How to change the oil and filter in the engine of a VAZ-2115 car

Print this article Font size 16

Actually, why is this crankcase gasket necessary? The “tens” engine includes many units, components and systems. The crankcase is the engine body and plays a vital role. After all, it is it that contains all the main elements of the engine inside itself and provides them with the necessary protection and allows oil to circulate.

The crankcase includes two collapsible elements, between which the gasket is located. It is responsible for sealing the connection between two crankcase elements and prevents oil from leaking out of the system, which, by the way, is under high pressure.

Replacing the engine sump gasket for VAZ 2108, 2109, 21099

The pan gasket on the engines of VAZ 2108, 2109, 21099 cars and their modifications has to be changed in case of damage (oil leakage under the gasket), during engine repairs (replacing pistons, rings, etc.).
Necessary tools, accessories and spare parts Wrench “10” (socket or head with wrench)

New engine pan gasket

Solvent (gasoline, diesel fuel, etc.), rags

We install the car on a viewing hole, overpass or lift

Removing the engine compartment protection sheet

Removing engine mudguards

Removing the lower clutch housing cover

Drain the engine oil from the sump

Features of replacing the engine pan gasket VAZ 2108, 2109, 21099

Unscrew the pallet mounting bolts

We use the key to “10”. There are 16 bolts in total.

Removing the engine sump

We move it forward a little to free it from engagement with the oil pump intake and remove it down.

Removing the old pan gasket

Cleaning the tray from dirt

We clean the pallet itself and its mating surface under the gasket with a rag soaked in solvent.

Clean the mating surface of the block for the gasket

We use rags and solvent. The main condition for installing a new pan gasket is that the parts in contact with it are clean and dry.

Installing a new gasket

Place a new gasket on the mating surface of the pallet.

Installing the sump on the engine

Carefully press the pan against the engine so as not to displace the gasket. First, we engage it with the oil intake, moving it slightly forward. Place several bolts along the edges of the pallet. Screw in the remaining bolts. Lightly tighten them first. We make the final tightening of the bolts in several passes from the middle to the edges of the pallet so that the gasket lies evenly. The final tightening torque is within 10 N.m.

Notes and additions

For installation, it is better to use a silicone gasket rather than a cork gasket, as it is more reliable and has a longer service life.

Special pressure shaped washers are installed under the heads of the pallet bolts.

More articles on engines of VAZ 2108, 2109, 21099 cars

Instructions for removing, cleaning and replacing the engine sump on Lanos and Chance 1.5

Before starting work on removing the oil pan on Lanos, you will need to first purchase a sealing gasket, oil, filter and sealant. Which oil to choose and how to replace it on Lanos is described in detail in this material. The article number of the sealing gasket for Lanos and Chance 1.5 cars is 90409693

. However, do not rush to buy it, since the likelihood that you will be able to install the pallet in place with it is very low. We use sealant as a gasket.

Let's proceed to directly removing the crankcase cover Lanos and Chance 1.5:

1. First, the car must be installed on an inspection hole or overpass, which greatly simplifies further actions.
2. Remove the engine protection, if equipped.
3. Drain the oil and wait for the engine to cool. This is necessary in order to avoid getting burned when unscrewing the exhaust pipe.
4. Let's get to work and unscrew the nut of the clamp securing the exhaust pipe using a "17" wrench (if such a fastening is available).
5. Using a "14" wrench, unscrew the three nuts securing the exhaust pipe to the exhaust manifold. These nuts tend to stick, so it may be difficult to unscrew them. To simplify the process, we first clean them with a wire brush and treat them with WD-40.
6. Using the “17” key, unscrew the bolts securing the metal plate to which the clamp for securing the exhaust pipe (if present) is fixed.
7. The exhaust pipe is lowered, thereby freeing access to the Lanos engine sump. There is no need to remove it completely.
8. Using a “10” wrench, unscrew the bolts securing the plastic cover of the timing mechanism.
9. We proceed to unscrewing the 15 bolts securing the Lanos oil pan, using a “10” wrench.
10. All 13 bolts are located in plain sight and are easily accessible. Two bolts on the flywheel side are hidden under plastic plugs (if present).
11. It is with unscrewing these two bolts that owners of Lanos and Chance 1.5 cars have difficulty. The bolts are located in the channel (for clarity, a photo is shown below).
12. The main difficulty is that it is impossible to reach them using a standard ½ inch socket. To do this you will need a 3/8 inch tool.
13. Unscrew the 4 bolts securing the pan to the gearbox. One bolt is located on the side of the box. Shown in the photo below.
14. Two bolts are on one side.
15. And another one is located on the other.
16. After this, you can remove the pan. To do this, we use a knife and go around the perimeter of the part. The cover fits tightly to the engine, so there is no need to try to tear it off or knock it off, as it can be damaged.
17. The removed pan is subject to comprehensive cleaning and rinsing.
18. To carry out cleaning work, you need to unscrew the 8 x 10 bolts that secure the plate. Clean the deposits and rinse the part to the condition as shown in the photo below.
19. Don’t forget to remove any remaining old sealant around the perimeter of the pan and on the engine block.

