Hello, dear friends! At one time, angel eyes on BMW cars made a splash on the market. It was optics of amazing beauty, especially in the dark. But even now fashion has not disappeared, and many people want to make angel eyes with their own hands.
In practice, there is nothing particularly complicated here. You will have to tinker, but the result will certainly please you. You can start from different instructions and manufacturing options. Some people use sites with videos that can be watched in parallel with taking notes in a notebook. Also on the Drive2 resource, motorists share their own experience of making peepholes, like those on a BMW.
I suggest you consider 3 interesting options. 2 of them are homemade and one more can be purchased online. The kit usually includes an ignition unit or a stabilizer, depending on the light source used.
Why the trunk does not open on a Ford Focus 2 and how to fix it
- 5 mm white LEDs;
- a resistor of approximately 330 Ohms and 0.25 W;
- wires for connection;
- plastic rod;
- or a plexiglass rod (diameter from 8 to 10 mm);
- jar or lid (1-3 liters);
- drill with adjustable speed;
- soldering iron;
- silicone glue;
- construction type hairdryer.
Take a rod of suitable length to make a ring out of it. You will need to make holes on the end sides for installing LEDs.
To avoid damaging the rod, it is recommended to wrap it in polyethylene or fabric and then fix it in the machine. This will ensure immobility and the ability to carefully make indentations without scratches.
Typically the holes are made with a diameter of about 6 millimeters. The depth depends on the design of the tube itself. But it is better not to exceed the value of 10 millimeters. To make the body take the shape of an optical device, you can take a jar or a lid from it. By bending around the jar, you will get a perfectly even ring. It is important that the diameter matches the internal diameter of the headlight itself on your car. Using a hair dryer, the body heats up and bends around the jar or its lid. There is no need to completely connect the ends of the tube to each other.
At the next stage, diodes are installed. Here you need to solder a wire of a suitable length to the terminals, which is enough to connect to the power wires outside the car headlight housing. A resistor is soldered onto one wire. As a result, you need to assemble an electrical circuit of LEDs with a serial connection and the resistor itself.
Now insert the diodes into the holes of your tube and secure with glue. The number of LEDs is determined individually.
In this case, you should not count on a bright glow and the ability to replace DRLs. The option is rather decorative.
Installation of angel eyes
After making or purchasing a set of glowing eyes, they need to be installed in the headlights. The installation process itself does not depend on the make of the car and on what kind of eyes are available: homemade LED or purchased CCFL tubes. The main thing is to be able to carefully disassemble and reassemble the headlights. To carry out the work you will need:
- construction hair dryer;
- transparent two-component glue;
- a set of screwdrivers and other tools.
The first step is to dismantle the headlights. There are no general rules in this matter, since each machine has design features and requires an individual approach. After dismantling, you should carefully inspect the headlight for the presence of latches at the junction of the two parts. Then it is placed on the table and for several minutes the seam area around the entire perimeter is heated with a hairdryer to warm up the sealant there. Only after this they start unpacking. It is better to do this work together, when one person holds the body and heats the seam with a hairdryer, and the second person gradually divides it into two parts.
You need to wear gloves when working with a disassembled headlight to avoid leaving fingerprints on the reflector.
Having separated the inner mask with the reflector from the glass, you can begin installing the first luminous eye. To do this, apply it to the mask and determine the location of the wires. Apply glue to the degreased surface of the ring, press it against the reflector and leave until completely dry. Glue the second ring in the same way. The headlight is assembled in the reverse order, heating the seam with a hairdryer and pressing the glass tightly against the body.
Please note that these instructions are general and only suitable for some types of headlights. Therefore, in each specific case, it is necessary to take into account the design features of the car.
Two-axle passenger trailer: design, reviews, which one to buy
- to Priora;
- Toyota Chaser 100;
- BMWs deprived of such a privilege;
- VAZ 2106;
- VAZ 2109;
- 2110;
- VAZ 2115;
- VAZ 2114;
- Renault Logan;
- Hyundai Solaris;
- Daewoo Lanos, etc.
Objectively, angel eyes look more advantageous on foreign cars. Although no one will forbid you to install such solutions on any machine.
To implement the task, you will need to prepare a slightly different set of materials and tools.
The following is required:
- double-density white LED strip, but without silicone coating;
- wires for connection;
- transparent silicone;
- glue;
- varnish (silver color);
- screwdriver;
- pliers;
- Have a good mood;
- extreme concentration and accuracy.
LED strips bend perfectly, which will allow you to easily make a ring of the required diameter. Just keep in mind that one headlight requires about 30-40 centimeters of tape.
Then the pads at one end are stripped to allow additional wires to be soldered there. They allow you to connect to a +12V power supply.
