gearbox with divider weighs 320 kg. The cuffs are located in the shaft covers. They protect the gearbox from clogging and prevent oil leakage. Insufficient oil volume in the gearbox leads to its damage. When you first fill the gearbox there should be 9 liters of oil, when changing the fluid - 8 liters.