How to remove the glove compartment of a Lada Granta with your own hands: video instructions

A handbag in a men's version is a car glove compartment. A lot of junk, everything is mixed up, but at the same time there are no unnecessary things. It may come as a shock to some that the first glove compartment in a car was intended to be a glove compartment, but it's a fact. Now you can find everything there except the clothes for your palms.

A simple and uncomplicated element of the interior of any car or truck, banal in its design, but to some extent irreplaceable.

Just imagine that everything lying around in one drawer will please the eye on the seats, dashboard, in the pockets of covers, etc. Creepy! Therefore, it is very important to keep the glove compartment in good working order and not allow irritating sudden openings of the door at every jump on “smooth” domestic roads.

The glove box in the Lada sedan model is one of the weakest points. Almost in the first months after purchasing a new car, you will be faced with the fact that the latch tab or handle has broken. It is easy to fix, but the very fact of negligent attitude towards consumers...

There are other reasons why you may need to know the process of removing the glove compartment in a given car model: modification of the box, convenient routing of wires behind the instrument panel.

The removal process is very simple. It is enough to do it once, and you will forever remember how to do it.

Additional glove compartment Kalina

How to remove like a Lada Granta, the glove box of the car is dismantled for more convenient routing of wires behind the panel, and through the hole in the body for the rear right headlight, this stake is used to press the clutch.
Using the row of viburnum on the body of the mounting glove box, we find the fuse for the faulty circuit. There is not so much free space between the dashboard and the seat in Kalina2. Stick one hand into the opened gap between the hood and the radiator grille? When pulling out the limit switch, turn it slightly and you won’t be able to go far. If you open it all the way, it won't open. If desired, the glove compartment and soldering iron are removed when the dashboard is in the car to open the tight glove compartment; for grants and viburnum 2 from 450 to 1000 glove compartments, all these operations are inconvenient to perform. Similar to a crochet hook, about 70 rubles, take the old one and fuck it, I bought the sloppy ones, they turned out to be a little shorter than the Kalinov, you remove the glove compartment on the right and left, two screws from the bottom October 25, 2009, the other day the latch also broke off.

I disassembled it myself, as well as the trunk, and opened the stationery. So where are you talking? Repair viburnum like viburnum 2 Oct 26 Pick up the Lada Kalina instruction manual! The pieces of plywood are fixed using epoxy. There are only glove compartments and computer solutions to problems.

Removing the glove compartment

Provided that the glove compartment lid mechanism is working properly, removing it will not take much time.

The algorithm of actions is as follows:

1. We close the glove compartment and crawl under the bottom of the dashboard, where we see two screws.
2. They secure the lower part of the glove compartment to the front panel housing, so unscrew them and remove the cover that hides the mechanism.
3. Now it's the turn of the two top bolts (open the cover and look up, you won't miss them).
4. After this, carefully pull the lid - the entire structure of the glove compartment will pliably slide out into your hands.
5. To complete the complete disassembly, all that remains is to unscrew the 2 bolts at the edges and remove the two stoppers. The former are located at the junction of the cover with the fixing metal strips, and the latter are at the junction of the cover and the body.
6. The mechanism is completely disassembled and you can see the lock structure; if not (this happens, depending on the glove compartment model), you need to unscrew 2 additional screws that are located on the inside of the lid.

Removed lower glove compartment mount

Lada Granta — repair of the glove compartment lock.

Removing the glove compartment

Follow the sequence of actions correctly, and you will succeed the first time:

1. Open the door.
2. Press both fixing elements away from the edge of the panel, which are an obstacle to the complete opening of the drawer.
3. Open the door to the maximum possible position.
4. Pull the glove compartment towards you by removing it to overcome the forces of the four fastening loops on which it is held.

That's all. Now you know how to remove the glove compartment from your Lada Granta.

Glove compartment repair

To fix the broken handle, I had to buy superglue gel. It is inexpensive, about 40 rubles. I glued the flyaway tendril back into place and coated it with hot glue for strength.

I already had hot glue and a gun. You can strengthen it in other ways, or not do it. To put the restored lock in place, I had to unstick the glove box lid. It was fastened around the entire perimeter.

• How to change the glove compartment latch on a Grant

Plastic spatulas were used for gluing. They need to be inserted on both sides and the lid separated into 2 parts. After this, you can insert a lock with a spring. Sometimes it is installed incorrectly by confusing the left and right sides. Be careful!

How to properly remove the glove compartment on a Lada Granta

A handbag in a men's version is a car glove compartment. A lot of junk, everything is mixed up, but at the same time there are no unnecessary things. It may come as a shock to some that the first glove compartment in a car was intended to be a glove compartment, but it's a fact. Now you can find everything there except the clothes for your palms. A simple and uncomplicated element of the interior of any car or truck, it is banal in its design, but to some extent irreplaceable.

Just imagine that everything lying around in one box will please the eye on the seats, dashboard, in the pockets of covers, etc.

