Windshield washer diagram for VAZ 2107 injector

Cars have special equipment for travel during bad weather associated with precipitation. The windshield of the VAZ 2107 is cleaned of water using movable brushes, and in case of contamination, the washer is activated. This device sprays a special liquid, it works simultaneously with the windshield wipers and removes dirt.

The equipment thus provides the necessary visibility for the driver and passengers. This device includes the following elements:

1. Liquid reservoir.
2. A pump that runs from the on-board network.
3. Nozzles that blow a water jet onto the windshield of a car.
4. Tubes connecting the tank to the actuators.

At the end of the summer season, the water in the system is replaced with non-freezing liquid, which will allow the system to be used in winter.

VAZ 2107 washer does not work reasons, repair

On a VAZ 2107 car, the wipers are driven by a 12 V electric motor. A relay is installed in the windshield wiper activation circuit.
It is responsible for the intermittent operation of the wipers, which work without interruption or at intervals of four seconds. The windshield wiper is connected in parallel through the contacts of the closer. They are located in the gearbox housing and are “responsible” for returning the brushes to their original position and abruptly stopping the motor. The driver controls the operating mode of the windshield wiper using the switch. The whole mechanism works thanks to a motor. It is prohibited to operate a car with faulty wipers, so car owners must ensure that they are in good working order. And in bad weather, driving with non-working wipers is very dangerous!

Why doesn't the windshield washer work?

The system for cleaning glass and car headlights includes: a liquid reservoir, a pump, nozzles, tubes, electrical wiring and a power button.
Most often, the reason why the windshield washer does not work is a faulty motor or a blown fuse. The operating principle of a windshield washer is quite archaic, so simple diagnostics and simple repairs can be performed almost at the doorstep of the nearest auto parts store. Malfunctions and operating principles of hand and foot-operated windshield washers, which were installed on some VAZ and AZLK models, deserve a separate topic and will not be discussed in this article.

Causes of failure

• The windshield washer pump fuse has blown. Manufacturers mark consumers who are protected by fuse links with graphic symbols on the inside of the relay and fuse box cover. If the markings are unclear or the required insert is not marked, a detailed fuse location diagram can be found in the repair and operating manual for your car. Attention! Installing a larger fuse may cause the vehicle to catch fire. If the new fuse-link burns out immediately after installation, there is a short circuit in the circuit.
• The windshield washer motor is burnt out or soured. The low cost of the pump makes its disassembly and repair impractical, so simply replace it with a new one.
• The contacts on the connectors have oxidized, the power wires have become frayed or broken. In field conditions, oxides can be removed from the terminals with a sharp object. At the same time, do not damage or bend the terminals so as not to disrupt the quality of contact in the connector.
• The coarse filter in front of the windshield washer pump is clogged (not installed on all cars). The filter is attached to an O-ring that seals the pump installation location. If trouble catches you on the road and you cannot clean the filter element, temporarily remove it from the line.
• The hose from the pump to the injectors has fallen off or broken.
• The injectors are clogged. In winter, injectors can become clogged not only with debris and plaque, but also with ice. After using the windshield wiper, a washer fluid remains on the nozzles, from which the alcohol evaporates over time. The water remaining near the nozzle freezes, which is why the windshield washer does not work. You can pierce the injectors with a thin needle.
• The fluid in the washer reservoir has frozen.

Operating principle and connection diagram

The pump consists of a centrifugal wheel that is rotated by a DC electric motor. The liquid captured by the wheel is supplied through tubes to the nozzles. Below is the simplest diagram for switching on the glass washer for VAZ 2104, 2105, 2107 cars.

When the driver activates the windshield washer, the contacts inside the switch close, the gray-black wire connects to the vehicle ground - current begins to flow in the windshield washer circuit.

On VAZ 2110, 2111, 2112, relay K2 is responsible for turning on the windshield washer. It is through this that + is supplied to the pump connector. The second terminal of the electric motor is connected to the car body. A method of constructing a circuit close to this is used on most modern cars.

Where to start diagnostics?

