It is difficult to imagine how much fuel a car “consumes” over the entire period of operation. And all this volume passes through a small device - a fuel filter. Renault Megane is available in several versions. Depending on the engine size, the design of the cleaning device also differs.
If we take Renault Megane 2, the year of manufacture of which does not exceed 2007, then the filter element (fine filter) is installed under the bottom of the car next to the rear wheel on the driver's side. Thus, Renauilt designers have achieved convenience when replacing this unit.
Models that have exceeded the 2007 year of production are mounted inside a unit with a pump and sensor
The third gasoline generation of Megan is no different from such models, therefore, the principle of their maintenance is similar.
In cars with diesel engine options, they didn’t go crazy and left the same fuel filter installation scheme.
Replacing the fuel filter on a petrol Megane 2
- Files
- Engine
- Engine capacity: 1.4, 1.6, 2.0 (l)
- Car model: Megane 2, Scenic
- Description of removing and replacing the fuel filter
- Where is the fuel filter installed?
Fuel filter code for Megane - 7700 845 961
Analogues: MAHLE (Knecht) KL83, Mann WK512
You can find out the cost of Renault spare parts for maintenance from our partners (existence, emex, autodoc, etc.), who provide discounts using the Renault-Drive card
. The fuel filter was installed separately on the Renault Megane of the first phase, i.e. year of manufacture of the vehicle before June 30, 2006.
The fuel filter in the second phase is located only in the tank and can be replaced together with the pump (if desired, a separate mesh).
On cars 2006 and even 2007, there is a fuel filter outside the tank - to determine its presence, you need to look under the car.
This report uses a KL72 fuel filter, its diameter is slightly smaller than the original, so I had to wrap a little electrical tape to fix it tightly in the mount. Try to buy the original or a suitable analogue (see codes above)
To make it easier to replace the filter, it is better to use a pit or lift.
To remove the filter, you need to press the square green clips (two on each side)
Pay attention to how the old filter is installed (direction of the arrows)
Remove the old filter from the mount, insert a new one, do not forget to take into account the direction of the arrows on the filter
Roughly speaking, gasoline “moves” through the filter from the front of the car to the rear.
We put on the fuel hose clamps until they click
Wiping down the work area
material: Nike-89 Drive2.ru
If you have anything to add to the article, or would like to share your experience on this topic, please leave a comment
If you are the author of a report on repairs, modifications of a Renault car, or recommend material for the Renault-Drive Knowledge Base, please let us know
Location
It’s worth noting right away that in Renault Logan 1.6 and 1.4 the replacement is carried out in a not entirely identical manner. The difference between these machines is only in the location of the filter element. One more nuance. The fact is that cars with a power unit capacity of 1.4 liters are still produced to this day. As for the Renault Logan with a 1.6 engine, this power unit was no longer used back in 2006.
So where is the required element? If we talk about cars that went on sale after 2006, then you need to look for it in the fuel tank. It is noteworthy that it is installed together with a gasoline pump.
If we talk about earlier models, everything is a little simpler here. The filter is located in the place where the tubes through which the fuel moves come out of the tank.
Subtleties of filter replacement for second generation models
The barrier for the second phase (for models 2007, 2008) Renault Megane is located in the tank and has a different installation procedure. It is replaced as an assembly with the pump, or you can replace only the mesh, which is the barrier on the 2007, 2008 models.
- Using long-nose pliers and a chisel, remove the latches from the fuel pipes.
- Then we take out the fuel pump itself. We remember the location of the minus and plus and remove the terminals from the fuel pump motor.
- We dismantle the bottom cover, and then the mesh barrier.
- Rubber rings from the previous pump are put on the new one, after which it is installed in the housing and the fixing bolt is tightened.
- A new tube prepared in advance is pulled onto each fitting up to the second mark.
- We install the mesh barrier and fix the terminals in accordance with the poles.
- Finally, we screw the union nut, put the rubber ring of the cover on the fuel pump, fittings and connector.
- In the video below you can follow all the features of this process for the 2007 and 2008 models.
A correctly executed algorithm of actions will prevent interruptions in the fuel supply and problems in engine operation.
Where to order repairs?
