Starline service button: where is it located and how to find it yourself?

03/01/2022 2,353 Alarms

Author: Victor

Knowing where the Starline service button is located may be necessary, for example, to switch the alarm system to Valet mode in order to carry out vehicle repairs at a service station. When searching for a key, you need to take into account that it has several types of configuration and can be made as a separate unit or built into other elements of the StarLine car alarm. In the first case, the Valet button is a separate device, which is secured with glue or double-sided tape in a secret place.

[Hide]

Where is the service button for the Starline A93 alarm?

The Starline service button is located

inside the car, in a place that is easy to access for the driver, but invisible to outsiders.
... Where to find button
.

How to turn on the car alarm after it has been turned off?

Instructions for the repair and operation of special cargo vehicles.don south auto serviceconnection of starline alarm system to webastoconnection of starline m20 and starline m30 to webasto webasto

Disabling service mode for almost all devices is the same. To do this you will need:

1. Insert the lock, start and stop the engine.
2. After about 10 seconds, press the Valet button or turn the switch to the OFF position. If you are using a remote control, you need to open the lock and press the speaker button.
3. Disabling the service mode will be accompanied by a double sound signal from the indicator on the control panel.

There is nothing scary about blocking an alarm. The main thing is not to panic. As a last resort, if you can’t figure it out, you can look through the Internet and find instructions for a specific model. If this does not help, then go to the service.

How to turn off the alarm in more detail in the video:

I had an unpleasant situation with the remote control; he didn’t want to turn off the alarm with the key fob because he picked up a radio interference problem. I parked my car that day and when I returned from work to the parking lot in the evening I could not turn off the alarm from a great distance, and this happened a total of 3 times. When I was disappointed for the last time and came closer to the driver’s side, I pressed the remote control and yet somehow, miraculously, my car finally unlocked and turned off the alarm.

In the cold weather, I left the driveway in the morning and walked up to the car, pressed the remote control hard and wanted to quickly leave for work, but the car didn’t open the door, so I called my friend who pulls in cars. Having arrived at the scene, he explained that the problem had arisen with the door mechanisms and that the remote control was giving the wrong notification and the remote control was faulty. He confirmed my hypothesis that all this happened due to freezing of the mechanisms. After some time, I opened the car with my magic hands, rechecked everything so that this would not happen again and I got to work normally, in the evening of the same day the car no longer malfunctioned using the remote control.

When such a nasty problem appeared, I promptly did the following. The remote control that I turned on did not react at all to turning it off, much less to turning it on. I thought of doing this: having disconnected the siren from the bell terminal from the battery, the second step was to replace the old battery with a new one. The battery began to function as before in the same condition. Since I understood this issue perfectly, I refused the help of my dear brother, who called me when the problem arose.

Most modern cars are equipped with a car security system that allows you to protect your vehicle. Even criminals prefer not to touch a vehicle with an alarm; ordinary hooligans planning to damage property rather than steal it will also bypass a protected vehicle.

The range of alarms from various manufacturers is huge. At the same time, not all models are reliable and durable, and, as a result, the car enthusiast faces some problems. A car owner who has installed a device on his car for protection often looks for the answer to the question of how to turn off the car alarm completely.

Incorrect operation of the security system can be associated with various problems. Most often, failures occur precisely because of poor-quality equipment. Extremely low or high air temperatures cause problems. Incorrect operation is also associated with malfunctions of the internal components of the device.

A problem may be indicated by overly sensitive operation or problems occurring when turning the equipment on or off. Motorists often encounter false alarms. All of these problems indicate that your vehicle's safety equipment is in urgent need of repair.

Problems with a faulty key fob can be caused by the following reasons:

• Too much radio interference that interferes with the normal operation of the alarm panel;
• Problems with the car battery;
• Low battery.

If the breakdown is due to a dead battery in the key fob, try taking it out, shaking it slightly and putting it back in place. Manipulations of this kind will help to revive the device for a few minutes. Don't forget to replace the dead battery.

Very often, problems with the signaling arise due to a dead battery in the key fob.

What is the StarLine service button?

StarLine service button

- a device for controlling security alarm functions, which is used in the following cases: Switching to Valet mode allows service employees to work with the car, but at the same time prevents their attempts to make changes to the car alarm settings.

Interesting materials:

How to set up archiving in Outlook 2013? How to set up ashdimiai on TV? How to set up login auditing? How to set up Outlook on iPhone? How to set up auto dialer on Android? How to set up Airwick automatic air freshener? How to set up an automatic air freshener? How to set up an automatic reply in direct message? How to set up an automatic reply on WhatsApp? How to set up automatic translation in Google Chrome?

