Starline autostart is the very function for which most car enthusiasts install this security and telematics complex. Regardless of the alarm model, it is quite simple and convenient.
But some configuration features must be taken into account based on the selected system option. We will tell you about the technical features of the most popular types of devices of the Russian brand, so that every car owner can use all the available features.
Basic requirements for implementing StarLine autorun
Before remote starting, make sure that:
- the hood is closed, the parking brake is on;
- for cars with a manual transmission - the “program neutral” procedure has been performed (preliminary preparation for starting the engine);
- for cars with automatic transmission - the control lever is in the “PARK” position.
Remote engine starting cannot be performed in the following cases:
- ignition on;
- the hood is open;
- the parking brake is turned off or the brake pedal is pressed;
- preparation for starting the engine on vehicles with manual transmission (“program neutral”) has not been completed.
During one starting cycle, the system can make 3-4 attempts to start the engine. If after the 3-4th attempt the engine does not start, the “OST” or “” icon will be displayed on the display of the remote control with feedback (provided that it is in the reception area) and the remote control will emit 4 beeps.
For more information about StarLine errors during autostart, please follow the link.
SMS commands and voice control
The disadvantage of this method is that in areas with an unstable Internet channel from a cellular operator whose SIM card is installed in the alarm, problems with starting the engine are possible. Therefore, use the more reliable capabilities of the standard GSM channel - by calling or SMS to the phone number of the alarm SIM card.
When you call, the answering machine will work, which will first ask you to enter the PIN code specified when setting up the GSM module from the keyboard (if the call is not made from the main phone). After this, a greeting will sound and an invitation to dial the command code. If you have forgotten the code for the one you need, then press 0 – the robot will list all available commands.
To start the motor, use two commands - 21 and 26. In the first case, the robot will report the success of the start and remain on the line to receive subsequent commands; in the second, after the report, the call will be automatically dropped. The second option makes it possible to use the phone as a control panel by writing the start command in the directory as a telephone number in the format +7ХХХХХХХХХр26 and selecting this entry in the directory or entering it in the speed dial menu.
To turn off the engine, use command 20 in the same way.
Please note that by default, autorun control is available only from the number that is set as M1 in the settings. If you intend to use an additional phone (of another family member), which is set in the settings as M2, then first activate extended access for it using the SMS command 009401.
The launch is controlled via SMS; for this, a command in the appropriate format is sent to the alarm SIM card number:
- For the owner’s main phone: directly specify the command code (21 for starting, 20 for silencing).
- For the M2 phone, if control is allowed: in the format XX00YYYY, where XX is the command code, 00 is the required separator, YYYY is the pin code.
In sixth-generation systems, the syntax of SMS commands has been expanded: to control autorun, use digital and symbolic codes.
- engine start: ENGINE+, D+, D+
- engine shutdown: ENGINE-, D-, D-
Something else useful for you:
Repair and service of cars, engines and automatic transmissions
The procedure for preparing for autostart on mechanics
Depending on the ignition support option (programmable function), to turn on the “soft neutral”, perform the following steps:
- set the parking brake;
- turn off the ignition;
- the display will show r99, if the turbo timer mode is programmed, r06 will be displayed (the LED indicator will be constantly on and the engine will continue to run);
- remove the key from the ignition switch;
- get out of the car and close all doors;
- turn on security mode.
The engine is prepared for autostart.
How much does the A9 kit cost and what does it include?
The Starline A9 alarm system can still be found on sale in some retail outlets. Its cost is low and amounts to approximately 44-46 dollars (the price is current as of 10/05/18).
The anti-theft complex includes:
- central control processor;
- transmit-receive device in a plastic case with an antenna;
- interior and engine temperature sensors;
- control panels (main, with LCD monitor, and additional, without screen and feedback);
- shock sensor;
- indicator light;
- Valet service switch;
- wiring and connection plugs;
- hood button;
- instruction manual (in Russian).
StarLine Twage A8 A9 A4 A6
StarLine A4 and A6 systems do not have the ability to start the engine.
Option 1 By pressing button 3 of the key fob, move the cursor to the “Start” icon and briefly press button 2 of the key fob.