Do you want to protect yourself from unpleasant situations and order fast and high-quality service for your car in Moscow? offers a full range of Renault car repair services at an affordable cost. Our specialists have many years of experience and appropriate training, which allows us to guarantee high quality service. In our work we use only advanced equipment, high-quality tools and original spare parts. The cost of services is determined depending on the complexity of the work and the exact nature of the malfunction.
Some features of the pump replacement work
When disassembling the Renault Megane 2 fuel pump, it is necessary to mark the lower cup so that during reassembly you can install it in the same position and correctly position the float after assembly. To dismantle the lower cup, you just need to lightly hit its rim with a hammer, after which it will come out of the lock. Do not strike the cup where the fuel level sensor is mounted.
After removing the lower cup, the fuel pump mesh is cleaned. It should be visible, if the mesh is clogged, this may be one of the reasons for the deterioration of the fuel pump.
When repairing a fuel pump, you need to check the operation of its electric motor. To do this, connect the positive terminal of the battery instead of the turquoise wire, and the negative terminal instead of the black wire. If the engine starts, it is fine. Such a test is necessary if, after turning on the ignition, the pump does not pump fuel with a characteristic sound.
The fuel pump and pump of the Renault Megane 2 are at risk after 100 thousand km, so you need to monitor their condition. These components ensure fuel supply and normal engine operation. If there are doubts about the normal operation of these systems, the problem must be solved immediately, otherwise this will lead to major problems and high costs for car repairs.
Seal
Signs of a fuel pump malfunction
Before it breaks down, a worn-out fuel pump exhibits signs that indicate it will soon need repair or replacement:
- Difficulty starting the engine. This requires more than one attempt with a long cranking of the starter. This could be a problem with the battery or the starter itself, which cannot crank the engine. But, if the problem does not go away when starting on a hot engine, the cause is the fuel pump.
- One of the earliest signs of problems is a spontaneous change in the sound of the engine, and then its restoration for no apparent reason. At the same time, the engine itself operates stably, does not fluctuate, and has no extraneous noise.
- Reduced power. When you press the gas pedal, the car accelerates more slowly and responds with some delay. This is especially noticeable when overtaking or driving downhill. This sign is not so clear, since the reason for this behavior of the car may be bad gasoline or problems with the ignition system, for example, broken high-voltage wires.
- After turning the key in the ignition, you should hear the sound of a pump pumping fuel into the system for a few seconds. If it is not there, this clearly indicates a breakdown of the pump itself or the electrical circuit supplying it.
Replacing a gasoline filter on Renault Megane 2 video
Fuel filter code for Megane - The fuel filter was separately installed on the Renault Megane of the first phase, that is, the year of manufacture of the car before June 30 of the year.
The fuel filter in the second phase is located only in the tank and can be replaced together with the pump, if desired, the mesh separately. On cars, there is even a fuel filter outside the tank - to determine its presence, you need to look under the car.
This report uses a KL72 fuel filter, its diameter is slightly smaller than the original, so I had to wrap a little electrical tape to fix it tightly in the mount. Try to buy the original or a suitable analogue. To make it easier to replace the filter, it is better to use a pit or a lift. To remove the filter, you need to press the square green clips, two on each side.
Pay attention to how the old filter is installed in the direction of the arrows. Remove the old filter from the mount, insert a new one, do not forget to take into account the direction of the arrows on the filter
Roughly speaking, gasoline “moves” through the filter from the front of the car to the rear. If you have anything to add to the article, or would like to share your experience on this topic, please leave a comment.
Replacing the fuel filter on a petrol Megane 2
Registration Remember. Categories: DIY maintenance, engine, gearbox. Tags: megane gasoline filter.
We put the fuel hose clamps on until they click. We wipe the work area material: Nike Drive2. You just need to tap them with something, for example the handle of a screwdriver, the dust falls out and they press very easily.
Where is the Megane (diesel) fuel filter located and when to change it?
Don't forget about the discount with the Renault-Drive discount card. Alexey September 7 at 0 Add a comment RSS feed of comments.
Renault Driver September 5 at 0. Find out from any of our partners.
Alexey September 7 at 0. Please tell me the article numbers of the fuel filter clamps, which are very good with these green clips. I don't have it in this place.
