Front wheel bearing on Nexia - faults, article number

The bolt pattern of Daewoo Nexia rims is an important special parameter that must be taken into account when selecting and purchasing a set of new rims for this car. The second name for the parameter is also quite common - drilling. The meaning and meaning are the same, just with a different name. Knowing the data on this typical parameter is important in order to understand the method of securing the wheel rim to the chassis structure.

Daewoo Nexia at one time received positive reviews from critics and car owners and was very common on the country's roads. At the moment, the model is no longer produced.


Appearance and bolt pattern of Nexia wheels

Daewoo Nexia GM T 1999 1.5i

Generation: GM TEngine: I4, Gasoline Power: 75 hp (55 kW)Rim bolt pattern parameters

PCD (number of holes x circle diameter)4×100 mm
Center Hole Diameter (DIA)56.6 mm
FastenersM12 x 1.5
Type of fastenerBolt
TiresDiscsPCDDiaPressure
175/70 R13 82S Factory kit5Jx13 ET494×10056.61.9
185/65 R13 82T Factory kit5.5Jx13 ET494×10056.62
185/60 R14 82T Factory kit5.5Jx14ET494×10056.62
175/65 R14 81T Tuning5Jx14 ET494×10056.62
185/55 R15 81H Tuning6Jx15 ET474×10056.62.1
195/50 R15 81H Tuning6Jx15 ET474×10056.62.1
205/50 R15 82H Tuning6.5Jx15 ET454×10056.62.1
195/45 R16 79V Tuning6.5Jx16ET454×10056.62.3
215/40 R16 81V Tuning7Jx16 ET454×10056.62.3
What wheel sizes does the manufacturer recommend to install?

The Daewoo Nexia GM T 1999 1.5i is equipped with 5Jx13 ET49 rims and 175/70 R13 82S tires as standard. Where:

  • 5J - rim width in inches;
  • 13″ — tire diameter in inches;
  • ET49 - disc offset in millimeters.

The vehicle tire marking 175/70 R13 is deciphered as follows:

  • 175 — profile width (cross section of the tire) in millimeters;
  • 70 - profile height as a percentage of its width;
  • R - radial cord winding;
  • 13 - tire diameter in inches.

In addition, information about its load capacity and speed parameters can be printed on the rubber - load index and speed index. The load index is a two- or three-digit number; the speed index is indicated in Latin letters, for example 82S:

  • 82 - maximum permissible tire load 475 kg;
  • S — maximum permissible vehicle speed is 180 km/h.

Using the recommended tire sizes will help you avoid problems with handling, safety and other difficulties. What non-standard sizes can be supplied? Refer to the table; it indicates possible acceptable alternative sizes for tuning. Although there are other options that we have not described in the table. For example, wider discs of the same diameter. Or install wheels of the same width, but with a larger diameter, which is quite popular among car owners. The choice of discs is huge; you can find copies with the same parameters, but with an overhang 1-2 millimeters more or less. It is not possible to list all the options.

At the same time, the bolt pattern for all types of wheels is the same - 4x100. Thus, all disks are mounted with four bolts and the distance between them is exactly one hundred millimeters. The car's hub diameter is 56.6 mm.

How to choose original wheels

First you need to decide on seasonality. For winter, it is recommended to buy wheels one or two inches smaller than for summer.

Maximum safety while driving will be provided only by original rims. A good level of safety is also ensured by products from proven quality brands. It is not advisable to experiment with replicas or used wheels.

For Daewoo Nexia of any year of manufacture there are no problems with the selection of wheel rims of any size. Both cast and stamped products can be installed.

Parameters of alloy wheels

PCD (Pitch Circle Diameter) diameter and the number of these holes.

For example, PCD100/4 - 4 holes with a diameter of 100 mm.

Since the mounting holes are made with a significant tolerance plus in diameter, you can make a mistake in choosing a PCD if it differs from the standard one by a couple of millimeters. For example, a PCD98/4 wheel is often put on a hub with PCD100/4 (98 mm from 100 cannot be distinguished by eye). It is unacceptable. In this case, of all the nuts (or bolts), only one will be fully tightened; the remaining holes will “lead away” and the fasteners will remain untightened or tightened skewed - the fit of the wheel on the hub will be incomplete. While driving, such a wheel will “beat”, in addition, not fully tightened nuts will unscrew by themselves.

Determining PCD by distance between bolt holes

DIA - diameter of the central hole for the hub or the central hole of the disk

ET - offset (or offset) of the disk (measured in mm).

This is the distance between the longitudinal plane of symmetry of the disk and the plane of the hub. The offset can be zero (the plane of symmetry of the disk coincides with the plane of the machine hub), positive (the plane of symmetry of the disk is closer to the center of the machine than the plane of the hub - as in the figure) and negative (further). For each car model, the offset is calculated by the manufacturer to ensure optimal stability and controllability of the car, as well as the least load on the hub bearings. The Germans designate the offset ET (for example, ET30 (mm), if its value is positive, or ET-30, if negative), the French - DEPORT, manufacturers from other countries usually use the English OFFSET. The desire to install wider low-profile tires that have appeared in recent years (sometimes on larger R-size wheels) leads to the need to select a wheel with a reduced ET (i.e. the tire has become wider - you need to move it outward from the body - otherwise it will start to touch it ) . Reducing ET makes the wheel track wider; - this increases the stability of the car and gives it a stylish racing look. An excessive decrease in ET is undesirable, because may result in increased load on the wheel bearings. Increase the reach, i.e. It is usually impossible to narrow the track - the disc will rest against the brake caliper.

