How to connect a windshield wiper motor

Frame or frameless, which is better to choose?

The consumer has always been faced with the question: which wipers to buy - framed or frameless. Both types have their pros and cons. Let's look at which windshield wiper blades fit the size of the Lada Granta, indicate the article numbers and manufacturers. This will help when choosing, so as not to make a mistake by a couple of extra centimeters.

Review of frameless wipers on Lada Granta

Let's start with frameless ones:

1. Bosch (3397118907). This company produces windshield wiper blades for many cars. For Lada Grants, they are available in lengths of 600 and 400 mm. Like the entire line, they clean very well, are durable and do not scratch the glass surface. This product is manufactured in Belgium.
2. SWF (119840, 119860). The main production is located in Poland and France. SVF is a subsidiary of Valeo, which is known for its high-quality spare parts. The length and type of fastening are ideal for the Lada Granta.
3. Horse is a domestically produced windshield wiper for the Lada Granta, the size of which is 600 and 410 mm, which is completely suitable. There is one caveat: to install them on a car you will have to use an adapter for a hook.

Review of frame wipers on Lada Granta

1. Bosch (3397004673, 3397004667). This is an inexpensive substitute for the frameless option from a world famous brand. They run well, don't creak and last quite a long time.
2. Bosch (3397010297). This is another inexpensive option for brushes, where a pair is already combined in one package, 60 and 40 cm long.
3. Champion (A60/B01, A41/B01). They have a metal frame and are considered a premium class among frame wipers.

There is also a third option for windshield wiper blades on Granta - these are hybrid ones. They are manufactured by Denso (060L, 040L). These are frame wipers that are covered with an aerodynamic casing. The pricing policy for such brushes is average between frame and frameless, so they are considered more affordable. In terms of technical qualities, they are in no way inferior to frameless brushes.

Where is the wiper relay located on the Granta liftback?

Many motorists are faced with the fact that their windshield wipers periodically stop working properly, suddenly turning on or off. In 95% of cases, the reason lies in the relay - regulator. It is located under the dashboard on the left side. For access with subsequent replacement, you will need to unscrew the plastic cover and remove the relay. Next, replace it with a new one and close the plastic case again.

The Grant liftback rear (front) wiper relay has several pause modes. This is very useful for reducing the frequency of cleaning when there is light rain. The pause range varies from 1 to 65 seconds. The driver independently regulates the most optimal mode. Catalog number: 723.3777. The product is completely identical to the relay on the VAZ, Priora, Kalina, Kalina 2 models. On VAZ models produced before 2001, a relay with four contacts is installed, unlike the new ones, which have six.

How to choose the correct wiper size?

For the Lada Granta model, regardless of its level of equipment, windshield wipers have identical sealing parameters: 600 mm for the product installed on the driver’s side and 410 mm elements on the passenger side. We talked about the fact that the size of the wipers needs to be chosen carefully.

Now there are products on the market from unscrupulous manufacturers. These entities indicate the standard parameters of the blades on the packaging, but the packaging contains products whose wiper blade sizes differ from the declared values. To avoid an unpleasant moment, it is necessary to invite the seller to jointly measure the actual parameters of each of the brushes in the kit for the LADA Granta model.

If the buyer purchased components with a parameter that differs from the regulated value, then there is a risk of poor quality cleaning of the glass after installation. This is due to the varying degrees of down force created by the wiper, which depends on the size of the wiper blades. If there is a specimen with an overestimated length, then its clamping value will be greater, which will negatively affect the service life of LADA Granta glass. On the contrary, windshield wiper blades with a shorter length do not have sufficient pressing force, which will negatively affect the quality aspect of cleaning.

What are the causes of breakdowns?

The most likely factor causing the wipers to stop is the blown working element in the fuse. Eliminating this malfunction involves performing the simplest action - replacing the fuse link. It is located in the corresponding mounting block, located on the left side of the steering column. It will be useful to stock up on a fuse diagram, which will help you easily find the insert we need.

