Replacing the alternator belt, replacing and lubricating the alternator belt tensioner roller VAZ 2110, 2111, 2112

04.03.2022 25 208 VAZ 2112

Author: Ivan Baranov

The belt drive allows the generator to generate electricity in the vehicle. The device can function normally provided that all its components are in good working order. This also applies to the strap. Replacing the VAZ 2112 16 valve alternator belt is not a complicated procedure that can be done in the garage. An article with detailed instructions and a video will help with this.

[Hide]

Selecting a belt manufacturer

Today, choosing a manufacturer of a particular spare part can be quite difficult due to the fairly wide selection. But if we look at the statistics of many car owners and service stations, we can conclude that the highest quality belts for driving auxiliary units are:

• BRT - Balakovo Rubber Equipment, often installed from the assembly line
• GATES - often also a factory option
• Bosch - has a fairly wide range of products, including belts, and the quality is quite high
• LUZAR
• ANDYCAR

If we consider the most trouble-free belts, then according to statistics from surveys of motorists and service station technicians, we can conclude that the highest quality ones are produced by GATES and domestic BRT.

If you use another manufacturer, or want to leave your review, you can share it in the comments below.

Replacement with power steering and air conditioning

Replacing the VAZ 2112 alternator belt with power steering

If changing the alternator belt on a car without power steering takes only ten minutes, then on the contrary, in the case of power steering or air conditioning, as on the Priora, the procedure becomes noticeably more complicated.

VAZ 21124 replacement of alternator belt with power steering

The fact is that if power steering is installed on the car, then the location of the generator is already in a different place. The power steering pump is installed in its original position. The generator itself is moved higher in this case. In addition to the fact that on cars with air conditioning and power steering, the location of the generator has been changed, the belt itself also runs on a different axis. In this case, the part first passes through the crankshaft pulley, then the tension roller, the generator shaft, the pump shaft and again the crankshaft pulley.

Note. The replacement procedure on a car with power steering is complicated by the fact that the belt rotates around the left engine mount. Thus, in order to replace the part, you should lift the engine, and only then remove the chain.

Replacing the VAZ 211240 alternator belt with steering wheel

Let's begin the replacement procedure:

• First, loosen the generator belt;
• Unscrew the engine mount.

Note. The bolt of this very support should, in theory, fall down after unscrewing, but it is possible that its head will rest against the power steering pulley. If this happens, it's okay. You will need to unscrew the power steering pulley, then unscrew 3 bolts, remove the pulley and pull out the bolt.

• We lift the engine using a bottle jack (it should be installed through the oil drain hole, and a wooden block should be placed under the edge so as not to crush the edge of the crankcase);
• Remove the crankcase protection;
• Now take out the support nut;
• We pull the generator belt through the support;
• We remove the part.

Replacing the alternator belt on a VAZ 2112 with air conditioning

Installation of a new part is carried out in the same sequence. But before buying a new belt, you should know that the part must have 6 rivets. In addition, the length of the generator belt must be exactly 1115 mm. If such a chain is not commercially available, then it is recommended to install a Priora belt with air conditioning.

Selecting a belt manufacturer

Today, choosing a manufacturer of a particular spare part can be quite difficult due to the fairly wide selection. But if we look at the statistics of many car owners and service stations, we can conclude that the highest quality belts for driving auxiliary units are:

• BRT - Balakovo Rubber Equipment, often installed from the assembly line
• GATES - often also a factory option
• Bosch - has a fairly wide range of products, including belts, and the quality is quite high
• LUZAR
• ANDYCAR

If we consider the most trouble-free belts, then according to statistics from surveys of motorists and service station technicians, we can conclude that the highest quality ones are produced by GATES and domestic BRT.

If you use another manufacturer, or want to leave your review, you can share it in the comments below.

How to tighten the Alternator Belt on a VAZ 2112

VAZ 2112 Alternator belt. Stretching and replacing the alternator belt yourself

Hello dear motorists! VAZ tenth series cars quickly spread throughout our country.

The new design, economical engine and affordable price helped expand the fans of these cars.

The designers proposed many new technical solutions that improved the performance of the cars, but some components and mechanisms were borrowed from previous models, where they had proven themselves positively.

Thus, it will not be difficult for owners of VAZ 2112 cars to stretch the alternator belt if they already belonged to earlier models of the VAZ family.

Despite widespread desire among designers to improve vehicle design, a belt drive generator remains the only feasible option for generating electricity.

Why invent something new if there are two pulleys and a belt between them. This is a simple and very reliable mechanism. Both stretching and replacing the alternator belt are easy; The drive works in any conditions.

The only negative in the process of replacing a VAZ with a 2112 is more limited in the engine compartment due to the transverse position of the engine.

VAZ 21124 Belt tension generator

The most important indicator of proper operation of the drive belt is the degree of belt tension. The engine crankshaft rotates at several thousand revolutions per minute.

In this case, sudden drops or higher speeds may occur. In such conditions, the belt drive must be very close to the working surface of the pulley, providing good traction.

How to tension the alternator belt

If you hear a squeaking sound from under the hood when it rains, or simply when there is high humidity, then most likely the problem is in the tension of the alternator belt. The problem is fixed quite simply. You need to tighten the belt more. In this article we will look at how to do it yourself.

You don’t need much of a tool, you just need a ratchet and a couple of 10 and 13 sockets.

This instruction is suitable not only for the VAZ 2110 model, but also for the VAZ 2111, VAZ 2112, since the principle and design of the alternator belt tensioner are similar.

1. First of all, we look for the generator under the hood. It is located on the left side under the hood when looking at the car from the front. I think there shouldn't be any problems with this.
2. Now you need to loosen the top nut securing the generator.
3. Now use the adjusting bolt to tighten the belt.