Extra options

To install a wheel of a different bolt pattern, special “adapters” are used - spacers

The diameter of the hub hole is measured by measuring the adapter ring. It is not necessary to run around the car with a ruler - almost all the data is indicated in the technical passport. The disc bolt pattern, for example, can be indicated on the inside of the product. However, manufacturers indicate it this way only on the spare wheel.

In most cases, the marking of stamped discs includes the manufacturer, its emblem and the date of manufacture of the product. As an option, you can contact an authorized dealer for the relevant information and find out the bolt pattern parameters for a specific make and model of the car.

This is interesting: How to find out the release date of tires

Selection of bearings for the Nexia rear hub: article number, dimensions, catalog numbers

As mentioned above, in the rear wheel hub there are two roller angular contact tapered bearings installed in a “spacer” arrangement. The nominal sizes and numbers of bearings are different.

Marking according to GOST:

  1. internal 6-7006A (according to ISO L45449/L45410);
  2. external 6-7703A (according to ISO LM11749/LM11710).

Degree of accuracy – 6. Modification – A (increased load capacity). The dimensions of the parts are presented in the table below.

To select spare parts, refer to the table below, which presents: manufacturers, costs, product configurations, catalog numbers (articles).

Table of recommended spare parts manufacturers

No.ManufacturerCatalog numberPrice 2022, rub.Equipment
screwStuffing boxCotter pinWasher
1VPZ Volzhsky Bearing Plant RussiaSet of: 6-7006A 6-7703A210 190
2FAG Germany Analog713 6445 10790++
3SWAG Germany Analog440850001630++++
4NTN-SNR France AnalogR153.07830++

WHEEL BEARING SIZE TABLE

CharacteristicUnitValue according to GOST (TU)
6-7703A (external)6-7006A (internal)
Hole diametermm17,4629,0
External diametermm39,87850,29
Installation heightmm13,84314,22
Dynamic load capacitykH23,426,0
Static load capacitykH23,732,0
Speed ​​min-maxrpm9000-130007000-10500
Kit axial clearancemm0,03-0,13
Steel typeSHH-15
Hardness of steel and rollersH.R.C.61-65
Contact anglehail10-18
TorqueN*M2,5
Ring roughnessRa0.32
WeightG.0,080,11

Daewoo Nexia wheel rim pattern: parameters

Alloy wheels are beautiful, impressive and original. This is not to say that this is very practical on our roads, although many owners of mass-produced cars are thinking about investing a tidy sum in alloy wheels for their one and only. It’s tempting, but before that you need to weigh and calculate everything. The wheel bolt pattern for our Daewoo Nexia is the number one issue in this case. First the bolt pattern, and then the design.

What is disc bolt pattern?

The bolt pattern determines whether the disc can be installed on a car.

Each wheel rim is characterized by a mass of geometric values, which many have no idea about. In vain, because it is absolutely not enough to know the number of holes for bolts and the diameter of the disk. A bunch of other parameters affect both safety and the service life of the car’s chassis, suspension and tires. And here every fraction of a millimeter is important.

Disc bolt pattern is a set of parameters that are arranged into a single geometric model that is either suitable for a particular car or unacceptable for use on it.


HOW TO FIND OUT THE BOLTS OF WHEELS ON A CAR.

Basic parameters of the wheel rim.

  1. The seat width of the wheel is measured in inches.
  2. Landing diameter. Also measured in inches.
  3. The distance from the mounting surface of the disk to the center of the tire. Designated ET.
  4. The number of holes for fasteners and the diameter at which their centers are located. Most often, this parameter is called a bolt pattern, but this is not entirely true. The parameter is designated as Pitch Circle Diameter or PCD.
  5. The diameter of the disk mounting hole, the one that fits on the hub. It is designated DIA and measured in millimeters.

The PCD parameter depends on the distance between the centers of adjacent holes and on their number.

What kind of chatter does the Daewoo Nexia have?

To understand this whole geometric compote, let’s look at examples with disks for Nexia. As a rule, Nexias of different years of production are equipped with wheels with a diameter of 13 and 14 inches. Here are their parameters:

  • 13/5J PCD 4×100 ET 49 DIA 56.6
  • 13/5.5J PCD 4×100 ET 49 DIA 56.6;
  • 14/5.5J PCD 4×100 ET 49 DIA 56.6.

Stamped standard 13-inch wheel for Nexia.

Now the markings of a standard Nexia disk become clear:

  1. 13 and 14 are the diameter of the disc, measured in inches.
  2. 5.5J (5J) or simply 5.5(5) is the width of the rim in inches.
  3. PCD 4x100 - four holes, the centers of which are located along a diameter of 100 mm.
  4. ET 49 - the distance from the mounting surface of the disk to the center of the tire is 49 millimeters.
  5. The landing diameter of the hub hole is 56.6 mm.

A set of 14-inch wheels for the Daewoo Nexia with a standard bolt pattern.

