Installation and connection of a glass closer on Lada Granta, Kalina. niva. 4x4, etc.

When replacing power windows, first disconnect the negative terminal of the battery.

Removing and replacing the window lift mechanism

Replacing the cable without dismantling the entire window regulator is quite problematic, therefore it would be more convenient to remove the entire mechanism. First, you need to lower the glass so that you have access to the brackets securing the glass to the window lifter; unscrew the two fastening bolts with a “10” head.

Next two options

, it would be more convenient to completely remove the glass by turning it slightly counterclockwise, but removing it from the door can scratch or damage the tinting; to avoid this, simply secure the glass with tape.

Next, with the same head, both nuts of the middle fastening, one nut of the lower, and one of the upper fastening of the guide of the lift mechanism are unscrewed.

The plastic socket is removed from the slot of the handle, and the three fastening nuts are unscrewed with an “8” socket head. Now you can remove the window lift mechanism assembly through the door access window.

If the glass was removed completely and the guides were turned away, its correct position in the opening is regulated by moving the bolts in the oval holes of the bracket.

Many VAZ 2110 cars are equipped with electric windows; to dismantle such a mechanism, the principle is the same

, with the only difference that first of all it is necessary to disconnect the switch from the gearmotor, then the lift is removed and the gearbox itself is disconnected.

After removing the entire VAZ 2110 window lifter mechanism, the drive cable is easily replaced with a new one. Assembly is carried out in the reverse order of disassembly. If you have provided new holders (pistons) in advance, no problems will arise.

When installing the glass lift handle, pay attention to the tightness of the fit; if it is loose, you can wrap the slot with a layer of electrical tape or fume tape, pressing it into the grooves of the slots

Main causes of failure

Most likely the power window fuse is at fault.

The angle is not good, but this is exactly what the mounting block looks like when you look at it from above

From the situation you described, it follows that the fuse is to blame. There are enough symptoms and prerequisites for its breakdown. First, you raised one glass, which is already good, since raising both windows at the same time is not recommended due to the increased load. Then they started to lift the second window, and the fuse burned out.

If one of the glasses works, then the fuse is good.

The button is broken

The power window buttons in the Norma configuration usually do not cause problems

If only one of the two or four power windows does not work, depending on the configuration and equipment of the car, then the problem is most likely in the button or in the wiring to it. It is necessary to remove the front door trim and ring the buttons, you can also look at the voltage on them.

Front passenger window button

Motor failure

Appearance of the new motor (purchased to replace a broken one)

The window lift motor on the Lada Granta rarely causes problems. This part is reliable, but it can also fail. You can check the motor by applying voltage to it forcibly, that is, directly from the battery.

Replacement of front electric windows of Lada Granta

You will need: a flathead and Phillips screwdriver, a 10mm wrench and remove the front door trim.

Front ESP mounting diagram:

1. glass guide fastening nut; 2. nut for fastening the gearmotor; 3. glass holder bolt; 4. block with electric drive wires.

First you need to remove the Granta door glass; to do this, you need to lower it to its lowest position. Further:

• Remove the door trim mounting bracket by removing 3 bolts.
• Remove 2 bolts (according to diagram No. 3), holding the glass.
• Remove the front door glass by lifting it up and turning it in the door opening.

To remove the Lada Granta power windows you need:

• Unscrew the 8 nuts securing the glass guides (No. 1 according to the diagram), as well as the 3 nuts securing the window lift motor to the inner door panel (No. 2 according to the diagram).
• Remove the window lift mechanism assembly with the gear motor from the door cavity.
• The photo shows the assembled ESP Grants.

Installation of window regulators is carried out in the reverse order.

Relays and fuses Lada Granta

Fuse and relay box in the passenger compartment

To access the mounting block, pull the bottom left corner of the cover to release the left locking point 1, then release the middle bottom point 2 and the two right locking points 3 and 6, then release the top locking points 4, 5 and remove the cover.

Installation of the cover is carried out in the following order: first snap the right fastening elements of the cover at points 6 and 3, then snap the lower fastening elements of the cover at points 2 and 1, then the upper ones at points 4 and 5.