When the purifiers stopped functioning intermittently, the control relay most likely became unusable. This component is also located in the previously designated block. When a relay fails, it is replaced with a new analogue. However, we note that according to numerous reviews from owners of domestic small cars, certain statistics have been formed indicating the small number of cases of breakdowns of this kind.

The most common cause is the destruction of bushings. They are made of plastic, so they do not boast a long service life, which reaches a maximum of three years. The process of destruction of elements is primarily influenced by the quality indicator of the material. Here, the only effective measure is replacement, and to carry it out you should acquire a repair kit, which is available at a specialized retailer. In this case, the trapezoid is replaced.

Types of windshield wiper blades

After establishing the authenticity of the wear of the windshield wiper blade and the reasons that led to it, we head to the store. Traders are able to offer a lot of options for these products, but in general they are divided into two categories:

• frame;
• with no frame.

These groups of brushes for Lada Granta have significant differences. Frameless options are able to adhere more tightly to the glass surface, which provides better cleaning quality. These products are not so susceptible to freezing. They also create a relatively less noise effect while driving (at speed).

Frame elements also have a number of advantages.

1. They are more gentle on the glass surface because they have less pressure.
2. If the glass geometry has an increased bend, like the LADA Granta, then this type of wiper blades is capable of cleaning a much larger area compared to a frameless competitor.
3. Lower price of these designs.

The cost of the brush replacement service is identical and does not depend on the type of product design used.

Methods for connecting windshield wipers.

The connection diagram for windshield wipers can be divided into two types, depending on the method of connecting the operating mode switch.

In the first connection method, a constant plus is supplied to the wiper drive electric motor, and the mode switch connects the motor elements to the minus. This method is widely used in foreign and domestic cars.

The second method is completely opposite to the first, that is, power is supplied to the electric motor through the mode switch, and the minus in this case is taken from the drive housing.

I propose to consider the principle of operation of a car windshield wiper circuit using an example, where plus is supplied to the electric motor through a mode switch, since this is the more common connection method.

The diagram shows the connection of a windshield wiper drive with an electric motor powered by permanent magnets and having two operating speeds. The difference in speed in this circuit is ensured by the displacement of one of the positive brushes relative to the physical center of the electric motor armature.

When is it necessary to replace wipers?

Replacing windshield wiper blades on Lada Granta is seasonal. Like many global automobile manufacturers, Lada recommends changing wipers twice a year: before winter and after the spring season. But, there are signs that the windshield wiper blade is already deteriorating.

Signs of bad wipers

Let's take a closer look at these factors:

• Cloudy glass. Of course, this may be the cause of poor windshield washer fluid, but in some cases, only replacing the windshield wipers that have a buildup that prevents them from cleaning the glass properly will help.
• Lots of stains and uncleaned areas. Usually, the reason for this is wear on the rubber bands of the brush.
• Vertical uncleaned stripes. This is more of a frame-type disease of windshield wipers. The reason may be deformation of the frame itself or wear of the rubber bands.
• Narrow stripes. In this case, it is the wear of the rubber bands.

Possible causes of problems

Some experts argue that if the windshield wiper blades do not work when turned on, then the most common reason for this is a failed fuse. In this case, no special efforts will be required to fix the problem. You just need to open the fuse box cover (on the left under the steering column) and find the appropriate fuse. A diagram printed on the inside of the lid will help you do this.

If the wipers do not work intermittently, then the relay may have failed. It is located in the same place as the fuses. It needs to be replaced with a new one. But, as statistics provided by owners of Lada cars show, fuses or relays blow out quite rarely.

A very common reason why the Lada Kalina windshield wiper blades do not work is the destruction of the bushings. As experienced drivers say, plastic bushings fall apart very quickly - their service life is at most 3 years.