Step-by-step instructions for replacing a 16 valve car

It is better to carry out the replacement on an inspection groove or overpass, so that it is convenient to work under the machine.

Tools

You should prepare for the replacement procedure by preparing:

• a set of keys;
• jack;
• new consumables.

  
  New alternator belt for replacement

Stages

The replacement procedure is different for cars equipped with and without power steering. Below we will consider both options.

Replacing the alternator belt on a VAZ 2112 16 valve with installed power steering consists of the following steps:

1. First, remove the power steering fluid reservoir.
2. Then, using a key set to “13”, you need to unscrew the nut, thanks to which the generator is attached to the mounting plate.

   
   Generator drive with hydraulic booster

3. To remove the old strap, loosen the tension roller.
4. To remove the dismantled part, you need to remove the motor from the support. First you need to unscrew the cushion, and then jack up the engine until a gap appears. We take out the belt through the gap formed.
5. Assembly is carried out in reverse order.
6. There are some nuances during installation. First, the tensioner must be clamped to its extreme position.
7. Then you should tighten the belt on all the pulleys and lastly on the tension roller. This procedure is a little labor intensive.
8. After complete installation, it is necessary to tension the belt. Using the hammer handle, press and fix the tensioner.

At this stage, the difference between cars with hydraulic booster appears - they do not have an adjusting bolt. Tension adjustment is done using a tension roller.

The procedure on a car without power steering is simpler:

1. Using a “13” wrench, unscrew the generator mounting nut.
2. We loosen the belt tension by turning the adjusting bolt with a wrench to “10” counterclockwise.
3. Having moved the generator towards the cylinder block, we remove the belt.
4. Next, we put the new consumable on the drive by rotating the adjusting bolt.
5. At the next stage, we tighten the strap using the adjusting nut. We move the generator as far as possible from the cylinder block. By rotating the adjusting bolt clockwise, we increase the tension, and counterclockwise, we loosen it.
6. Then the crankshaft must be turned two turns and the tension checked again.

   
   Generator drive without power steering

This concludes the procedure for replacing the alternator belt on a VAZ 2112 16 valves. By doing it yourself, you can save on visiting a car service center. In addition, knowing how to change the alternator belt, you will feel confident on your trip, since you can always change this spare part yourself.

Loading …

In what cases is replacement necessary?

Like any consumable material, the alternator belt has a certain resource and requires constant technical inspection. According to the recommendations of the manufacturer, on a VAZ 2112, regardless of whether there are 16 valves on the engine or 8, the consumables need to be changed after 45 thousand kilometers. But these are just recommendations; it is necessary to constantly monitor the condition of the product and change it in time. Service life depends on the following factors:

• driving habits;
• operating conditions;
• product quality.

A visual inspection of the drive components should be carried out when the car has traveled a maximum of 10 thousand kilometers and before a long trip. This will make it possible to avoid unpleasant surprises along the way - a broken belt. It is recommended to carry a spare one with you in the trunk, since if it breaks, the car will no longer be able to move on its own.

The strap needs to be changed if it is torn, stretched or becomes unusable. Poor tension can be determined by a specific whistle that occurs when the engine starts. Tension plays an important role in the operation of a belt drive. If the tension is weak, the unit does not generate the amount of electricity necessary for normal operation of the car. If it is strong, the service life of the belt, drive bearings and crankshaft is reduced.

The need for replacement can be determined by inspection based on the following signs:

• the appearance of cracks and tears;
• worn surface;

Old product with worn surface

• material delamination;
• frayed edges;
• strong stretch.

It's easy to check the strap tension. It is considered normal if, with a force of 10 kg, it bends by 10-15 mm. To check it, you need to press it with your thumb approximately in the middle of the belt between the crankshaft pulley and the generator.


Tension check location (where to press)

If the deflection is greater than normal, adjust the tension or change the product.

Alternator belt replacement process

Alternator belt location

Before starting the replacement process, it must be said that the belt drives the generator, which in turn maintains a stable on-board network and also charges the battery.

So, let's get straight to the process itself:

We dismantle the “minus terminal” from the battery.

Remove the negative terminal from the battery

After unscrewing the fixing bolt, let the generator run

Remove the lower engine mount to pull out the belt.

Pull the alternator belt through the slot

Belt tension

There is a special wrench for correct tension of the alternator belt.

Product selection

The choice of alternator belt should be taken quite seriously, since its breakage will not disrupt the operation of other parts, but further movement will not be possible.

Also, it is necessary to immediately determine the quality of the product, since the work and service life will depend on this.

Original catalog number for a 16-valve engine

Original alternator belt produced by AvtoVAZ

2110-1041020 – original catalog number of the alternator belt for the 2110-2112 family of cars with a 16-valve engine. This part is produced at the AvtoVAZ plant. The average cost is 700 rubles.

Analogs

Micro-V - analogue of the alternator belt

In addition to the original product, there are a number of substitutes that are recommended for installation on a car.

As practice shows, the majority of motorists trust this category more than the original spare part.

Analogue of the original alternator belt produced by BOSCH

Causes and factors of belt life

There are quite a few reasons why the belt wear process will depend. Let's consider the main ones:

• Terms of Use.
• Climate of car use.
• Driving style.
• Product quality.

When everything is considered, it is worth considering the reasons that accompany the replacement:

1. Appearance of cracks and tears . This is the first sign that the belt is very worn and may soon break.
2. "Washability" of the inner surface . This usually happens when the generator pulley and the crankshaft are not on the same contact line, or the belt is installed crookedly.

Of course, in addition to everything, it is worth considering that you may get a defective product that does not reach its normal service life.