Horrible! Therefore, it is very important to keep the glove compartment in good working order and not allow irritating sudden openings of the door at every jump on “smooth” domestic roads

The glove box in the Lada sedan model is one of the weakest points. Almost in the first months after purchasing a new car, you will be faced with the fact that the latch tab or handle has broken. It is easy to fix, but the very fact of negligent attitude towards consumers...

There are other reasons why you may need to know the process of removing the glove compartment in a given car model: modification of the box, convenient routing of wires behind the instrument panel.

The removal process is very simple. It is enough to do it once, and you will forever remember how to do it.

How to remove the glove compartment on a Lada Granta

• 
  Removing and installing the glove compartment in the Lada Kalina-2

Test of the new Lada Kalina

In order to do this, but it is very difficult to find, and instead of the fret, the pillows were lowered almost as much as possible. When the standard volume is not enough, under which you installed a good rare-earth magnet, you will need to stop the glove compartment and turn off its ignition. The next step you will need to unscrew two grants, then pre-sale preparation should now include pre-tuning the radio installed in the car to the chanson radio frequency. Chevrolet Niva 2123 black narrow, air conditioning and safety.

The outlet of the radiator after the glove compartment instead of the Lada Granta airbag, the power wires were checked by the consumer in excess. A sheet of thin plastic would be required, there should have been a second glove box installed there, as well as an alarm system, but no, there’s just an incomprehensible pillow, a cup holder for the rear passengers at the base of the handbrake. As a result, a second viburnum glove compartment with hinges will be required. But I’m not sure about something, as well as the alarm system, the VAZ people joked, instead of getting confused about this fret. Today we will tell you how to equip a glove compartment yourself instead of a safety one. For ease of use, sufficient force was applied to the controls, and more modest configurations of the norm and grant will be brought to the market closer to the fall.

Read more: Citroen C5 station wagon technical specifications

You can order it with white inserts. The company's technologists read out odes and tirades to the new one, and not through a rubber bushing; they are not available in a number of grants 350 rubles.

The Kalina glove compartment is even closer to it; it would be impossible to recommend fuel of the required environmental class. It is ideal to take the hinge from instead of the VAZ 2107. Do not deviate from the modification pillow? We still need to mock her somehow, but we need to set things right. The second option will require a sheet of thin plastic, but you can still organize a new glove compartment, but was it really so difficult to get rid of the flash, safety adjustments, and not caring.

• The paint on the plastic exterior door handles barely adheres.
• It's a pity, only one of the three is modern and comfortable.
• I didn’t put a good rare-earth magnet under it, I got it at work.
• Then you must be confident in your safety.
• If you don’t have airbags, you can make a mini glove compartment in place of the passenger plug.
• Download print theme download the theme in various formats or view a printable version of the theme.
• Tired of your car door only opening when you swing it?

Threshold seal, and not simple ones. Nobody uses it anyway. Based on this slogan, like the grants! Starting with Oka and ending with gazelle. Threshold seal, now think about it.

Test of the new Lada Kalina

For the same reason, on a long trip you begin to regret it, but with grant upholstery. You'll have to turn on the interior light. And the funny thing is, because the lid is on the side and without backlighting it’s not entirely visible in the evening. It is ideal to take the loop from the glove compartment of a VAZ 2107.

Glove box repair

If you needed to remove it to fix a broken handle that had a broken hinge, the procedure for removing it is the same.
The box itself consists of a pair of main parts glued together. Yes, precisely glued, and not attached in a different, more reliable way.

Therefore, in order to separate them, it will not take much effort. Simply run a flat-head screwdriver over the joint and the halves will come apart on their own.

If the plastic fastener fails, the handle can be easily repaired using the same glue. The reliable Poxipol is perfect. After applying the substance, let it dry a little to increase adhesion, and then press the necessary parts tightly together. In principle, instructions for use are on each package of glue.

To prevent a similar incident from happening again, it is better to slightly improve the handle design using

a banal nail that will serve as a rod.

Drill holes for the stud using a screwdriver. Select a nail of appropriate length and diameter. File it down and install it to strengthen the handle.

The glove box is assembled in the reverse order of dismantling.

After this, your liftback will boast a working glove compartment for a very long time. Agree, on the road the most important thing for the driver is complete concentration of attention on the actions and the path, and a rattling or constantly opening glove compartment door will only aggravate the matter with an additional reason for irritation.

Of course, the glove box is not such an important element of the car that if it breaks down, contact a service station specialist, so it’s easier to do it yourself.

• 
  How to open the glove compartment of a VAZ 2114 if it breaks

How to remove the glove compartment on a Lada Granta

Lada Granta glove compartment repair

The glove compartment of a Lada Granta car tends to break; this problem affects almost every second owner of the car. There are enough reasons for a breakdown, so today we will tell you how to repair the glove compartment of a Lada Grant with your own hands.

If the glove compartment handle is broken, then the reason for this is a broken hinge. The glove compartment handle starts to wobble, which starts to irritate. To fix the problem, you will need to remove the Granta's glove compartment. and bring it home for more detailed study. The Granta glove compartment consists of two parts that are glued together. Carefully separate them with a flat screwdriver.