Perhaps the reason for their destruction is the quality of the plastic. But, alas, there are no other bushings. The repair kit can be found in specialized auto stores.

When the wiper drive does not work, the reason may be a failure of the motor that drives them. To find out whether the electric brush drive has really burned out, you need to check whether electricity is supplied to it. This can be done using a tester. If power is supplied, then the overheated motor needs to be replaced.

Frame, frameless, combined

What a “frame wiper” is is clear to everyone: the design of the unit uses a metal frame. The role of the frame can be performed by a narrow strip made, for example, of plastic. And then the structure is called frameless (see figure). By the way, the plastic itself can differ in rigidity, and it is also sometimes reinforced.

Three types of wipers

Hybrid or combined designs use a frame and a plastic strip (bottom picture). In general, a hybrid differs little from a frame wiper: the height is reduced, other characteristics are the same. So, there is no need to delude yourself about the use of “hybrid wipers”.

Winter brushes

If tourmaline is added to rubber, such material will be good at removing oil films. And if the wiper frame is covered with a cover, this will protect the structure from ice. This means that, in general, winter brushes are frame brushes with a plastic cover.

“Winter wipers” can only be frame ones

And for some reason it is believed that it is necessary to clean glass from oil products in winter.

The disadvantages of winter windshield wipers are listed below:

• Availability of a frame (required);
• Increased weight of the structure;
• High price.

In theory, any winter brush is also suitable for summer. The main thing is not to use frameless brushes in winter, since they are not intended to fight ice.

The many faces of U-Hood

Some brushes compatible with the U-Hood (J-Hood) mount have a tricky lock: to loosen the mount, you need to bend the lever. This lever itself is difficult to notice right away (Fig. 1).

To tilt the lever at least to some angle, you must first squeeze two buttons (Fig. 2). So, the sequence: squeeze the buttons, tilt the lever.

Tips for choosing brushes for Granta-liftback

After selecting the product model you like, we recommend paying close attention to its quality aspects. To implement this action, we arm ourselves with the following methods

1. The smell. An original and high-quality product is devoid of such a bright property as smell, or the factor manifests itself to a very insignificant extent. Counterfeits and China reek of an unpleasant odor.
2. Wiper blade size and flexibility. Quality windshield wiper blades are not overly flexible. If this point (slight flexibility) is present, then purchasing such “devices” is not recommended.
3. Manufacturer's marking. All brand products have this marking located directly on the surface of the part. Chinese false analogues do not have this property.
4. Appearance. The quality of design of original products (coloring, the same markings, etc.) is always at its best. If there are defects (crooked fonts, uneven coloring, etc.), then this is direct evidence of the presence of a counterfeit product.

Types of wipers

There are two types of wipers for the Lada Granta:

1. Frameless. Such products are better pressed against the surface of the windshield, which allows for better cleaning. Due to the absence of a frame, such devices practically do not freeze during the frosty season, which greatly simplifies their operation in winter. In addition, when operating at high speed, frameless products produce an order of magnitude less noise.
2. Frame. This option is older, since it was previously widely used on many cars. Their cost is lower, but they are equipped with a frame, which in any case will freeze during cold weather. However, products of this type tend to cause less damage to the surface of the windshield, since they are not pressed against it as tightly, unlike frameless options.

There is also a hybrid version of the product, but it has the same characteristics as frame wipers, so we do not recommend choosing it. The most technologically advanced option is frameless products, but their cost is higher (the author of the video is the remgar channel).

Rear window wipers

Malfunctions in the operation of rear window wipers are usually associated with the steering column switch, gear motor, power wires, broken drive teeth, and worn brushes. The relay does not affect the operation of the rear wipers, so its malfunction can be ruled out. The methods for eliminating other breakdowns are the same as for the front wipers.

Repair of windshield wipers mainly comes down to replacing damaged components, cleaning electric motor parts, cleaning and lubricating moving joints, and straightening deformed levers. Repair costs are low, and using contract spare parts from JapZap will keep them to a minimum. The procedure for dismantling and installing different components of this assembly may differ in different cars, but the general principles for troubleshooting are the same.