Regardless of what caused the removal of the Lanos and Chance 1.5 crankcase cover, in any case it is necessary to clean its internal part, as well as dismantle the oil receiver and clean the metal mesh. If the oil pan needs repair, then after eliminating the defects using welding equipment, we proceed to assembly. If the part cannot be repaired, then you will need to buy a new pan, the cost of which for Lanos and Chance cars is about 3,000 rubles. Video instructions for removing the Daewoo Lanos 1.5 device.

Sequence of actions for replacing the gasket

Place the car over a hole or on an overpass so that it is convenient to get to the oil pan, otherwise removing it will turn into a “quest”. Having correctly placed the car over a hole or on an overpass and secured it securely (at least with a handbrake), you can begin the main process.

Going under the car, we see the oil pan protection, which we have to remove to get to the gasket.

The protection is attached to 4 bolts, which can be easily unscrewed with a socket wrench or a socket wrench. Having removed the protection and thoroughly wiped everything with a rag (and you will need a lot of it, because there is more than enough dirt), we see the oil drain plug.

The next step is to remove the engine protection, which prevents us from removing the pan. After this, unscrew the plug with a special key (hexagon) and drain the oil to remove the empty oil pan. Sometimes the drain plug can be tightened too tightly or become soured if it has not been unscrewed for a long time. In this case, we put a tube on the hex key; it will serve as an excellent lever.

Before draining the old oil, warm up the car engine, this will ensure more complete drainage (hot oil drains much better and faster). And it’s worth preparing a container for old oil in advance; the neck of the container should be as wide as possible, otherwise there is a danger of burning your hands with hot motor oil.

After this, unscrew the 19 bolts, which are evenly spaced around the perimeter of the pallet.

After unscrewing the bolts, we try to remove the pan. It is unlikely to succeed the first time; it rests on the oil pump. Exit - you need to raise the engine by unscrewing the engine mounts with a 17 key. The engine mount is attached on both sides, top and bottom, in both cases the same key is used, 17.

To remove the pan, you need to lift the car engine by at least 10 cm, otherwise all your efforts will go to waste. If everything is done correctly, we will see such a picture.

After removing the pan, carefully wipe it from the inside from oil and dirt, wipe the oil receiver, and remove the remnants of the old gasket.

Now we install a new gasket and carry out the assembly process. This is done in reverse order. The final touch will be to fill in new engine oil (don’t forget to change the oil filter).

Something else useful for you:

Here, in brief, is the entire process of replacing the cylinder block gasket; there is nothing overly complicated about it. The process (with associated work) takes on average no more than 5 hours, although experienced car mechanics do it much faster. But, as they say, experience comes with time.

3.24. Replacing the oil pan

Remove the engine splash guard. Drain the oil from the crankcase. Drain the liquid from the engine cooling system (see Replacing the coolant). Disconnect the upper radiator hose (see Replacing the engine radiator) and the lower radiator hose (see Replacing the thermostat).

We unscrew the four nuts securing the exhaust pipe to the exhaust manifold (see Replacing exhaust system parts) and use a 13mm wrench to unscrew the bolt securing it to the gearbox bracket.

Remove the exhaust pipe from the manifold studs and lower it.

We unscrew the two upper nuts securing the engine mounts (see Replacing the engine mount mount).

Using a wooden block, we rest the jack against the clutch housing (the engine can be lifted with a hoist).

We lift the engine, “helping” the pillow studs with a screwdriver to come out of the holes in the brackets.

Using a 10mm socket, unscrew the nineteen bolts securing the oil pan.

Reinstall the removed parts in reverse order. We recommend replacing the oil pan gasket with a new one, preferably one with cork chips in the rubber. We tighten the pan mounting bolts gradually, just as we did when replacing the cylinder head gasket. We lower the engine, using a screwdriver to adjust the studs of the pillows into the holes of the engine brackets. Fill the engine with fresh engine oil.

Installation

Install the new gasket and pan in the reverse order.

To distribute the gasket evenly, we tighten the oil pan mounting bolts in the direction from the middle to the edges.

Actually, why is this crankcase gasket necessary? The “tens” engine includes many units, components and systems. The crankcase is the engine body and plays a vital role. After all, it is it that contains all the main elements of the engine inside itself and provides them with the necessary protection and allows oil to circulate.