New mounting block

Fuse box in the engine compartment under the hood

Please note that there are different variations of this block.

Connection option 1

1. 30A Low beam headlights or main relay, circuits protected by fuses F1 and F21 of the mounting block in the passenger compartment 50A Windshield heater
2. 60A Generator VAZ-2190
3. 60A Generator
4. 30/40A Heater fan (heater fuse grants)
5. 50A Electromechanical power steering
6. 60A ABS block

Connection option 2

1. 60A Generator
2. 60A Generator
3. 30/40A Electric radiator cooling fan
4. 40A ABS/ESP
5. 25A ABS/ESP
6. 50A Electric Power Steering Controller

Connection option 3

1. 30A Low beam headlights or main relay, circuits protected by fuses F1 and F21 of the mounting block in the passenger compartment
2. 60A Generator
3. 60A Generator Lada Granta
4. 30A Heater fan (heater fuse grants)
5. 50A Electric power steering

Removing the power window mechanism for the front door of Lada Granta

Tool:

• Open-end wrench 10 mm
• Small flat screwdriver
• Medium Phillips screwdriver
• Driver for socket attachment
• 8mm wrench attachment
• Scissors

​Parts and consumables:

Notes:

Carry out the work to replace the window lifter mechanism. The operations for removing the front door window regulator are similar.

1. Place the glass in the upper position.

2. Disconnect the wire terminal from the negative terminal of the battery, as described in this article.

3. Remove the front door trim as described here.

4. Tape the glass to the door frame.

5. Loosen the glass holder bolts.

6. By pressing the latch, disconnect the wiring harness connectors of the window lift motor gearbox.

7. Using an 8 mm socket, unscrew the three bolts securing the door trim mounting bracket and remove it.

8. Using a 10 mm socket, unscrew two nuts 1 of the upper and lower fastenings of the two guide sliders of the window lifter to the inner door panel and three nuts 2 of the gear motor fastenings.

9. Remove the power window mechanism from the door through the lower rear access hole in the interior panel.

10. Install the power window mechanism in reverse order.

Source

Specifications

The power window operation mode is short-term. After ten lifting and lowering of the glass in continuous mode, it is recommended to take a break from work for at least 10 minutes.

Lada Granta 2012, 87 l. With. - breakdown

Lada Granta, 2015

Lada Granta, 2015

Comments 12

Hello everyone, I also have a grant, but the right window lifter does not work for me

Hello. I have the same problem, and I also have window closers, the right lift has stopped working. How did you solve the problem?

I didn’t decide, I gave up, every other time it either works for me or doesn’t, I just started lifting the windows with my hands (like this is more reliable than checking every time whether it’s up or not)

Good day!

When I press the button on the right front passenger window, the window goes down all the way and immediately returns up (LADA GRANTA luxury).

What could be the reason?

I would like to inform you that an additional security alarm was installed along with the standard one.

My right one is also having some nonsense

=) That’s right... the button is dead, the power window buttons are connected in series

This happened to me, and I thought the engine was dead. But it turned out that the button is the brain... I disassembled and reassembled everything works

I stopped by the service center, one of the electricians said, go to the officials, you’re not the first, supposedly the engine of the grant is bent, I’ll talk to them tomorrow, everything would be fine, but the officials are in another city 60 km from mine, I work until half past six , after work, either rush or ask to take time off earlier.

But the most annoying thing is that they will have to leave the car to get home - figure out how to do it yourself, and...

I have a major Shumka there, but I feel like they won’t stand on ceremony, they’ll tear everything up, so when I get there, I’ll ask what holes they need, and I’ll tear them off as needed =) (there’s a possibility that they’ll also come after me, saying, well, I shorted the Shumka there =) )

Download books on Lada Granta

Here are several PDF books on Grant - high-quality color diagrams of electrical equipment, repair and operation manuals, and many other useful things.

• Download Lada Granta service manual
• Download wiring diagrams for Lada Granta
• Download Lada Granta instruction manual
• Download a book on car repairs VAZ-2190

Finding the cause of a broken window regulator

The power windows can be activated when the key is inserted into the ignition switch and in the “ON” position. If nothing happens when you press the power window up/down button, it is likely faulty. To fix the problem, you need to understand why the problem occurred.