How to troubleshoot purifier malfunctions yourself?

When the owner of LADA Kalina turns on the windshield wiper drive, the motor works, but the wipers refuse to move, then the bushings will have to be replaced. For this purpose, the trapezoid of the wipers is dismantled, which is covered by a decorative plastic panel. The location of the unit (trapezium) is directly under the windshield. Repair of the windshield wiper is carried out using the windshield wiper trapezoid repair kit in the following order:

• unscrew the fasteners of the brushes and remove them together with the leads;
• then we dismantle the decorative protection panel, for which we stock up on a Torx T20 wrench;
• we move on to removing the trapezoid itself, which is held on the frontal body element by means of a nut and a pair of bolts, using, if necessary, a repair kit for the windshield wiper trapezoid;
• Next, you will need to disconnect the supply lines of the unit from the battery;
• Now you can remove the assembly.

If you resort to replacing the bushings without removing the trapezoid, you create a risk of deformation of the hinges, which will lead to incorrect operation of the brushes. A destroyed bushing will immediately give itself away, so we boldly proceed to the “operation”. The element is removed using wire cutters. Before installing the new bushing along with the lock washer, you will need to preheat it in boiling water, which will allow you to easily slide the specified element onto the hinge. Also, before installing the ring, lubricate the bushing with a suitable substance, for example, lithol.

How to remove the trapezoid assembly

Before proceeding with the removal, it is necessary to remove the wiper arms, as well as the plastic lining at the very bottom of the windshield, which I wrote about in the instructions for replacing the Kalina cabin filter. There you will need just TORX T20.

After these pads are removed from the car, you can begin to unscrew the bolts and nuts securing the trapezium itself. First, unscrew the bolt on the left, as shown in the photo below:

Then in the center:

And you also need to unscrew one nut on the right side, it’s best to use an open-end wrench there:

Now there is nothing holding the trapezoid and now you can tilt it slightly forward:

To remove it from its seat:

And in order to finally remove it, all that remains is to disconnect the power plug of the motor. It was not possible to photograph everything in its original form, but there is nothing complicated there - bend the latch and pull the plug towards you. You will also need to remove it from the hole in the body in which it is mounted on a latch (clip). Here it is after removal:

Operations for removing the gearmotor from a Lada Granta car

1. Disconnect the wire from the negative terminal of the battery.2. Remove the windshield wiper mechanism (“Removing and installing the windshield wiper mechanism for Lada Granta”).

3. Check the position of the trapezoid rods: they should be located on the same line. If this is not the case, set the rods to the required position, otherwise after removing and then installing the gearmotor, the trapezoid crank will take an incorrect position on the axis of the gearmotor.

4. Mark the relative position of the gearmotor shaft and crank.

5. Loosen the crank nut with a wrench and unscrew...

6. Remove the crank from the gearbox shaft

7. Remove the three bolts securing the gear motor to the windshield wiper...

8. ...and remove the gearmotor.

9. Install the windshield wiper motor in the reverse order of removal, aligning the marks made during removal. Lubricate the linkage joints with grease before assembling. Before installing a new gearmotor, it is necessary to adjust it (set it to the end position). To do this, do the following: - connect the wiring harness block to the gearmotor; - place the gearmotor in the opening of the air intake duct; - connect the wire to the negative terminal of the battery; - close the hood; - turn on the ignition; - turn the windshield wiper to the operating position for 10-20 seconds and then turn it off - the gear motor will be installed in its extreme limit position.