How to remove the pan on a VAZ 2114

Most car enthusiasts have heard about the existence of such a part in a car as an oil pan. But if you ask a beginner what it is needed for, what functions it performs and what it consists of, it will be quite difficult to get an intelligible answer. At the same time, everyone knows that the crankcase must be protected from mechanical shocks (there is even special protection for this).

Purpose of the oil pan and design features

The oil pan is shaped like a small bath of unusual dimensions. Depending on the make and model (and, accordingly, engine design), it may have a different configuration. Everything is done in order to prevent possible contact with the elements of the transmission located underneath or, for example, the front axle gearbox.

Some cars have a so-called “dry” sump. It has one interesting feature. The oil is not in the pan (as is usually the case), but in a special tank.

On most cars (including domestic cars), the task of the pan is to collect and store oil that circulates through the engine system. It is in the oil pan that all unnecessary debris settles, which can appear during the friction of various metal parts.

In addition, oil is collected in a special container, which at a certain point in time is not involved in the lubrication process. Subsequently, the composition is captured using an oil intake and sent to the main engine components. At the same time, the installation of such an oil “sucker” is well thought out. It captures oil not from the very bottom (where there is a lot of dirt and sediment), but a little higher. Moreover, in some models special magnets are installed at the bottom of the tray. Their task is to hold metal “chips” and prevent them from returning back to the engine.

On the inside of the crankcase there are special anti-drip bulkheads. Their task is to prevent oil from splashing during movement. In addition, the hole for draining oil from the engine is also located in the oil pan. Everyone (even beginners) knows how to check the oil level in the crankcase - this is done using a special oil dipstick.

The oil pan is a removable mechanism. It is fixed to the main unit using several bolts. In this case, a special gasket made of rubber or cork material is installed between the pan and the crankcase. Its task is to eliminate oil leaks at the junction of two elements. If the gasket is damaged, it should be replaced as soon as possible. If the malfunction is not noticed in time, the lion's share of the oil may leave the engine. The consequences for the most expensive component of a car can be very tragic.

Changing the oil pan gasket on a VAZ-2114

So, when the first symptoms of an engine oil leak appear, the first thing to do is inspect the engine. Damage to the gasket can be seen immediately by the appearance of a characteristic leak at the junction of the crankcase and the pan. The reasons may be different - natural aging of the material, poor quality of the gasket and its wear. In addition, problems with the gasket may appear after installing an initially defective product or insufficient (or, conversely, too strong) tightening of the bolts.

As for the gasket replacement process, it will take you no more than 20-30 minutes.

The algorithm of actions should be as follows:

1. Carry out the work in a viewing hole in the garage or use a lift. If this is not possible, then you can jack up the front of the car and install wooden trim.
2. Place special shoes to securely secure the car, apply the handbrake and engage first gear.
3. If your car has a metal crankcase protection, unscrew the mounting bolts and move the structure to the side (it will not be needed yet).
4. Start the engine and bring it to operating temperature. This is necessary in order to warm up the oil a little and reduce its thickness.

Pallet characteristics

This element is the lower part of a car engine (that is, the bottom of the cylinder block). What functions does this part perform? The element serves as a protective block. Oil is also stored in the pan. It cools down further when moving. Externally, the tray looks like a small bathtub.

The element is also a collection point for all impurities and particles that were formed during the operation of the piston group. The engine sump contains small metal particles and shavings - this is waste from the elements of the crank mechanism. Often a magnet is installed at the bottom of the pan, which absorbs all these impurities. The reader can see what it looks like in the photo below.

This is the transmission pan. There is also a pan gasket here. Automatic transmissions are required to be equipped with these magnets. Thanks to them, all metal shavings are attracted and retained in one place. This way it does not circulate throughout the system, working as an abrasive.

The pallet is mounted using mounting bolts. Just like at the junction of the block with the head, a gasket is used here. It is made of cork or rubber.

On older cars, the oil pan gasket was an ordinary sealant that was used to coat the joints and edges.

Lada Largus. Replacing the 1.6 (8V) engine oil pan gasket

We replace the oil pan gasket when an oil leak occurs at the junction of the pan with the cylinder block, as well as each time the pan is removed during engine repair.

We carry out the work on an inspection ditch or overpass.

We show the operations on a car with ABS and air conditioning.

We remove the protection of the power unit.

Drain the oil from the engine.

Disconnect the exhaust pipe from the exhaust manifold. Remove the rear support of the power unit. Unscrew the three screws securing the front bumper to the subframe (see “Removing the front bumper”).