Description of functions

What does the override button look like and where is it located on a tomahawk alarm
? Motorists choose the Starline B9 because of its ability to provide a sufficient level of protection for several areas of the vehicle at once:

• electrical circuits of internal combustion engines;
• hood, luggage compartment and doors;
• hand brake lever;
• car interior.

The security device relay is responsible for protecting the circuits, but in addition, the ignition circuit is additionally protected - the system reacts to the appearance of voltage in the ignition switch. As for the doors, hood and trunk, their protection is ensured by limit switches, which can be purchased additionally. Thanks to the operation of the standard switch when the handbrake is released, it is also protected. And the interior is controlled by a customizable shock sensor.

1. M21;
2. M31.

The first of them provides the ability to control the system from a smartphone, thanks to which distance ceases to be an obstacle to setting up security functions. As for the second block, in addition to mobile control of the device, it makes it possible to control the position of the machine based on data from GPS and GLONASS satellites, as well as mobile communication towers.

In general, the functions of Starline B9 are traditionally divided into anti-theft and service. The first include:

• activation of the alarm mode based on sensor signals;
• notifying the car owner using a signal from both sirens and on the key fob;
• immobilizer mode in case of need to immobilize the vehicle;
• two-stage shutdown that can be programmed;
• deactivation of the device based on a special programmed secret code;
• blocking the operation of motor circuits;
• storing trigger conditions in memory;
• silent activation of security mode
• programmable silent alarm operation - alarm signals are given by headlights and lamps on the key fob.

With some additional features, the vehicle owner can achieve enhanced protection. Namely, using:

• floating control code, which is protected from reading by code grabbers;
• returning to the last settings before the power outage immediately after power supply is restored;
• limited number of consecutive operations based on information from sensors;
• disabling alarms of any type without deactivating the anti-theft system itself.

As for service functions, the main ones include:

• the ability to maintain the security mode when the engine is turned on;
• control the system without a remote control;
• automatic resumption of security mode after an accidental temporary shutdown;
• control from a long distance not only by sensors, but also by door locks;
• the ability to lock and unlock doors using the ignition switch;
• the ability to install two-stage door opening;
• the presence of additional channels that make it possible to control auxiliary equipment;
• vehicle detection function in a parking lot;
• protection of buttons on remote controls from accidental pressing;
• the ability to configure both a turbo timer and auto engine start;
• indication of the reasons for the activation of the alarm signal by pictograms;
• the presence of special sound signals for various reasons for triggering;
• indication of faults during arming.

Among the functions of remote control of internal combustion engines, it is worth highlighting:

• starting and stopping it from the control panel;
• extending the operating mode remotely;
• the ability to configure start by temperature or time, as well as by alarm;
• control over the operation of the motor based on signals from the speed sensor, also based on information about the operation of the internal electrical network;
• disabling the starter in automatic mode;
• indication of the motor operating status on the LCD display of the key fob using pictograms.

Thanks to such diverse functionality at a reasonable price, the Starline B9 alarm system has not yet lost the appreciation of consumers.

Setting up the Starline car alarm key fob

1. The ignition is turned on, the protective mode is turned off. This is the first step when setting up the StarLine key fob.
2. The protective mode is activated by only 1 button, which is pressed 7 times successively and quickly.
3. Successful communication between the components is indicated by a seven-time beep sound after the ignition is turned on.
4. Buttons 2 and 3 are used simultaneously. They are held until the system receives a 1x signal.
5. The ignition turns off. Blinking the turning lights five times will confirm the correctness of the actions. The alarm configuration for this function is completed.

Enabling auto alarm

Only a master can correctly configure Starline autostart. It uses setting a special PIN code to implement the function. The device memory saves all settings specified by the manufacturer. If additional autorun installation is necessary, the alarm setting is reset to its original state.

In a separate algorithm, actions are performed to prepare the system for launch:

• Maintaining a neutral position for the lever that controls the manual transmission.
• Removing the key from the lock after the engine has started running. The engine is left running.
• Starting the brake operation in manual mode.
• Close all doors along with the hood and trunk.

A convenient option is to enable autostart from the key fob, depending on the temperature and time indicator.

Setting the time

The issue is resolved by a not-so-complicated sequence of actions:

1. Wait for two simultaneous sound signals to appear after pressing the third button. Then other signals will follow, there are also two of them. This means that you have finished entering the watch settings. At the next stage, two indicator lights turn on on the screen.
2. The minutes are adjusted by pressing button 3 once. Buttons 1 and 2 are pressed respectively to increase or decrease the value.
3. Activating the alarm function involves pressing button 3 next time. The hour value is adjusted by buttons 1 and 2.
4. The minutes are set by repeatedly using button 3.
5. The alarm is activated if button 3 is used again.
6. In the future, the same button is responsible for the timer. Buttons 2 and 3 increase or decrease the available values.
7. If nothing is pressed for 5 seconds, the alarm settings are simply closed.