Sources

• https://new-granta.ru/dvorniki-lada-granta/
• https://avtozam.com/vaz/lada-granta/razmer-dvornikov/
• https://www.autosecret.net/lada-granta-vaz2190/127-ustrojstvo-i-remont-lada-granta/jelektrooborudovanie-lada-granta/1350-motoreduktor-dvornikov

Also check out

1. Remove the plastic plug, unscrew the 2 nuts to “13”, then the wipers with their leads.

1. Remove the frill using a TORX T20 socket. Perhaps some of the bolts will be covered with plugs.

1. Using a “10” wrench, unscrew the nut on the right side and the 2 fastening bolts securing the trapezoid to the body, and then on the left side.

1. Disconnect the negative terminal of the battery, disconnect the connector and the trapezoid with the wiper motor.

1. Install a new trapezoid. Reassemble everything in reverse order. At the end of the work, adjust the cleaner brushes.

Replacement

The replacement procedure is simple. It is carried out in just a few steps:

• the leash is moved to a perpendicular position - in relation to the stack being cleaned;
• You need to clamp the brush on both narrow sides and pull it towards the hood, down;
• With gentle rocking, you need to pull the brush out of the hook in which the rotation axis is located.

If the brush is no longer used in the future, dismantling can be done with a jerk. In this case, the plastic clamp will most likely break. Installation is performed in reverse order

It is important to remember: plastic becomes brittle in the cold. Freezing temperatures can cause it to break.

It is important to carefully study the installation method.

Dimensions

The overall dimensions of both generations of cars are identical. It should be noted: AvtoVAZ purchases ready-made brushes from Bosch. After which it carries out installation directly on the conveyor. Uses original packaging for products made in Germany. Therefore, you can safely purchase brushes from other manufacturers.

It will not be possible to find original ones made in Togliatti. The standard size is 410 mm on the passenger side, 600 mm on the driver’s side. The first generation car was released in a sedan body. Wipers are shown only on the windshield. The second generation was released in a liftback body. There is a rear wiper

It is important to note: its length is 300 mm. Installation of a longer wiper is allowed

Up to 350 mm. More than this length, the brush will begin to touch body parts. You can figure out which ones are better with the help of a specialist.

Original articles

It is possible to purchase original parts. But this does not make sense: AvtoVAZ packages contain products from other manufacturers. The article number allows you to find the brush on the Bosch website. It is worth noting that the quality of such parts is great. From the assembly line, cars are equipped with frameless models.

Original articles:

Replacement options

It is not difficult to purchase high-quality brushes in the store - analogues. It is only necessary to note: it is worth choosing parts from well-proven brands. All presented modifications can be divided into categories:

• frame;
• frameless;
• hybrid;
• winter.

Frame

They are a classic design

An important advantage is low cost. The downside is the low contact ability at high speed

After 80 km/h the brushes practically stop cleaning. The reason is simple: the air flow lifts the cleaning surface above the glass. Which leads to poor contact. As a result: precipitation and dirt are not removed from the car.

Frameless

They are a good alternative to classic solutions. But it should be noted: they cost a little more. The brush itself is made from a single piece of rubber. This allows the air flow to easily flow around the structure. Therefore, even at a speed of 140-190 km/h, there are no problems with cleaning. But frameless brushes are characterized by low strength.

Hybrid

Hybrid ones do not have the disadvantages of frame and frameless brushes. But they have their advantages:

• good aerodynamics;
• stylish design;
• strength.

Like frameless ones, they are made from a single piece of rubber. But there is a metal structure inside. Making the brush more rigid. This allows you to worry about damage without worrying. These models are distinguished by their durability. Even with intensive use, they will survive 2-3 seasons.

Winter

Winter wipers are distinguished by their elasticity - even at sub-zero temperatures they clean the glass well. The secret of this effect is simple: rubber contains rubber. Its main feature is that at low temperatures it does not lose its flexibility. Maintains elasticity. Winter brushes are a good solution for those living in the Far North or areas close to it.

When purchasing brushes, you need to focus on the following factors:

• weather in which operation is carried out;
• driving speed – if the car accelerates over 100 km/h, then frameless, hybrid brush models are purchased.

