How to attach a key fob to a Panther alarm system: register, configure the remote control

The Panther anti-theft system is very popular among car owners. It has great functionality and has various configurations that differ in price and number of tasks performed.

The owner of the Panther security system can register up to four remote controls in memory simultaneously , making its use even more comfortable and efficient. We'll look at how to attach a key fob to a Panther alarm below.

See how to find out the Panther alarm model by key fob.

How to register a Pantera key fob with feedback

Models with 2-way communication include: SPX-1, PR-1, SLK-468, SLR-5625RC, QX-270. The codes of four remote controls can be stored in the alarm memory. Turn off the security mode and follow the steps below.

Activate the ignition.
For six seconds. hold down the service key. Four CHIRPS will sound.
Press and hold the “trunk open” and “AUX” buttons simultaneously until the siren sounds once. To record a remote control without a display, use the “Trunk Opening” and “Speaker” keys.
Repeat the previous step for the remaining switches. Memorizing the corresponding key fob is accompanied by the same number of sound signals.
If no action is taken within six seconds, the control unit will exit the recording mode.
Turn off the ignition.

Instructions for setting up remote controls with autostart function

The Panther alarm system line with auto start includes the following models: SLK-635RS, SPX-2RS, SLK-675RS, PR-2, SLK-650RS, LX-320, SLK-775RS two way, SLK-868RS, SLK 625RS. You can write down the codes of four remote devices: two 5-button and the same number of 4-button.

When registering new or additional key fobs, the codes of the old ones will be deleted from the system memory. You have fifteen seconds for each operation. If you exceed the time, the control unit will exit the programming mode. Also, turning off the ignition while recording remote control codes will lead to exit from the binding. There will be one short and long squeak of the siren.

Follow the instructions to set up auto-start remotes.

Turn off the security mode, get into the car.
If entering a personal code is required to enter programming, do the following: • Turn on, turn off and immediately activate the ignition. • Within the allotted time (fifteen seconds), press the “Jack” key. The number of presses is the first digit of the code. • Enter the second secret password using the same method.
Within fifteen seconds, press “Jack” three times. The system will emit a short siren signal and the LED will flash slowly. You can enter the data of the first key fob.
Click the main transmitter button. A long siren signal will sound to confirm that programming of the first device has been completed.
Record the remaining remote controls.
The binding mode is exited by turning off the ignition or after fifteen seconds. A short and one long CHIRP will follow.

Find out what to do if the Panther alarm does not respond to the key fob.

Page 5

Attention! The text in this document was automatically recognized. To view the original page, you can use the “Original” mode.

PROGRAMMING THE SYSTEM FUNCTION

To program system functions:

1. Disarm the system and get into the car.

2. If function No. 1.8 is enabled (disabling the system using the Valet switch) - enable

combustion and go to step 4.

3. If function No. 1.8 is disabled (disabling the system using a personal code), then to enter

In the system function programming mode, you will need to enter your personal code or factory code “11” as described below:

♦ Turn the ignition on, off and on again

♦ Within 15 seconds, press and release the Valet pushbutton switch a number of times equal to

1st digit of your personal code (factory setting – 1 time), then turn it off and again

Note:

If your personal code consists of only one digit, skip the next step.

♦ Within 15 seconds, press and release the Valet pushbutton switch a number of times equal to

2nd digit of your personal code (factory setting – 1 time), then turn it off and again

4. Within 15 seconds after turning on the ignition, press the Valet button switch 3 times. You

you will hear 1 short siren signal and the system LED will start flashing slowly.

5. Within 15 seconds after the siren signal, turn off the ignition. You will hear 1 short and 1 long

siren signal.

6. Within 3 seconds after the siren sounds, turn on the ignition.

You will automatically enter Table 1 programming mode.

The siren will sound 1 signal and

The LED will start flashing single

flashes after a pause, confirming that the system has entered the 1st menu of programmable functions of the system (“User Programmable Functions”).

If you press and hold the Valet button for 3 seconds, the siren will give 2 more beeps and the LED will start flashing double

flashes after a pause, confirming that the system has entered the 2nd menu of programmable system functions (“installer programmable functions”).