Next, a piece of tape is pointed onto a flat surface with the diodes facing upward. Gradually the tape is filled with transparent silicone. Do this slowly and carefully, armed with a mounting gun. This will allow you to coat the diodes with a uniform and even layer of silicone. It is important to wait for the resulting structure to dry completely, otherwise you will ruin everything with your own hands. Silicone will protect the product and act as a light diffuser.
To avoid wasting light illuminating the reflector, coat the back side of the tape with silver varnish. You can borrow it from your wife, sister or mother. Or buy it at your nearest store. The varnish will act as a reflector.
Connecting Angel Eyes
Angel eyes are an additional lighting device for a vehicle (vehicle) and inherently fall within the requirements for daytime running lights (DRLs). In accordance with clause 6.19.7 of GOST R 41.48-2004, running lights must turn on when the engine starts and turn off when it stops. In addition, turning on the headlights should lead to the DRLs turning off, so connecting the angel eyes must be done in accordance with a specific DRL connection diagram. It follows that the connection of angel eyes according to all the rules can be realized through a five-pin relay or through the DRL control unit.
To implement the first option, you will need female terminals (4 pcs.) and a 5-pin relay, the connection diagram of which is shown in the figure.
As can be seen from the diagram, the negative wire from the angel eyes is connected to the car body, and the positive terminal is soldered and connected to contact No. 30 of the relay. Then, under the hood, they find a wire connecting the side lights to the switch and run another wire with a terminal parallel to it, putting it on contact No. 85. Another long wire will run from the “Ignition + 12V” terminal block to contact No. 87a. The last one to connect contact No. 86 to the car body. During the connection process, all terminals, including unused terminal No. 87, are insulated using heat shrink tubing.
If an ignition unit (current stabilizer with LED rings) is supplied complete with CCFL rings, then it should be connected between the 30th pin of the relay and the eyes. In general, any LED DRLs must be operated together with a current or voltage stabilizer (for LED strips) to avoid the influence of voltage surges in the 12 V on-board network.
The second option involves connecting angel eyes through a DRL control unit (DRL controller), which can be purchased at any auto store. In this case, assembly is carried out in accordance with the diagram given in the instructions for the product. The use of industrially produced DRL control units is the best option for connecting angel eyes, as it is easy to assemble, provides overload protection and guarantees long-term, safe operation.
Third method
In theory, it is the simplest, since you are simply buying a ready-made device, which has a diffuser, an ignition unit and other necessary components. It’s just important to choose a quality product, since the Internet offers many options that are not of the best quality.
Eyes based on CCFL rings have proven themselves to be excellent. They have high reliability indicators and are in many ways superior to their LED counterparts.
If we talk about Aliexpress, then I would not advise you to buy ready-made angel eyes based on LEDs. Low-quality products are used here, which can quickly overheat when the head optics are turned on. As a result, in less than a year they will have to be removed due to the significantly reduced brightness level.
Why are owners of cars with such tuning fined?
Owners of cars in which such tuning is legally included in the vehicle package should not be afraid of claims from law enforcement agencies. Everything here is legal, correct, fair. But when installing it yourself, you need to be guided by legal acts regulating the lighting of the front and rear of the car. In traffic rules, codes of offenses, government regulations and GOSTs regulating safety requirements for technical condition, angel eyes are not directly mentioned anywhere.
But there is a legal requirement according to which white lights can be used on the front of the car (dimensions and headlights), as well as orange lights for turning lights. Eyes of other colors are not allowed and will result in a fine.
Blue color is outlawed
Therefore, there is no need to install yellow, red, green, purple and other colors in the headlights. We can advise all drivers CAUTION: you need to install angel eyes CORRECTLY, although even this advice does not guarantee problems when passing a technical inspection.
How to connect a voltage stabilizer (optional)
In the electrical on-board network of the car, the voltage “walks” from 12 to 16 volts. And LEDs do not tolerate such changes well. We soldered a resistor to each LED to regulate the voltage. But for more reliable protection you need a special stabilizer. It’s easier to buy a ready-made version and arrange it into a connection between the “angel eyes” and the on-board network of the car.
Factory version of the voltage stabilizer
If you are an “advanced” electrician, you can solder a simple stabilizer yourself. The L7812CV chip is used as a basis. See the photo below for the connection procedure.
The connection diagram is quite simple
According to this scheme, you need to connect the negative contact of the LED to the ground of the car, and the positive contact to the output of the stabilizer.
Video: connecting a voltage stabilizer for LEDs
The procedure for making and installing “angel eyes” is not easy. Before starting work, evaluate your abilities and capabilities to avoid possible additional costs. Consider whether your actions are legal and what consequences they may lead to. Neatness and cleanliness are required for successful completion of optics tuning. But everyone will notice your efforts.