Alternative options

This is a standard bolt pattern for Nexia with 13 and 14 discs. If desired, you can also install 15-inch wheels if their parameters are as follows: 15/6.0J PCD 4×100 ET 40 DIA 56.6.

It is clear that the ride on such wheels will not be comfortable, but it looks very impressive. Note that in any case the PCD and DIA parameters remain unchanged. The issue with offset is complicated, since the parameter cannot but take into account the width of the disk. If the offset is too large with a large diameter and large width, the rubber will inevitably reach the fender liners and wheel arches. And vice versa - if the offset is insufficient, but the wheels are wide and large in diameter, when turning we will scratch the tires against the suspension parts.

Proven replacements

Alloy wheel for Daewoo Nexia GM12 (copy of the original disk).

Proven options for replacing factory disks:

  • 6Jx14 4x100 ET45;
  • 6Jx15 4x100 ET45;
  • 5Jx15 4x100 ET45;
  • 5Jx16 4x100 ET45;
  • 7Jx15 4x100 ET45;
  • 7Jx16 4x100 ET45.

Naturally, the landing hub diameter DIA remains stable for everyone - ET 56.6.

Theoretically, it is possible to install disks of a different bolt pattern using adapters, but is it worth doing?

How is the wheel bolt pattern measured on Daewoo cars?

When you have to select and purchase new wheels for the Nexia, you need to know the drilling parameters on the car in advance. The most accessible way to determine it for any car brand is to use a special table that can be found on the Internet. It contains, depending on the year of manufacture and engine size, all the necessary parameters and dimensions.

The third method is the least accurate and most labor-intensive. In this case, you can independently measure all the required dimensions. To determine the bolt pattern depending on the number of fasteners, you will need to apply the following formulas:

  • B=A×1.155 - used for three holes;
  • B=A×1.414 - calculated for four holes;
  • B=A×1.701 - for five holes.

Having received the value of the required value, you can easily calculate the required diameter size, which is designated as B.


Daewoo Nexia car with alloy wheels

Daewoo Nexia GM T 2005 1.5i

Generation: GM TEngine: I4, Gasoline Power: 84 hp
(62 kW) Wheel bolt pattern parameters

PCD (number of holes x circle diameter)4×100 mm
Center Hole Diameter (DIA)56.6 mm
FastenersM12 x 1.5
Type of fastenerBolt
TiresDiscsPCDDiaPressure
185/60 R14 82T Factory kit5.5Jx14ET494×10056.62
205/55 R14 82H Tuning6Jx14 ET474×10056.62.1
185/55 R15 81H Tuning5.5Jx15 ET494×10056.62.1
195/50 R15 81H Tuning6Jx15 ET474×10056.62.1
205/50 R15 82H Tuning6.5Jx15 ET454×10056.62.1
185/45 R16 77V Tuning6Jx16 ET474×10056.62
195/45 R16 79V Tuning6.5Jx16ET454×10056.62.3
215/40 R16 81V Tuning7Jx16 ET454×10056.62.3
What wheel sizes does the manufacturer recommend to install?

The Daewoo Nexia GM T 2005 1.5i is equipped with 5.5Jx14 ET49 rims assembled with 185/60 R14 82T tires as standard. Where:

  • 5.5J - rim width in inches;
  • 14″ — tire diameter in inches;
  • ET49 - disc offset in millimeters.

The vehicle tire marking 185/60 R14 is deciphered as follows:

  • 185 — profile width (cross section of the tire) in millimeters;
  • 60 - profile height as a percentage of its width;
  • R - radial cord winding;
  • 14 is the tire diameter in inches.

In addition, information about its load capacity and speed parameters can be printed on the rubber - load index and speed index. The load index is a two- or three-digit number; the speed index is indicated in Latin letters, for example 82T:

  • 82 - maximum permissible tire load 475 kg;
  • T — maximum permissible vehicle speed is 190 km/h.

Using the recommended tire sizes will help you avoid problems with handling, safety and other difficulties. What non-standard sizes can be supplied? Refer to the table; it indicates possible acceptable alternative sizes for tuning. Although there are other options that we have not described in the table. For example, wider discs of the same diameter. Or install wheels of the same width, but with a larger diameter, which is quite popular among car owners. The choice of discs is huge; you can find copies with the same parameters, but with an overhang 1-2 millimeters more or less. It is not possible to list all the options.

At the same time, the bolt pattern for all types of wheels is the same - 4x100. Thus, all disks are mounted with four bolts and the distance between them is exactly one hundred millimeters. The car's hub diameter is 56.6 mm.

General background information

Ranges of possible values ​​for tires and wheels of Daewoo Nexia 2008.

Tires

Diameter14″–16″
Width (mm)185–215
Profile (%)40–60
The smallest size185/60 R14
The biggest size215/40 R16

Wheel disks

Diameter14″–16″
Width (inches)5.5–7
Reach (mm)45–49
Drills4×100
Expert advice

When choosing tires for a car, you must first follow the manufacturer's instructions. Ask yourself a few questions.

  • On what roads will the car be primarily used?
  • Do you need increased cross-country ability?
  • How much of the route will be city roads and how much will be highways?
  • Will the vehicle carry heavy loads?

