How to attach a key fob to a Panther alarm and register the remote control

How to attach a key fob to a Panther alarm? Disarm the car and sit in the driver's seat, turn on the ignition and press the Valet button three times. After a short signal, click on the button with a closed lock on the remote control being linked. A long beep indicates that the action is correct. To exit the mode, turn off the ignition or do nothing for 15 seconds. Below we will consider in detail how to proceed to connect, how many and which transmitters can be connected to the security system.

How to register a key fob for an alarm system

If problems arise with the security system, you may need to program the Panther key fob for the alarm.

Before pairing the transmitter, keep in mind that other remote controls will also need to be configured. However, remember that each operation must be performed within 15 seconds after the last action. If this interval is exceeded, the system will exit programming, and this will be confirmed by short and long signals. In addition, when the ignition is turned off, the mode is also exited.

Now let's look at how to program the Panther alarm key fob using the example of the SLK 625, 650 and 675 security systems. To bind the transmitter, do the following:

Disable the security system and get into the car.
If the alarm does not have a code set, simply turn on the ignition.
In a 15-second period of time, click on Valet three times. The siren should sound once, followed by the LED flashing. This confirms your readiness for programming.

Click and release the remote lock key. A long beep appears to confirm the success of the step taken.
Pair the remaining remote controls. Registration of the Panther keychain (the second and subsequent ones) follows the same algorithm.

Exit programming by turning off the ignition or waiting a 15 second interval. In this case, one long/short sound appears.

The Panther 625 key fob is linked to the alarm differently if the security code is set. In this case, after step 1, do the following:

Turn on, turn off, and then turn on the ignition again.
In a 15-second period of time, click and release Valet the number of times that corresponds to the 1st digit of the code. Default is "1". After this, turn the ignition on and off.
Repeat step 2 for the second digit of the password, if provided.

All that remains is to turn on the ignition and go through steps 4 to 6 of the instructions discussed above.

Knowing how to reprogram the Panther alarm key fob, you can link an old or new alarm system transmitter.

Compatibility table

We have prepared a compatibility table for models with two-way communication, in which we indicate the compatibility of key fobs with a particular Pantera alarm model.

Attention, compatibility is indicated only for “smart” key fobs-pagers with two-way transmission. This table is not compatible with additional key fobs or tag tags!

As you can see, the table shows the capabilities of certain key fobs from Pantera and Alligator to work with alarm models. Models of security complexes are indicated horizontally, and models of key fobs with two-way communication are shown vertically. Based on the table, you can select the necessary replacement key fob both for a temporary period, for example, in the absence of original ones in stores, and for a permanent one, depending on whether you are satisfied with the functionality of a similar key fob.

The PHI-310 model, according to the assurances of many authoritative users, is a good alternative to budget alarm systems from famous manufacturers, the main difference being richer functionality and a lower price.

The main security functions of this alarm model are:

dynamic code;
anti-robbery mode with remote start capability;
car protection while the engine is running;
the ability to program an individual code for control;
active automatic security (can be configured to resume vehicle security in automatic mode);
the ability to manually set the alarm to security mode using just one service button.

In addition to these functions, the alarm system has a number of hardware locks, such as

starter blocking;
additional output for blocking relay of any other device.

This alarm is supplied in a box made of thick glossy cardboard.

Having opened the box, you can see the alarm elements, everything is packed in individual plastic packaging - this is pleasing, but, unfortunately, all the elements are carelessly scattered throughout the box and move inside it during transportation.

So, let’s look at the contents of the box, the contents are as follows:

Key fob with feedback, it has an LCD display.
Additional key fob, without feedback.
Batteries for alarm key fobs.
Valet service button.
Shock sensor (two-level).
Main communication module.
Control block.
Limit sensors for installation under the hood/trunk.
A braid of wires.
Paper documentation, installation instructions, user manual.

With security functions and equipment, everything is very clear - basic hardware locks, two-way communication, and what else can this central locking control device please car owners with.

Automatic closing and opening of doors when the ignition is turned off and on - there is, but not everywhere, a small plus in the piggy bank.

The car search function is another plus for ease of use. Trunk control from the key fob Another plus for ease of use.

In addition, the following functions are available:

silent communication control;
siren control from a key fob;
remote “turbo timer control”;
Possibility to select the sound of the alarm.

In general, this alarm makes a positive impression; it has all the basic security functions and locks, as well as rich functionality.

How many key fobs can be registered

Before programming the Pantera key fob, decide on the maximum possible number of transmitters. According to the rules, you can link no more than four remote controls. A maximum of two devices with five and the same with four buttons. In this case, the codes of previously linked key fobs are erased, and you will have to configure the Panther alarm remotes again. How to do this correctly is discussed in the instructions above.

