For attaching windshield wiper blades
Currently, various types of fastenings are used.
This is usually due to the desire of manufacturers to make extra money on spare parts, although some mounting options are significantly smaller than others, which improves the aerodynamic resistance of the brushes and improves appearance. Until 1999, most automakers produced cars with standard windshield wiper mounts - a “hook”
. This type of fastening is currently the most common. In 1999, Ford equipped its Taurus with a new mount, and then almost all automakers began equipping their cars with various “tricky” mounts. Until recently, Japanese manufacturers refrained from such steps, although the first cases have already occurred - for example, Nissan Quashqai, Honda Civic and Mazda 3.
Car windshield wipers, commonly referred to as “windshield wipers,” are one of the consumable parts of all cars. They serve to remove water and dirt from the surface of the windshield, and sometimes also the rear window, that interfere with visibility. Since blades from different cars are not fundamentally different from each other, replacing windshield wipers is done the same way for all cars. Let's look at how to change them with your own hands.
Replacement
The process of replacing old windshield wiper blades with new ones does not cause serious problems
It is only important to carry out all actions carefully, not to break the plastic fastener included in the kit. The replacement process includes the following steps:
lift the wiper up, it is fixed in this position - perpendicular to the windshield;
Next, you need to take the brush body in your hand and squeeze it, then move it down - slight swaying will simplify the procedure;
then the brush is simply removed from the lever.
The installation process is performed in reverse. Many brush models are supplied with special adapters.
They must be used carefully. Plastic is usually fragile
If it is damaged, it will be impossible to install the brush in place. What will lead to the impossibility of using it?
When choosing a brush, it is important to focus on the brand. To date, Bosch, Champion and Denso have proven themselves well.
It is important to replace brushes in a timely manner, since road safety directly depends on this. Otherwise, precipitation falling on the windshield simply will not be removed in time
Rear wiper — Lada Kalina Station wagon, 1.6 l., 2014 on DRIVE2
I almost never use the rear wiper, but from the first days of owning the car I was haunted by the realization that the rear wiper, due to its flawed design, is, in principle, incapable of wiping anything off the glass. The first attempt to fix this was made a year ago and consisted of replacing the standard brush with a frameless one (even in my deep youth, someone gave me a pair for my penny, but they didn’t suit her terribly, so they have been lying in the garage ever since). This did not change the situation with pressing the brush to the glass and I somehow cooled down, it lies there motionless in its place behind and let it lie. But the other day I once again came across someone’s post about replacing the standard leash with a leash from 2111 and decided to change it too. I ordered on existential “VAZ2111 rear windshield wiper arm” 63.5205800 for 243₽, I found in the garage an adapter from the same blade for a small hook, to replace it you simply unscrew the nut on the cap, the old arm is removed from the axle with a little force, the new one is put in its place and tightened the same nut. The 2111 leash itself is slightly shorter than the standard one, so the cleaning zone has shifted by 3 cm to the axis of the windshield wiper, the pressure of the rubber band to the glass has increased significantly, the glass cleaning is excellent.
Upd: by the way, for those who want a more modern look, there is a good option from Kia/Hyundai, part number 98810-07001, it is a little shorter of course, but not critical and costs about 500 RUR complete with a brush.
Price: 243 ₽ Mileage: 63850 km
What to look for when choosing?
It is no secret that the level of visibility to the rear depends on the efficiency of the brush, which is especially important when maneuvering in cramped conditions and in bad weather. When choosing, you should lean toward high-quality branded products that will not subsequently emit an annoying squeak when rubbing against the glass and do not have to think about how to remove and replace the wiper. You should also inspect the integrity of the working element of the brush, which initially should not have cracks or breaks. An important role is played by the force with which the rear wiper is pressed to the surface of the glass, as well as the material from which the product is made.
Possible malfunctions and how to eliminate them?
Intermittent operation of the rear wiper mechanism is a very common situation faced by owners of the Lada Kalina station wagon. The solution is simple - you need to replace the fuse. It is located in the mounting block, which in turn is located under the panel to the left of the steering column. Sometimes a replacement requires a relay, which can be found in the same mounting module.
When the rear windshield wiper completely refuses to function after activating the button, then diagnostics of the electric drive of the LADA Kalina station wagon will be needed. The wiring goes to the electric motor itself. Here you need to make sure that the contact at the ground terminal is reliable. In most cases, the problem is eliminated by simply cleaning the contacts from oxides. If such manipulations do not give the desired result, disassembling the mechanism and probably replacing the motor will be required. Sometimes the culprit for the lack of purifier functionality is the steering column switch.