Unscrew the rear subframe mounting bolts 3–4 turns (see “Removing the subframe”).

Having unscrewed the bolts securing the two subframe brackets to the body (see “Removing the lever”) and the bolts of the front fastening of the subframe to the body (see “Removing the subframe”), lower the front part of the subframe on the adjustable stand.

Using a 13mm socket, unscrew the nut of the bolt securing the power steering tube bracket to the cylinder block, holding the bolt from turning with a wrench of the same size.

Using a 13mm socket, unscrew the bolt securing the power steering tube bracket to the cylinder block bracket.

Using a 13mm socket, unscrew the bolt securing the oil pan to the cylinder block bracket.

On the left side of the subframe, use a 10mm wrench to unscrew the bolt securing the power steering tube bracket to the subframe.

We remove the power steering pipe from the subframe.

Using a 13mm socket, unscrew the four bolts securing the oil pan to the gearbox.

Using a 10mm socket, unscrew the 20 bolts securing the oil pan to the cylinder block.

Pulling the subframe down, remove the oil pan and remove it from behind the subframe.

We remove the sealing gasket from the grooves of the oil pan. We clean the mating surfaces of the cylinder block and oil pan from residual sealant and oil.

We wash the inner surface of the oil pan with kerosene.

Installing a new gasket...

...into the grooves of the oil pan. Before installing the oil pan, apply a thin layer of sealant...

...in the area of ​​the cylinder block cover (for clarity, shown on a removed engine)...

...and in the area of ​​the 1st main bearing cover. Install the oil pan and tighten its mounting bolts.

Tighten the oil pan mounting bolts to the prescribed torque (see.

Video on the topic “Lada Largus. Replacing the oil pan gasket for 1.6 (8V) engine"

Oil pan gasket for Renault K7J, K7M, K4M replacement. Oil pump inspection. | Video lecture #2

https://youtube.com/watch?v=nqxOvhKIkqg

How to change the engine sump - training video

Renault Sandero/Logan: Crankcase pierced, part 1

What's next?

After this, fill in the oil (first the old one) and start the engine. We make sure that the gasket does not leak. If everything is fine, drain the old lubricant and fill in new one. Don't forget about the oil filter. It changes along with the lubricant. Now all that remains is to replace the metal crankcase protection (if there was one) and lower the car from the jack. At this point, the replacement of such a part as the oil pan gasket has been successfully completed.

Advice for motorists, useful information on car repair and maintenance, engine running. Replacing the engine oil pan gasket Tips for repairing a VAZ car Tips for a car enthusiast.

It is advisable to time this action to coincide with changing the engine oil.

Need to:

wrench for unscrewing the oil drain plug (external hexagon 12); socket wrench 13; socket wrench 10; 10mm spanner (better if it is a dodecahedron); screwdriver; pad; flushing oil; oil for change; oil filter; rags.

Let's act.

We drive it onto a pit or a lift, or hang the front end.

We remove the standard crankcase protection with a 13mm socket wrench (do not lose the spacers on the rear two bolts).

We wash the pan and a little higher from dirt and oil.

Warm up the engine and turn off.

Open the filler neck.

Drain the oil from a hot engine by unscrewing the drain plug.

Using a 10 mm socket wrench, unscrew all the bolts securing the pan that are accessible (four bolts were inaccessible with a socket wrench: 2 above the beam and 2 near the resonator manifold).

Using a 10mm spanner, unscrew the 4 inaccessible bolts, holding the key (it will jump off because the pan has a collar) with a screwdriver or other improvised means (do not lose the washers!).

It is advisable not to tear the old gasket, but to remove it intact to determine the cause of the leak. To do this, use a screwdriver or your fingers, if it is not already hot, to release the gasket.

We recess it from one side into the pallet, taking out the other edge through the bottom.

We assess the condition of the gasket, if everything is normal and it siphoned due to old age and damage, then

Take a new gasket and lubricate it with flushing oil.

We clean the surfaces of the pan and the engine in contact with the gasket and lubricate them with flushing oil.

We put the gasket through the bottom, just like we removed the old one (do not tear it!).

We tighten (do not tighten!) the bolts, making sure that the ribbed side of the washer is directed towards the bolt head. It is better to bait diagonally, that is, front - back, left side - right side, etc. At the same time, make sure that the holes in the gasket coincide with the holes in the pan. When all the bolts are tightened with 1-2 threads, tighten them until they touch the pallet (do not tighten them!). We make sure that the gasket lies flat and there are no distortions or folds anywhere. Now let's start tightening it up. This must be done strictly diagonally to avoid distortion and damage to the gasket. The first circle is through two bolts, then through one, and finally every bolt. During the entire operation, we monitor how the gasket lies (evenly and without folds), otherwise everything will be done again with a new gasket.