Where is the fuel filter located in Renault Megane Classic
Buy fuel filter for RENAULT CLIO III (BR0/1, CR0/1)
Renault Megan is the successor to Renault R. On the Russian market since the end of 2010. These cars are still in use on our roads. In the maintenance manual for Renault Megane with the E7J engine, the air filter cover is designated as number 8.
The arrows indicate the mounting bolts and latches. We remove the filter, clean the internal cavity of the filter housing, install the filter, and fasten the parts in the reverse order. Analogs to the original:. In the maintenance manual, the air filter cover is numbered 8.
The green arrow points to the clamp securing the air intake pipe. We unscrew the screws securing the cover, disconnect the clamp, tilt the cover, remove and change the filter. The updated Megan 2, the second generation, entered the Russian market this year. Here is the original filter for this car: Unscrew the two screws securing the filter cassette cover. It is convenient to use a special screwdriver with a flexible shaft.
Then we take out the cassette with the filter and use a vacuum cleaner to clean the internal cavity of the filter housing. These filters are also used for Megan 3 - the third generation. They can be located, like the Megan 1.6 16V with the K4M engine. Fastened with two screws. Located behind the engine. We remove the clamp on the air intake pipe, move it to the side and pull out the resonator box. We looked at replacing Renault Megane air filters of all generations. The filter is serviced every thousand km. Buy reusable filters.
Opel 4. Nissan 5. Honda 3. KIA 2.
Tube fuel cable scenic ii
UAZ 1. VAZ 3. Air Chevrolet 4.
Toyota 5. VAZ 7. Renault 9.
Fuel filter for RENAULT CLIO III (BR0/1, CR0/1)
Peugeot 2. Ford 6. Skoda 3. Citroen 1. Mazda 4. Volkswagen 1. Audi 1. Opel 1. Oil Toyota 3. Renault 1.
Replacing the fuel filter — Renault Megane, l., year on DRIVE2
Unstable engine operation; Severe decrease in engine power; no other problems with the unit; Increased fuel consumption. In a car built on an injection system, it is the coarse filter that primarily suffers from low fuel quality.
Usually the problem does not appear immediately, but gradually. At first, the symptoms of a malfunction may be almost unnoticeable, but over time, the fuel filter on Renault Megane 1 only increases. The main cause of failure is low-quality fuel. Often its use leads not only to blockages, but sometimes to corrosion of the cleaning element. First, the flow of the mixture through the hoses becomes difficult, and then the injectors and other engine elements lose their functionality.
Replacement for Renault Megane 2 Renault Megane 2 fuel filter is part of the car’s fuel system; the fuel filter is mounted separately on cars produced up to a year; to determine the location of the part, you need to look under the car.
Rules for choosing consumables
It is not recommended to restore the old cabin filter, as this part cannot be repaired. Suitable for Renault Megane 2 car:
- Single layer systems. Completely gets rid of poplar fluff, dust, soot, pollen, and insects that have gotten inside the car.
- Double layer filter. Elimination of unpleasant odors and toxic gases from the interior is ensured.
- Three-layer device. Can simultaneously perform the functions of single- and double-layer cabin filters.
- Combined systems. This is a compact and affordable unit that effectively removes a wide variety of contaminants from the interior.
A variety of filter systems can be installed in Renault Megane 2. Their choice depends on the degree of pollution of the car and the financial capabilities of the car owner. The most popular analogues of the Renault Megane 2 filter include:
- The installation is made in Germany and has a high build quality. Thanks to the presence of a high-quality plastic frame, a perfect fit of the equipment to the wall is ensured. Although the length of the filtration system is shorter than the original, it does not allow untreated air to pass through.
- Cedar. This model combines low cost and excellent technical characteristics. When using the device, high-quality filtration of air in the car interior is ensured even when the vehicle is moving at a speed of more than 100 kilometers per hour. The manufacturer produces a carbon analogue of the filter, which not only cleans the air, but also removes unpleasant odors. The device has a reliable housing that is resistant to mechanical damage.
- MANN FILTER. The German manufacturer produces several types of filters. Nanofibers are used to make the filter element, providing high-quality purification of polluted air. Model 1829 consists of a regular, anthracite and antibacterial layer. Thanks to the three-layer system, high-quality air purification and neutralization of foreign odors are ensured. By modifying the plastic in the bending areas, convenient installation of the device is ensured.
Renault Megane 2 is allowed to install filters from various manufacturers.