7. Once you have selected the desired menu, press and release the Valet button the number of times

equal to the number of the selected function and pause. The LED will begin to flash in a series of flashes according to the function number and you will hear 1, 2, 3, 4, 5. siren signals indicating the status of the selected function. If the function number is greater than 10, the LED will flash one long flash corresponding to “10” and several short flashes corresponding to the number of ones greater than 10.

8. After the siren sounds, press the Ô button of the transmitter to turn on

selected function (siren

will give 1 confirmation signal), or press the Ô button of the transmitter to turn off

selected function (the siren will give 2 confirmation signals). If there are several possibilities for

settings of this function, then the transition between them can be carried out by successive pressing

mi buttons 0 transmitter. At the same time, you will hear the number of confirmation signals each time

fishing according to the setting you choose.

9. After this, you can proceed to programming the next function or you can exit the program.

system function programming press. Please note that the number of presses of the Valet button is “summed up” and, for example, if you have programmed function No. 1.3 and want to go to

function no. 1.12, you will need to press the Valet button 9 more times. The LED will start flashing 1 long and

two short flashes once after a pause, confirming that function No. 1.12 has been selected.

To exit

from system function programming mode:

– Turn off the ignition or

–

Do not press the key fob buttons or Valet pushbutton switch for 25 seconds
or
–

Press and hold the Valet button for 3 seconds.

The siren will emit 1 long beep and the system LED will go out, confirming exit from the programming mode.

The Panther anti-theft system is very popular among car owners. It has great functionality and has various configurations that differ in price and number of tasks performed.

This is interesting: Where is the VIN code for Renault Sandero

Recording car alarm pagers with one-way communication

The Panther security system is represented by models with one-way communication: CL-500, QX-44, CL-700, SL-600, XS2500, CL-550, SLK-25SC. The binding of the remote controls of these models to the system is carried out according to an algorithm.

Fifteen seconds are allotted for each operation.
Turn on the “Disarmed” mode. Get in the car.
Activate, deactivate, turn on the ignition again.
In the allotted time (15 s), press the “Jack” button three times. The system will emit one short siren signal. The LED will flash slowly. The signal is ready to record remote controls.
Press and hold the “Lock Lock” key until the siren beeps for a long time. The LED will remain lit continuously as long as you keep the button pressed.
Release the "Lock" key. The LED will flash slowly. The system is ready to record the next switch.
Register the remaining sensors in the memory of the security system.
To exit the recording, turn off the ignition.

Mazda Demio 2002 l. With. — electronics

Omsk

Mazda Demio, 2000

195 000 ₽

Tomsk

Mazda Demio, 2001

172 000 ₽

Barnaul

Mazda Demio, 2001

189 000 ₽

Novosibirsk

Mazda Demio, 2001

110 000 ₽

See more cars on Drome

Participate in the discussion can only registered users.

Firmware and reboot of the Pantera XS-110 remote control

You have replaced a non-working Panther XC 110 pager with a new one. How to properly connect it to the system?

Disarm the car.
Turn the ignition on, then immediately turn off.
Complete the next step in five seconds. Press the "Jack" key 5 times.
5 CHIRPS will sound and the lights will light up five times. The programming mode has turned on.
Complete this step in ten seconds. Press the left key of the first device. A single siren sound will follow.
Do the same action with the remaining transmitters. The siren will sound the appropriate number of signals.
After entering the code for the fourth remote control or turning off the ignition, the system will exit recording. The siren will sound 5 beeps and the lights will flash five times.

Video

A malfunction of the car alarm or problems with the key fob, for example, its loss or damage, lead to the need to bind a new transmitter.

Each security system supports several key fobs, usually not exceeding 4-5 devices. Therefore, the need to update the firmware of a new transmitter may also arise due to an increase in the number of connected devices. The sequence of actions when programming a car alarm depends on the model of the security system.

Features of the alarm CLK 355 375 455

These are budget alarm models of the Pantera brand. To record key fobs, do the following.