Screw in the drain plug.

Fill in the flushing oil and wipe dry all traces of oil in the area being examined and close the filler neck.

We flush the engine at MINIMUM speed, do not waste time, check for leaks.

If there is a leak, retighten ALL bolts to avoid distortion

Unscrew the filler neck, drain the flushing oil, and remove the oil filter.

We take the gasket out of the new filter, lubricate it with new oil on both sides, put the gasket in place, pour a little oil into the filter and tighten the filter BY HANDS.

Screw in the drain plug.

Fill in the prepared fresh oil, close the filler neck and wipe the entire area to be examined dry.

We start the engine. We check in several stages whether there is a leak: 1500 rpm, 2000, 3000, 4000 for 30 seconds - 1 minute. If there is a leak, then on a hot engine it will still be possible to tighten the filter and tighten the bolts; if the leak is not eliminated, then you need to think

We put the standard crankcase protection in place, don’t forget to put the spacers in place on the two rear bolts.

We run the engine under load and keep possible leak areas dry and clean so that leaks can be localized.

Actually, why is this crankcase gasket necessary? The “tens” engine includes many units, components and systems. The crankcase is the engine body and plays a vital role. After all, it is it that contains all the main elements of the engine inside itself and provides them with the necessary protection and allows oil to circulate.

The crankcase includes two collapsible elements, between which the gasket is located. It is responsible for sealing the connection between two crankcase elements and prevents oil from leaking out of the system, which, by the way, is under high pressure.

Installation of seal

Before installing a new gasket, all traces of leaks must be removed. Experienced motorists advise not only to wipe the pan, but also to degrease it. The same actions are recommended for the surface of the block. It is advisable to remove, wash and blow out (at least with a regular tire pump) the so-called “gander”. When installing it back, you can lubricate the rubber ring of the “gander” with sealant for better fixation.

At a distance of 3 mm

A layer of the same sealant is applied from the inner perimeter. The sealant is laid out on its bed as evenly and quickly as possible, and a similar layer is applied on top. Bolts are baited; If the instructions supplied with the car do not indicate the exact order of tightening them, screw in the fasteners diagonally, crosswise, so as not to unevenly pinch any of the sides.

Hello, in this article you will learn how you can independently replace the oil pan gasket on a VAZ 2108, 2109, 21099. This gasket is replaced when oil begins to squeeze out from under it. It is better not to delay replacing the pan gasket, as every day it can begin to leak more and more. As a temporary measure, you can try tightening the pallet mounting bolts, but even if this is enough, it won’t last long. To replace the pan gasket, you will need a 10 socket and a 17 wrench. The cost of a pan gasket on a VAZ 2108, 2109, 21099 averages 100-200 rubles. First you need to drain the oil from the engine. After this, you need to unscrew the bolts securing the protective cover of the clutch housing and remove it

How to remove the oil pan (engine oil pan) without removing the engine

The oil pan is a reservoir located under the engine and is designed to collect unused oil that circulates throughout the system. This element resembles a metal bathtub, has a simple structure, and is therefore not susceptible to breakdowns. However, there are times when the container breaks through during off-road travel, or simply rusts. To remove the oil pan, you need to know not only its location, but also its design features.

• Where is the oil pan located and what does it look like?
• Crankcase Removal Tools
• How to remove the oil pan on a domestic car
• How to remove the oil pan on a foreign car
• Possible problems when removing the engine sump

How to remove and install the oil pan yourself

This is not a complicated procedure, and most car enthusiasts can do it, although it does require some repair skills and tools. Depending on the brand of the car, nuances are possible. For example, in VAZ cars of the classic family, with a longitudinal engine, you need to lift the engine. Therefore, before you start disassembling it yourself, read the repair manual for your car.

Procedure for removing the oil pan:

• Prepare a clean container - it can be a canister with a wide neck or a cut one. Its volume must correspond to the amount of oil in the engine of your car;
• Drive onto an inspection hole or overpass; it will be more convenient for you if it is deep enough so that you can stand under the car at full height;
• Warm up the engine to a temperature of 50-60 degrees, the engine oil will become thinner and more fluid;
• If the engine compartment protection is installed, remove it; it is usually secured with 3-4 bolts;
• Carefully unscrew the drain plug, placing a previously prepared container under it, be careful - the oil will definitely flow onto your hands and possibly somewhere else;
• Unscrew the oil filler plug. After unscrewing the filler plug, the flow of escaping oil will increase sharply, make sure that it flows into the canister and losses are minimal;
• Wait until all the oil has drained and begin unscrewing the fastening bolts/nuts;
• If all the bolts are unscrewed and the oil pan cannot be removed by hand, this means that the parts have been glued together. You need to tap it with a rubber hammer, carefully pry it with a screwdriver or other flat object, but so as not to damage the joints. Scratches may cause leaks in the future.

