How to cancel Starline autostart

The StarLine A94 alarm system, equipped from the factory with a 2CAN module, is the best price option for cars with digital buses, with the exception of those where the body wiring is based on LIN. But since such cars are in the minority, there is no point in focusing on them. The number “9” in the marking indicates support for A94 autostart, which is implemented using an external power control module. However, it can also be used on cars where autostart does not require duplication of power circuits (the “Start-Stop” button is used or the ignition switch serves as a low-current switch, as on the Renault Megane III).

"Starline A93"

In terms of price-quality ratio, the A93 system is in the lead, which quickly gained popularity among domestic consumers. It is equipped with a siren, which you can read about in the instructions.

This is an alarm system with feedback and auto-start, which has 5 full modes, which are conveniently configured using a key fob.

The main device for use is a keychain with a little finger battery, which is enough for 1 year of operation. There are “open-close” and “move” buttons.

The alarm unit looks almost the same in all models. There is an antenna with a built-in tilt sensor. The kit includes a spare key fob without feedback that allows you to control the alarm. There is an emergency shutdown mode for the security function. The full warranty for the installation and operation of such an autostart on Starline is up to 3 years.

Owner reviews

I drive a VAZ 2107. I chose the alarm based on price, as well as the presence of additional qualities. I don’t think that VAZs are being stolen from anyone now, so the main emphasis was on the convenience of the alarm. The choice fell on Starline B9, which, in addition to security functions (very good, by the way), can also boast additional autostart options and a decent price. The alarm has been on the car for a year now – no glitches and working properly, so I’m happy.

I’ll say right away - I bought it at the price of Starline B9. As for me, 4 thousand for a budget alarm system, but with good options, is quite good. It was recommended by a neighbor in the garage who uses it all the time, and especially praised the turbo timer, so I took it. It won't hurt me on diesel either. So far, the system has been working properly for six months, although I was a little afraid that I had screwed it up, because I installed it myself, and for me this was my first experience. But no complaints. The only drawback is poor sensitivity to the signal from the key fob. Already from the balcony of the 9th floor the car is not reachable, which is inconvenient. But the rest is all good.

Matching module

How to enable auto start on the Starline A91 alarm system? The model is more expensive in cost. To connect any alarm, you must use a matching module. What it is?

All modern cars have digital wiring arranged using analogue systems. A fee is used to coordinate it with the vehicle. In new car models it is already installed, but in earlier ones you need to install it yourself.

For normal use, knowledge of its purpose is not necessary.

Remote engine start

The Starline B9 alarm system offers several options for remote engine starting. For example, a car owner can perform this procedure directly from the key fob - all that is required is the manipulation of the keys, which are described below.

Also (if there is an optional GSM module), the owner has the opportunity to start the engine using a command sent from the phone or via SMS message. To do this, you will need to purchase an additional SIM card, which will be installed in the car. She must receive calls, decipher messages and issue appropriate commands to control mechanisms.

Mobilizer module

To install an alarm system on a modern car, you need to install a bypass and mobilizer module, which looks like an antenna with a box. Either a key clone chip or a second key is installed in it. It is not active, but is activated only at the time of autostart.

The antenna transmits a signal to the standard mobilizer and helps the car start. Since everyone has Android-based mobile phones, it is convenient to control alarms using a GSM system. This is car alarm control from a phone application. It is absolutely free to download via the Internet and allows you to control the alarm system.

The GSM board can be inserted into the alarm unit along with a SIM card, which will ensure full control of the system from the phone and receiving messages.

This will increase the range of the alarm. The application will be displayed on the desktop of the mobile phone. Agree, very fast and convenient. There is no need to carry additional devices.

From your phone you can configure all launch modes, set a timer to select the time it takes for the engine to warm up, and set the launch at a certain engine temperature.

This module is purchased separately. It will help protect your car from intelligent hacking.

Gain function

Starline has additional A95 security equipment, which is equipped with a wireless locking relay, buzzer and tags. This is a full-fledged security device that blocks one of the car’s circuits. Without a tag in the cabin, the car will not go anywhere.

Depending on the car model, different tags can be installed. You can wear them in documents. If you forget the tag at home, the car will begin to warn you about this with a sound signal. The system will always search for the tag.

There are several modes of using such a device:

When the tag search is always carried out.
For a one-time tag search when disarming for the first time. The tag will no longer be searched.
Service mode, when even during the repair process at the service center it will not be noticeable that a mobilizer is installed.