Removing and disassembling the windshield wiper motor
All the important parts of the rear windshield wiper are located under the trim. To remove it, I had to tinker, since it was attached to special holders, which are not so easy to remove without special tools. Fortunately, I had a nail puller at hand and it was perfect for removing these fasteners.
After unscrewing the rear wiper mount, I unscrewed the mount of the motor itself. I disconnected it from the block and took it home for inspection.
There appears to be no damage. Then he unscrewed the mount of the motor housing and pulled the structure out of it. The mechanism itself is covered in lubricant; there was plenty of it.
When is it necessary to replace windshield wipers in Kalina?
Over time, owners of practical Lada Kalinas notice the appearance of brush marks on the surface of the windshield. Such “artifacts” create an obstacle to good visibility. In this situation, the indicated components will need to be replaced, and the trapezoid will likely need to be replaced
Many experienced owners advise purchasing frameless brushes, which, in their opinion, are able to “bravely” withstand temperature changes and can demonstrate a relatively longer service life of approximately 1.5 million cycles
Before replacing, you should understand the required size of the products. For Lada Kalina, you should purchase a driver's side brush with a length of 600 mm, and for the glass area opposite the passenger - 400 mm. For stern glass, the brush has a standard parameter of 360 mm. This wiper needs to be replaced much less frequently, since the intensity of its work is significantly lower compared to the front components.
The wipers are tired — Lada Kalina Universal, 1.6 l., 2014 on DRIVE2
I apologize for such a title, but there’s no other way to say it, but that’s putting it mildly. Like many owners of the second Viburnum, I’m not satisfied with the quality of cleaning the windshield; I’m generally keeping quiet about the rear one for now. Not only do standard brushes creak, but they also don’t clean them, leaving behind streaks and stains. Believe me, I’m not being picky, on the first Kalina everything was just super. Well, I think the problem will be solved by purchasing frameless brushes. How wrong I was... I bought it, installed it and... returned it, because... on the passenger side there was an uncleaned area right in the middle. Damn. I went online to see if anyone has the same problems. It turned out I'm not alone))).
My next attempt was to buy leashes from Kalina-1. Externally, the brush holders are not very different, but the length of the spring on the Russian leash is twice as long.
No comments necessary
I have already prepared a camera to share my happiness with dvukalinovodami. But another bummer came out: the leash on the driver’s side began to touch the plastic trim near the windshield with a metal wire and lift up the rubber seal. I started looking for differences, it turned out that the angle of the Russian leash was different, I decided to return it, not without problems, but they accepted it back at the store. Therefore, my advice is to check the brush holders without leaving the cash register. Maybe, of course, I came across a bad option, but I think that they are not suitable for LK2 without modification. Today I solved the problem by purchasing Bosch FRAME brushes... and lo and behold, I’m happy with everything. Nothing creaks, nothing remains on the glass.
bosch brushes
And don’t tell me after this that frameless ones clean better. Fact, not always and not on all machines. Apparently the windshields of LK2 have some kind of fantastic convexity that they do not lend themselves to frameless ones. IMHO
PS I managed to find a leash from K1 and take a photo of it in comparison.
On top is a leash from K1 at the bottom of K2. The height is different from the base. Result - the bracket touches the seal
Price: 280 ₽ Mileage: 1300 km
What are the causes of breakdowns?
The most likely factor causing the wipers to stop is the blown working element in the fuse. Eliminating this malfunction involves performing the simplest action - replacing the fuse link. It is located in the corresponding mounting block, located on the left side of the steering column. It will be useful to stock up on a fuse diagram, which will help you easily find the insert we need.
When the purifiers stopped functioning intermittently, the control relay most likely became unusable. This component is also located in the previously designated block. When a relay fails, it is replaced with a new analogue. However, we note that according to numerous reviews from owners of domestic small cars, certain statistics have been formed indicating the small number of cases of breakdowns of this kind.
The most common cause is the destruction of bushings. They are made of plastic, so they do not boast a long service life, which reaches a maximum of three years. The process of destruction of elements is primarily influenced by the quality indicator of the material. Here, the only effective measure is replacement, and to carry it out you should acquire a repair kit, which is available at a specialized retailer. In this case, the trapezoid is replaced.