Fuse box

Checking the power window system to detect a failed element is carried out as follows:

If the power windows refuse to work, you need to check the circuit breaker or fuse, it is quite possible that it has blown. If only the rear power windows stop functioning or if they respond to control only from the main unit (i.e. the buttons on the doors do not work), you need to check them for current conductivity. If the malfunction has not been detected, you need to inspect all the wires connecting the system elements to each other for integrity. If a break is found, the connection should be restored. If you cannot lower/raise only one window using the main power window control unit, you should try to do this using the buttons that are embedded in the door trim. If the glass manages to move, you should check the operation of the main power window control unit. A possible reason for the failure of one of the window regulators may be the failure of the electric motor.

In this case, it is worth checking its voltage and wiring, for which you will need car electrical circuit diagrams. You should also pay attention to the possibility of mechanical damage to the guides along which the side glass moves.

If upon inspection it is discovered that they are bent, then most likely this is the reason why the movement of the window regulator is difficult.

Motor

Most often, car owners have to deal with problems with the wiring that connects the elements of the window lift system and the failure of electric motors. The main reason for their breakdown is the active use of power windows, frequent opening/closing of windows, as well as obsolete wiring.

Before you fix the problem, you will have to spend a lot of time trying to understand why the power windows are not working. You can abandon the idea of ​​independently searching for the cause of their breakdown and turn to experienced car electrical technicians. This is the best solution to the problem in case of lack of free time.

Power window doesn't work

Modern, well-equipped cars are always equipped with electric windows. The presence of such a function is no longer a special innovation, but, nevertheless, it is appreciated by numerous motorists for the convenience that this system provides.

However, during the operation of their car, car owners often notice how poorly the window regulator works, that it does not respond to pressing a button or periodically jams. To understand what happened to this element, you need to have an idea of ​​the window lift system as a whole and the principles of its operation, and only then start troubleshooting.

Components of the window lift system

The power window system operates thanks to electric motors that are built into car doors and are responsible for raising and lowering the side windows. The electric window system includes the following elements:

regulators (electric motors);

Operating principle of electric windows

The electrical control system, as a rule, has a trapezoidal design that ensures easy lowering and raising of the windows when the corresponding buttons are pressed on the main switch block, which is either located next to the driver or is embedded directly in the door cards. An independently functioning motor is installed inside each door, which is capable of working in two directions, raising the glass up and lowering it down. The power window system on modern cars includes special relays that control the electric current going to the window motors.

Installation

For installation, no special fixtures, instruments or other equipment are required. The entire installation process is trivial and will be simple for any male person. The main thing is to have desire and skillful, masterly hands. Before starting the installation, you need to purchase a five-pin standard relay for VAZ car models in advance. Then the door closer itself is installed; all you need to do is run a wire under the door trim and that’s it. But the most important role here is played by the alarm system, since a free open channel comes from it, to which the automatic glass closer system is connected.

Through this signaling channel, a negative pulse is sent, which polls the sensors.

When you have already reached the finish line of installing the closer, you must disconnect the negative power cable from the battery . This is a kind of protection against short circuits that can occur and damage the entire electrical wiring of the car. These actions must be completed without fail.

The next step is to remove the door card from the driver's door. When removing, you need to act carefully so as not to damage or deform it. If it is not available, then it is better to buy hedgehog clips in advance. The new ones are better, there will be no worries about poor fastening.

After this, the connectors are removed from the power window control module in the Lada Granta model.

How to remove the power window button on a grant

Electric window switches are installed in the door trim. A block with switches for all electric windows is installed on the driver's door. Depending on the configuration, some vehicles may have power windows installed in the rear doors.

To remove the switches, it is advisable to dismantle the door trim, since if you try to remove it by prying it with a screwdriver, there is a high probability of damaging the trim and the switch itself.

The operation is shown using the example of a switch block on the driver's door. Removing and installing the power lift switch on the passenger door is performed in the same way.