If your car's windshield washer does not work, pay attention to the characteristic symptoms. The electric motor hums when turned on, but liquid does not splash from the nozzles onto the windows. To check, just turn off the engine, turn on the ignition and switch the steering column switch to the windshield washer position. Most likely, the reason is clogged nozzles, a filter element, a flown off, kinked or burst hose.

The windshield washer motor is silent when turned on. There is a problem with the pump, wires or steering column switch. If the fuse is good, proceed to diagnosing the power supply circuit.

The windshield or headlight washer pump requires + and – to operate. Depending on the connection diagram, when you move the steering column lever, one of the wires is shorted to ground or acts as a power wire (a + appears on it). Accordingly, the second wire is either constant + after turning on the ignition, or shorted to ground. The search for an open circuit or short circuit should begin with studying the electrical circuit.

Power check

In order to understand whether the pump is faulty or there is a power problem, it is enough to check the electrical circuits. If you don’t have one with you, use any 12V light bulb and two pieces of wire. Connect one control terminal to the car body, and the second to the positive terminal of the pump connector. If the light comes on after turning on the ignition, unhook the control terminal from the body and connect it to the + battery. Connect the second end of the control to the terminal, which should be shorted to ground when the windshield washer is turned on. If the light comes on, there is no problem with the power supply and the reason is in the motor. A method for checking the windshield washer power supply on VAZ 2104, 2105, 2107 is described, but the approach to finding power at the pump connector is relevant for all cars. To quickly check the windshield washer motor, two wires are enough. Forcefully supply power from the battery to the motor terminals. If the motor does not hum, it must be replaced.

When you turn on the windshield washer, the wipers make several sweeps in automatic mode. If this does not happen, start by checking the steering column switch, relay and wires from the switch to the pump. To do this, arm yourself with the same tester or multimeter. A tester in resistance measurement mode is also necessary to check the integrity of the wires. To test, connect the multimeter probes to the ends of the wire. The inscription OL (Over Limit) indicates a break or break in the wire.

Source: autoburum.com

Windshield washer pump VAZ 2107

Cars have special equipment for travel during bad weather associated with precipitation. The windshield of the VAZ 2107 is cleaned of water using movable brushes, and in case of contamination, the washer is activated. This device sprays a special liquid, it works simultaneously with the windshield wipers and removes dirt.

The equipment thus provides the necessary visibility for the driver and passengers. This device includes the following elements:

1. Liquid reservoir.
2. A pump that runs from the on-board network.
3. Nozzles that blow a water jet onto the windshield of a car.
4. Tubes connecting the tank to the actuators.

At the end of the summer season, the water in the system is replaced with non-freezing liquid, which will allow the system to be used in winter.

System diagnostics

To understand the reasons for the inoperability of the windshield washer on the VAZ 2107, you should first of all consider the design of the system. It consists of the following elements:

1. Washer fluid reservoir.
2. A pump with an electric motor, which operates from a 12V network.
3. Nozzles or sprayers of a water jet that hits the windshield.
4. PVC pipes connecting the above elements.

A special liquid is poured into the washer reservoir, one type in summer and another in winter. Winter liquid is called “anti-freeze”, with its help you can effectively wash windows at sub-zero air temperatures, and not worry about the fact that it may freeze in the system.

When the washer is turned on, liquid is sprayed onto the windshield with the simultaneous automatic activation of the wipers. If, when you turn on the device, there are no signs of its performance, then you can determine the cause of the breakdown yourself. The electrical diagram for connecting the washer on a VAZ 2107 is presented below, based on which you can sort out the malfunctions.

Why does the windshield washer not work?

To determine why the windshield washer on the seven stopped working, it is necessary to carry out a thorough diagnosis. To help you carry out self-diagnosis, use the diagram shown in the photo above. Once a faulty element is detected, it will need to be repaired or replaced, depending on the nature of the failure. Malfunctions of the element in question can be divided into minor (you can fix it yourself) and serious, requiring replacement of the faulty part. Let's take a closer look at the main components of the system and their malfunctions.