The answers to these and similar questions will help determine which tire parameters you need to pay special attention to.

How to choose the right wheels for Daewoo Nexia 2008?
  • Stamped (economical price category) - made from a sheet of iron by stamping on a press.
  • Light alloy - manufactured by casting (more reliable than stamped ones).
  • Forged (the highest quality and more expensive than the previous ones) - made from light alloys by stamping at high temperatures.

The choice depends on financial capabilities. However, it should be borne in mind that the quality of the road surface on which you have to drive every day must also be taken into account.

So, if it gets into a hole, a stamped disk will bend and will not cause harm to the tire, but a forged or cast one can cut it. There is a possibility that the cast disc may burst or crack.

It should also be noted that repairing “stamping” wheels is cheaper than repairing cast or forged wheels. But wheels with high-quality cast and forged disks kill the suspension less, because lighter and have more perfect geometry (better balanced).

The same wheels may or may not rub with tires on the same car - wheel alignment adjustment will help here.

Wheels for "Matiz"

When calculating the recommended tire size, the vehicle manufacturer is guided by all technical characteristics. This list includes weight, acceleration dynamics, maximum speed, tendency to sideways skids and other parameters. When installing the recommended standard size, the car owner will be able to ensure the most comfortable and safe ride in any difficult situations.

For Daewoo Matiz, the “Car Operation Manual” provides 2 types of standard sizes:

  • 155/65 R13;
  • 145/70 R13.

The first option is found most often in the Matiz configuration. Explanation:

  • 155 - measured in millimeters, indicates the width of the product. Determined by the distance between the outer sides of the sidewalls of the inflated tire.
  • 65 - means profile height - percentage. Accordingly, the profile height is 65% of the width (155 mm).
  • R is not a radius, as many people believe, but just a designation of how the cord threads are located in the tire carcass. The designation “R” is a tire with a radial cord.
  • 13 - seat diameter of the rim (inner diameter of the tire), measured in inches (1 inch = 25.4 mm).

Important!

The official manufacturer recommends using summer and winter wheels on Matiz of the above sizes.

Wheel size for Daewoo Matiz

It is worth noting the fact that when performing calculations for wheel sizes, the manufacturer takes into account the features and performance characteristics of the Daewoo Matiz car:

  • starting acceleration;
  • maximum speed;
  • dynamic indicators;
  • tendency to skid;
  • controllability;
  • braking.

As a result, when using wheel sizes recommended by the manufacturer, the car owner is provided with a comfortable and safe ride, regardless of weather conditions and the route.

According to the vehicle operating manual for Matiz, it is recommended to use two sizes of tires:

  • 145/70/R13;
  • 155/65/R13.

Now let’s take a closer look and analyze one of the specified standard sizes:

  1. The first number 145 indicates the profile width of the tire in mm. That is, this is the distance between the sides of the tire of the inflated wheel.
  2. The second number 70 shows the profile height as a percentage of the tire. Thus, the first standard size indicates that the profile height is 70% of the tire width of 145 mm.
  3. The Latin letter R denotes the radius of the wheel. According to car enthusiasts, this letter indicates the location of the cord threads in the tire structure. Thus, the tire has a radial cord. At this point, almost all types of tires have a radial design.
  4. The last number 13 shows the fit of the disc rim, that is, the internal diameter of the rubber. This indicator is measured in inches.

Selecting wheels for Matiz

Korean manufacturers recommend using winter and summer tires with the specified sizes. Advice from car manufacturers: using other sizes not specified in the operating instructions may result in damage to the body.

In addition, it is not recommended to install tires with non-standard sizes if the vehicle owner uses 175/60/R13 tires instead of the standard 155/65/R13 or 145/70/R13. In this case, it is necessary to completely replace one of the steering system mechanisms.

Immediately before installation, you must consult with Deo auto center dealers. They can make recommendations for using factory spec wheels.

However, there are also non-standard tire sizes that can be used for Matiz vehicles.

According to reviews from car enthusiasts and maintenance specialists, when using tire sizes that do not correspond to factory parameters, minimal contact with the body is observed. Basically, the wheel can touch the fender liner only when the steering wheel is turned extremely.

Tire size 155/70/R13 is suitable for standard wheels. It can be used without fender liners or with them, since friction on the body is minimal.

For example, during the Daewoo repair process, maintenance specialists do not pay attention to the fact that the owner uses non-standard tires, because they know that there are no defects or violations.

Tires with sizes 165/70R/13 practically cannot be used on Matiz with fender liners. If you install a wheel with such a tire, then 1/4 of it will touch the fender liner and deform it when driving.

After removing these parts, the wheels will touch the arch during maximum turns, but only in situations where the car is driven up a hill or curb. If you do not perform such turns, then tires can be used as an alternative option.

Tires with dimensions 165/65/R13 are suitable for Matiz, since friction with the vehicle body is minimal.

Non-standard wheels can cause problems when operating the Daewoo Matiz:

  • the total weight of the vehicle increases;
  • high fuel consumption;
  • additional loads on the suspension and transmission;
  • load on the operation of the power unit;
  • change in braking distance.

The main differences between stamped and cast wheels for Matiz

Before releasing their own products for sale, engineers conduct numerous studies.