Adjusting the volume of sound alerts

In this case, you will need a tool called VALET. First, turn off the ignition, press the button 5 times, and turn on the engine again. Then button 2 is pressed, followed by the appearance of SO UN.

When setting up, start by holding down button 3 for a few seconds, then press the button on the left. The display will show the exact number corresponding to the current volume level. The desired levels are adjusted by continuing the adjustment with the 3rd button. Then you can start using the StarLine alarm system.

Adjusting the sensitivity of the shock sensor

And here you need button 3. It is enough to hold it for a few seconds, then release the button and press it again. The sensitivity of the sensors is adjusted by buttons 2 and 3. The latter is pressed if it is necessary to save the results of the settings.

How to reset the key fob settings?

Sometimes you need to forget previous settings in order to restore the device to its factory state. And there is nothing complicated here if you follow this order:

• Turn on the ignition with the key in the lock.
• VALET from the Starline alarm must be pressed 9 or 10 times. The instructions for each specific model specify the exact number of times.
• The ignition is turned on and several beeps are heard.
• Another use of the Valet button before the signals are heard in the form of sound.
• Next comes button 1. After pressing it, wait for a sound signal, then confirm the action with resetting the settings.
• When the work is completed, the ignition is turned on again, with the turn signals blinking 5 times. The alarm panel is being rebuilt.

Setting up additional features

Features such as opening and closing doors operate in automatic mode. Sometimes the number 10 is used to refuse the operation of a particular function if necessary. The general design and operating modes of the key fobs remain approximately the same. But there are still specific differences between the models. It is better to study the instructions in advance to obtain more accurate information. Then the Starline alarm will not cause problems.

Entering and exiting the main menu

To enter the main menu, press the service button five times with the ignition off. Then turn on the ignition. You will be taken to the main menu.

Short press keys 2 and 3 on the key fob to select the programming item you need:

• AF – service and security functions
• SF – launch settings
• CH 01-CH 09 – setting up additional channels (flexible) Starline A93
• SOUN – setting the siren volume

To exit programming, turn off the ignition.

You can find out where the service button is located from your installer.

It can be located under the panel and tied to some standard harness. Often it is hidden in the space next to the fuse box or directly glued to it.

In the latest versions of Starline A39, the service button is built into the antenna module.

Malfunctions and repairs

Most often, users encounter the following malfunctions of the Valet button in Starline alarms:

• Broken contact between the switch and the main unit of the system. The button is connected to the main unit via a special connector located at the end of a small diameter cable. A common problem is a loose connection, as a result of which, with a slight tension or movement of the wire, the contact breaks. Fixing the problem is easy - just insert the contact tightly into the socket.
• Button failure. The Valet service key rarely fails, because... It is rarely used by the owner of the car. This malfunction occurs as a result of mechanical damage - a kick or any object. Failure may be associated with the appearance of corrosion on the button resulting from exposure to high humidity. To fix the problem, you need to change the key.
• Broken wire. The cable to the Jack button must have an additional braid, because during vehicle operation it can withstand quite heavy loads. Therefore, damaged or broken wires are a common malfunction. You can easily fix it with your own hands; you just need to replace the cord with a new one.

You can fix these breakdowns yourself. If the malfunction is due to another reason, or the repair did not produce the desired effect, you should contact a service technician.

Locations

As a rule, the Starline A91 service button is always installed in the same place, namely under the dashboard. Getting to it is not so easy, but if you know exactly where it is located, then you will definitely do it. This button will come in very handy if you lose your key fob or it breaks down.

Using the service button, you can both activate and deactivate the alarm, which is very convenient if you lost your key fob the day before. Usually this lifesaver button is located near the driver’s seat - it is located directly under the fuse box cover, or rather, a little to the left and a little below the steering wheel.

It is advisable to ask the technicians immediately after installing the alarm where they have assigned the service button. This way you will know exactly where the button is. If you forgot to ask about its location in a car service center or this information simply flew out of your head, then I advise you to look for it yourself. It has a diameter of about 1.4 cm, the size is not large, so when you need it, it may take a certain amount of time to find it, which may cause dissatisfaction among neighbors. So, in order for the residents of your house to continue to greet you, I advise you to find the service button in advance. This button is attached with double-sided tape, so different craftsmen install it in different places.

Is the device useful for car alarms?