Where does which wire go, or just a diagram

Connecting wipers and washer

“Plus” power is supplied from the ignition switch through fuse No. 2 at 10 Amp of the mounting block. The permanent “plus” goes along the black and yellow wires to contacts “4” of the connectors of the gear motor and the steering column switch. It should not disappear even when the switch is in the “off” position. The blue wire supplies “+” 12 V power to the motor when the switch is in “continuous mode” position. On the blue-white wire, in the “off” position there should be a “minus”, and in the “continuous mode on” position the “minus” is turned off. This is done to slow down the motor when the power to the closer is turned off.

The red wire supplies the relay with “+” 12 V from the switch when the intermittent mode is turned on. At the moment of operation, contacts “2” and “4” close, and “1” and “3” open, the motor starts working and the brushes make one or two movements. Then “+” 12 V is turned off, and contacts “1” and “3” are closed to each other and to “minus”. The motor stops for a few seconds and then the cycle repeats.

VAZ 2107 washer does not work

Unread message JET » Sun Dec 13, 2009 20:13:11

Yes, there has never been any relay in this circuit. The relay is located on the circuit of the headlight beam washers and cleaners.

Check the wires according to the diagram below1. The second one is for clarification about the relay. On the hot wire +, the washer is controlled by minus. Check fuse No. 2 and the power supply to the motor. There are 2 options for steering column controls: 1 - the washer works only when the wipers are turned on. 2- regardless of whether the wipers are turned on

Unread message by Zayec » Sun Dec 13, 2009 20:29:04

Main causes of failures of additional equipment

If the washer on the car does not work, it is necessary to diagnose it using simple techniques. This system may fail for a number of reasons, which are listed below:

1. breakdown of the injection pump;
2. fuse blown;
3. kinking or squeezing of the supply hose;
4. breakdown of the steering column switch;
5. freezing of water in pipelines or other devices;
6. loss of contact in the electrical network.

It is possible to determine the cause of the malfunction and the amount of costs to restore the system's functionality based on the results of a careful inspection. If you need to replace individual parts or elements, you can do it yourself. The device that blows the windshield to clean it from fresh or dried dirt does not work.

Most likely, you will need to replace failed equipment.

VAZ 2107 washer motor does not work

Cars have special equipment for travel during bad weather associated with precipitation. The windshield of the VAZ 2107 is cleaned of water using movable brushes, and in case of contamination, the washer is activated. This device sprays a special liquid, it works simultaneously with the windshield wipers and removes dirt.

The equipment thus provides the necessary visibility for the driver and passengers. This device includes the following elements:

1. Liquid reservoir.
2. A pump that runs from the on-board network.
3. Nozzles that blow a water jet onto the windshield of a car.
4. Tubes connecting the tank to the actuators.

At the end of the summer season, the water in the system is replaced with non-freezing liquid, which will allow the system to be used in winter.

Product Description

The compact windshield washer motor BAK.21109 is made from high-quality components and carefully balanced for stable operation over a wide temperature range. The small-sized electric windshield washer motor has been factory tested and certified for use in the Russian Federation and the countries of the Customs Union. The impeccable functionality of electrical equipment and low noise level during operation are based on the company's advanced developments and high quality assembly operations. This electric motor is completely interchangeable with the washer electric motor 2110-5208009.

. ATTENTION.

Don’t forget to replace the washer fluid in the washer reservoir with non-freezing fluid in winter. Freezing of the fluid in the reservoir can damage the windshield washer motor.

This product has official awards:

BelAK electric motors received the prestigious national award “Automotive Component of the Year 2016”.

Operating principle

On a VAZ 2107 car, the wipers are driven by a 12 V electric motor. A relay is installed in the windshield wiper activation circuit. It is responsible for the intermittent operation of the wipers, which work without interruption or at intervals of four seconds.

The windshield wiper is connected in parallel through the contacts of the closer. They are located in the gearbox housing and are “responsible” for returning the brushes to their original position and abruptly stopping the motor. The driver controls the operating mode of the windshield wiper using the switch. The whole mechanism works thanks to a motor. It is prohibited to operate a car with faulty wipers, so car owners must ensure that they are in good working order. And in bad weather, driving with non-working wipers is very dangerous!

Electric motor for windshield wiper VAZ 2107, diagram

The VAZ 2107 car is equipped with an electric windshield wiper motor (wipers), which can clean it in intermittent and continuous modes.