To avoid such a difficult choice, some car owners simply carry several pairs of wipers with them at once. If necessary, changing frameless to frame and vice versa. Winter brushes allow you to avoid frostbite on the glass and the formation of plaque on it. Models designed for the summer season will not cope with low temperatures.

Trouble-shooting

Poor quality of glass cleaning is usually associated with wear of the cleaning tape, as well as contamination of the hinges in the frame brushes and limited mobility of the rocker arms. The easiest way to solve this problem is:

• In frame brushes, the cleaning tape is changed. The brushes must first be dismantled, the worn element removed, a new one installed in its place, secured with steel plates and the brush secured to the lever.
• Frameless brushes are replaced entirely.

Sometimes the tape is in good condition, but the brushes leave streaks because the grooves that hold the tape are clogged. In this case, they should simply be cleaned. If the metal frame is covered with rust and the rocker arms have lost their mobility, it is better to replace the brushes entirely.

Cleaning tape is inexpensive, but some motorists are in no hurry to change it. You can restore the elasticity of the tape by dipping it in gasoline and washing it with a warm soapy solution; after this procedure, it is useful to coat the tape with silicone grease. Traces of grease are easily removed with white spirit. A worn, rounded edge can be smoothed out using fine-grit sandpaper glued to a hard base.

Slow movement of the wipers may be due to:

• With wear of the gear motor. It must be disassembled, cleaned, lubricated, and if critical wear occurs, replaced.
• With corrosion, contamination, insufficient lubrication of moving joints. The entire mechanical part is dismantled, disassembled, cleaned, and lubricated.
• With an error made during the installation process that needs to be identified and corrected.

Incorrect assembly can also cause the wipers to not return to the park position. Another reason for this problem is wear or breakage of the drive splines, in which case they need to be replaced.

Problems in the operation of the electric motor can be associated with both its breakdown and mechanical problems. If the gearmotor itself is damaged, it is best to replace it entirely. But if the problem can be fixed by replacing the damaged gear, cleaning the dirty manifold, and adjusting the limit switch, replacement can be avoided.

If the engine does not turn on, you need to inspect the power wires, winding wires, commutator, brushes, as well as the steering column switch, which includes a wiper switch.

• Damaged power wires are replaced with intact ones, oxidized tips are cleaned.
• A failed switch is replaced.
• A dirty collector can be cleaned, the internal cavities can be blown out and the surface can be sanded.
• If the collector burns out, it is better to replace the gearmotor.
• Replacing the gearmotor is also recommended if the winding wires are broken, although only the armature can be replaced.

The engine shutdown due to the fuse tripping may be caused by a short circuit in the winding; in this case, the gearmotor must be replaced. But quite often, an emergency shutdown is associated with the locking of the brushes due to their freezing to the glass, deformation of the levers, or the entry of a foreign object into the mechanism. In this case, the cause must be eliminated. Frozen brushes are carefully separated from the glass using a scraper so as not to damage the cleaning edge, but it is better to wait until it thaws. The mechanism is cleaned of dirt and foreign objects that hinder its operation. Deformed drive elements are leveled, and if the deformation is severe, they are replaced with new ones. After eliminating the cause of the fuse tripping, the blown disposable fuse is replaced with a new one, and the thermobimetallic fuse can be used again.

Intermittent purifier problems are most often caused by a damaged relay or switch. If the brushes move intermittently without pauses, and everything is in order with the relay, the limit switch may not operate. In this case, you need to adjust it, bend the contacts or the spring plate, which the gear cam bends. It is also possible that the limit switch contacts are dirty and need cleaning.