The laboratory tests the strength of the product, reaction to impacts, endurance, test drive. Taking into account all these details, the manufacturer of Daewoo Matiz guarantees car owners of this brand a high level of safety.

You might be interested in this: Wheel rims R16

The production process is carried out using modern equipment. Our specialists regularly implement the latest innovative technologies to achieve maximum results. A high-quality anti-corrosion protective coating is applied to the structure. Thus, alloy wheels for the Daewoo Matiz are completely protected from high levels of reagents.

Alloy wheels R13 on Matiz have an original design. The list of products is very diverse; a wide range of models and standard sizes allows the design to be used on cars of almost all brands. Alloy wheels for the Daewoo Matiz reduce fuel consumption.

Important!

Stamped steel products provide reliability, high quality, and strength.

Designation and marking of wheels

The main difference between wheel bolt pattern is the marking of Daewoo Nexia wheels. It is the same for both cast and stamped models. In most cases, it is marked as follows: 5.5Jx13 4/100 ET 49 for steel wheels, 5.5x14 4/100 ET 49, steel for Euro III, IV; 5.5Jx14 GLE. It is quite easy to understand such inscriptions.

The width of the disk is indicated by the very first character - in this case it is the number 5.5. Diameter – numbers 13 and 14. Both parameters, respectively, are measured in inches. The amount of offset, or overhang, of the product is designated “ET 49”. And here's a chat about

This is what you should pay special attention to: the number of bolts is indicated by the first digit, the diameter of the fasteners – by the second digit

The “ET30” value, which has already been mentioned, denotes the offset indicator, in this case equal to 30. Simply put, thirty millimeters is the distance between the center of the disk width and its mating plane. The mating plane is understood as that part of the product that is pressed directly against the hub.

The disk markings look like this

Bolt pattern on Daewoo Nexia

The bolt pattern determines whether the disc can be installed on a car.

Each wheel rim is characterized by a mass of geometric values, which many have no idea about. In vain, because it is absolutely not enough to know the number of holes for bolts and the diameter of the disk. A bunch of other parameters affect both safety and the service life of the car’s chassis, suspension and tires. And here every fraction of a millimeter is important.

Disc bolt pattern is a set of parameters that are arranged into a single geometric model that is either suitable for a particular car or unacceptable for use on it.

Basic parameters of the wheel rim.

  1. The seat width of the wheel is measured in inches.
  2. Landing diameter. Also measured in inches.
  3. The distance from the mounting surface of the disk to the center of the tire. Designated ET.
  4. The number of holes for fasteners and the diameter at which their centers are located. Most often, this parameter is called a bolt pattern, but this is not entirely true. The parameter is designated as Pitch Circle Diameter or PCD.
  5. The diameter of the disk mounting hole, the one that fits on the hub. It is designated DIA and measured in millimeters.

The PCD parameter depends on the distance between the centers of adjacent holes and on their number.

What kind of chatter does the Daewoo Nexia have?

To understand this whole geometric compote, let’s look at examples with disks for Nexia. As a rule, Nexias of different years of production are equipped with wheels with a diameter of 13 and 14 inches. Here are their parameters:

  • 13/5J PCD 4×100 ET 49 DIA 56.6
  • 13/5.5J PCD 4×100 ET 49 DIA 56.6;
  • 14/5.5J PCD 4×100 ET 49 DIA 56.6.

Stamped standard 13-inch wheel for Nexia.

Now the markings of a standard Nexia disk become clear:

  1. 13 and 14 are the diameter of the disc, measured in inches.
  2. 5.5J (5J) or simply 5.5(5) is the width of the rim in inches.
  3. PCD 4x100 - four holes, the centers of which are located along a diameter of 100 mm.
  4. ET 49 - the distance from the mounting surface of the disk to the center of the tire is 49 millimeters.
  5. The landing diameter of the hub hole is 56.6 mm.

Bearing dimensions on Nexia

There are two types of wheel bearings installed on the Nexia, people often get confused, but here’s a hint for you on how to choose the right wheel bearing.

Nexia SOHC has 8 valve engine options, they have a small bearing and a standard wheel size of R13.

For example, Nexias with a 1.5 and 8 valve engine require a small bearing. On a Nexia with a DOHC 1.6 16 valve engine, they install a larger bearing and, accordingly, the tires are size R14.

R13 SOHC bearing dimensions: 64mm x34mm x 37mm

R14 DOHC Bearing Dimensions: 72mm x 39mm x 37mm

Remember this once and for all. But there are times when there is a different bearing, this is due to the fact that there is a different hub, this happens if you bought a Nexia secondhand and did not know that the owner changed the suspension. But what to buy, which bearing to choose?

A good bearing will cost 1000 rubles, but not all. They recommend installing SKF - according to reviews, they have the most durable bearings. Nowadays, bearings are usually supplied with two locking rings; sometimes manufacturers include not only locking rings, but also a hub nut and a hub nut retainer.

R13 SOHC code: 94535246

R14 DOHC article number: 94535254

If the article was useful, share the article with a friend

I need the size of the front wheel bearing, there are 2 sizes according to my VIN code. 64x34x37 and 72x39x37

How to determine it yourself

It is clear that if you buy rims from an official supplier, then there should be no problems. Just look at the specified parameters, and they should correspond to reality. Although, of course, it wouldn’t hurt to check.