In addition to the mobilizer, you can also install a hood lock from Starline. Such an electromechanical device works in parallel with the mobilizer, preventing the lock from being unlocked without the owner’s permission.

A full-fledged security complex consists of:

security system;
mobilizer;
hood lock.

You can also use search beacons M15 and M17 from Starline. M15 is an autonomous beacon, a search device that helps find a missing vehicle. Serves for monitoring to track the speed and direction of the vehicle on the map.

Setting up autostart - how the key fob buttons work

Many car enthusiasts do not understand how to enable autostart on Starline. Let us consider in detail the sequence of such actions. To begin with, it is important to figure out how to correctly determine the duration when pressing a button, carrying out the autostart order on the Starline E91.

When the button is pressed briefly, the action continues for up to 0.5 s. If you press for a long time, you must hold the button until the sound signal appears. Double tapping is an action performed twice.

With sequential pressing - when you press long the first time, and short pressed the second time.

If you press the right button once, it determines whether the security mode is turned on. Has sound confirmation. If you want to do without sound, press long, then short.

The second button works similar to the first. If you press the button 2 times, an additional shock sensor starts to work.

The third button, when pressed once, will tell you about the status of the alarm and the temperature in the cabin. By pressing 2 times, the engine temperature will be known. You can activate an additional channel; if you press it for a long time, programmable operating modes will be activated.

After a short press, the cursor moves to the desired icon.

Autorun capabilities

List of programmable functions:

A mode that allows you to autostart from an alarm clock.
By timer - a type of periodic launch with an interval of 2 to 24 hours, depending on the need for selection.
By temperature - if the engine began to exceed the established threshold in temperature indicators. Then it will warm up automatically.
Anti-theft mode.
Turbo - to maintain engine performance for a certain period of time after the ignition is turned off. Suitable for vehicles with a turbocharger.
Auto – automatic arming 10 seconds after all doors are closed.
Mobilizer mode – blocking after turning off the ignition.

The sequence of pressing the key fob buttons

A long press on one and a short press on two starts the silent security mode.

Pressing buttons 1-3 will enable autorun. If you press 3 again, you can extend the time.

How to enable autorun on Starline? When buttons 1 and 2 are pressed simultaneously, the “Anti-robbery” mode is activated.

If you press buttons 1 and 3 simultaneously, the key fob itself is blocked, and after pressing buttons 2 and 3 this function is disabled. After a long press on button 3, you can set the alarm time, activate or deactivate the timer.

Setting the time on the key fob

To set the time on the key fob, you need to press and hold button No. 3 with the image of a snowflake until sound signals follow:

one melodic;
one short;
two more short ones.

Sound signals notify the user that the key fob is ready to adjust the time.

Current time. First, set the “clock” field, which flashes on the display. Each press of button No. 1 with the image of a closed lock increases the time by one hour, and each press of button No. 2 with the image of an open lock decreases it.

When the “hours” field is filled in, proceed to setting the “minutes” field. To do this, briefly press button No. 3 (snowflake) - the “minutes” field begins to blink. Again, use button No. 1 (lock) to increase the time by one minute, and use button No. 2 (open lock) to decrease it.

Alarm. After the minutes are set, press button No. 3 (snowflake) and proceed to setting the alarm clock. When the “alarm clock” field flashes, use button No. 1 to increase the time again, and use button No. 2 to decrease it, if necessary.

The next short press on button No. 3 (snowflake) allows you to turn the alarm on or off. Button No. 1 (lock) turns on the alarm, button No. 2 (open lock) turns it off.

Timer. If you press button No. 3 (snowflake) again, a field for setting the timer will appear on the display. Just like the clock and alarm clock, the timer is set using buttons No. 1 and No. 2.

By pressing button No. 3 again, you can switch to the mode of enabling or disabling the timer. Button No. 1 (lock) turns on the timer, button No. 2 (open lock) turns it off.

Programming key fobs

How to set up auto start on the Starline alarm system? The new key fob must be programmed. You can have no more than 4 key fobs per car. Find the protrusion of the service button in the car interior and press it seven times when the ignition is turned off.

After turning it on, a signal will sound seven times. Using the key fob, press buttons 2 and 3 while holding them, and this device will be programmed. If it is lost and you need to turn on the security mode when the ignition is on and the door is open, press the service button 3 times, turning off the ignition. The alarm will beep.

After you close the door, the system will lock after 20 seconds. This is a very useful feature in case you lose your key fob. Knowing how to enable autostart on the Starline A91, you can program several key fobs.