Option 2 Press button 1 of the key fob for 3 seconds and release. If button 1 is unprogrammed or faulty, use the first option or program the first button.
Minuses
The above disadvantages most likely apply to cars with a manual transmission.
Minuses:
- Fuel consumption increases.
- In winter, icing of the exhaust pipe occurs (this occurs due to water condensation that forms in the exhaust system).
- In winter, freezing of handbrake cables or brake pads (when the car is parked in neutral).
- If the car is parked on a slope, the handbrake mechanism is weakened - there is a risk of the vehicle moving spontaneously.
- At the moment the autostart is turned on, there is a threat of vehicle theft, since the security system is turned off at this time.
The car owner, only after meaningfully weighing all the pros and cons of autostart, will be able to decide whether it is worth installing the system on his vehicle.
StarLine E90 E91 E93 E60 E61 E63
Alarms E60 E61 E63 do not have the ability to start the engine.
For StarLine E90 E91 E93 systems, two options can be used depending on the firmware (if the firmware is newer, then most likely the first launch option is used).
Option 1 Press button 1 on the key fob for about 3 seconds (until two melodic signals appear), then release the button, the engine will start.
Option 2 Remote engine start is carried out by sequentially pressing buttons 1 and 3 of the key fob. press button 1 long for about 3 seconds (until a beep sounds), and then button 3 briefly.
Possible faults
But sometimes the system can produce various errors: the engine does not start or starts, and after a few seconds it stalls. In such cases, the letters SP or ST are written on the key fob. The main reasons why the alarm system fails are listed below.
First of all, you need to figure out whether the car has an immobilizer. The fact is that this security system does not allow automatic start-up. Therefore, during installation it is important to use the standard blocker bypass module.
The processor simply cannot read the command from the key fob. There may be several reasons for this: from a dead battery in the remote control to a short circuit or software malfunction.
There is no alarm connection to the starter and engine control parts. It turns out that the system simply does not have the physical ability to start the engine. It is necessary to install the missing elements.
If the car is equipped with a manual transmission, there is a possibility that the neutral mode has not been programmed. This aspect needs to be corrected.
System installers may incorrectly connect the motor control circuit or connect not all wires. Also, the transponder in the module may simply not recognize the signal. Or there may be a break in the circuits. In this case, it is necessary to carry out a comprehensive diagnosis.
StarLine D94 B94 D64 B64
The D64 and B64 systems do not have the ability to start the engine.
For StarLine D94 and B94 systems, two options can be used depending on the firmware (if the firmware is newer, then most likely the first launch option is used).
Option 1 Press button 1 on the key fob for about 3 seconds (until two melodic signals appear), then release the button, the engine will start.
Option 2 Remote engine start is carried out by sequentially pressing buttons 1 and 3 of the key fob. press button 1 long for about 3 seconds (until a beep sounds), and then button 3 briefly.
Connecting the A9 alarm
The Starline A9 car alarm circuit, which is included with each car protection kit, is quite simple and understandable to the average car enthusiast. You can connect the system yourself if you have certain skills in the field of automotive electrical engineering. The connection diagram can be viewed below:
The basic principle of operation is strict adherence to the instructions, according to which you can connect and configure the car alarm without problems.
StarLine A92 A94 A62 A64
StarLine A62 and A64 systems do not have the ability to start the engine.
Option 1 Remote engine start is carried out by sequentially pressing buttons 1 and 3 of the key fob. press button 1 long for about 3 seconds (until a beep sounds), and then button 3 briefly.
Option 2 To remotely start the engine, place the cursor on the “Fan” icon; to do this, briefly press button 4 two or more times to move the cursor and briefly press button 3.
Video “How to make a module for remote start of an internal combustion engine with your own hands”
User Oleg Shevyakov talked about making such a unit for his car on his own.
Sorry, there are no surveys available at this time.
Do you have any questions? Specialists and readers of the AUTODVIG website will help you ask a question
Was this article helpful?
Thank you for your opinion!
The article was useful. Please share the information with your friends.