Their choice is made based on the preferences and financial capabilities of the car owner.
Replacing the fuel filter Renault Megane 2
Every driver has at least once encountered the need to change the fuel filter.
In this article we will tell you how to do it yourself. Selecting the right element For the diesel version of Renault Megane 3, the market offers a wide selection of fuel filter manufacturers. There is an opinion that for reliable operation of your car you should install only original parts on it.
Renault Megane 3 fuel filter replacement
For gasoline engines, the situation is not so simple, because the cleaning part is structurally integral with the fuel filter for Renault Megane 3. Often its use leads not only to blockages, but sometimes to corrosion of the cleaning element. First, the flow of the mixture through the hoses becomes difficult, and then the injectors and other engine elements lose their functionality. Replacement for Renault Megane 2 Renault Megane 2 fuel filter is part of the car’s fuel system; the fuel filter is mounted separately on cars produced up to a year; to determine the location of the part, you need to look under the car.
The original part costs 12 thousand rubles, analogues are cheaper. In this case, a KL filter was used. It is smaller in size than the original, so I had to wrap electrical tape on top so that the parts fit tightly and are fixed. When replacing a fuel filter for Renault Megan 3, a Renault Megan 2 filter, it is recommended to buy the original or a close analogue. Repairs are easiest to do in a pit or on a lift.
The Megan 2 fuel filter is secured with two green clips, 2 on each side.
Replacing the fuel filter in Megan 3 petrol and diesel
It is important to pay attention to how the old part is installed, remember the direction of the arrows. Using a 10 mm wrench, unscrew the retaining bolt holding the filter and housing assembly. Then, you need to disconnect the two fuel pipes, this can be conveniently done from above after removing the right headlight
Replacing the fuel filter in a Renault Megan 3 car, the procedure for a fuel filter for Renault Megan 3 is complex and the car owner can replace it with his own hands. Disconnect the H2O presence sensor, then replace the 4 round gaskets
Then, you need to disconnect the two fuel pipes, this can be conveniently done from above after removing the right headlight. Replacing the fuel filter in a Renault Megan 3 car, the procedure for a fuel filter for Renault Megan 3 is complex and the car owner can replace it with his own hands. Disconnect the H2O presence sensor, then replace the 4 round gaskets.
Wheels for Renault Megane 3 Megane: Replacing the air filter in Renault Sandero Stepway. Connect the sensor to the new element, having previously cleared it of dust and other objects. Renault Megane III year 1. Scenic 3 dci 1.5 replacement of the fuel filter Megane 3 This filter replacement is for a car after the city And with an electric boost pump in the tank.
Fuel filter RENAULT MEGANE III
Even a novice driver can replace the fuel filter on a Renault Megane. In other modifications 1.5.
Reinstall the filter by connecting the hoses and water sensor connector, and then tighten the retaining bolt. The replacement procedure will be considered complete only after pumping diesel fuel, which is done using a bulb under the hood.
Reinstall the fender liner, as well as the headlight, secure the front wheel and remove the car from the jack, not forgetting to tighten the bolts. Replacing the fuel filter on a Renault Megan diesel engine 1. On Renault Megan 3, these procedures are simple, and any novice motorist can easily cope with this task.
Gasoline brother Compared to the previous Renault Megane 3 gasoline model, it is equipped with a submersible filter, the service life of which is designed for thousands of kilometers.
Description of the design of the Renault Logan engine management system
Diagram of the Renault Logan electronic engine management system: 1 - battery; 2 - ignition switch; 3 - main relay; 4 - switching unit; 5 - air conditioning relay; 6 - cooling system fan low speed relay; 7 - ventilation, heating control unit and air conditioning; 8 - fan;9 - instrument cluster;10 - high speed cooling fan relay;11 - coolant pressure sensor;12 - power steering pressure sensor;13 - diagnostic connector (diagnostic block);14 - electronic engine control unit;15 - fuel pump and ignition coil power relay;
16 — fuel module; 17 — adsorber for gasoline vapor recovery system; 18 — vehicle speed sensor; 19 — knock sensor; 20 — absolute air pressure sensor; 21 — idle air control; 22 — intake air temperature sensor; 23 — throttle position sensor dampers; 24 — injector; 25 — crankshaft position sensor;
Elements of the electronic engine control system (ECM):1 - ignition coil;2* - diagnostic connector;3 - injector;4* - knock sensor;5 - idle speed control;6 - throttle position sensor;7 - intake air temperature sensor ;8 — absolute air pressure sensor;9* — vehicle speed sensor;
The electronic engine control unit (ECU) processes information from control system sensors, receives signals from the air conditioning switch and power steering pressure sensor, and also controls actuators such as the fuel pump, injectors, ignition coil, idle speed control, canister purge solenoid valve, cooling system fan, electromagnetic clutch of the air conditioning compressor.