Here is a diagram of its connection with a description of its features and operating procedure, which can help if any malfunction occurs with it.

Wiring diagram for the electric motor of the windshield of a VAZ 2107 car

Connection diagram for the electric motor of the windshield wiper (windshield wipers) of the VAZ 2107 car

Description of the connection diagram for the electric motor of the windshield wiper VAZ 2107

— Voltage in the electrical circuit for switching on the windshield wiper motor is supplied from the positive terminal of the battery through terminal “30” of the generator and the ignition switch. That is, you can turn on the wipers only after turning the key in the lock.

— The electrical circuit is protected by fuse F2 (10A) in the mounting block.

— The electric motor of the wiper is turned on using the lever of the right steering column switch: the first position is intermittent mode of the wipers, the second position is the brushes work constantly.

— When the intermittent operation mode of the wipers is turned on, electric current flows through the breaker relay RS-514. There it goes from the steering column switch through the red wire to the relay electromagnet and its thermobimetallic breaker and then through the gray wire to the wiper motor.

When current passes, the relay breaker plate heats up, bends and opens the breaker contacts. In this case, the contact of the electric motor switch is closed to ground (yellow wire from the steering column switch to the relay and blue-white wire from the relay to the electric motor). The electric motor stops. After which the breaker plate cools down, straightens and again closes the contacts inside the relay, the voltage is again supplied to the electric motor. He starts working. Such on and off cycles are repeated with a frequency of 9-17 times per minute.

Notes and additions

— On a VAZ 2107 car and its modifications of different years of production, as well as on VAZ 2104, 2105 cars, the color of the wires in the windshield electric motor connection diagram may differ from the one shown above.

— In addition to the windshield cleaner, the VAZ 2107 has a washer, consisting of an electric motor for a pump in the washer fluid reservoir, pipes and spray nozzles. It is turned on by the same right steering column lever (move it towards you to an unfixed position). Here is its connection diagram “Windshield washer connection diagram for a VAZ 2107 car.”

Twokarburators VK - More information on the topic in our VKontakte group, on Facebook Twokarburators FB and on Odnoklassniki - Twokarburators OK

More articles on the electrical equipment of the VAZ 2107 car

— Cigarette lighter for VAZ 2107, connection diagram

— Fog lights (PTF) of the VAZ 2107 car connection diagram

— Electric motor “stove” VAZ 2107 connection diagram

— Connection diagram for low and high beam headlights of a VAZ 2107

— External lighting switch VAZ 2107

— Connection diagram for heating the rear window of a VAZ 2107 car

We disassemble the turn switch for a VAZ 2107

And although many manufacturers of turn switches claim that this is a completely non-separable design, it can still be disassembled with some effort. Disassembly of devices is necessary when repairing it. It takes place in several stages:

1. Using a 3 mm drill, drill out the 2 upper rivets and remove the upper part that is attached to the tube;
2. After removing this part we see 2 more rivets that hold the ring;
3. Carefully remove the ring from the grooves, then you need to remove additional rings and levers.

Mechanical breakdowns

The most common reasons why the VAZ 2114 windshield washer does not work are mechanical damage.

The most common of them are:

1. the washer fluid has run out in the tank;
2. the pipeline leading to the windshield wiper is clogged;
3. the windshield wiper nozzles are clogged;
4. the water used as washer fluid froze;
5. the hose fell off the pump;
6. the hose going to the windshield wiper is pinched;
7. The supply hose has ruptured.

VAZ 2107 windshield washer does not work

Content

The system for cleaning glass and car headlights includes: a liquid reservoir, a pump, nozzles, tubes, electrical wiring and a power button. Most often, the reason why the windshield washer does not work is a faulty motor or a blown fuse. The operating principle of a windshield washer is quite archaic, so simple diagnostics and simple repairs can be performed almost at the doorstep of the nearest auto parts store.

Malfunctions and operating principles of hand and foot-operated windshield washers, which were installed on some VAZ and AZLK models, deserve a separate topic and will not be discussed in this article.