Recommendations for selection

Let's consider several product manufacturers:

1. Frameless Bosch Aerotwin. Belgian-made products are equipped with native fastenings; the main advantage is a long service life, as well as aerodynamics and the absence of extraneous sounds during operation.
2. SWF VisioNext - also of the frameless type, equipped with a hook type mount. The products are manufactured by Valeo, which also produces many other types of components and parts for cars.
3. Bosch Twin Spoiler frame brushes. Dimensions fit standard Granta windshield wipers. Despite the fact that the products are frame, they are quite reliable and have a long service life.
4. Champion Aerovantage. This manufacturer has been on the market for quite a long time, during which time it has been able to win the trust of many of our compatriots. The products belong to the premium segment of the market and are equipped with a steel frame.

Price issue

The cost of products depends on their quality, performance and manufacturer. Average prices for some windshield wiper models are shown below.

Types of wipers for Lada Granta

Domestic VAZ models can be equipped with one of three types of windshield wipers:

• frame;
• hybrid;
• frameless.

By default, frame type is installed from the factory, as the most economical option. However, this design is short-lived and ineffective due to rapid wear and deformation under the rays of the sun. The basis of the brush is a metal strip with movable arms and a rubber cleaner.

The hybrid version of the wiper differs from its predecessor in that it is smaller in size and low-slung. The frameless model is made of impact-resistant plastic with a rubber seal at the end.

The non-contact option is considered the most effective, with a long service life and good adaptation to temperature changes.

There is a fourth type of brushes - winter ones. They are designed for use at sub-zero temperatures. The structure at the base is sealed with an additional layer of plastic. There is a special ledge on the surface for removing snow and ice from the windshield.

The method of fixing all four types is “J”-shaped. Previous modifications had an excellent mechanism, which is considered outdated and ineffective.

Alternative sizes

It is clear that they are trying to increase the size of the brushes, not decrease them. Let's look at what happens as a result:

• 60 x 40 is the most common option;
• 65 x 40 is a good alternative. The “triangle” at the bottom between the brushes will be reduced to the limit;
• 60 x 45 – use this option only if you are installing frameless frames;
• 65 x 42.5, frameless – remove the “triangle” completely.

Probably, the reader managed to understand the main idea: the total length of the brushes should not exceed 105 cm. In the latter version, by the way, one “wiper” can come into contact with another. In practice, this does not happen, since the “left brush” is located above the “right”.

When do windshield wiper blades need to be replaced?

There are several signs that indicate that the purifiers need replacing:

1. The primary and most important is poor windshield cleaning quality, the appearance of streaks and streaks when fluid is supplied from the washer reservoir. As a result of wear of the blades themselves installed on the wipers, the quality of glass cleaning is reduced to a minimum. Poor cleaning results in obstructed visibility.
2. The appearance of noise and squeaking when the wipers operate. As a rule, extraneous noise appears after the brushes begin to wear out and the glass is poorly cleaned. But there are also cases when the sound appears first, and only then the ineffectiveness of the brushes. So if you notice squeaking or noise, keep in mind that you will have to change your wipers soon.
3. The glass began to darken. As a rule, darkening of the glass is caused by the use of a low-quality washer, but the reason may also lie in damage to the rubber blade. This will cause the angle of the wiper edge to be offset.
4. The windshield wipers seem to “jump”. As a result of an increase in lifting force, the following problem appears - the wipers begin to work faster, and accordingly, they can jump over some areas of the glass surface.

Video “Features of replacement”

How to replace cleaners without a puller and what you need to take into account - learn from the video (author - AssistanceTV channel).

Windshield wipers, better known as windshield wipers, are not vital vehicle systems. But their breakdown causes serious inconvenience in bad weather and threatens traffic safety due to poor visibility. Fortunately, most windshield wiper malfunctions can be fixed fairly quickly with your own hands; repairing them is much easier than, say, repairing an automatic transmission.

Windshield wipers, better known as windshield wipers, are not vital vehicle systems. But their breakdown causes serious inconvenience in bad weather and threatens traffic safety due to poor visibility. Fortunately, most windshield wiper malfunctions can be fixed fairly quickly with your own hands; repairing them is much easier than, say, repairing an automatic transmission.