Factory reset

To reset the Starline A91 alarm settings, use the following algorithm:

turn on the ignition and press the service button located in the car 10 times in a row;
turn off the ignition, and the siren will emit 10 short signals, notifying the user that he has switched the alarm to reset mode;
press the service button once, after which one siren signal sounds;
press button No. 1 (lock) on the key fob, after which the system notifies with a short single signal that the factory settings have been reset;
To exit the reset mode, turn on the ignition or wait until the system automatically exits this mode. As confirmation, the side lights flash five times and the key fob emits a melodic signal.

All. The alarm has been reset to factory settings.

Thus, the Starline A91 alarm system can perform automatic functions, or it can perform mechanical functions, configured by pressing buttons. A significant part of its functions are changed by programming. Therefore, by customizing the system, you can create a convenient and reliable anti-theft system that will serve you for a long time and without failure.

The dialogue encryption method, reliably protected from the reading devices of vehicle thieves, is the main feature and advantage of the Starline alarm system. However, the alarm system, which is popular among domestic motorists, has a number of additional functions. In particular, auto start, all the delights of which can be fully appreciated in the harsh winter. Let's figure out how to enable autostart on the Starline alarm system from a key fob - remote control (RC), as well as using a special application for smartphones. Let's find out why autorun doesn't work. Let us shed light on other issues directly related to this topic.

Fact. All models of the Starline security system are equipped with a self-diagnosis function. If any element of the system fails, the car owner will receive a corresponding notification on the key fob.

How to program security and service functions

There are standard tables - instructions on how to install autorun on Starline. For example, function 9 allows you to turn off the alarm without a key fob. This is an algorithm that allows you to find out how to disable autostart on Starline in an emergency way without a personal code, with a single-digit, two-digit and four-digit code. When choosing options with entering a personal code, the inscription “PIN code” is displayed on the key fob.

To enter programming menu 1, you will need to press the service button 5 times, then turn on the ignition. Wait for the signal five times. Press 9 times. This will be a hint on how to turn on autostart so that the Starline A91 alarm system starts working. After 10 seconds, you will need to press button 3. This will allow you to read the result on the display. The two-digit pin code is now activated.

You can reset all factory settings by pressing the service button nine times, turning on the ignition and waiting for 9 siren signals. After pressing button 1, all factory settings will be reset.

Results

When the cold weather comes, many drivers are interested in turning on a system such as remote auto engine start or starting in accordance with temperature indicators.

Starline alarms can cope with this function, provided that such a system is properly installed and configured.

For many motorists, information regarding enabling and configuring autostart for their vehicle is not available. There are several reasons for this - a new or leased car.

After reading the article, you can easily ensure that the engine autostart is turned on using the Starline alarm system.

One of the most popular driving mistakes is ignoring the mandatory recommendations that will be required to turn on auto start and close the door of a switched off car manually using the key fob. Now car enthusiasts will be able to take advantage of the knowledge about the procedure for autostarting the Starline A91. The question of how to make autostart on Starline will not be a mystery to them.

Mobile app

For the convenience of users, Starline has released a mobile application for devices running on the Android platform. Through it, you can remotely start the engine or turn off the engine, set the autostart time, and also turn on the “anti-robbery” mode or set the volume of the signals.

With the help of such a program, managing the alarm system and using Starline 93 autostart is much easier. The interface is convenient and understandable for any user level.

Problems with autorun

How the engine is started in the standard wiring also determines how to connect and configure the alarm. The simplest option is a power ignition switch: in this case, the input of the autostart module is connected to the general input +12 on the lock, the outputs duplicate circuits including accessories, ignition and starter. If necessary, connect the standard immobilizer crawler, controlled by the pink wire of connector X1 on the StarLine A94 central unit.

The operation algorithm of the power module with this connection is simple, and in cases where StarLine A94 autostart does not work, this is often due to incorrect immobilizer crawler settings or incorrect detection of engine speed.

The first option is typical for cars where the immobilizer chip is polled not once when the ignition is turned on, but constantly at certain intervals: this happens on the Citroen C4, where the absence of a chip in the reception area of the standard antenna is automatically perceived by the system as the ignition key being pulled out. In this case, the car either does not start, or starts and immediately stalls. On such vehicles, the control channel setting changes as follows:

We enter the alarm settings menu by pressing the Valet service button 5 times with the ignition off. In StarLine A94 with firmware N2 and later, the button on the antenna module can also be used for this. Turn on the ignition.
The screen of the main key fob will display AF. Press button 3 to move to SF.
Long (until beep) and then short press 3 to enter the SF menu.
By pressing button 3, go to function 13, which controls the crawler. Press button 1 to set it to value 13-1 if you are not using a turbo timer, or 13-3 if you are using a turbo timer.
Turn off the ignition.