Causes of failure

• The windshield washer pump fuse has blown. Manufacturers mark consumers who are protected by fuse links with graphic symbols on the inside of the relay and fuse box cover. If the markings are unclear or the required insert is not marked, a detailed fuse location diagram can be found in the repair and operating manual for your car. Attention! Installing a larger fuse may cause the vehicle to catch fire. If the new fuse-link burns out immediately after installation, there is a short circuit in the circuit.
• The windshield washer motor is burnt out or soured. The low cost of the pump makes its disassembly and repair impractical, so simply replace it with a new one.
• The contacts on the connectors have oxidized, the power wires have become frayed or broken. In field conditions, oxides can be removed from the terminals with a sharp object. At the same time, do not damage or bend the terminals so as not to disrupt the quality of contact in the connector.
• The coarse filter in front of the windshield washer pump is clogged (not installed on all cars). The filter is attached to an O-ring that seals the pump installation location. If trouble catches you on the road and you cannot clean the filter element, temporarily remove it from the line.
• The hose from the pump to the injectors has fallen off or broken.
• The injectors are clogged. In winter, injectors can become clogged not only with debris and plaque, but also with ice. After using the windshield wiper, a washer fluid remains on the nozzles, from which the alcohol evaporates over time. The water remaining near the nozzle freezes, which is why the windshield washer does not work. You can pierce the injectors with a thin needle.
• The fluid in the washer reservoir has frozen.

We repair the device

In the VAZ-2107, the switches are located under the steering wheel of the car. If you suspect a malfunction, the first thing you need to do is find out the reason why this or that function does not work.

Repairing the switch

We remove the steering column switch on the seven. Having removed the first ring, then the headlight, stop and wiper levers, we get to the mechanism by which the turns are automatically turned off. We take it out and here lies the cause of all the troubles: between the reeds there is a spring that breaks off and does not move the reeds in different directions. It is necessary to replace the spring; you can use a regular spring from a ballpoint pen. Next, we begin collecting all the rings and levers in reverse order. After finishing the work, we check how the levers and the turning mechanism work. To do this, we connect the pads and place the terminals on the battery; if all functions work, then we have completed the repair.

Malfunctions of the VAZ 2107 windshield washer - causes and repairs

One of the important parts of each car is the glass cleaning mechanism, which is presented in the form of wipers and washer. Sometimes a situation arises when the VAZ 2107 windshield washer, which is designed to clean the glass from dirt, does not work. With its help, water or a special liquid is sprayed, through which dirt is removed along with the wipers. We will consider in detail how to diagnose a mechanism malfunction, as well as eliminate the breakdown.

Possible windshield wiper malfunctions

The main types of malfunctions include the following reasons:

• the switch has failed, which happens in frequent cases;
• the fuse has blown, which could have happened as a result of an overload of the electric motor, water getting on it or overheating of the wiring;
• poor circuit contact or lack thereof;
• windshield wiper motor malfunction;
• breakdown of the VAZ 2107 windshield wiper relay.

If the breakdown consists of a blown fuse, then replacing it will not be enough; it is also necessary to find the true cause of such consequences. Next, we will consider the main types of wiper malfunctions on the VAZ-2107 with a detailed description of their solutions.

How to install washing machine attachments

Nozzles for washing machines of any type can be adjusted. They are a plastic housing in which several nozzles are installed (usually 2 or 3). These attachments are spherical in shape and can be adjusted by the driver as desired. To adjust the nozzle nozzle for the washer

, it is enough to have a simple needle with which you can gently turn them in the desired direction.

If the car is equipped with three-jet injectors, there is no need to install them at the same height. It is advisable that the outermost windshield washer nozzles be directed to the lowest points. This will protect the glass from micro-scratches (which can happen if the windshield wipers are “dried out”), and the sprayed liquid will not interfere with the driver’s vision. The central washer jet should be adjusted so that it touches the top of the glass.

READ How many liters of oil to pour into a VAZ 2107

On each specific car, the driver must decide for himself how convenient it is to control the windshield nozzles. Don't neglect their settings, you just need to spend a couple of minutes to avoid visibility problems while driving when cleaning your windshield.