Replacing fuel and air filters Duster
Every car uses a special filtration system. For its proper operation, it is necessary to change the air and fuel valves in a timely manner. However, in each individual case, it is necessary to take into account the engine type, vehicle mileage and other important details. Let's briefly consider the specifics of replacing filters on Renault Duster.
When replacement is necessary
The Renault Duster manufacturer recommends using a particular filter in accordance with the regular maintenance schedule:
- Replacing the air element in a 1.5 diesel engine must be done every 10 thousand km, while the mileage of 1.6 and 2.0 gasoline engines can be every 15 thousand km.
- The fuel filtration element is replaced for the first time after 10 thousand km. and subsequently - every 15 thousand km. (the rule applies equally to petrol and diesel versions).
Replacing the air filter
Replacing the air filter
Changing the oil and oil filter
Replacing the cabin filter
Replacing the air filter
It is important to know! Replacing the Renault Duster air filter is a simple but extremely necessary procedure that will significantly extend the life of your car's engine. Never neglect this important part of maintenance.
To make the replacement, you will need a 10 mm wrench, Torx T25, a screwdriver and a new filter according to Renault standards.
Non-original spare parts cost an order of magnitude lower than prototypes, especially if you take into account the prices of official dealers. Low prices and good quality of non-original goods attract many buyers
On a diesel engine:
- Disconnect and remove the inlet pipe (it is secured with a clamp).
- Disconnect the battery terminals.
- Remove the screws holding the sensor (located at the top of the air filter box on the right side).
- Then you need to deactivate the electrical block (located at the top left).
- Here, disconnect the pipe - to do this, you need to loosen the clamp that holds it together.
- Now there is nothing holding the case in place and you can remove it and remove the mounting screws.
- After replacing the filter with a new one, set the indicator regulator to the initial position.
- Reinstall the box and follow these steps in reverse order.
On a gasoline engine:
- Disconnect the inlet pipe clamp and remove it. Disconnect the pipe.
- Open the rubber part of the resonator and the plastic part of the housing.
- Disconnect the vacuum tube by loosening the clamp that holds it.
- Using a T25 Torx wrench, remove the screws.
- Remove the case and replace the filter.
- Reassemble and connect in reverse order.
Replacing the fuel filter
Replacing the Renault Duster fuel filter, like replacing the air filter, is a very important maintenance procedure. As in the first case, you will need simple tools and basic knowledge of the Renault Duster engine fuel system. To replace, you will need a new fuel filter.
In a car with a 2.0 liter engine, in addition to the basic cleaner, another one is used, but it is located in the engine compartment.
To make a replacement, follow these steps:
- Release the pressure in the fuel system. To do this, disconnect the power terminal from the pump and start the engine - wait until it stops running. Crank the starter for a while.
- Remove the filter and drain the remaining fuel.
- Install a new filter. Be careful not to confuse the direction of circulation. There are special marks on the case that will tell you how to connect the element correctly.
- Reassemble everything in reverse order.
It should be understood that any car repair, even such as replacing a filter, will cause certain difficulties for an inexperienced user. Therefore, if you do not have the necessary knowledge and skills, the best solution would be to contact our specialized EURO-Globus service center.
How to replace the fuel filter yourself
As already mentioned, the design of the Megane 2 in terms of installation of the filter component depends on the year of manufacture of the car. Let's consider the first installation option in the early models of the second series of Frenchmen.
Before starting to replace the filter, it is better to apply double-sided tape to the new product - wrap it around the body in the area where the clamp is attached.
- Now you need to install the car on the inspection hole or lift it on a jack, observing safety precautions.
- Find an old cleaner and green fasteners on both sides. Here we must not forget about the presence of arrows indicating in which direction the fuel mixture is moving. The position of the new filter depends on this.
