The gearshift lever on a VAZ 2110 is loose

Even ardent supporters of the Russian automobile industry cannot help but be annoyed when the gearshift lever on a VAZ 2110 dangles; moreover, it also produces the most unpleasant rattling sound. Those with stronger nerves put up with it as an inevitable “side effect”; some even got used to constantly holding the gear shift knob with their own hand.

Gear lever

However, this cannot continue forever, especially if the vibration gets to the point that the lever begins to miss when shifting gears, confusing second with fourth and third with fifth. But in order not to take the situation to an extreme, let's talk about what to do to avoid rattling the gearbox handle.

↑ Disassembly procedure

Loosen the clamp on the gearshift drive rod using 13mm wrenches, and remove the hinge from the rod.
Then we remove or bend the corner of the boot, and using a 10mm wrench, unscrew the locking bolt on the cardan and knock it off the shaft with gentle blows of a hammer.

This bolt is very reluctant to turn off, since it is mounted on a thread lock to avoid spontaneous unscrewing due to vibration.

At this stage, you can also replace the gear selector shaft oil seal if oil leaks are noticed from under the old one.

Determining the cause

So, while accelerating or idling, your gear lever is shaking like crazy, making an annoying rattling noise. But no other faults related to the gearbox were found. What could be causing this?

Causes of chatter:

An engineering miscalculation by the creators of the VAZ 2110. They simply forgot to think about the fact that the metal bushing for connecting the lever to the rod “clings” to the edge of the rod while driving, which is why rattling occurs;
You have tuned the lever using a Lada Kalina. This replacement brought you several positive aspects, and one that was not very pleasing. When the car is in motion, vibration occurs in the driveshaft from Kalina, which transmits rattling through the traction of the entire mechanism. Many who have carried out such tuning claim that even if the lever is removed altogether, it still does not eliminate rattling;
The retaining spring could have broken, or it might not have been there at all. In this case, rattling is inevitable;
Often the VAZ 2110 gearshift knob rattles due to wear on the engine and gearbox mounts. It is also possible that other parts responsible for eliminating chatter (damping vibrations) have worn out.

If the gearshift lever dangles, and difficulties of various kinds arise when shifting gears, then a little tuning will not help here; repair and adjustment is needed not only of the handle, but also of the gearbox itself.

↑ Installation of a new part

When the old part is dismantled, you can begin installing the new one.

Having first put on the boot, we place the cardan on the gear selection rod (the one that comes from the box). In this case, the fixing bolt must, when screwed in, fall into a special recess under it on the rod.
Then tighten the bolt and pull the boot onto the cardan. It is highly advisable to coat the bolt thread with thread locker so that it does not unscrew due to vibration.
Then we put the gearbox shift drive rod on the cardan rod, but do not tighten the clamp yet.

Someone may have to shorten the Kalinovsky cardan shaft by about 1.5 cm, since it is longer than the standard one.

What to do if the gearshift lever on a VAZ 2109 and 2110 is loose? Everything can be corrected

Owners of domestic cars are interested in what to do if the gearbox lever of a VAZ 2109 and VAZ-2110 is loose.
This problem is known to almost everyone who has been the proud owner of such machines. Moreover, the reasons why this malfunction occurs are the same in both models. After all, their gearbox is identical. It manifests itself as follows. First, play appears when changing gears. A little later it intensifies, and a ringing sound is added to it when moving. Over time, the backlash turns out to be so large that it becomes almost impossible to get into the desired gear. Therefore, it eliminates the breakdown in advance, before the backlash becomes huge. Main reasons

What to do if the gearshift lever on a VAZ 2109 and 2110 is loose?

To answer this question, it is necessary to determine the reason for this behavior of the lever. There may be several reasons. Some of them are caused by the design of the car and are practically unavoidable. The problem with a dangling lever and rattling occurs for the following reasons:

Designer error. The metal bushing clings to the rod when moving. The result is a rattling sound. There is no way to solve this problem;
Bushing failure;
Lever from Lada Kalina;
Malfunction of the backstage cardan;
Wear of the box or its fastenings.

Each of these reasons leads to play in the lever. The first reason only gets on the nerves with a rattling sound, but there are no problems with controlling the box. To determine the reasons, you will have to carefully inspect the car in the pit. In some cases, you will have to make repairs or modify parts.

Bushing failure

. The bushing holds the lever in a certain position. It receives almost all the effort when changing gears. Over time it may burst. In this case, the lever will move much more freely, but at the same time, gear shifting will occur, as a rule, without any problems. To fix it, simply replace the bushing.

Lever from Lada Kalina

. On Kalina the box has been slightly modified. When installing a lever from it on a regular box, the driver receives several positive bonuses. The disadvantage of this tuning is the appearance of play in the lever and constant rattling noise when moving. The problem arises from the lack of a softening spring on this arm. To fix the problem, you need to take a standard spring from the nine and attach it to its usual place. To secure one end of the spring to the levers, you will have to make fastenings. For this you will need welding.