Related Posts

How to make distilled water at home

Where to rent or sell old tires

How to check used car advertisements

• Peugeot
• Car accessories
• Battery
• Knowledge base
• VAZ
• Generator
• Sensors

• Oil pressure sensor
• Air mass sensor
• Shock sensors
• Other sensors

#OkeyDrive © 2022 The car is simple and we will prove it. Articles on car repair and maintenance, as well as useful tips for motorists.

Unauthorized use of materials posted on the site is prohibited by copyright law. Using materials reference to the site is obligatory. Cookie Policy Personal Data Processing Policy

The cars have special equipment for driving in bad weather. The windshield of the VAZ 2107 is cleaned of water by movable brushes, and if dirty, the washer

. This device sprays a special liquid, it works simultaneously with the wipers and removes dirt.

Thus, the equipment provides the necessary visibility for the driver and passengers. This device includes the following elements:

1. Liquid tank.
2. The pump is running on board.
3. Injectors that perform the windshield of a car.
4. Pipes connecting the tank to the drives.

At the end of the summer season, the system replaces the water with an antifreeze liquid, allowing you to use the system in winter.

The windshield washer of the VAZ 2107 does not work

Cars have special equipment for travel during bad weather associated with precipitation. The windshield of the VAZ 2107 is cleaned of water using movable brushes, and in case of contamination, the washer is activated. This device sprays a special liquid, it works simultaneously with the windshield wipers and removes dirt.

The equipment thus provides the necessary visibility for the driver and passengers. This device includes the following elements:

1. Liquid reservoir.
2. A pump that runs from the on-board network.
3. Nozzles that blow a water jet onto the windshield of a car.
4. Tubes connecting the tank to the actuators.

At the end of the summer season, the water in the system is replaced with non-freezing liquid, which will allow the system to be used in winter.

Troubleshooting equipment

A failed washer that does not blow the windshield with a special liquid is restored. Most often, the injection pump needs to be replaced, which occurs in the following sequence:

1. The contact group is removed from the device.
2. Using a short screwdriver, remove the compressor from the hole.
3. In its place we insert a new unit into the tank.
4. We put connectors on the contact group, after which you can perform the test.

The engine operates with a characteristic sound when functioning correctly. The glass is blown with a water jet from the nozzles. If the tubes are replaced, you will have to wait a little time for them to fill with liquid. Using this system as intended will allow you to drive in any weather.

Windshield washer VAZ

The first VAZ models 2101 and 2102 were equipped with a windshield washer system, in which the electric pump was activated via a foot switch. On later models, for example, VAZ-21011 (21013), the pump was turned on using a lever on the steering wheel. This scheme is used today on almost all modern cars.

Structurally, the VAZ-2101 (2102) washer circuit includes the following elements:

• jet-type jets (nozzles);
• a tee that distributes liquid into two streams for the left and right nozzles;
• electric pump with switch;
• tank;
• pipelines (hoses).

Note : The electric windshield washer pump of the VAZ-2101 is made according to a non-disassembling design. If it fails, repairs are not performed. Therefore, the only way in this case to restore functionality is to replace the faulty pump with a new device.

Injectors VAZ-2101

The VAZ-2101 jet nozzle is made in the form of a cylinder with a calibrated channel inside. The liquid entering the housing is sprayed through a nozzle (spray) onto the glazing surface. At the bottom of the nozzle body there is a fitting for connecting the fluid supply hose. A sprayer with an adjusting screw is mounted in the upper part at an angle of 90 degrees to the axis of the nozzle. A plastic sleeve is placed on the middle part of the body for fixation in a special hole on the hood.

Windshield washer pump VAZ-21011 (21013)

The design of the washer system pump follows a very simple design. If necessary, you can easily cope with its disassembly and repair.

The pump is a hollow cylinder, inside of which a shaft with a rotor is mounted on a coupling. A shaft support is mounted at the bottom of the pump. A mesh filter is attached to it. An electric pump is bolted to the washer pump housing from above through the reservoir cap. A fluid supply hose is connected to the bottom of the housing. Its second end is connected to the fitting in the tank lid. Thus, the electric drive pump and the tank lid are combined into a single structure.

Why does the washer not work well?

There can be several reasons why the windshield washer fails:

• system clogging;
• clogged injectors;
• freezing of liquid;
• failure of the electric motor;
• pump failure.