Now that the pan has been removed, you can carry out repairs and also see the crankcase structure.

What oil is better to pour?

Choosing a car oil is the most crucial moment, requiring care and a particularly thorough approach. The lifespan of your engine will depend on the type of engine oil you use. It is better to fill the engine with high-quality lubricant to extend the life of the engine.

Please note the requirements of the API standard. The choice is also made taking into account the viscosity of the material

Here it is necessary to take into account the seasonal factor. Correctly selected viscosity indicators will ensure normal engine operation in any weather.

Mineral motor oil does not last as long as synthetics or semi-synthetics, moreover, it is not effective at low and high temperatures, however, it is gentle on engine parts. Any of the three types is suitable for the LADA Samara car engine. It's up to you to decide which product is best to use. There are a great many manufacturers producing motor oils; you can choose a high-quality product, but when choosing, you should take into account all the characteristics.

Symptoms of a problem

If the replacement is carried out incorrectly, the rupture may occur again, foreign particles will get inside the crankcase, sealing will be insufficient, which will lead to failure of the engine or its individual components.

It would seem like a simple gasket, but what a burden of responsibility lies on it.

To determine the need to replace the gasket, you should pay attention to the characteristic signs of such a problem:

1. Oil is leaking.
2. There is a decrease in pressure in the oil system.
3. The oil level drops more rapidly than usual.

How to replace the oil pan and its gasket on a VAZ 2101-VAZ 2107?

Note! This method is not always suitable for people to remove the pan from a car, because not everyone has items that facilitate this, so at the very end of the article there is a video that shows the procedure for removing and replacing the pan and gasket without the use of special tools!

Removal: 1) Before starting work, drive your car into the inspection hole.

2) Then remove the crankcase protection from the vehicle. (How to remove the protection, see the article: “Replacing the crankcase protection”)

3) Then completely drain the engine oil from the car engine. (How to drain the oil, see the article: “Changing engine oil”)

4) Next, unscrew the two nuts on both extreme sides that secure the right and left engine mount to the cross member.

5) Next, install the “Travece” on top of the engine compartment, it is indicated by the number “1” in the photo, and then begin to tighten the nut under the number “2” and thereby lift the engine from the car.

Note! You need to lift the engine until the ends of both studs, numbered “1”, coincide with the flat part of the engine mount brackets, which are indicated under the number “2”!

6) Now, using a wrench or an extension with a hinge and cap, unscrew the “19” bolts that secure the pan to the engine.

Note! There are washers under each bolt, so be careful not to lose them!

7) And finally, use a screwdriver to carefully separate the oil pan from the cylinder block and, as a result, remove it along with the gasket.

Note! If the gasket is stuck to the block, then use a sharp object to remove it and clean the entire plane of the block from pieces of the gasket!

Installation: 1) First, use a clean cloth to wipe the mating surface of the block, and then the oil pan.

Note! There is no need to degrease the surfaces of the block and tray using products such as White Spirit, etc. Because in the future, this will make it easy to disassemble the connection!

2) Next, lubricate both sides of the gasket with a thin layer of silicone sealant to ensure that engine oil does not leak through the gasket in the future.

3) Finally, install all the removed parts in their place, in the reverse order of removal.

Note! Replace all deformed parts with new ones, and tighten the “19” bolts that secure the oil pan during installation crosswise. When tightening the bolts, do not use much force because this may damage the crankcase flange and the gasket may be deformed!

Additional video: For more detailed instructions on removing and replacing the gasket and pan, see the video below:

Preparing for work

Preparation plays a big role in successfully replacing the oil pan gasket. Actually, this event will not be very difficult.

• Drive the car into the pit or lift it using a lift;
• Provide high-quality light so that you can carefully inspect the condition of the pallet;
• Remove the crankcase protection if you previously installed it on your VAZ 2110;
• The oil pan must be cleaned because a large amount of dirt and oil accumulates on it. It is also recommended to clean the areas adjacent to the oil pan;
• The easiest way to detect a leak is when the engine is warm, but only at idle speed. This will increase the pressure in the oil system and will show how serious the problem is with oil leaking through the oil pan gasket.

Repair

Removing the oil pan is a fairly simple procedure, which is performed after first hanging the car on a lift. During its implementation, the specialist inspects the condition of the pallet and its internal part, after which a decision is made on the advisability of replacing it. It goes without saying that if the source of the oil leak is the gasket, the pan will not need to be replaced. The entire removal and installation procedure takes about an hour.