If the owner of a Lada Kalina discovers that the wiper drive is not working, this indicates that the unit’s motor has failed. In order to verify this fact, you will need to make sure that voltage is supplied to the motor contacts from the on-board network. This procedure is easily performed using a regular tester. If there is power, then we definitely change the motor.
Advantages and weaknesses of wipers
Each type of brush has certain advantages, and at the same time, both product options are not without disadvantages. Frameless versions have great durability, because for their production manufacturers use high-quality rubber and weather-resistant plastic. Over time, although the rear brush wears out, this process is not intensive.
In operation, frameless brushes for the Lada Kalina station wagon do not emit unpleasant squeaks and do not greatly rub the surface of the rear window. Also, the products adequately withstand the onslaught of temperature changes.
Now the disadvantages. There is only one point here - it is overpriced.
In addition to the metal base, frame brushes have plastic structural components that are integrated into the frame itself. Cleaners are low-cost and widely distributed in the retail chain.
Among the disadvantages of frame options, one can highlight their small resource. After a couple of years of use, the working elements of such a brush become unusable and require inevitable replacement. A constant companion to the work of the wiper is an annoying squeak.
Possible causes of the malfunction and ways to eliminate them:
When the windshield wiper is on, the electric drive does not work:
Fuse blown:
- remove the cover located to the left of the driver, under the steering column, under it there is a mounting block;
- on the cover of the mounting block there is a diagram of the location of the relays and fuses of the car, we find the required fuse and change it if necessary;
Relay fault:
If the wipers on the Lada Kalina do not work intermittently, you need to change the relay located in the mounting block, next to the fuses.
Wiper motor malfunction:
- we check the ground terminal of the electric motor, screwed to the car body next to the rack;
- we clean it and the attachment point;
- install in place;
VAZ 1117 If this does not have a result, disconnect the connector for the electric drive of the windshield wiper, located under the windshield frame.
Using a tester or any other continuity test, we check whether power is coming to the connector. If power comes in, then it is necessary to change the wiper motor.
Disconnect the terminals from the battery. Remove the decorative caps from the leashes. Unscrew the nuts securing the leads and remove them. Remove the plastic grille under the windshield frame by unscrewing the bolts that secure it. Having unscrewed the trapezoid fastening (two bolts and one nut), remove the electric motor from the box and disconnect it from the trapezoid. We install a new one, repeating the procedure in reverse order.
If power does not come to the connector, the steering column switch must be replaced. Disconnect the battery terminals. Remove the plastic steering column cover. Disconnect the switch block and, pressing the latches on both sides, remove the steering column wiper switch. Install a new one by repeating the process in reverse order. Assembling the casing.
When turned on, the wipers on Kalina do not work, but the electric drive rotates
It is necessary to check the condition of the gearbox and wiper trapezoid.
Unscrew the plastic grill under the windshield frame. First remove the wiper arms and unscrew the nuts that secure them. We check whether the gearbox axis of the electric windshield wiper drive rotates.
If the axis rotates and the trapezoid is stationary, check the splined connection of the gearbox and trapezoid, and if necessary, tighten the fastening nut. If the connection is severely worn, it is necessary to replace this unit.
If your windshield wipers on your Lada Kalina do not work, this is not a reason to despair. As a rule, the cause is a minor malfunction. Such as a blown fuse or a loose nut on the spline connection between the gearbox and the windshield wiper drive, which can simply be tightened.
The windshield wiper electric drive system is quite reliable and does not require special maintenance. It is enough to follow basic operating rules. If during the winter period the wipers are frozen to the windshield, then before turning on the windshield wiper, it is necessary to free them from ice. And they will serve you without causing any problems.
Removing the windshield wiper mechanism completely is quite an easy job, for this we need 10 by 13 heads, a ratchet, a knob, a 10 and 13 ring spanner, you can also use an open-end wrench.
First of all, you need to get down to work on removing the wiper arms and plastic linings; detailed information on removing the plastic linings can be read here: Replacing the cabin filter on a Lada Kalina.
If you have sorted out the removal of the plastic covers, we proceed to the process of unscrewing the trapezoid mounting bolts. First, unscrew it on the left, as shown in the picture.
Then in the center.
After this, unscrew the nut on the right side; for this it is better to arm yourself with an open-end wrench.
Now there is nothing holding the trapeze, you need to slightly tilt it forward.
We take it out of the seat.
The final step when removing is to disconnect the power plug of the motor. To do this, you just need to bend the plug lock and remove the plug. First you need to disconnect it from the body; the plug is attached to a clip.