System clogged

If debris gets into the tank, the system hoses may become clogged; in this case, liquid will not flow to the nozzles. To eliminate this problem, you need to rinse the tank and fill it with clean liquid.

Clogged injectors

The calibration hole of the washer jets has a very small cross-section. If debris gets in, the nozzle becomes clogged and does not allow liquid to pass through. In this case, it is necessary to remove the injectors, disassemble and clean them. The nozzles can be cleaned by blowing with compressed air without dismantling. However, you should first disconnect the fluid supply hose to prevent debris from entering the system.

Dismantling . To remove the nozzle, you must first disconnect the fluid supply hose. Then you should squeeze the plastic sleeve from below (from the side of the air intake system box). Then pry the bushing from above with a flat-head screwdriver and pull out the nozzle along with the bushing.

Note : The injector can also be pushed up by gently pressing the inlet fitting from below, after opening the hood.

disassembled in the following order:

• unscrew the adjusting screw installed in the sprayer;
• thoroughly clean and rinse all parts of the nozzle;
• we blow through the cavity of the body and the nozzle sprayer with compressed air;
• Assemble the nozzle in reverse order.

Note : When cleaning jets with metal objects (needle, pin, thin wire), do not be too zealous so as not to damage the calibration hole.

Installation . First, insert the plastic sleeve into the hole on the hood. We take the nozzle by the upper part and push it into the bushing hole until it stops. After this, connect the fluid supply hose to the fitting.

Replacement

If the old motor has failed, there is no point in trying to repair it somehow. To buy a new part, you will have to spend very little money. And the replacement procedure on most cars is extremely simple.

I will describe the main stages of work associated with replacing this element of the windshield cleaning system of any car.

• Turning off the vehicle's power. A safety measure without which further work makes no sense. Be sure to remove the negative terminal from the car. It's simple but important. Otherwise, you not only risk burning the wiring, but also getting an unpleasant electric shock yourself.
• Search for a motor. It all starts with identifying where your windshield wiper motor is located. It depends on your car. On some cars, just lift the hood and you will immediately see the washer reservoir. The motor itself is located on the reservoir (partially inside) of the windshield wiper, into which the liquid is poured. Do you see the tank? If yes, then you are in luck. If not, then you will have to look for it by removing elements of the engine compartment. On some car models, the tank is hidden so that the fender protection has to be removed.

• Disconnect the connectors with wires from the motor. Then remove the tank itself.
• The hose and fitting are separated from each other. Don't forget to drain the liquid. Filling a new one will not be difficult. Yes, and for prevention it won’t hurt to do it.
• Using a screwdriver, push the intake seal out of the bushing. This will allow you to completely remove the windshield washer motor.
• Don't forget to install a new bushing when reassembling. This often leads to the washer pump itself breaking down. So the old bushing goes to the landfill.
• Reassemble the assembly in reverse order. Here many craftsmen relax, because they consider the work done. In fact, reassembly causes more problems than disassembly. Advice from someone who made similar mistakes. That is, from me. Do not try to remember the location of parts unless you are confident in your memory capabilities. We got distracted by something, forgot, got confused. This happens to everyone, and there is nothing wrong with it. To ensure proper reassembly sequence, you can record, mark, or label the parts in the order in which they are removed. This will make it easier to put everything back together the way it was before.

The instructions are for informational purposes only, as the procedure may differ depending on the car model. Consult your machine's owner's manual for assistance. This is the best visual aid for self-repair.

There is nothing complicated in this work. Even the car owner who prefers to solve most problems with the help of a car service can easily cope with it. Repairs cost several hundred rubles and take a maximum of a few hours.

Thank you for your attention! Subscribe, leave comments, share your own experience in repairs and don’t forget to tell your friends about us! It may also be interesting and useful for them.

Windshield washer diagram for VAZ 2107 injector

I’m driving like this... with my eyes closed, because I can’t see anything anyway, but at least it’s not scary)). Now it’s quite fun for me to describe my today’s misadventures, but driving about 80 km along a wet country road, to the accompaniment of every now and then falling rain, without a windshield wiper (windshield wipers) and windshield washer was, to say the least, very unpleasant... And this is how it happened