Remove the security mode.
Turn the ignition on and off within five seconds.
Press the jack key three times. Do it in five seconds. One long siren sound will sound.
Activate the ignition. 1 short and long CHIRPS will follow. The LED will flash slowly. The system is ready for programming.
Within ten seconds, click on any key on the first key fob. The system will emit one long beep. The main pager code is stored in memory. The LED will light up continuously.
Carry out the same actions with the remaining remote controls.
After entering the data of the fourth key fob, the control unit will exit the recording mode. A short and one long siren sound will follow.

Procedure for activating SLK-35SC switches

Security system transmitters use a dynamic code. In some situations, the codes of the remote control and the control unit become desynchronized. For that. To fix the situation.

Approach the car.
Double-click the button on the transmitter. Synchronization will be restored. The switch can be used.

The instructions are universal, suitable for programming key fobs SLK-100SC, SLK 4I, SLK-200SC, SLK 7I, SLK-5I.

Find out how to register your Pandora DXL 3000 key fob.

What to do if a malfunction occurs

As with any technical device, malfunctions can sometimes occur. Let's consider several possible situations of this kind.

The range of the key fob is very important for the safety of the car. If it begins to rapidly decrease, then something needs to be done about it. In this case, the most likely cause is a dead battery. This is a possible, but not the only reason.

In order for the security system to recognize the key fob, it needs to “remember” about it, remember its data. To correct this, you need to carry out the procedure for initializing the key fob data, which is described in the operating instructions.

If the key fob stops working due to a discharged car battery, due to possible sudden exposure to an electromagnetic field or due to very low temperatures, then its operation may change unpredictably, first you need to make some attempts to correct this situation. To do this, it is necessary to carry out an emergency shutdown and, having driven some distance, check the operation of the system. Sometimes repeatedly pressing the key fob buttons can help.

If the malfunction continues to occur, then the next step is to disassemble the key fob. It needs to be unscrewed and checked for dust and dirt and for the integrity of the contacts. It is also possible for liquid to penetrate into the key fob. You need to clean it and check the health of the system.

Differences in adaptation of pagers SLK-75 SC and SLK500

You can program 85SC, 755RS according to the following instructions.

The control unit's memory stores the codes of four key fobs.
You are given fifteen seconds for each operation.
Disarm the car and get into it.
In the allotted time (15 s), press the “Jack” button three times. A short siren signal will sound. The LED will start flashing slowly. The system is ready to record remote control codes.
Press the button on the first key fob. A long CHIRP will sound. Synchronization of the communicator is completed.
Program the remaining transmitters using the same algorithm.
To exit recording mode, turn off the ignition or do not perform any actions for fifteen seconds.

Security system programming

In order to correctly configure the security functions of the system, you need to program some of its functions. When purchasing a Panther, there are preset parameters described in the operating instructions. Perhaps this will suit you. If not, you will need to enter programming mode. Let us briefly describe how this should be done.

Initially, you need to turn off the security system and get into the car.
Using the Valet button, additionally make sure that the security system is disabled.
Enter your personal code to access programming mode. It is issued upon purchase of the system and can only be entered once.
Start the car, turn off the ignition and press the Valet button as many times as the first digit of the security code. Try to meet the allotted time. If the code consists of several numbers, then you need to enter them too, not forgetting the need to adhere to a strict time schedule.
After entering the program, you need to press the Valet button three times. After this, a beep should sound and the system indicator light should start flashing.
After this, you need to turn on the ignition or do nothing for a while until a signal sounds (one short and one long beep). After this, the system will go into security mode.

How to set the time on a Panther keychain

Correct display of the current time on the remote control screen is very important. After all, the clock turns on and off the most important functions: timed autostart, turbo timer, etc. The following instructions will help you set the clock correctly.

To enter the setup mode, hold down the F key for five seconds.
The key fob will emit two short beeps.
The watch face data will flash on the screen.
Using the “Trunk Opening” button we increase the clock value. Use the “Star” key to decrease the readings.
To set the minutes, briefly press the F key.
By clicking “Open trunk” we increase the minutes value. Use the “Star” button to lower it.
Hold F for five seconds to exit time setting mode.