Yes (100.00%)
No
X
Please write what is wrong and leave recommendations on the article
Cancel reply
Rate this article: ( 3 votes, average: 5.00 out of 5)
Discuss the article:
StarLine A93 A93v2 A63 A63v2 A36 A39
For StarLine A93, A93v2, A63, A63v2, A36 and A39 systems, autostart can be enabled in two ways depending on the firmware (if the firmware is newer, then most likely the first startup option is used).
Option 1 Press and hold button 1 on the key fob (until two melodic signals appear), then release the button.
Option 2 Remote engine start is carried out by sequentially pressing buttons 1 and 3 of the key fob. Press button 1 long for about 3 seconds (until a beep sounds), and then press button 3 briefly.
Installation
Each car alarm is installed in accordance with its instructions. In this matter, of course, it is better to trust the professionals. After all, not only the warming up of your car depends on how it is installed, but also whether it will be stolen.
In the case of self-installation of a car alarm, the algorithm of actions will be basically similar for all system manufacturers. Therefore, let’s look at how to install car autostart using the Starline key fob.
The central unit of the system is located in the vehicle interior. It is most convenient to place it under the dashboard. There, moisture will not get on it, and the length of the connecting wires will be reduced to a minimum. The block is secured with self-tapping screws. This is necessary so that it does not move during vibration. The paging decoder is placed near the block.
The siren finds its location under the hood of the vehicle. Its horn must be lowered down - this way you will avoid collecting water in it. The siren should be kept away from sources of moisture and heat. Be sure to check that the wires are inaccessible from the outside of the hood.
Place the shock sensor in the vehicle interior. LED indicator on the panel. It must be in a visible place. The service button, as well as the central unit, must be hidden from prying eyes. But unlike the latter, place the button within reach.
After installing push-button switches in the trunk and under the hood of the car, they should be checked.
Try to lay all wires away from electrical interference, moving structures and other elements of the car, which may subsequently interfere with the normal operation of the car alarm.
The main assistant when installing a system such as autostart for a car is auto circuits. Schemes for cars are in the instructions for the system. It is through them that all car alarm components are connected.
Other StarLine models
StarLine A65 A66 A67 A95 A96 A97 StarLine B95 B96 B97 B66 StarLine D95 D96 D97 StarLine E63, E65, E95, E66, E66v2, E93, E96
For these systems, two options can be used depending on the firmware (if the firmware is newer, then most likely the first launch option is used).
Option 1 Press button 1 on the key fob for about 3 seconds (until two melodic signals appear), then release the button, the engine will start.
Option 2 Remote engine start is carried out by sequentially pressing buttons 1 and 3 of the key fob. press button 1 long for about 3 seconds (until a beep sounds), and then button 3 briefly.
How else can you enable Starline autorun?
- By triple pressing the security button of the standard ignition key with a pressing interval of no more than 5 seconds (the availability of this function depends on the car model.
- From a mobile application if the system has a GSM or BT module.
- From an additional keychain.
- It is also possible to configure autostart based on engine temperature, time and battery discharge.
If any option does not suit your alarm model, then you can always find out which button to turn on autostart in the instructions.
What to do if Starline A93 does not allow you to start the car
Using any equipment is never completely problem-free, and the Starline A93 signaling system is no exception. From time to time, owners have to deal with a situation where the car plant is not working. The main reasons for this are usually:
- failure in programming the alarm memory;
- incorrect operation of the control unit;
- temperature controller failure;
- operation of the motor blocking relay;
- negative balance of the mobile account of the owner or device.
In the first case, the problem is due to the fact that each key fob is registered in the gadget’s memory separately. And from time to time, failures occur, leading to the inability to recognize the remote control from the signaling side. It can be solved by flashing the firmware.
Failures in the control unit system are one of the main problems that module owners have to face. The main obstacle to successful elimination is the impossibility of effective diagnostics at home; it is necessary to contact specialists who can both check the device and repair it.
The third problem most often occurs during the cold season, when there are low temperatures outside. The controller is not able to correctly determine the temperature of the engine itself and it does not start. The solution is to replace the broken mechanism.
The lockout relay should not operate in this situation, so if this happens, it is most likely time to replace it.
As for the account balance, the obvious solution is to top it up.