But where you definitely can’t do without checking is when buying from someone else. Here you need to carefully make sure that the parameters are exactly as the seller says. Even if he is a decent person and tells the truth, this does not mean that he is not mistaken.

Here's how to find out what wheel bolt pattern is on a Daewoo Matiz:

  1. First you need to prepare the necessary tools. Ideally, this is a caliper, but in a pinch, you can get by with a ruler. This is necessary because it is impossible to measure the diameter of a circle by eye.
  2. Then you need to take all the necessary measurements. If the seller is decent and smart enough, he will not interfere with the process.
  3. It is advisable to take measurements on Matiz fasteners. Only in this case will it be possible to fully ensure that the rims will fit exactly.

Some may wonder why measure fasteners. No matter how popular and respected a particular brand is in the automotive industry, there is always a risk of mistakes and defects. And therefore, if a person is already engaged in independent replacement, he should take this into account and play it safe.

Some recommend inserting the obtained data on the bolt pattern of wheel rims on Daewoo Matiz into special formulas. This should show that the wheels will fit the car exactly. It is worth noting, however, that it is better to take original products for this model.

Front wheel bearing Daewoo Nexia: features of choice

>Daewoo Nexia front wheel bearing size

The actual size of the front wheel bearing of the Daewoo Nexia depends on the type of wheel. Models before 2008 may have a 13th diameter, in which case the size will be 64*34*37.

For the 14th diameter, the wheel bearing has dimensions of 39*72*37 mm. This information can also be obtained from dealers or managers of a certified service station. The numbers in the catalog cannot change, but new ones may appear, since the assortment is constantly updated.

Daewoo Nexia front wheel bearing number

Catalog numbers of major manufacturers:

Price of front wheel bearing Daewoo Nexia

Products produced by the Volzhsky plant with the VPZ marking will cost from 450 rubles. (cat. no. 537708). Also a good manufacturer is FAG, a world leader in their manufacture (catalog no. 803646). They are about three times more expensive than domestic ones due to the higher quality materials and technologies used.

Answers (3)

Follow the answers to this question

  • Nexy's bolt pattern is 4×100
    freelance Automotive enthusiast

    07/22/2013 at 16:53

  • bolt pattern 4 to 100, CO - 56.6 here are the parameters for different types of wheels R13 - 13 / 5.5J PCD 4×100 ET 49 CO 56.6 R14 - 14 / 5.5J PCD 4×100 ET 49 CO 56.6 R15 - 15 / 6.0J PCD 4 ×100 ET 40 CO 56.6 - yes, you can install 15s, I had such a Nexia at 15, very inconvenient, but beautiful)
    Dmitry Nikolaev Newbie

    28.11.2013 at 17:10

  • Hub diameter - 56.6 mm
    Factory tire size:

    175/65 R14 185/60 R14 - these were the ones on my Nexia.

    Before the pre-restyling model, tires of sizes 175/70R13, 185/65R13 and 185/60R14 were also installed

    wheelman I know everything about tires and wheels

    11/19/2017 at 22:32

Similar questions

Peter

Daewoo Nexia

What is disc bolt pattern?

The bolt pattern determines whether the disc can be installed on a car.

Each wheel rim is characterized by a mass of geometric values, which many have no idea about. In vain, because it is absolutely not enough to know the number of holes for bolts and the diameter of the disk. A bunch of other parameters affect both safety and the service life of the car’s chassis, suspension and tires. And here every fraction of a millimeter is important.

Basic parameters of the wheel rim.

  1. The seat width of the wheel is measured in inches.
  2. Landing diameter. Also measured in inches.
  3. The distance from the mounting surface of the disk to the center of the tire. Designated ET.
  4. The number of holes for fasteners and the diameter at which their centers are located. Most often, this parameter is called a bolt pattern, but this is not entirely true. The parameter is designated as Pitch Circle Diameter or PCD.
  5. The diameter of the disk mounting hole, the one that fits on the hub. It is designated DIA and measured in millimeters.

The PCD parameter depends on the distance between the centers of adjacent holes and on their number.

What kind of chatter does the Daewoo Nexia have?

To understand this whole geometric compote, let’s look at examples with disks for Nexia. As a rule, Nexias of different years of production are equipped with wheels with a diameter of 13 and 14 inches. Here are their parameters:

  • 13/5J PCD 4×100 ET 49 DIA 56.6
  • 13/5.5J PCD 4×100 ET 49 DIA 56.6;
  • 14/5.5J PCD 4×100 ET 49 DIA 56.6.

Stamped standard 13-inch wheel for Nexia.

Now the markings of a standard Nexia disk become clear:

  1. 13 and 14 are the diameter of the disc, measured in inches.
  2. 5.5J (5J) or simply 5.5(5) is the width of the rim in inches.
  3. PCD 4x100 - four holes, the centers of which are located along a diameter of 100 mm.
  4. ET 49 - the distance from the mounting surface of the disk to the center of the tire is 49 millimeters.
  5. The landing diameter of the hub hole is 56.6 mm.

A set of 14-inch wheels for the Daewoo Nexia with a standard bolt pattern.