Removing and installing the windshield wiper motor on Lada Kalina
The motor is connected to the trapezoid by 3 bolts and one nut. So we unscrew the 3 bolts using a 10mm socket.
After this, unscrew the nut securing the trapezoid and the motor shaft.
You can remove the motor, since there are no more fasteners.
If there is a need, we replace the trapezoid or motor and assemble it in the reverse order.
If the rear wiper of the Lada Kalina 2 does not clean well (the reason is the leash, not the brush)
07 April 2016 LadaOnline 39 286
Hatchback and station wagon cars are considered more practical, but sometimes they can have their own specific disadvantages. For example, on the new Kalina, the rear wiper does not press as hard as on the first generation models, which is why the wiper blade does not clean the rear window well, leaving uncleaned areas. Let's look at several ways to solve this problem.
Installation of wiper arms from Lada Kalina 1
The difference between the rear wiper arms is the length of the spring. On the new Kalina, the spring is short and is not able to press the blade firmly enough against the rear window. The design allows you to install on Kalina 2 a wiper arm from Kalina 1, catalog numbers:
- Rear windshield wiper arm Kalina station wagon - 1117-6313150;
- Rear wiper arm Kalina hatchback - 1119-6313150.
To change the leashes, first remove the old one by unscrewing the nut, and then install the new one, that’s it!
Modernization of wiper arms for Lada Kalina 2
It is not always possible to buy a wiper arm for the first Kalina; in this case, the design can be modified. It is necessary to remove the leash and tension spring. Then drill a new hole in the metal bar of the lever closer to the brush. We install the spring using a screwdriver, clinging it to the new hole. Now the tension will be stronger, which will allow the rear wiper to clean the glass better.
Result on video:
By the way, another way to solve the problem of poor cleaning of the rear window is to install a frameless wiper. Let us remind you that the front wiper blades can be installed in larger sizes.
Photo: logbook iosif-waitberg and c0de
Keywords: Lada Kalina windshield wipers | Lada Kalina accessories
1 0
Found an error? Select it and press Ctrl+Enter..
Similar materials
- What size of wipers (windshield wipers) is better to choose for Lada Priora
- Removing the rear light and replacing lamps Lada Kalina 2
- What size to choose for Lada Granta, Kalina 2 wipers
Do-it-yourself troubleshooting
To do this, you need to remove the trapezoid, which is located under the plastic decorative trim under the windshield. Windshield wiper repairs are carried out in the following order:
- unscrew and remove the windshield wiper blades along with the leads;
- unscrew and remove the plastic cover, for which you will need a TORX T20, or “star”;
- unscrew the trapezoid, which is attached to the car body with a nut and two bolts;
- disconnect the windshield wiper drive from the battery;
- remove the trapeze together with the drive.
If you do not remove the trapezoid, then when installing the bushings you can bend the hinges, which will lead to improper operation of the wipers. Therefore, it is better to remove the entire trapezoid and replace it not with weight, but with emphasis.
The destroyed bushing is immediately visible. It can be simply removed using wire cutters. To insert a new one, it and the locking ring must be steamed in hot water, otherwise it will not be possible to put it all on the hinge. Before putting on the locking ring, the bushing should be treated with lubricant (for example, lithol). All disassembly and assembly work takes a maximum of 40 minutes.
But if the central bushing “flies”, then most likely the entire windshield wiper mechanism will have to be replaced. Replacing a windshield wiper trapezoid is an even simpler task than the process of removing and installing new bushings. All work is carried out according to the algorithm described above.
Naturally, a complete replacement of the windshield wiper trapezoid will cost more than repairing the windshield wiper. But it will be more reliable. New ones are almost guaranteed to last longer than refurbished ones. Although some Lada owners claim that a rebuilt and repaired Kalina wiper trapezoid can easily last two years. Well, you should always base it on whether you are willing to spend time or money.
Video “How to replace a trapezoid and a motor with your own hands?”
The procedure for replacing these devices of the windshield wiper system on Kalina is given below (author - channel In Sandro's garage).
Because You are not logged in. To come in.
Because you are not a trusted user (phone number is not verified). Enter and confirm your phone number. Read more about trusts.
Because The topic is archived.
Are the rods the wiper arms or the leash?
Do I hit the brushes on the counter? ¶
Well then everything is clear.
https://www.youtube.com/watch?v=https:tv.youtube.com
It’s just that before replacing, you should have noticed the position of the gearbox shaft on the trapezoid body, you didn’t do that, and that’s why this shit happened now ¶