1. Remove the door trim

2. Squeeze the two latches.

and remove the power window switch block.

You can check the switch with a multimeter in ohmmeter mode. The switching of the switch terminals is shown in the general diagram of the electrical equipment of the car.

Join our club, share your first impressions of the car, start your blog on our website. In the near future we will hold a competition for the best review of the Lada Granta.

As you understand by the locations of the reeds

But on the driver’s side (there are no sides here, only two in front and two in back)

The module is removed in the same way, but either with two screwdrivers or something wide (I didn’t remove it a second time for the sake of the photo. I actually removed it while removing the casing to find where these tabs are.)

Then we take them home. They are held in place by 5 latches (two on the side and one) I pushed a cap under each, and then pulled the 5th with a screwdriver and pulled it out

Don't lose these things:

They stand on both sides of the board in the slots

We see the following: The diode itself is circled

Let's solder it. Here it is on the tape side by side: DDD

Next, take a knife and remove the varnish from the tracks in order to increase the area. We tear off, tin, and weld the diode from the tape. Angled towards the larger part of the board

Yellow indicates the corner on the diode. This is checked by supplying 12V to the appropriate terminals. “+” is written on the board, but just in case I noted it in the photo.

It’s easy to assemble: put the main part in place, if the plates fall out, put them back in place. We take the part with the button in our hands and holding it by the body so as not to press the button, we simply snap it into place.

How to choose and where to get window regulators for the Lada Granta

You can buy Lada Granta window regulators at any auto parts store for domestic cars. But what details to choose – we need to talk about this in more detail.

It is advisable to choose articulated or scissor-shaped models. Judging by the reviews, the most popular are:

• hinged models “Granat” - they are reliable, metal construction, high force, complaints about rattling when the glass is open;
• “Forward” rack and pinion models are compact and lightweight, the chain and guide are plastic, they are considered not very reliable, there are complaints about glass distortion;
• the scissor-shaped “Katran” and “Berkut” are made of iron, the advantages are the same as those of the hinged “Granat”, they also rattle on the door when the glass is closed;
• rack and pinion “Granat” - not as reliable as hinged ones from the same manufacturer, metal + plastic construction;
• simple cable models.

Common faults

There are many reasons why the window regulator on Kalina does not work and why the device needs to be replaced, but we will look at the main ones:

1. The electric motor brushes are stuck, usually as a result of overheating of the brush elements themselves, which, as a rule, are not resistant to sudden temperature changes. Accordingly, as a result of heating the brushes, the plastic socket may melt. This will also cause the brushes themselves to lose mobility. If the malfunction has just begun to appear, you can knock on the plastic door lining several times to restore the unit’s functionality. However, over time, this method will no longer be able to produce the required result, so intervention in the design of the joint venture will be inevitable.
2. The cause of the malfunction, which may require replacement of the joint venture, can also be the ill-conceived electrical circuit installed at production. The contacts themselves are not able to withstand the necessary load that is placed on them. The SP system may fail due to the fact that the electrical circuit is not supplemented with a unloading relay. So in the event of a breakdown, it often happens that the car owner has to repair not only the power windows, but also the control panel itself.

As practice shows, in most cases, repairing a unit is either completely impossible, or can be done, but with great difficulty. Accordingly, the best option would be to install a new joint venture (video author - Emilien Ok).

Features of connecting power windows

Unlike conventional mechanical devices, power windows are not equipped with traditional gear reducers, but with a special drum. The shaft of a DC electric motor is inserted into its hole located in the center. In this case, the motor is only a component of the gearmotor, on which, as we found out earlier, the speed and quality of raising and lowering the windows depends.

Before installing a new power window, you must select the correct device based on its technical characteristics, and also make sure that the product is in a fully folded state. Otherwise, you are unlikely to be able to install the product efficiently and ensure its flawless operation after connecting it to the vehicle’s on-board network.

You've probably noticed that on almost all foreign cars the power window buttons are duplicated on each car door. To connect additional ESP buttons in the doors, you need to run an additional three wires into each door.

Standard ESP connection diagram

Changed to this scheme (here without rear ESP)

Connection diagram for additional ESP button.