Alternative options

This is a standard bolt pattern for Nexia with 13 and 14 discs. If desired, you can also install 15-inch wheels if their parameters are as follows: 15/6.0J PCD 4×100 ET 40 DIA 56.6.

It is clear that the ride on such wheels will not be comfortable, but it looks very impressive. Note that in any case the PCD and DIA parameters remain unchanged. The issue with offset is complicated, since the parameter cannot but take into account the width of the disk. If the offset is too large with a large diameter and large width, the rubber will inevitably reach the fender liners and wheel arches. And vice versa - if the offset is insufficient, but the wheels are wide and large in diameter, when turning we will scratch the tires against the suspension parts.

Proven replacements

Alloy wheel for Daewoo Nexia GM12 (copy of the original disk).

Proven options for replacing factory disks:

  • 6Jx14 4x100 ET45;
  • 6Jx15 4x100 ET45;
  • 5Jx15 4x100 ET45;
  • 5Jx16 4x100 ET45;
  • 7Jx15 4x100 ET45;
  • 7Jx16 4x100 ET45.

Theoretically, it is possible to install disks of a different bolt pattern using adapters, but is it worth doing?

Wheel bearing diagnostics

Ideally, in order not to waste time on diagnostics, it is advisable to change the bearing in pairs, since identical companies make the same noise; if one bearing hums, then soon the second bearing will hum. But if you still want to find out which side the hum is coming from, then you need to listen carefully:

When turning right, the hum will be stronger, the left side of the car is loaded, and the faulty bearing will begin to hum. When turning right, the left bearing hums. And accordingly, on the contrary, when turning left, the noise from the right bearing increases . But in my practice there was a case when everything was the other way around: the left bearing was broken, and when it was loaded, the sound disappeared. But there was a huge play, so to confirm the diagnosis, shake the wheel in different directions with your foot, as if checking the tire pressure. If there is play, it is probably a faulty wheel bearing or a broken ball bearing.

So, which bearing to buy for Nexia?

Characteristics and parameters

To select high-quality wheels for the Daewoo Nexia, you need to know such parameters as the bolt pattern and the dimensions of the mounting holes. Having such information, there will be no problems with selection and purchase.

Before purchasing, it is also advisable to consult with the seller about the chosen model. It is possible that some wheels do not perform well during operation.

The larger the wheel size installed on the car, the better the quality of control and behavior on the road. But you should also take into account the increased wear rate of suspension parts and the decreased level of driving comfort. The larger the size of the wheels themselves, the lower the profile of the tires themselves must be chosen. This will also not have the best effect on the wear of the wheels themselves, since the level of load on them will increase.

Signs of a bad wheel bearing

Signs of a wheel bearing failure on a Nexia are the same as on any other car. The wheel bearing begins to whine slightly at speed, and the more you drive with a broken wheel bearing, the louder the noise will become. For example, driving with a faulty (humming) wheel bearing threatens to increase fuel consumption, an unpleasant hum throughout the body, but also jamming. The bearing can jam at any second, imagine what will happen if one wheel locks at 100 km per hour?

So, a strong hum, vibration in the body, usually from the front side, and wheel play - these are the main signs of a faulty wheel bearing, at least this was the case in my Nexia. How do you know which side the wheel bearing needs to be replaced?

Characteristics and parameters

To select high-quality wheels for the Daewoo Nexia, you need to know such parameters as the bolt pattern and the dimensions of the mounting holes. Having such information, there will be no problems with selection and purchase.

Before purchasing, it is also advisable to consult with the seller about the chosen model. It is possible that some wheels do not perform well during operation.

Important!

When choosing rims, you need to consider whether tires of similar sizes are common.

The larger the wheel size installed on the car, the better the quality of control and behavior on the road. But you should also take into account the increased wear rate of suspension parts and the decreased level of driving comfort. The larger the size of the wheels themselves, the lower the profile of the tires themselves must be chosen. This will also not have the best effect on the wear of the wheels themselves, since the level of load on them will increase.

For the winter season, 14-inch wheels are most suitable for the Daewoo Nexia. They will give the car optimal performance in poor operating conditions and on rough roads.

In summer, it is recommended to install wheels with a radius of 15 inches for maximum traction and best handling.

Tire parameters for Daewoo Nexia 2011:

  • diameter (measured in inches) - from 14 to 16;
  • width (millimeters) - from 185 to 215;
  • tire profile (%): from 40 to 60;
  • minimum tire size - 185/60 R14;
  • maximum tire size is 215/40 R16.

You might be interested in 17-radius alloy wheels

Disc parameters for Daewoo Nexia 2011:

  • drilling (often referred to as bolting) - 4×100;
  • diameter (measured in inches) - from 14 to 16;
  • width (inches) - from 5.5 to 7;
  • wheel offset ET (millimeters) - from 45 to 49;
  • diameter of the central hole (DIA) - 56.6.


Disk parameters for Nexia

What are they made of?

The easiest way to buy cast alloy wheels in Moscow. They are made from a special alloy based on aluminum and additional additives. The product is poured under high pressure, polished, and brought to high aesthetic standards. If you follow the rules for their use, such wheels will last for several seasons of active daily driving on not the best roads. The price of such disks depends on various parameters. But any owner of Daewoo Nexia will find a favorable price for themselves.