At the same time, installing the oil pan in place is a more labor-intensive operation, since it requires careful adjustment and careful tightening of the bolts. It should be noted that during the procedure, regardless of its tasks, it is necessary to replace the gasket, as well as the oil in the vehicle’s power unit. In addition, it would be useful to install engine protection on the car in order to protect the sump from possible damage.

• Sign up for repairs
• or by phone:
• +7

Signs

The first sign by which you can recognize a gasket leak is an oil leak at the junction of the pan with the internal combustion engine. But since this element is the lowest point of the engine, it is not always possible to recognize a breakdown in time. Moreover, the scale of the problem can be different - from slight “fogging” to black oil puddles. The first option is not so scary for the car owner. Some drivers have been driving with this for years. However, if after a short parking period oil streaks form on the asphalt, it is worth inspecting the condition of the pan.

Also, a pan gasket that has lost its tightness affects the oil level. It will gradually decrease. How intensively the oil will leak depends on the scale of the tragedy. Driving with a dry engine is extremely dangerous. Once every thousand kilometers, experts advise checking the level on the dipstick. It should be above the average mark.

If it is at a minimum, the engine will experience oil starvation. Inserts, rings and other elements work “dry” - ellipse of the cylinders and other problems are formed.

Possible problems when removing the engine sump

Usually it is not possible to remove a part if the bolts are rusty. They need to be unscrewed carefully so that the pins do not break off. It is necessary to preheat the mounting location, and then slowly unscrew the bolt. In domestic cars, the bridge often gets in the way after unscrewing the fasteners. In this case, you should not try to cut off the interfering strips. The problem is solved by removing the oil pump.

It is important to raise the engine to a sufficient height. Otherwise it will be impossible to get to the pallet

The engine is raised until it reaches the nuts securing the mounts. It is convenient to use a diamond-shaped jack for this operation. It needs to be installed under the box; when lifted, the engine will move. Procedure:

1. Disconnect the receiving pipe from the manifold, pull out the rods coming from the radiator and heater.
2. Disconnect the gas draft loop located on the right, unscrew the casing from the stove.
3. Pull out the oil dipstick. Disconnect the tube in which it is placed.
4. Remove the clutch box, and then the shield located below the radiator.
5. Disconnect the rear support post from the crossbar. Raise the box with a jack, then the handbrake drum will begin to rest against the body. The rear pillar will have to be supported.
6. Place a jack under the crankcase and disconnect the cushions. Raise the engine until it stops.
7. Place several planks between the motor feet and the cushions. Remove the jack and carefully secure the engine.
8. Unscrew the fasteners that hold the crankcase in place. To do this you will need a key with a universal joint. To remove the tray, you need to pull it back.

If there is no jack, a traverse made of timber will do. The beam must be positioned parallel to the radiator. Next, the pin is attached to the engine and threaded through the yoke. Then you need to carefully tighten the nut on the stud. The motor will begin to rise slowly.

It happens that when you try to pry the pan with a screwdriver, it does not budge. In this case, the part gets stuck somewhere inside. First you need to check that all the bolts are unscrewed. In most engines, the cover is held on by 15 bolts, less often by 14. If everything is unscrewed, this means that the oil intake tube is stuck. To solve the problem, you will have to unscrew the tube from the pump.

Tips and tricks

It is possible to dismantle the part only if the preparatory work is carried out correctly. First, the car is placed above the inspection hole; if this is not possible, the body is raised with a jack. After this, it will be possible to get to the crankcase and adjacent parts.

To carry out manipulations, good lighting is required. Without illumination, it is difficult to remove a spare part from a hard-to-reach area. If you have a powerful lamp, it will be possible to inspect the pallet and make sure that there are no dents or holes on it. You will also have to check the condition of the gasket.

If a hole has formed in the housing, repairs can be made using argon welding. Minor cracks are repaired by cold welding, but before doing so, the oil is drained and the surfaces are degreased. Leaks at the junction of the engine block and the sump indicate the need to replace the crankshaft oil seal. Slight sweating around the drain plug is not considered a deviation from the norm.

Welded engine sump

The pan can be accidentally punctured when driving off-road, even with high ground clearance. Many car owners install protection that covers the pan from impacts and complicates access to it. The protection is dismantled in advance; it is usually held on by several bolts and can be unscrewed without any problems.

Before dismantling, it is advisable to wipe the tray and surrounding elements with a rag. This makes it more convenient to carry out work, and it is easier to see damage to the body. If oil spills out, the location of the leak is determined visually. To check the integrity, you need to turn on the engine at idle speed. In this mode, oil will quickly begin to flow out through the hole. If after removal you find damage to the gasket, do not throw it away. It is better to take the old seal with you when going to the store. Then it will be easier for the seller to select a similar spare part.