Malfunction of the yoke cardan

This is one of the most common problems. At the same time, eliminating it is quite strange. Backlash occurs as a result of wear of the cardan parts. This happens regularly. Therefore, in order to save time, it is better to buy and install a sports version or from Kalina. Such cardans last much longer. When installing a “original” part, be prepared that you will soon have to change it again.

The part needs to be changed in an inspection pit or overpass. First you need to loosen the clamp on the drive rod. You will have to use an open-end wrench size 13. Next, the hinge is removed from the rod. The boot is turned away and we get access to the cardan.

It is secured with a locking bolt. To remove it you will need a 10 mm wrench. It is advisable to use a clamp used for brake pipes. Otherwise, there is a risk of crushing the edges. The fact is that domestic engineers came up with an ingenious way to avoid unscrewing the screw during vibration; they put it on glue. After struggling with the bolt and unscrewing it, remove the cardan. After which a new part is installed and reassembled. The correct assembly is indicated by the position of the latch; its head should be completely in a special recess.

Wear of the box and fastenings

Often lever play occurs due to a faulty box. Most often this is due to the fastening of the scenes. When the mechanical part wears out, the free play of the rocker and, accordingly, the lever increases. Often this problem first appears in some gears, but over time it spreads to all speeds. Therefore, if play appears, make sure that the gearbox is in good condition. If repairs are required.

If the lever does not dangle, but at the same time during movement it vibrates, making a rather unpleasant sound. The reason is most likely in the mountings of the pillow. If they are damaged, the gearbox begins to vibrate. Which in turn is transmitted through the scenes to the lever. This can be treated by replacing the box mounts.

Conclusion

. There are not many reasons for lever play. Some of them are created by the drivers themselves. For example, replacing the original lever with a part from another model. There are several answers to the question of what to do if the gearshift lever on a VAZ 2109 and 2110 is loose. How to eliminate a problem in a particular case directly depends on the reasons that caused it.

↑ Adjusting the gearshift lever VAZ-2110

Now you need to adjust the position of the lever. To do this, we involve an assistant who sits in the driver’s seat and moves the gearshift knob to the optimal position for adjustment. Typically the lever is centered and moved slightly to the right. In this position of the lever, we tighten the clamp while the assistant holds the lever in this position.

Now all that remains is to check the correct operation of the gear shift lever, and if something is not satisfactory, you need to make the adjustment again.

Basic faults of the gear shift lever and repairs

As a rule, drivers are faced with the fact that during operation the lever can:

difficult to move (requires a lot of effort);
The gearshift lever begins to dangle, making it difficult to work with;
the gear shift lever creaks;

Please note that if any problems occur with the gearbox lever, you must immediately stop using the vehicle and restore functionality.

The fact is that driving a car with a faulty gearshift lever is extremely dangerous, since in certain situations the inability to timely select and turn on/off a gear can cause an accident, etc.

As a rule, the lever stops working normally for two reasons:

mechanical breakdowns or natural wear and tear of individual elements;
malfunctions resulting from too much force applied, damage to the lever, etc.

You can check the gearbox lever, as well as, in some cases, repair it yourself. First of all, normally the gear shift knob should move freely. Jamming is not allowed. If the lever moves with obvious difficulty, there is a high probability of failure of the spherical washer or ball joint. These elements need to be changed.

Another temporary measure is sometimes to apply a thick lubricant, which manages to neutralize the squeaking of the gear shift lever. By the way, creaking also often indicates wear of the above elements. Let's add that if the gears switch off on their own, you will need to check the spring, which may jump off. To solve the problem, the spring is simply put in place.

Repairing the gearshift lever itself often involves replacing failed elements. In this case, the lever will need to be removed. To access the plastic bushings and axle, you must first remove the shift lever boot.

To remove the lever, the plastic protective plate is dismantled, then the hinge cage is released. Next, you will need to move the jet rod to the side, after which the entire lever is completely removed.

We also recommend reading the article about why reverse gear does not engage. In this article, you will learn about the main reasons why you cannot engage reverse gear.

You will also need to check how the axle moves. If the movement of the axle is not hampered in any way, the bushings will need to be replaced (before installation, all replaced elements must be lubricated with grease).

To replace the spring, this element must be pulled out. To do this, the locking ring is removed, as well as the hinge with the lever. If it is necessary to replace the ball joint, carefully move the spherical washer apart with your fingers, after which you can remove the worn element. When installing a new support, the part must be lubricated in advance.