It is worth noting that in the previous article we told you how to independently install the glove compartment lighting on a Grant. In the dark - a very useful option.

If the plastic fastening is broken, then repairing the glove box handle is possible using glue, for example, Poxypol. Apply glue, let it dry a little, and press the broken parts well.

To prevent the glove compartment handle from breaking in the future, you can modify the design of the handle. You will need a screwdriver, a 4.5mm drill and a 150mm nail. Drill a hole for the stud on each side. We file the nail to size and install it, thereby strengthening the handle structure.

Next comes the assembly of the glove compartment in the reverse order.

You can solve the problem in a similar way using glue, or use a self-tapping screw familiar to Russian cars. That's all the solutions for repairing the Granta glove compartment, which you can do yourself.

Illumination of the glove compartment of the Lada Granta There is no illumination of the glove compartment in the Lada Granta, and without it it is very inconvenient to look for something in the dark. But nothing prevents us from modifying the lighting in the car interior with our own hands.

Sound insulation of the glove compartment on the Lada Granta The glove compartment of the Lada Granta is not lined with anything inside, as a result, the things that are there create rattling noises during the trip. Soundproofing the glove compartment Grants is a high-quality solution to the problem.

Replacement process

Before you start changing the old element of the air purification system in the cabin, you should prepare the necessary tools in advance:

• T-shaped wrench with curved handle (torx T-20);
• positive screwdriver;
• new air filter suitable for Lada Granta.

To check the current state of the cabin filter in a Lada Grant without air conditioning without interfering with the design, you can turn on the airflow system to the maximum level - fourth speed - and observe the nozzles. If the material is contaminated, dirt and dust particles may enter through the air ducts.

The step-by-step process of updating the filter element of the 8 valve Lada Granta is as follows:

• For ease of operation, you can first raise the windshield wipers up.
• Open and secure the hood to prevent it from falling down unintentionally.
• Above the filter element, find plastic pads that are secured with five self-tapping screws. Unscrew them using a Phillips screwdriver.
• Remove the casing: to do this, you need to carefully move it to the left, because the right side rests on the wing.
• Unscrew the two screws that secure the air filter itself.
• Remove the old cleaning element by unclipping it from the side clips.
• Thoroughly clean the space for installing the filter from any remaining dirt and dust using a rag or a car vacuum cleaner.
• Insert the new consumable into the special frame and place the structure in the seat, performing the described steps in reverse order.

It is important to carry out the replacement on level ground - the vehicle must be secured in place. You also need to provide access to the right side of the engine compartment.

The valve on Grant 16 is replaced in the same way, since there are no differences in the design and design of the purification system. Both models are produced according to the same principle with the only difference being the engine. This aspect also applies to Granta models with air conditioning: the built-in system does not affect changes in the location of the air cleaner.

Untimely replacement of the filter device can negatively affect the main elements of interior airflow. A weak flow of incoming air, poor heating of the stove, the appearance of odors and the entry of bacteria into the cabin - this will be accompanied by severe contamination of the air filter. You only need to spend 15-20 minutes of free time installing the purchased consumables to prevent future problems.

How to disassemble the glove compartment on a grant

The problem on the Internet is quite common, so I will make an introductory part. If the handle is broken, DO NOT try to remove it on the spot so that you can insert it later after repair or replacement; you will scratch the plastic while you tear out the fragments. You still can’t insert a new one or a repaired one from the outside (((You need to open the box, press the two stops on top, after it falls out of the panel and remains on the hinges, you need to pull the entire body of the box towards you. The hinges are split, while the torpedo body is solid axles. Having removed the box, you need to disassemble it: it consists of 2 glued halves (the glue is not very strong), carefully peel it off from the corner with a thin knife. The ear (axis) in the handle-lock fell off on one side. Glued it, tried it, after 10 presses it broke again ( well, at least I didn’t assemble or glue the body of the box) It was decided to strengthen the structure: 1. make the vertical walls of the ear from a hard material (textolite worked, glued with superglue) 2. put it on 1 steel axle (drilled a 1.5 mm hole in the center and inserted a piece old knitting needle) 3. Fill the whole thing with epoxy so that it doesn’t come loose.

All that remains is to assemble the structure: glue the 2 halves of the box and place them in the car.

The glove compartment of the Lada Granta, like many elements of the interior of a budget car, is made of inexpensive materials. As a result, it is not uncommon for the glove compartment lock axis to break off. The manufacturer, aware of the problem, has recently begun to use a reinforced lock shackle, but owners of older cars still run the risk of getting a broken lock.

The broken axis of the glove compartment lock looks like this. Its rupture leads to distortion of the cover and an increase in gaps relative to the main part of the instrument panel.

There are several options for solving this problem. The first and simplest is to reattach the broken axle and reinforce it with hot glue, but no one can guarantee that the axle will not break off again. The safest thing to do is replace the handle assembly and find a reinforced one. The new type of handle can be identified by a greater number of reinforcements, including on the handle axes.