How the additional ESP button is made on Kalina

To install one duplicate button in the door you will need:

1. 2x contact (plastic connector) block male + female 1 pair
2. Large male terminals 2 pcs.
3. Mom large 2 pcs.
4. Mom little 7pcs
5. Earth 1pc.
6. Power window button 1 pc.
7. Button installation cup 1 pc.
8. Power window button connector 1 pc.
9. Wire diameter 0.75 4 met.
10. Door pistons 7pcs

If your ESP buttons have been moved to the doors. then the insert into the harness for additional buttons will look like this. The meaning is that we need to run 3 wires into each door:

1. Ground (Ground, in theory, can be taken into the doors, but there is not always good contact there, so it is better to run a separate ground wire)
2. +12V “after ignition” (with power window relay at ChYa)
3. Button illumination (take it from the cigarette lighter, since it is in the middle between the doors.)

Disconnect the negative terminal from the battery.

We look for +12V on the ESP relay (black and white wire) to it and screw both of our red +12V

Then we climb through the door. There are 2 wires going to the ESP motor - gray and blue, through a connector. Unplug the connector:

We take 2 wires (I have black and black and white), of such length that we can reach from the original chip with the blue and gray wire going into the corrugated door to our future button. We crimp 2 large male terminals onto them and insert them into the connector. We put it on the chip with blue and gray going into the corrugated door, so that the black comes from the gray, and the black and white from the blue:

Insert the wires into the button connector:

1. Red +12V
2. Black mass
3. White backlight
4. Black with gray wire chips
5. Black and white with blue wire chips

We crimp with small “mothers” and insert the ESP buttons into the connector. We do it according to the scheme:

1. Red +12V to slot 2
2. Black ground - in slot 5
3. White backlight - in slot 4
4. The black wire from the gray wire of the chip goes into slot 6
5. Black and white from the blue wire chips - into slot 3 (THREE).

Don’t confuse the button connector sockets! That’s not all, we need two more short wires, through which we will now connect our button to the ESP motor, like we’ll do it as it was. For beauty, we take the same colors of wires that were attached to the original chip going to the door from corrugated material, i.e. black and black and white. It will be like a continuation of the original wires, and in the middle of them is our button. We insert the black wire into socket 1 of the button connector. Black and white - into socket 7. We crimp the other ends of these wires with large “mothers” and put the purchased connector on them so that when putting this on connector to the dangling chip going to the ESP motor:

1. The black wire went to the gray ESP motor chips
2. Black and white - to the blue wire of the ESP motor chip.

In principle, that's all. Don't pay attention to the orange wire in the photo - it's a mass for heating the mirrors.

You can use the button from Kalina. it is more beautiful and a little more expensive than the VAZ 2110.

Electrical circuits of cars VAZ 2110, VAZ 2111, VAZ 2112, repair

Similar products

Do you like the store? Rate it on the Market! Familyevich Evgen

Very good store, I recommend it!

Aminev Maxim

The best window lift store in Russia! :)

Latysheva Julia

Fast? placing and sending an order, complete and accurate information about the order.

Osipov Alexey

They called back right away and clarified the order. The order arrived ahead of schedule.

Safarov Oleg

Well done. You work quickly. And most importantly, the prices are reasonable. Keep it up!!

Nikolay Sotnichenko

Advantages:

Good order processing speed. Pleasant communication from employees.

Flaws:

No.

Ruslan Lukoyanov

I am very pleased with the work of the store, everything is without deception and fast delivery. Keep it up!

Dorofeev Timofey

I definitely recommend the store. Very quickly and clearly. Other online stores could do it.

Vitaly Sukhovlovsky

Advantages:

All liked it

Flaws:

No

A comment:

The order arrived on time, everything is fine, thank you.

Malenkin Roman

Ordered on Sunday, they called back within 10 seconds. Sent on Monday. Lightning-fast comrades! Well done!

Fedotov Nikolay

Advantages:

Excellent shop

Flaws:

No

A comment:

fast, cheaper than other stores, high quality.