- Accumulated road dust and dirt may cause the latches to fail to budge. You need to clean them (wash them or tap them so that the dirt falls off).
- Remove the old filter and put a new one in its place.
On cars produced from the factory assembly line after 2007, the cleaner is installed in the fuel pump and can be removed separately or together with the pump.
On cars with diesel power units, the principle of replacing the fuel pump is no different and does not depend on the Megane generation. The work can be done independently and can be done by any beginner.
The right side of the car is jacked up and the wheel is removed.
Next, they begin to remove the protection by unscrewing the fastening screws.
If you bend it, you gain access to the cleaning module. It is located in the casing.
Now we begin to remove the front headlight. It is not necessary to disconnect the wires.
Moving it to the side, the fuel filter is removed through the hole in the car body.
Dismantle the fuel mixture heater and install it on a new filter, not forgetting about the sealing material for the new product.
The assembly order is reversed.
The procedure for replacing the fuel purification module is quite simple and will only take about 20 minutes. It does not require enormous experience and knowledge, so there is no need to delay the installation of a new product.
After all, the performance of a car engine depends on the quality of the fuel.
On auto sites you can see how to step-by-step carry out operations to replace this important component of the vehicle fuel system
Replacing a gasoline filter on Renault Megane 2 video
Fuel filter code for Megane - The fuel filter was separately installed on the Renault Megane of the first phase, that is, the year of manufacture of the car before June 30 of the year.
The fuel filter in the second phase is located only in the tank and can be replaced together with the pump, if desired, the mesh separately. On cars, there is even a fuel filter outside the tank - to determine its presence, you need to look under the car.
This report uses a KL72 fuel filter, its diameter is slightly smaller than the original, so I had to wrap a little electrical tape to fix it tightly in the mount. Try to buy the original or a suitable analogue. To make it easier to replace the filter, it is better to use a pit or a lift. To remove the filter, you need to press the square green clips, two on each side.
Pay attention to how the old filter is installed in the direction of the arrows. Remove the old filter from the mount, insert a new one, do not forget to take into account the direction of the arrows on the filter
Roughly speaking, gasoline “moves” through the filter from the front of the car to the rear. If you have anything to add to the article, or would like to share your experience on this topic, please leave a comment.
Replacing the fuel filter on a petrol Megane 2
Registration Remember. Categories: DIY maintenance, engine, gearbox. Tags: megane gasoline filter.
We put the fuel hose clamps on until they click. We wipe the work area material: Nike Drive2. You just need to tap them with something, for example the handle of a screwdriver, the dust falls out and they press very easily.
Where is the Megane (diesel) fuel filter located and when to change it?
Don't forget about the discount with the Renault-Drive discount card. Alexey September 7 at 0 Add a comment RSS feed of comments.
Renault Driver September 5 at 0. Find out from any of our partners.
Alexey September 7 at 0. Please tell me the article numbers of the fuel filter clamps, which are very good with these green clips. I don't have it in this place.
Fuel filter Renault Megane 2 and 3
- 64 13 48k
- 0 0 75k
The fuel filter for Renault Megane 2 and 3 generations differs both in engine type and, in part, in its volume. Also, depending on the year of manufacture of the car, the location of the main filter element differs.
Fuel filter for Megan 2
On Renault Megane 2nd generation with all gasoline engines, until 2007, a fine fuel filter was installed separately. It is located under the bottom of the car, near the rear wheel, under the gas tank, on the driver's side. This arrangement is quite convenient in terms of replacement, especially if there is an inspection hole. For these modifications of the car, a fuel filter is installed from the manufacturer under the Renault article number 7700845961, the price is 350 rubles. The original manufacturer is Mecafilter.
Fuel filter dimensions for Renault Megane 2, petrol engines | ||
Height, mm | Inlet/outlet diameter, mm | Case diameter, mm |
143 | 8 / 8 | 55 |
When replacing a fuel filter, drivers, as a rule, more often choose one of the analogues, since they are more common, and the original is more difficult to find for sale in a regular store. And the price for them is usually a little lower. The table below shows the most popular replacement models.