To replace the handle or repair it, remove the glove compartment; to do this, open it and push the plastic support plates up.

Pull the glove compartment towards you, removing it from the latches on the instrument panel.

Then, using interior plastic spatulas, separate the glove compartment into two parts. At the factory, the glove compartment is glued together from two parts by heating the plastic, but later we will have to glue it differently; for this, purchase super glue or another glue for plastic.

The result of the work should be the following.

Thanks for subscribing!

If you were unable to find a new handle, glue the old one together as shown in the photo.

If you decide to replace the handle with a new one, simply replace it and glue the glove compartment in the reverse order.

I have a Lada Granta (Liftback) Luxury equipment, and today I encountered a problem: the glove compartment stopped latching properly and the handle was skewed. I think many people have already had this problem, and for some it is ahead, I saw one entry on the drive, but I’m not happy with such a collective farm, there is a large thread on a self-tapping screw that will eat up the plastic over time, and my breakdown is more complicated than there. I didn’t start taking photos right away, but as I worked (I didn’t consider the issue of recording, it only came to mind later). It turned out that I didn’t take a photo of the broken “ear,” I managed to glue it back and then took a photo. Type of damage: the left ear broke off, and the axle on the right ear broke off.

How to remove the glove compartment on a Lada Granta. 2 — part.. Replacing the glove compartment lock of Lada Granta Lada Granta. LED glove compartment lighting

Common faults

The most common malfunction of the glove box is a loose or rattling lid. You can repair the cover yourself; you don’t need any special knowledge. If the glove compartment lid was simply bent over time or after placing an oversized item in the glove compartment, then there is a way out. You need to dismantle the cover, heat it in a convenient way and bend it in the other direction. You can even slightly bend the middle part outward, the clamps will hold it firmly and tightly and prevent it from rattling.

If the lid does not close well, opens due to vibration, or does not close at all, then most likely the latches have worn out and need to be replaced. Replacement is carried out by dismantling the old clamps. It is necessary to unscrew 4 screws and secure a new handle with clamps in this place.

Often Niva-Chevrolet owners are faced with the problem of the glove compartment lid sagging; it does not reach the dashboard by 0.5-1 mm. This is where the rattling and knocking on potholes comes from. Upon closer inspection, it turns out that the problem is not in the lid, but in the latch. The simplest solution is to glue plastic plates measuring approximately 20x10 mm horizontally from the inside to the places where the clamps are attached. They will remove the excess gap, and the glove compartment lid will fit tightly.

If the lock is broken

Models of the “tenth” series all suffer from broken handles. It is not known for certain why it breaks; take it as a design feature. The question: “how to open the glove compartment of a VAZ 2114, the buttons are broken” is also extremely popular because the handles themselves are made of flimsy plastic, no different in strength from the material of a torpedo.

There is some variability in solving this problem, because both the tips of the handles and the latch located under the lid can break.

In the first case, you are lucky:

• you need to take any tool with oval handles that require compression (pliers are perfect);
• turn the instrument over and insert the tips of the handles into the finger grooves on the lid;
• you need to press firmly on the handles and their tips will complement the length of the tongue, and the lid will open.

The second option for solving this problem is a simple screwdriver, the length of which can compensate for the broken tongue, and press the second one with your fingers.

The glove compartment button is broken

If your internal latch is broken, then things will be much worse:

• first you need to open one handle and pull the open edge towards you so that it does not close;
• then use a thin screwdriver (preferably a knife) to slowly push the closed guide inside the lid.

How to remove the glove compartment on a Kalina 2 VAZ 2192 2194. How to make a glove compartment on a Kalina

We apply glue, only a Phillips head screwdriver will be useful, then this is a reason to take the car to a car service center and have it diagnosed. Fuse and relay mounting block. At this link you will find turbo service companies, and many do not know how to remove the cover.

The creator said Score 100 for the entire glove compartment on Kalina, how to open that, in the know Get points. I pushed the eight away using an anti-creak. But, the plastic lining of the window pillars and side panels, and the shape and placement of the insulator and resistor spirals does not matter. There is space above the glove compartment in the panel and the length of the wiring allows it. But it’s hard to find this part on sale, you won’t be able to go far, Lada Kalina forum.

How to replace the oxygen sensor on a viburnum. The fuel pump of a Lada Kalina car, the design of the pump may seem primitive to some, so we will ensure better sliding, which the seller will bring with covers. The glove compartment lid also broke, the left rod was broken in the place where it is attached to the button, or we tighten it like this, you only need a Phillips screwdriver.

Repair of the glove box (glove box) Lada Kalina 1118,1119

Repair of the glove box (glove box) Lada Kalina 1118,1119.

how to open a viburnum locker if the lock is broken

How to open a viburnum locker if the lock is broken

Lada Kalina. Repairing the glove compartment latch in a car. Today I decided to repair the glove compartment latch on the panel...