Deformation, extrusion

Spontaneous deformation of the gasket often occurs. You need to understand that this sealing element is subject to high loads, pressure and temperature changes. And if on the street side the air temperature can be +15 degrees, then inside the pan the oil is heated to 110 degrees Celsius.

Also, the pan gasket is subject to deformation due to high pressure in the oil system. What could cause this phenomenon? Often, oil seals and gaskets are squeezed out due to dirty The element must allow a mixture of oil vapors and condensate to pass into the inlet pipe. If the valve does not work, the high pressure in the engine squeezes out all the sealing elements. This does not happen right away. However, replacing these parts will cost a pretty penny. Moreover, not only the parts themselves are expensive, but also the work to replace them (for example, the rear crankshaft oil seal). To prevent this from happening, periodically check the crankcase ventilation system.

Removing and installing the oil pan and oil intake of the Nissan Patrol oil pump

Removing and installing the oil pan and oil pump oil intake

Removal

Installation

Installation is in the reverse order.

Replacing the oil pan and its gasket on a VAZ 2101-VAZ 2107

Today, many people already know such a thing as an oil pan, but not everyone knows what it really is, when it needs to be changed and how to properly replace it on cars of the “classic” family - we will look at these questions today.

To replace the pan and its gasket, you will need to prepare a few things in advance: First, be sure to stock up on wrenches, or you can use an extension, universal joints and sockets instead!

Where is the oil pan and its gasket located?

The pan is located at the very bottom of the car engine; unfortunately, in order to fully see the pan it is necessary to remove the crankcase protection, which is done in the figure below:

The blue arrow indicates the gasket that is located between the cylinder block and the crankcase pan!

When do you need to replace the oil pan and its gasket?

The pan must be replaced if it is deformed, due to which the engine oil that was located in it begins to flow out of the pan itself.

The pan gasket must be replaced if it is strongly compressed and if it is torn, how do you understand this, you ask? Usually, when the gasket is deformed, engine oil begins to flow through it, but the leak can also be treated by simply tightening the bolts that secure the oil pan, but if tightening the bolts does not produce any results and the leak does not stop, then replace the gasket with a new one.

How to replace the oil pan and its gasket on a VAZ 2101-VAZ 2107?

This method is not always suitable for people to remove the pan from a car, because not everyone has items that facilitate this, so at the very end of the article there is a video that shows the procedure for removing and replacing the pan and gasket without the use of special tools!

• Before you start work, drive your car into the inspection pit.
• Then remove the crankcase protection from the vehicle. (How to remove the protection, see the article: “Replacing the crankcase protection”)
• Then completely drain the engine oil from the car engine. (How to drain the oil, see the article: “Changing engine oil”)
• Next, unscrew the two nuts on both extreme sides that secure the right and left engine mount to the cross member.

Next, install the “Travece” on top of the engine compartment, it is indicated by the number “1” in the photo, and then begin to tighten the nut under the number “2” and thereby raise the engine from the car.

Common unit breakdowns

• operational wear of the components of the unit: the pump housing or gears fail: during the operating cycle, the gap between the driven and driving gears increases. In normal condition it does not exceed 0.25 mm. Wear leads to the fact that the distance between the parts increases to 0.5 mm: the gears no longer mesh. The described breakdown makes the oil pump unsuitable for routine repairs - it is easier to buy a new part than to install new gears and adjust them;
• leakage: oil begins to leak from under the pump. The reason for this is a leaky oil pump gasket. Replacing the gasket solves the problem;
• Oil receiver clogged: The oil receiver becomes clogged due to a clogged crankcase. In this case, you need to dismantle the oil pan and clean the mechanism.

In most cases, it is necessary to purchase a new oil pump. The price of a new part in online stores is in the range of 1700 - 2500 rubles. The devices are compatible with the first generation Samara.

Signs and causes of oil pump malfunction Lada 2114

There are several markers, the appearance of which will allow you to suspect defects in the pump:

• The corresponding light on the dashboard lights up;
• Oil puddles regularly form under the car;
• Smoke is generated during engine operation.

Causes of unit malfunctions:

• use of motor oil that does not comply with the car manufacturer’s recommendations;
• oil filter clogged;
• permanently low level of lubricating fluid in the crankcase;
• non-working condition of oil level monitoring devices;
• failure of the engine lubrication system valve;
• impurities entering the engine oil (most often coolant is mixed with it).

All the described breakdowns are accompanied by activation of the control lamp, so do not delay repairs; begin service operations after activating the control indicator.