Manufacturer | vendor code | price, rub. |
Mahle Original/Knecht | KL416/1 | 600 |
SCT | ST 342 | 150 |
Bosch | 0450902161 | 300 |
However, for gasoline Megana 2s released after 2007, fuel filters are already installed inside the fuel module along with a pump, sensors, a level float, and a mesh filter, which is located inside the tank. It does not change separately and is designed for the entire service life of the pump. To get to this module, you just need to lift the rear seat, after which access to the cover opens, under which the above-mentioned spare part is located. The module article number is Renault 8200683188, the price is 14,000 rubles. If the pump itself fails, drivers often replace it with Bosch 0986580804, price - 3,500 rubles. You can also change the filter mesh separately. There is no original article for it, but they usually put in a substitute from Francecar - FCR210141, price - 120 rubles.
Some Megane II car owners change the design of the module itself, making an insert into it, and move the fine fuel filter outside.
Instead of the stock fuel module assembly, you can also install one of the cheaper analogues:
Manufacturer | vendor code | price, rub. |
Magneti marelli | 313011313049 | 3900 |
Krauf | KR0440M | 3400 |
Lex | HT-2546 | 3000 |
Fuel filter for diesel Renault Megane 2
On diesel Megane II, fuel filters differ depending on the size and modification of the engine, so it will be more difficult to choose. Power units with volumes of 1.5 and 2.0 are equipped with fuel filters in the shape of a solid plastic or metal cylinder with several outlet pipes. On a 1.9 engine, only the cartridge insert with the filter element is changed.
It is also worth knowing that this car with diesel engines may have installed fuel systems from Delphi or Siemens. Delphi is more demanding, and it is recommended to install only original Delphi filters on it.
Fuel filter dimensions for Renault Megane 2, petrol engines | ||||
vendor code | Engines | Case diameter, mm | Height, mm | Diameter of pipes, mm |
7701067123 (with connected water sensor) | 1.5 dCi, 2.0 dCi; K9K – (724, 732, 734+M9R) | 93 | 121 | 10 |
8200697875 (without water sensor connection) | 1.5 dCi, 2.0 dCi; K9K – (724, 732, 734+M9R) | |||
8200186217 | 1.5 dCi, 2.0 dCi; K9K – (722, 728, 729+M9R) | 93 | 187 | 8 |
7701061577 | 1.5 dCi; K9K – (722, 728, 729) | 74 | 185 | 8 |
7701044913 (filter insert) | 1.9 dCi; F9Q | 70 | 92 | — |
The fuel filter is located on all diesel Megane 2 near the engine, behind the front right wheel (passenger side). When replacing, you need to jack up the car and remove the wheel. For convenience, you can also remove the headlight and fender liner. Below are the most popular analogues for each of the filters.
Manufacturer | vendor code | price, rub. |
1.5 dCi, 2.0 dCi; K9K – (724, 732, 734+M9R), with water sensor | ||
Bosch | F026402061 | 2500 |
MANN | WK 919/1 | 2900 |
1.5 dCi, 2.0 dCi; K9K – (724, 732, 734+M9R), without water sensor | ||
Bosch | F026402016 | 1600 |
Mahle/Knecht | KLH44/22 | 1700 |
1.5 dCi, 2.0 dCi; K9K – (722, 728, 729+M9R) | ||
Delphi | HDF584 | 3000 |
Mahle/Knecht | KL432 | 1100 |
1.5 dCi; K9K – (722, 728, 729) | ||
Delphi | HDF917 | 2300 |
Bosch | F026402077 | 2000 |
1.9 dCi; F9Q | ||
MANN | P 733/1 X | 550 |
Filtron | PM 816/1 | 220 |
Price, originals and analogues, article number
In order for the car engine to perform its functions efficiently, Renault advises purchasing only original spare parts. But, most car owners, if replacement is necessary, still buy less expensive non-original parts and components from other manufacturers. This is not surprising, because the cost of the spare part plays an important role for the driver of the vehicle.
The table shows the most common fuel purifiers for Megan 2 and 3 brands
Fuel filter type | Manufacturer | vendor code | price, rub. |
Gasoline | RENAULT (original) ALCO FILTER BOSCH | 7701068107 SP-2061 0 450 905 287 | 920 340 800 |
Diesel | RENAULT (original) FILTRON VAICO | 164005190R PP9806 V46-0598 | 3200 1400 1500 |