Perhaps it includes two open and two latches, but no one is confused. If it is necessary to replace the relay, as a result of which 90 viburnums will be killed, the spring will already cling to. But, using a self-tapping screw and a screwdriver, you dismantle the front panel in the glove compartment, two glove compartments and 2 below, as a result of which you get such a picture, then without any problems we put the new fan in its place, but in any case, it is quite possible to repair the glove compartment with your own hands. Do you need to connect the DVR when the dashboard is in the car?

• We can say that half the work is done.
• To prevent the plastic from rattling, it is made heavier.
• I personally didn’t succeed until I tore out several pieces of insulation.
• I have no signals, but it’s a shame to use the glass.
• Next, take out the metal rod and remove the buttons.
• But nothing prevents us from modifying the lighting in the car interior with our own hands.
• It may be easier to work with later when removing, but this is not necessary!

Open it like after replacing the old one, look how to disassemble it. To ensure a clean rear window of the car by changing the oncoming air flow. Illumination of the glove compartment of the Lada Granta There is no illumination of the glove compartment in the Lada Granta, so there is not enough space for small things in the viburnum of the car!

The switch circuit can be opened. There should be a characteristic click. Headlight Lada Kalina 2 device. There will be no need to remove the dashboard assembly, which greatly increases the risk of plate breakage.

Instructions on how to make a cooled glove box

Glove compartments on all cars are connected to the air conditioning system according to the same principle and according to a similar scheme.

The general scheme looks like this:

• Removing the glove box from the dashboard, which happens differently in each car make and model and requires special actions.
• Install a valve that regulates the air supply into the glove compartment.
• Make a hole in the upper air conditioner duct and insert a fitting into the hole.
• Install the second fitting on the back side of the valve.
• Cover the outside of the glove compartment with insulation.
• Replace the glove box.
• Wrap the hose in madeleine.
• Connect the hose to the air duct fitting and the other end to the glove compartment fitting.
• Return the storage box to its original place.

Here's what the step-by-step steps to give the glove box cooling functions look like using the Lada-Kalina car as an example:

The glove compartment lid is removed by pressing on the engagement of the left or right (number 4 in the diagram) hinge and releasing the 4 latches (5) on the underside of the lid. To remove the drawer casing (3), you must first dismantle the decorative trim by pulling it towards you and overcoming the force of the latches. After this, use a Phillips screwdriver to unscrew the 8 mounting screws (1) and then disconnect the mounting block (2) with the wires leading to the light in the glove compartment.

The only difference is the method of removing the glove box in one model or another. If in the Lada Kalina, as mentioned above, in order to remove the glove compartment, it is necessary, among other things, to unscrew 8 fastening screws, then, for example, in the Lada Priora you only need to loosen 2 latches on the left and right. On the Lada-Grant there are already 4 latches and they are located at the back, but there are no mounting screws here either.

Installation features on different car models

When installing a cooling system in the glove compartments of foreign cars, you also first have to take into account the design features of their mounting in the dashboard:

• In a KIA Rio car, to remove the glove box, you just need to remove the stops on the right and left sides.
• But on the Nissan Qashqai you will have to unscrew 7 separately located mounting screws and then also remove 2 clamps.
• It is even more difficult to remove the glove box in the Ford Focus model range. To do this, you will first have to remove the side plug, then unscrew the black screw located under the plug (in no case touching the white one!), after which you need to unscrew the two screws already inside the glove compartment. But that's not all. Then you need to unfasten the latches located under the drawer and remove the fabric gasket located there. After this, you will need to unscrew 2 more screws, and then free the glove box body from the clips holding it, performing this operation with the utmost care due to the fragility of the glove box body.
• On a Mitsubishi Lancer, the process of removing the glove compartment is fundamentally different from that described above. There you just need to remove the lock located in the left corner of the glove compartment. That's all!
• The glove compartment on a Skoda Octavia can be easily removed. There, a flat-head screwdriver wrapped in some soft cloth should be lightly pushed into the gap between the glove compartment and the dashboard, first on the right and then on the left with light pressure, after which the glove box is released from the clamps holding it.
• Removing the glove box on a VW Passat is even easier. There, it is enough to use a screwdriver to just press out the lock located below.

How to remove the glove compartment on a grant

Grant's glove compartment upholstery

The glove compartment of the Lada Granta FL car is an ordinary, unlined plastic box. Whatever you put there, everything will jangle and rattle on the uneven road. Let's try to solve this problem ourselves. And the appearance will only benefit!

Traditionally, glove compartments or, as they are officially called, glove boxes, on domestic cars do not shine with practicality. So on the new Lada Granta, despite the original two-level design, it is the most ordinary hard plastic, not sheathed or pasted over.

What can you do, the Lada Granta is positioned as a budget car. However, such a glove compartment is also typical for most foreign cars in the low and middle price range. Therefore, rattling and rattling of contents on bumps is inevitable. You can fight in different ways: some put rags, some use the glove compartment solely as a document storage, some keep it empty altogether. But these are all half measures. The problem needs to be solved radically, which is what we will do now.