Korolev Alexander

Very responsive sellers, after placing the order they immediately called back and discussed the order and sent it out the next day.

Sulin Vladimir

Excellent store, received the order clearly, shipped quickly, received it earlier than expected. The product corresponds to the order. Well done!

Bogumilov Valery

Advantages:

Everything is super, fast and high quality.

Flaws:

No

A comment:

Thank you, well done, everything is high quality and fast.

Bobrovsky Igor

Advantages:

convenient, fast, no problem

Flaws:

No

A comment:

They work quickly and ship quickly. Thank you!

Semyon Semyokhin

Advantages:

Quick response to orders, polite technical support, prompt assistance in any questions that arise

Flaws:

Not found

Read more: Kia Sorento 2 Forum Bohun Orest

Overall only positive impressions. I recommend this store. Prices may even be cheaper than in retail stores.

Arbuzov Valery

Excellent store, quickly received and processed the order. They delivered the parcel efficiently to its destination. Good luck guys. All the best.

Tushakov Rusya

Advantages:

Fast delivery, quality

Flaws:

No disadvantages

A comment:

Shipped quickly, ESP are great to install and use

Gilmanov Sergey

I liked the efficiency, the promptness upon receipt of the goods, the wide selection with delivery of goods, and of course the quality of the brand itself is not great.

super.tatana87

I filled out the application incorrectly myself, ordered a call back, they called me back right away, everything was corrected, I really didn’t expect this, the coolest online store

Borisov Vladislav

A little more than three hours passed from the moment of order to delivery. and this is on a WEEKEND day. Well done. A worthy example for other online stores!

Alexey Smirnov

I ordered a window lifter for Kamaz. Even delivered ahead of schedule. Installed it, works great, everything fits in the right place. Well done guys work quickly.

Ushakov Dmitry

Advantages:

Fast processing, sociable consultants, fast delivery, convenient.

Flaws:

No

A comment:

Excellent store I ordered it and don’t regret it

Lovtsov Alexander

There are simply no words, especially about the store staff. Well done guys, they kept you informed all the way about what and how))) I didn’t regret one bit that I ordered from you)

Pugachev Alexander

Advantages:

everything is prompt.

Flaws:

undetected

A comment:

I haven’t installed it yet, but everything seems to be of good quality, even the rather thick wires.

Viktorov Artyom

Advantages:

Fast ordering and delivery

Flaws:

No

A comment:

Only the best impressions, reasonable prices and delivery on time

Vilisov Vyacheslav

Advantages:

Convenient, understandable, accessible, easy to place and receive an order!

Flaws:

Didn't find it when I first ordered

( 2 ratings, average 4 out of 5 )

Installation of power windows on a VAZ 2107

Electric windows designed for models 2104-05-07 are suitable for the front doors of the 2107 car; the easiest way to install a rack and pinion design. We install rack ESPs as follows:

• disassemble the door from the inside - remove the window handle (using a special tool or screwdriver);
• unscrew the lock release button;
• unscrew the armrest screws (three fastenings - front (top), middle and back)

• dismantle the door trim (main part);
• remove the upper part of the casing (“loaf”);
• Using a 8mm wrench, unscrew the mechanism bolts;
• unscrew the bolts of the glass guide bar, remove the guide, it will not be needed;
• we take the SME out of the door;
• unscrew the screws securing the mechanism to the glass (4 pieces - two screws on one side and two on the other);
• unscrew the window lift cable tension nut and remove the cable roller;
• completely pull out the window lifter mechanism;
• drill two holes in the door with a diameter of 6 mm (one of them is next to the hole in the door closing handle);
• We do the drilling on the same plane, and fasten the gearmotor in place of the mechanical window lifter. All screws must be taken from the kit; standard screws will not fit - they are long and will rest against the lift mechanism. If there are no short screws with the window regulators, you need to shorten the standard screws;
• We fasten the glass holders to the electric window with standard screws;
• We take out the wires from the lifts, install the buttons either on the door itself or on the central armrest, next to the gearshift lever console.

We assemble the door, and this completes the installation of the window regulator on the VAZ 2107.