Programming Pantera SLK-75SC

In order to program the Pantera SLK-75SC you need to follow the instructions:

Disarm the system.
Turn on the ignition.
Press the Valet button the number of times corresponding to the selection of the desired mode in the table below.

Press and hold the “Valet” button until the siren beeps.
While continuing to hold down the Valet key, press button 1 for mode 1-2 or give any signal if 3-6 is activated.
Turn off the ignition

Can any keychain be attached?

Many questions relate to choosing a suitable transmitter. Do not rush to configure the Panther alarm key fob until you determine its compatibility. To obtain information, you can contact the seller of security systems or the service station where installation is carried out.

It is best to bind a remote control that is fully compatible. Most often, such devices have a completely identical design or a slightly modified design. In this case, all functions will work correctly.

An alternative option is to register the Panther QX 270 alarm key fob or another model with partial compatibility. But keep in mind that in this case only the standard set of functions can work, for example, arming and disarming. Other options (including autorun) are not always available.

The worst thing is when the remote controls are not compatible with each other at all. In this case, it will not be possible to resolve the issue and attach the key fob to the Panther alarm system at all. To avoid such consequences, it is better to take fully compatible models.

Models with auto start

Now you can purchase modern car alarm systems with an autostart function:

SLK-775RS;
SLK-868RS;
SPX-2RS;
PR-2.

These models have a whole package of added options and are considered the most reliable in terms of signal encryption and code reading.

Model capabilities and modes

Alarm system SLK-775RS is the most simplified option. It cannot be connected to the vehicle's CAN bus.

Its set of functions includes:

two-way communication;
auto engine start;
turbo timer;
protection against signal interception;
preventing scanning;
disabling the alarm system in two stages.

But the SLK-868RS model is an option adapted to any type of gearbox. It has the function of integrating control of engine operation by speed and oil pressure. To protect the code from attempts to read it, it uses a dynamic channel encryption method and doubled frequency, which increases the range to 2 km and significantly reduces interference.

SPX-2RS protects against hacking and code-grabbing due to the simultaneous operation of two interactive and redundant communication channels.

Other features include:

reprogramming of additional channels;
connection to CAN bus and immobilizer;
7 security zones;
two-way communication;
Panic mode;
driver call function;
control via GPS and GSM;
two-stage disabling of security.

Model PR-2 is the most modern version. By using modern interactive communication channels, it makes hacking by code grabbers unacceptable.

Its specifics include:

quick response to pressing;
independent security zones;
operating distance up to 1.2 km.

Why is the keychain not registered?

There are situations when it is not possible to bind the Pantera remote control for some reason. There may be several reasons for this:

Eliminate errors in the execution of work. Once again, figure out how to set up the Panther alarm key fob. To do this, read the operating instructions for your security system model.
Check the remote control to ensure it is working properly. Perhaps it has mechanical defects or moisture has gotten inside. In this case, the alarm will not respond to signals sent from the remote control.
Reboot. The cause may be a temporary failure of the Panther alarm. Before attaching the key fob, disconnect the battery power for a while.
Move the machine out of the interference area.
Make sure the transmitters are fully compatible. Otherwise, difficulties may arise.

These are the main explanations why it is not possible to link a new or used key fob to the Panther alarm system. If you cannot resolve the issue yourself, contact a service station or installer for help.

Reviews

Vitaly, 37 years old, Samara. Pros Reliability, works flawlessly for more than a year, no problems with it. Cons The battery in the main key fob runs out very quickly.

Arthur, 31 years old, Omsk. It works and works, a solid B! It triggered falsely several times.

Konstantin, 47 years old, Sochi I agree with the above. I'm already tired of changing the batteries in the key fob, a little more than a month passes and problems immediately begin. There are few settings for the shock sensor - it works quite often, it is not clear why. There is one plus and this is functionality - you won’t find more for this money.

Why bind the remote control?

Knowing how to register a key fob for the Panther system with or without auto start, you can solve many difficulties in the operation of the device. A garter may be required in the following circumstances:

Internal malfunctions in the security system.
Mechanical damage to the remote control.
Inappropriate behavior of the Panther alarm.
The need to increase the number of working transmitters.
After resetting the settings.
Other situations related to a malfunction of the security device.

Knowing how to attach a key fob to a Panther, you can solve many difficulties in the operation of the security system. But be careful and strictly follow the manufacturer’s instructions described in the manual.

In the comments, tell us if you had to do this kind of work, what difficulties arose during the connection, and what steps allowed you to solve them.

Specifications

Panther alarm, useful information, how to install.
Panther car alarm connection diagram Pantera alarm scheme Main technical parameters of the Panther 868 alarm:

command transmission distance - up to 1000 m;
the working radius of the communicator in signal reception mode is up to 2000 m;
signal encoding type - BACS;
number of security zones - 7;
frequency range - 868 MHz;
supply voltage - up to 15 V;
operating temperature - up to +85°C.