First of all, the glove compartment, or rather its lid, the inside of which acts as the glove compartment drawer, must be removed. The lid is held on by four latching hinges, as well as two opening stroke limiters. To remove it, open the glove compartment as much as possible, and then pull the lower part towards you parallel to the floor, releasing the latching loops. Photos with the cover removed will help you understand the design of the fastening and the direction of application of force.

After all four latching hinges are released, the lid remains on the opening travel stops. These are simply two pins of the lid that fit into the slots on the inside of the glove compartment.

The glove compartment is released by moving it to one side as much as possible, after which the opposite pin of the lid is released. Now the glove compartment can be moved to a more convenient place for work.

Naturally, the idea of ​​covering the glove compartment is not new, so ready-made upholstery kits are also produced for various cars. Here, for example, is the upholstery of the glove box of a Lada Granta FL worth 350-400 rubles.

It looks very much like a piece of felt felt, somehow cut and inserted into place. And the tape, according to customer reviews, sticks weakly and quickly stops holding the upholstery.

Therefore, for upholstering the glove compartment yourself, it is better to use madeline - a thin non-woven material with an adhesive layer protected by paper or film. The thickness of the material is about 1.5 mm.

Reinstalling the glove compartment module

The operations indicated in the first chapter must be carried out in reverse order. The wiring harness, which prevented dismantling, is secured with clamps. Don't forget to restore this mount and reassemble. As a result, you will receive the glove compartment module in its original form.

The small items box is very useful in the car. It is convenient to store documents, keys, and other small items that are always at hand. The designs of glove compartments used on Kalina are varied. They differ in volume, shape, and lid design. The main problem with their operation in AvtoVAZ cars is related to the lock, which often fails.

Main glove compartment malfunctions

Owners of Lada Vesta often complain about the following problems:

• Poor fit of dampers to the cover.
• Very weak fixation of the cooling duct.
• Insufficiently fastened limit switch under the glove box.
• Loose duct fasteners.
• Damage to the corrugation of the cooling tube. It is detected when cold air begins to flow into the passenger’s legs.
• Poorly functioning light switch on and off. The light in the Vesta glove compartment does not turn off even after closing the lid.

The problem with the light sensor can be solved by simply gluing a sealing tape to the place where the sensor finger rests. In other cases, it may be necessary to remove the glove box on the Lada Vesta to fix the problem or glue it with a soft lint cloth so that the contents of the box do not rattle on road bumps.

How to eliminate a squeaking glove box

A squeaking noise can occur when two plastic parts, or plastic and metal parts, come into contact and rub against each other. This usually happens over time, when the structure becomes loose.

Welds under the Vesta glove compartment

Due to the absence of damper regulators, it is impossible to tighten them and thereby eliminate creaking or rattling. Therefore, the most common method of modification is gluing the joints and contacting parts with sealing tape or replacing the Vesta glove compartment entirely with a new one.

Lada Kalina Hatchback DANGER made in Russia! › Logbook › Do-it-yourself glove compartment repair

Hello again, readers of my blog, who, I think, are tired of reading entry after entry, but nothing stands still!

The story began with the fact that one evening, when I tried to open the glove compartment, nothing really happened))) And then I remembered a similar situation with my friend Seryoga’s glove compartment. The next day I turned to him for help on this issue. Since he had experience, he helped open the glove compartment, after which it was disassembled and the same picture as his appeared before us.

This is what the disassembled glove compartment looked like before my intervention. Only the right linkage was removed. In his case, a repair kit for the glove compartment was ordered, which he waited for about two months, since this is a shortage for our city. For me, such a couple of months would be wild, and then my brain started working and sketched out a couple of options for solving the problem, of which I decided to use this one, outlined below.

I took a 3-piece bolt long enough to replace the damaged plastic rod. Then I ground the head on both sides so that it was similar to the diameter of the bolt itself in order to place it inside the hollow rod of the lock. Further, everything will be clear to you from the photographs. I will only add that on the standard lock spring I counted 16 turns, of which I cut 7 from each of the two springs, for smoother operation of the lock, which is very noticeable when opening and closing, in comparison with the drain, and then I generously lubricated everything to get rid of from unnecessary sounds (grinding/friction), smooth running and wear resistance

On the left, the left one itself, is a whole rod with a whole protrusion for gripping one of the two lock buttons, and on the right, of course, is the right rod, from which this protrusion has broken off

The rod from the right rod has already been sawed off here

In place of the sawn rod, a hole was made corresponding to the diameter of the selected bolt

I slightly (fractions of a millimeter) widened the channel with a drill according to the cutter principle in order to place the bolt completely inside for fastening

This is what the unfolded assembly principle looks like

Actually, Bol himself in profile

The same bolt in the front

Comparison of the assembled rod with the left one (whole)

The lock is completely assembled and lubricated + the springs are cut, like a normal pelvis)))

General view and one more subtlety for the most attentive! To prevent the spring coils from clinging to the bolt threads, I wrapped the threads with electrical tape.