When connecting the antenna to a car alarm, a high speed of signal capture is ensured. That is why the security complex begins to work more clearly and correctly. Car alarms fall into the category of universal equipment that has a number of functions.

Absolutely all Starline car alarms are equipped with key fobs that allow you to control

equipment at a certain distance. The equipment protects the engine, doors, trunk, hood, body, ignition, interior space and parking brake of the vehicle. Thanks to the use of dialogue control code, starline equipment provides a high level of signal transmission protection. It also eliminates the possibility of intelligent electronic hacking.

Starline equipment has turbo timer and immobilizer functions, which significantly improves protective functions. Thanks to the possibility of self-diagnosis of the car alarm, it is possible to ensure its correct operation, as well as high quality signal capture by the antenna. When dismantling the equipment, not only the engine is blocked, but all settings are saved, which eliminates the need for additional synchronization of the equipment with the antenna after reinstallation.

Thanks to the universal functions of the starline device, it is possible to start the vehicle engine from a distance. Car door locks open in two stages using an encryption code. Thanks to the presence of a silent operation mode, the most convenient use of the security system is ensured. The car alarm is equipped with a special protection function, which eliminates the possibility of accidentally pressing the key fob buttons. This is a fairly important function, which is explained by the almost instantaneous pickup of signals by the Starline antenna. Thanks to the energy saving mode of the key fob, its long-term and uninterrupted operation is ensured.

The starline security device protects the car with the highest quality. Many car owners are dissatisfied with the poor quality and slow response of their car alarms. This is due to poor reception of signals by the security complex. In this case, you need to connect an antenna to the car alarm. It will significantly speed up the signal transmission process. Due to the simplicity of the antenna design, you can easily install it yourself. For this purpose, you just need to strictly follow the installation instructions.

Tired of paying fines? There is an exit!

• Absolutely legal (Article 12.2);
• Hides from photo and video recording;
• Suitable for all cars;
• Works through the cigarette lighter connector;
• Does not cause interference to radios and cell phones.

Find out details

How to disable Valet mode

Each instruction manual for a security alarm installed in a car contains a description of how to turn this service option on/off. So, if you wish, you can study this section and act accordingly.

But, as they say, everything happens in life and it may happen that either such a section is missing in the instructions, or, even worse, the instructions themselves are lost.

Then you should perform standard actions. Although each security system has individual characteristics, their main capabilities are usually common. Therefore, it is in principle possible to disable Valet, but it will not be as fast as we would like.

To exit this mode, do the following:

• sit in the passenger compartment and again perform the steps described above with the ignition. Moreover, you need to act quickly, otherwise everything will have to start all over again;
• determine the location of the Valet push-button switch (this should be known from the instructions, if not, then you must find out where it was installed);
• after 10 seconds have passed after the ignition has been turned off, you need to press this button for 2 seconds and then release it;
• Next, you should hear two or more short alarm beeps, the light emitting diode (LED) will turn on and off twice. Valet is disabled, car alarm is working.

Here's how to disable this option using remote control:

• First check the control panel, paying attention to the presence of the necessary buttons. If there are none, it means that they have a different designation in your security system, and therefore for help you need to contact the service center that installed the alarm on your car;
• then turn the car ignition on and off after getting into it. After this, press two buttons on the remote control at the same time and release them after 3 seconds. Next, several beeps will sound, the side lights will flash, and the car alarm LED will stop lighting.

If it happens that the alarm system does not respond to disabling the Valet mode from the remote control, then try removing the batteries from it and inserting them back after 2 minutes. Then you should check the connection between the key fob and the main unit. When you turn on the power, different signs should appear on the screen.

It is better to press the Valet key without anyone else. This action is completely justified. After all, you must agree that strangers should not know the location of the button that makes your car vulnerable.

By the way, the Valet service mode is maintained even when the power is turned off, so it can be used during vehicle maintenance. If the mode is turned on in the anti-theft system, the LED will glow constantly.

It is worth noting that switching to Valet mode does not involve disabling all running systems, but only the main part of them. For example, the emergency security measure “Panic” remains active. This function provides the ability to prevent car theft, provided that you always take the ignition key when leaving it. If you notice that someone is trying to steal your car, take the key fob and activate the “Panic” button and after a while you will see how all the security and locking systems will work. This will happen even when your security system is in Valet mode. By the way, in some alarm systems the “Panic” service corresponds to “Anti-Hi-Jack”, which has the same functions.

Everyone knows about Valet mode, including car thieves. But only vehicle owners are aware of the location of the button. Therefore, it is advisable to keep the location of its installation a secret, because you never know... Be vigilant and your car will be safe.