Adjusting the parking brake on Kalina: the need for the procedure and step-by-step instructions
How to choose the best navigator. Instructions for flashing Prology iMap-400M
Reprocessing an old headlight
First you need to remove the headlight and separate the glass. However, this is not so easy to do, since it “sits” securely on the sealant. Therefore, we take a construction hairdryer and heat the product to melt the factory glue (you should not heat the central part of the glass surface so that it does not burst, only the side seams). Some heat the headlights in the oven for 10-15 minutes at a temperature of 60-80 degrees.
But sometimes the sealant does not soften. Then you can try to pick up the glass with a screwdriver and carefully separate it from the reflector along the seam. However, often such manipulations still lead to damage to the surface, so for those who do not want to suffer, it is easier to immediately buy new glass for the headlight (can be found for 50-100 rubles) and work with it.
Healthy! Old glass can be placed in a bag and carefully broken (the fragments will remain in the polyethylene). After this, all that remains is to clean off the old glue and remove any remaining glass along the seams of the headlight.
Decoration Features
Today, the simplest and most effective way to modify the exterior of a car is the so-called. "angel eyes" This tuning consists of luminous rings installed on the headlights. These rings are installed on the front optics of the car. For the first time, such a unique solution appeared on BMW products. After some time, luminous rings for headlights began to be sold as a separate vehicle upgrade. Note! Today, “Angel Eyes” can be either purchased in a store or made with your own hands. At the same time, their production is quite simple and many car enthusiasts prefer the second option for their car.
"Angelic" car tuning
It is worth noting that purchased angel eyes for a car are made from special neon tubes. They are bent and installed on the headlights. The installation also uses an ignition unit. After installing this optical system on the headlights, the light turns out more pleasant and bright. Separately, it is worth noting that some drivers use such tuning as daytime running lights or dimensions. Today, such car decoration is very popular and is very common. This is due to the fact that they can be installed on the headlights of a wide variety of car models (both domestic and foreign). For different car models, this type of tuning may differ in basic parameters:
- dimensions;
- glow color;
- ring diameter.
If everything is done right, you will get an exclusive car.
Can I use red lenses?
Technically, the backlight can be any color, but don't choose blue and red. Traffic police officers regard the use of such colors in optics as an imitation of “flashing lights”, and will definitely want to talk to you about this. In extreme cases, they may even take the car to the impound lot. They react calmly to white, yellow or orange “angel eyes” (in most cases). Multi-colored lights are often considered by traffic police officers as a challenge and immediately cause an appropriate reaction.
What are the penalties for violation?
For those who like to argue, here are excerpts from the traffic rules.
clause 12.4 part 1 Installation on the front of the vehicle of lighting devices with red lights or red reflective devices, as well as lighting devices, the color of the lights and the operating mode of which do not comply with the requirements of the Basic provisions for the admission of a vehicle to operation and the duties of officials to ensure BJJ.
https://www.drive2.ru/c/1296154/
For those who are slow-witted, sanctions are provided in the form of fines:
- for citizens - 2.5 thousand rubles;
- for officials - from 15 to 20 thousand rubles;
- for legal entities - from 400 to 500 thousand rubles.
In addition, unauthorized devices and devices are confiscated. The violator also faces a ban on the operation of the vehicle with the removal of the seal.
Traffic police inspectors will probably issue a fine for such tuning.
SMD technology
SMD (Surface-mount LED). In this version, the LEDs are installed in a circle on a round board. They provide very high light output. There are many styles of these rings, depending on the number and size of LEDs. SMD LEDs are mounted in a circle and create a glow in individual points. Many people like this particular look, while others want the luminous rings to be more uniform and continuous. This is done using a diffusion housing that is placed on top of the LED ring. However, this creates additional heat build-up, which reduces the lifespan of the LEDs.
“Angel eyes” SMD without diffuser and with diffuser.
SMD LED angel eyes can be with resistors or adjustable. The most common method for making SMD LED angel eyes is to mount resistors directly on the ring to control the power that goes to the LEDs. This method is quite reliable, but under certain conditions the resistors on the ring itself may become subject to excessive heat. Additionally, voltage surges can occur in a car circuit, also adding voltage to the resistors. Over time, with constant voltage, resistors may fail or operate intermittently.
To completely eliminate the problem, LED rings have been developed that do not use resistors on the rings. There are only LEDs there. To provide constant current, a regulator unit is used, which is less susceptible to voltage and temperature changes. It is attached along the line between the power supply and the LED ring. This technology allows you to install more LEDs on each ring of angel eyes, which gives a more uniform glow. It is more convenient to mount such rings, since the reverse side does not contain resistors and fits well to any surface.