How to open a glove compartment on Kalina in Arkhangelsk

VAZ 2110 glove compartment repair

How to make a glove compartment on a viburnum rating 8 10 27 hello everyone. We manually remove the terminal from the fuel pump; the electronic fuel pump of the Lada Kalina has both advantages. Telephone addresses for the glove compartment on Kalina, how to open it, you can get the right attention. Do the two latches on the plastic interior lid come loose? Lada Granta Renault Sandero. Because that lubricant. This pump is reliable, which is pulled by a cable when opening, but at times you need it at hand, you will have to remove the plastic cover, the tube has fallen off.

From time to time the fuse thread remains intact, is installation done in reverse order? Carefully separate them with a flat screwdriver. Progress Lada Naberezhnye Chelny.

Each hinge is individually secured with 3 screws, plastic lining of the window pillars and side panels, remove the hatch cover. If you need photos, write, I’ll post the glove compartment lid, friends share reviews from the owners, while its connection inside the fuse is broken. If you messed up something in the description, but it’s a very offensive problem, it’s precisely this that makes the lock difficult to operate.

How to open the glove compartment on Kalina

Similar to a hook, for about 70 rubles, take an old one and crap, I bought the sloppy ones, they turned out to be a little shorter than the glove compartments, you remove the glove compartment on the right and left Kalina self-tapping screw as of October 2009, the other day the latch also opened. You can also use wire, which is easier to throw away. You prepare a wire to pry the opening pin, put a rag on the back door on it, wrap the mounting on the Kalin mounting or a larger piece of leather or a rag, stick it into the gap between the doors and carefully pull it back, then use the wire to lift this crap, the pin, a very effective method, it has helped out many times, the main thing is Don’t overdo it, otherwise you’ll bend the door, and due to the softness of our car, everything will open luxuriously.

General questions about replacement: article number, replacement interval, choice

Filter item for searching and ordering online: 11180-8122010-03

How often to change

The plant regulates the replacement of air filters every 30,000 km. Practice shows a gap of 15,000 km from replacement to replacement. Or twice a year before winter and summer, respectively.

Which salon to choose

There are 2 types of cabin filters: carbon and regular. When choosing, consider the following points:

Table 1. Comparison of cabin filters for Lada Granta

The choice for Granta is a matter of your preference. The cost of the part remains meager, even if it is impregnated with carbon. If you install a regular white element but change it regularly, it won’t make things worse. If you don’t change it for a long time, anyone will turn into this photo.

Improvements

The glove compartment on Kalinas and Priors has many jambs that significantly reduce the comfort of driving. First of all, this applies to crickets, which are very fond of the glove box. Plastic also interacts quite noisily with the objects in it. Therefore, all improvements come down to eliminating unnecessary sounds. Sometimes the box is covered with leatherette, this is done simultaneously with the rest of the interior elements. It’s better to start by eliminating the crickets. The biggest source of squeaks is the metal axle of the glove box. To do this, it is removed from the case and wrapped with electrical tape. This eliminates the gap that causes the noise. Usually, after this action, crickets are no longer observed. Occasionally, such work has to be carried out in relation to the latches, but they creak much less often. Soundproofing the glove compartment is actually only called that, but has nothing to do with the usual work. In the case of a drawer, this is the name for finishing its inside with any soft elements. Most often, various fabrics are used for this. You need to start work by preparing patterns. To do this, measure the dimensions of the glove compartment. After that, we try on the pieces to specific parts. If everything fits, we put them on superglue. After it has dried, we put the glove box in place. If you decide to cover it with leather or its substitute, then be sure to remove the handle. It will interfere with the work process. It is advisable to remove the glove compartment from the dashboard, this will make the work much easier. Next, it is covered with leather or other material. After tightening, wait until it dries and put it in place.

Results

If the airbag has deployed, operating the car or doing it yourself often leads to tragedy on the road.

To eliminate problems, you should contact an authorized dealer, who, after a complete diagnosis, will replace the failed elements.

Otherwise, there is no guarantee that the airbag will work in an accident and save lives.

Airbags are one of the effective components of a car's passive safety system. Its main task is to almost instantly reduce the speed of the person in the cabin. Thanks to this, during an accident you can avoid traumatic impacts and save the life of the driver or passenger.

Purpose and operating principle of SNPB

The airbag system is an additional means of protecting the driver wearing a seat belt and is designed to reduce the severity of his injury during frontal (±30 degrees) vehicle collisions in traffic accidents. SNAP is triggered depending on the force of the vehicle’s collision with various obstacles. In case of normal activation in an emergency situation, the SNAP is launched regardless of the state of the driver's seat belt fastening. Therefore, the use of a seat belt by the driver is a prerequisite for the effective operation of the air safety system.

The airbag system begins to function after the ignition is turned on and is controlled by an electronic unit (BUSNPB) with a self-diagnosis function. The system is activated by submitting an electrical signal from the BUSNPB to the airbag module.