If you need to replace the rods, you will need to locate the clamp from underneath the car. The specified clamp will need to be loosened, and then disconnected from the hinges. Now you can unscrew the fastening nut and remove the rod. After installing a new rod, assembly is carried out in the reverse order.

After replacing all elements and lubrication, the lever should move smoothly and clearly, without dangling, which allows you to comfortably and quickly select and engage gears. Also, if necessary, it is periodically necessary to lubricate and adjust the gearshift lever, linkage and other elements during vehicle operation.

Disassembly

In order for the vibration of the VAZ 2114 gearbox handle to cease to exist, you need to have a couple of tools in reserve:

Socket wrenches 13 and 10
New drawstring cover
Overpass or pit in the garage
A smart friend who will help you tune the stick
You can stock up on thread locker, but you can do without it (this thing is attached to the side of the box itself).

It will take a little time, about half an hour to eliminate troubles and the same amount to adjust.

First way

Progress of the adjustment process:

Sketch, remember, remove or measure, but make sure that after installation everything is in its place: namely, at a certain distance from the passenger and the console.
Now you can crawl under the car and begin to unscrew the fasteners for inserting the bushing into the lever tube (also called the rocker) using a 13-socket, and remove the lever.

Backstage VAZ 2114

Then, remove the cover from the cross. Be prepared for oil to pour out. You can put the container in advance if you really feel sorry for him. Then pour it back. Well, unscrew its fasteners to remove it.

Drawstring without cover for VAZ 2114

That's it, now we need to install a new clamp - this is the bolt that secures the cross. You can, of course, clean and tighten the old one, but it is not so expensive that you need to save on it. And new things always inspire greater confidence in the future.

We will put the actions in the opposite direction with some deviations:

After putting the stick in place, inserting the bolt and tightening it, putting the cover in place, you need to engage 4th gear. This will drive the bushing into place - into the rocker (lever).
Then, put it in neutral. This is where a friend comes in handy: he places it, and you tighten the fasteners. At this moment, you can adjust the position of the stick, move it in the desired direction under you.
Well, then try the result. If you are not satisfied with how the gear knob is positioned on the VAZ 2114, you need to bring the adjustment to fruition.

Second way

The second reason for the rattling is the bushing, which is located on the lever itself. In order to get rid of this nasty sound you just need:

Open-end or socket wrench 13
New bushing
And a little patience

The process itself will also take no more than half an hour. The work itself will have to be carried out in the interior of your car. The action plan is:

To get to the bushing, you need to remove the skin from the gear knob.

Gearbox lever VAZ 2114

Using the wrench you have, unscrew the nut and pull out the bolt.

Unscrew the nut on the VAZ 2114 gearbox lever

We take the handle out of the rod.

We take out the gearshift lever of the VAZ 2114

We change components.

Gearbox lever bushing components for VAZ 2114

We assemble in reverse order.

Is it worth fixing the problem?

Many people don’t even try to fix the gearshift lever of a VAZ 2114, but this task is completely solvable, it doesn’t require skills, and the undeniable advantages are worth an hour of time. The difference is so noticeable that if a breakdown has been present in your life for a long time, you will constantly remember that there is not enough noise.

The main thing to remember is that a machine is like a person, what “cured” one is not the fact that it will help the other, and don’t get upset. The repair will take very little time, you can get away with a small sum, and in return you will receive a number of huge advantages, such as:

the unpleasant sounds accompanying the increase in speed will disappear;
the gearshift lever will be fixed;
switching will become smooth;
At idle, the lever will stop “dancing the lambada” under your hand.

Where does the vibration come from?

In this article we will popularly understand where the legs “grow” from and what to do. As expected, this is a mistake by the VAZ design bureau, sometimes it is the result of “tuning”, but we will consider all the reasons in detail, as well as methods for solving the problem. Possible options:

When moving, the bushing connecting the lever and the rod first begins to rub and then hit the edge of the rod. This vibration creates this sound. This is a pure engineering miscalculation, the length of the sleeve is worked out incorrectly, its length is longer than necessary and it is this extra edge that catches.
Replacing the lever with a Kalinovsky one, here the rattling comes along with the positive effects of the replacement. Due to the imperfection of the design, Kalina's driveshaft produces vibration, which is subsequently transmitted to all structural elements. The vibration and sound remain even without the lever.
The retaining spring is broken; the first symptom is that the VAZ 2114 gearbox lever dangles freely in neutral gear, absolutely not fixed in the position between third and fourth. If the problem suddenly appears, then the spring is to blame, and only repairing the gearbox will help here, otherwise the remains of the spring will break the entire box, then it will be really expensive.
Sometimes this occurs due to general wear and tear of the car's shock absorbing parts, gearbox mounts and engine.

Car owners put off the problem until forever “later”, due to lack of time and money, but it’s worth knowing that the repair procedure is inexpensive, done with your own hands, and costs very little.