Applicability on cars

Electric windows “GRANAT” are an original Russian development that has no analogues. It is simple, reliable, tested over the years on various car models.

Window lifters “GRANAT” are deservedly popular among Russian motorists. An excellent choice both for tuning and as a replacement for faulty original electric windows.

Features of the “GRANAT” window lifters: – the operating principle in which the motor reducer, together with the glass frame, moves along a fixed guide (rail) of the window lifter using a toothed shaft; – are installed in place of the guide of the original window lifter and are attached to the standard holes, while drilling additional holes and modifying the doors is not required.

Main advantages: – reliable original design, – absence of glass distortions, – absence of bending elements guarantees long-term uninterrupted operation, – window lifter is equipped with an imported gear motor, – noise level 40 – 50 dB (no louder than a running car engine), – electric window lifter during the established operating life does not require special maintenance.

Lada Granta power windows do not work

Description: Good afternoon reader, do-it-yourself car repair is a collection of all kinds of instructions (articles, videos, photo reports, questions/answers) that clearly show how to do the repair yourself. For ease of use of the etlib.ru website, all materials are divided by car brands and models, as well as into categories and types of materials. When buying a car, car enthusiasts are increasingly interested in doing their own car repairs. And so everything is in order, the length of the body of your car is 3302, width is 1245, height is 1962 mm. The wheelbase is 2933 mm. Ground clearance 112 mm. The car is equipped with a hybrid power unit. The four-cylinder engine is equipped with a system that provides engine power output. There are sixteen valves per engine. The diameter of one cylinder is 54 mm, the piston stroke is 38 mm. The engine crankshaft accelerates to 6000 rpm. Maximum torque is maintained up to 8000 rpm. Original video title: Firwat funktioneiren d' Fensterheber op Lada Granta

Release date: 05.12.2015

Quality: HD 720

Posted by admin: at the request of Dorofey

Reasoning of a car owner named Islam: Well, I won’t compare it with other manufacturers here. The car is satisfied with the price/quality ratio. It has everything for both work and travel on vacation. A spacious transformable interior. Sliding rear doors have more than once helped in tight parking so that you can move from front to back and back without any problems (IMHO) the trunk seems simply dimensionless if you fold the rear row, and for a larger volume you can also fold the middle one.

I myself work as an auto electrician, and I often have to work on the road (including over long distances), so I need tools, spare parts, and overnight accommodation.

Laughter on the topic: - How often do you drink alcohol? - More than once a week. - More specifically? - Seven.

Necessary tools for work: 1. sledgehammer; 2. Open-end wrench 32; 3.

>What to do if the power windows on Grant do not work?

Socket wrench 10; 4. scissor; 5. awl; 6. wires;

It is also necessary to check the presence of voltage at the terminals of the electric motor that operates the window lift mechanism. Often this unit fails due to lack of voltage. If there is no electricity, you need to look for an open circuit. Usually the fault should be looked for in the relay. It is also worth cleaning the contacts of the control panel. Often for this reason, the window lifter (right or left) does not work on the Lada Kalina car.

The window regulator consists of mechanics and electrics, and therefore the reasons must be sought in these parts. Let's look at where the problem may lie:

• A fuse has blown or a relay has broken.

The relay can be replaced with a jumper as in the photo. But, remember that this is a temporary option, be sure to change the relay in case of breakdown. Breakdown of the wires or the chip has come off.

Tap to the left of the button, then try pressing the button. If it works, then the contact between the wire and the button is to blame.

• Problems with the power window control unit.
• Mechanical failure within the part itself.

Troubleshooting Methods

So, when the window regulator stops working, it is necessary to find and eliminate the cause. Let's look at the whole process and steps step by step:

The first thing you need to pay attention to is the fuse. In the block it is marked as F5

You need to take it out and look. If it burns out, it should be replaced with the same one with the appropriate marking. If the fuse is intact, then the problem is in the power supply and you need to look for the problem of a broken wire. We take out the fuse and use a tester to check whether there is voltage in the on-board circuit. To do this, you need to insert the probes into the sockets and see if there is power supply. If not, then you should check the wires, relays, and control unit.