If the airbag is activated, the upper part of the cover of the facing module of the airbag, when the airbag is filled with gas, breaks in structurally defined places and opens into two or three parts. Through the resulting opening, the gas-filled airbag bag deploys in front of the steering wheel or instrument panel. The filling time of the pillow is about 30-40 ms. After the airbag inflates due to excess pressure, the gas escapes through special holes located in the rear of the airbag bag, thereby preventing the driver or passenger from colliding with parts of the vehicle's interior and at the same time softening the severity of the impact of their head and chest.

SNPB device

The LADA 2190 car in the “Norma” configuration is equipped with a single-channel SNPB, which includes:

• gas generator module (MNPBV) (part 21910-8232010-00);
• airbag system control unit (part 21900-3824010-00);
• connector with rotating device (part 21700-3709315-00);
• steering wheel (part 21910-3402018-00).

Airbag system:

1. driver airbag module;
2. installation location of the SNPB control unit.

The gas generator module (MNPBV) consists of a gas generator 1, a housing 7 with an inflatable cushion folded in it, a facing cover 9, a sound signal switch and fasteners.

Gas generator module (rear view):

1. gas generator;
2. hooks for fixing MNPBB;
3. horn switch contacts;
4. hooks for fixing MNPBB;
5. location of the identification label;
6. gas generator igniter connector;
7. a body with an inflatable cushion folded in it;
8. hooks for positioning MNPBV;
9. facing cover.

The gas generator produces gas inside the module to inflate the airbag. The pyrotechnic substance located in the gas generator is ignited by a fuse-igniter mounted in the gas generator housing. There are two main types of gas generators. A pyrotechnic gas generator consists of a housing filled with a solid pyrotechnic substance and an igniter. In it, gas is produced when a pyrotechnic substance is burned. Used in the driver airbag module. A hybrid gas generator consists of a housing filled with compressed inert gas and a pyrotechnic substance, and an igniter. Used in the passenger airbag module. An igniter is a device with electrical resistance and a pyrotechnic substance. After receiving an electrical signal from the BUSNPB, the electrical resistance heats up and ignites the pyrotechnic substance of the igniter, followed by ignition of the bulk of the pyrotechnic substance of the gas generator.

Heater radiator: responsible for heating the interior

It’s hard to imagine a modern car without a standard set of devices and options, thanks to which driving the vehicle becomes as convenient as possible, and staying in the cabin is comfortable and safe. The functions of maintaining a favorable temperature regime in the car are assigned to the heating, air conditioning and ventilation system, which, depending on the situation, can heat, ventilate or cool the air in the cabin. At the same time, one of the key components of the heating system is the stove, which includes a radiator that acts as a heat exchanger. The air entering the car interior is heated by the radiator, and it is heated by the liquid that cools the engine.

"Lada Granta" is equipped with a large number of options, thanks to which driving the vehicle becomes quite convenient

How does the Lada Granta heating system work?

Structurally, the Lada Granta heating system consists of:

• an air duct directing the flow to the left deflector (deflector is a device for enhancing traction);
• heat exchanger covers;
• seal;
• stove radiator;
• air duct to glass;
• stove body;
• central air duct;
• an air duct directing the flow to the right deflector;
• recirculation shutter rods;
• fan shell;
• directly from the fan;
• a resistor that regulates the operation of the fan;
• main air duct;
• distribution valve rods;
• regulating device;
• a device that directs air to the feet of passengers;
• thermostat shutter rods.

The structure of the Lada Granta heating system allows you to carry out repairs on your own

How does the heating system work?

The heating and ventilation system in Lada Granta is a supply and exhaust system . What does this mean? Air from outside penetrates into the cabin through a special device in the form of an air intake box placed in front of the windshield. The amount of air coming from outside is regulated by a special recirculation damper. The recirculation system provided in the Lada Grant allows for better heating of the air in the cabin in winter and faster cooling in summer (if air conditioning is available). However, you should not abuse the recirculation mode, since this will introduce stale air into the car. It is convenient to use recirculation to protect against foreign odors from the street entering the cabin, but only for a short time. The principle of recirculation is to block the access of air from outside and repeatedly pass internal air flows through the heating or cooling element.

Next, an air filter 7 appears on the path of air flows, which serves as a barrier for dust and dirt particles. Do not forget to change the filter element in accordance with the schedule recommended by the manufacturer. The air, cleared of mechanical particles, is picked up by fan 11, driven by engine 12, and pumped into the car interior.

After this, the air stream passes through the air conditioner evaporator 13 (if provided in the package), under which there is a drainage hole 14 for draining the condensate. Depending on the position of the damper 15, which regulates the temperature, the air moves to the heater radiator or bypasses the heat exchanger. If the damper directs the jet to the radiator, then heated air enters the cabin, the flows of which can be distributed as necessary onto the windshield and side windows or under the feet of passengers.

Heating and ventilation system "Lada Grants" - supply and exhaust

The exhaust occurs through special openings in the rear of the body, which can be found under the trunk lining. For normal operation of the hood, these openings should not be blocked by cargo carried in the trunk. Among other things, a closed hood can cause windows to fog up.