There are also forged wheels. They are much more expensive because they are made using a different technology. At the same time, their durability is much higher. But often they need to be ordered separately. They are quite difficult to find in mass sales.

The main differences between stamped and cast wheels for Matiz


The difference between stamped and cast car wheels Stamped designs have gained popularity not only because of their affordable cost, but also for their qualities.
Before releasing their own products for sale, engineers conduct numerous studies.

The laboratory tests the strength of the product, reaction to impacts, endurance, test drive. Taking into account all these details, the manufacturer of Daewoo Matiz guarantees car owners of this brand a high level of safety.

You might be interested in this Australian manufacturer of PDV discs

The production process is carried out using modern equipment. Our specialists regularly implement the latest innovative technologies to achieve maximum results. A high-quality anti-corrosion protective coating is applied to the structure. Thus, alloy wheels for the Daewoo Matiz are completely protected from high levels of reagents.

Alloy wheels R13 on Matiz have an original design. The list of products is very diverse; a wide range of models and standard sizes allows the design to be used on cars of almost all brands. Alloy wheels for the Daewoo Matiz reduce fuel consumption.

Important!

Stamped steel products provide reliability, high quality, and strength.

Daewoo Nexia GM T Restailing 2012 1.6i

Generation: GM T Restailing Engine: I4, Flex-Fuel Power: 109 hp
(80 kW) Wheel bolt pattern parameters

PCD (number of holes x circle diameter)4×100 mm
Center Hole Diameter (DIA)56.6 mm
FastenersM12 x 1.5
Type of fastenerBolt
TiresDiscsPCDDiaPressure
185/60 R14 82T Factory kit5.5Jx14ET494×10056.62
195/55 R14 80H Tuning6Jx14 ET474×10056.62.1
205/55 R14 82H Tuning6Jx14 ET474×10056.62.1
195/50 R15 80H Tuning6Jx15 ET474×10056.62.1
205/50 R15 81H Tuning6.5Jx15 ET454×10056.62.1
215/40 R16 81V Tuning7Jx16 ET454×10056.62.3
What wheel sizes does the manufacturer recommend to install?

The Daewoo Nexia GM T Restailing 2012 1.6i is equipped with 5.5Jx14 ET49 rims assembled with 185/60 R14 82T tires as standard. Where:

  • 5.5J - rim width in inches;
  • 14″ — tire diameter in inches;
  • ET49 - disc offset in millimeters.

The vehicle tire marking 185/60 R14 is deciphered as follows:

  • 185 — profile width (cross section of the tire) in millimeters;
  • 60 - profile height as a percentage of its width;
  • R - radial cord winding;
  • 14 is the tire diameter in inches.

In addition, information about its load capacity and speed parameters can be printed on the rubber - load index and speed index. The load index is a two- or three-digit number; the speed index is indicated in Latin letters, for example 82T:

  • 82 - maximum permissible tire load 475 kg;
  • T — maximum permissible vehicle speed is 190 km/h.

Using the recommended tire sizes will help you avoid problems with handling, safety and other difficulties. What non-standard sizes can be supplied? Refer to the table; it indicates possible acceptable alternative sizes for tuning. Although there are other options that we have not described in the table. For example, wider discs of the same diameter. Or install wheels of the same width, but with a larger diameter, which is quite popular among car owners. The choice of discs is huge; you can find copies with the same parameters, but with an overhang 1-2 millimeters more or less. It is not possible to list all the options.

At the same time, the bolt pattern for all types of wheels is the same - 4x100. Thus, all disks are mounted with four bolts and the distance between them is exactly one hundred millimeters. The car's hub diameter is 56.6 mm.

Discs

Selecting and purchasing high-quality wheels for the Daewoo Nexia is not difficult. Many brands on the market are suitable for this car model. You can choose products to suit every taste and budget. The most common are stamped wheels, but cast ones can also be purchased if desired. Products of any design, color and shape are presented.


Daewoo Nexia, stamped steel wheels

The size of Daewoo Nexia wheels from the factory can be in three designs, with radii from 13 to 15 inches. But if necessary, it is common among tuning enthusiasts to install even R16 wheels. For this, special spacers are used.

Daewoo Nexia has been produced in various countries since 1994, and since 2016 it has been changed to the Ravon Nexia brand. Regardless of the country of manufacture, the recommended wheel and mount sizes remained the same.

Thanks to factory unification and ease of selection of wheels, you can choose from original, used and cast products. All these options have their advantages and disadvantages. To make the right choice, you need to consider them all.

Replacing the wheel bearing of Daewoo Nexia: how to understand that it is required?

To find out whether the front wheel bearing of the Daewoo Nexia requires repair and replacement, you need to do the following:

  1. Raise the desired side with a jack;
  2. Hold the wheel with both hands and check the play.

If there is free play, the problem must be corrected. In the factory, everything is securely fixed with rings on both sides in the grooves of the body and therefore the hub must be stationary. Another sign of the need for replacement is that the hum disappears/appears when turning. For example, if the noise disappears for a short time when turning right, then the problem is on the left side, and vice versa.

Rating
( 2 ratings, average 4.5 out of 5 )
Did you like the article? Share with friends:
For any suggestions regarding the site: [email protected]
Для любых предложений по сайту: [email protected]