Problems with reading the number of revolutions occur if the installer used an analog control method; the current firmware does not allow reading them from the CAN bus. Moreover, a cold engine starts normally, but after running for a while, it stalls: at low speeds, the alarm cannot correctly read the analog tach signal. While the cold engine is running at high speeds, the tach signal is recognized, and when the speed drops to normal idle, the alarm system perceives this as the engine being turned off and automatically turns off the ignition and the A94 autostart does not work. To check that the speed is determined correctly, start the engine and, when the speed drops, press button 3 of the key fob - if the animation of smoke from the exhaust is not visible, then the alarm does not “see” the fact that the engine is running.

Common problems with the Starline alarm system and solutions

The owner of a brand new vehicle, straight from the assembly line of a car factory, strives to install the most advanced alarm system. For various reasons, the car owner is faced with the fact that the autostart on the car’s security system does not work. For example, during the autostart process, the engine does not start or starts running and immediately stalls. The solution to the problem is as follows:

it is necessary to install a factory immobilizer bypass module;
check the location of the key (transponder) in the bypass module;
correctly connect the wire for monitoring the functioning of the motor.

Vehicle with manual transmission – auto start has stopped working (the engine does not start after 4 attempts). The reason for the failure is that the selected connection algorithm does not work. We fix it in the following ways:

start the engine and raise the handbrake lever;
with the engine running, remove the key from the ignition switch;
open and close the door on the driver's side (the other doors of the car must be closed), set the security system.

Simultaneously with the activation of the security system, the car engine stops working, and two icons appear on the LCD screen of the key fob - “lock” and “siren”.

Manual control of autostart Starline A94

The main way to control autostart, which is most often used, is to force the engine to turn on using a command from the key fob. To do this, you can use two methods:

Long press button 1 of the key fob, after the sound signal - briefly 3.
Place the cursor on the key fob screen on the icon that looks like a fan and press button 3.

After this, the standard pre-launch cycle will operate, then the motor will begin to operate with a countdown timer. The duration of continuous operation of the motor is set in the autostart settings menu - if the time is set to 10 minutes, the indicator on the key fob will start counting down from 10. If necessary, extend the operation of the motor by resetting the countdown timer, the key combination is the same as for starting.

If your alarm system has a GPS/GSM module installed, then use the mobile application - press and hold the “engine” icon on the main screen.

How to turn off the Starline warm-up (if business has forced you to postpone the trip, and there is no need to force the engine to work in vain)? The combination to turn off the engine looks like this:

Long press button 1, then short press 4.
Place the cursor on the same icon that we indicated above, but press button 2.

Both methods are equivalent, regardless of how the engine was started, use either one.

Autostart based on temperature and time

However, there are more convenient ways to control autorun. On diesel engines, which consume practically no fuel at idle, the best option for autostart is to independently maintain the temperature. In this mode, the alarm constantly polls the engine temperature sensor and, as soon as it drops below the set value, starts the engine for the time specified in the settings. When the engine stalls, the same cycle starts again, and after cooling to the limit temperature, the StarLine A94 will autostart again.

To enable periodic autostarts based on temperature, place the cursor on the “thermometer” icon and press button 3. A melodic signal will sound and the screen will display the current temperature at which autostart occurs. Now, if necessary, you can change it by short presses of button 3; the permissible range is from -3 to -27 degrees.

You can run the engine cyclically and on time to prevent the car from drying out overnight. The principle of operation is the same, but the cursor is placed on the “alarm clock” icon. After briefly pressing button 3, the screen will display the current value of the time interval through which startup attempts are made. Short presses of button 3 change this interval from 4 to 24 hours.

However, the cold weather passes over time. How to disable timed autostart of Starline A94 if it is no longer necessary? Move the cursor over the “alarm clock” icon and press button 2, similarly with temperature triggering - only the “thermometer” icon is used.

This is where the benefits of telematic alarm control come into play: to manage these parameters, go to the settings menu of the mobile application.

You can immediately set a set of conditions: for example, periodic startup every 4 hours if the temperature is not higher than -3 degrees. Compared to programming autostart conditions through the main key fob, this is both faster and more intuitive.

Something else useful for you:

Video: How to start and stop a car engine using the STARLINE A94 key fob

Installing a security system allows you to introduce additional functions that simplify the operation of the car. The user can force start the power unit or turn off the car from the Starline A93 key fob after autostart. Alarms also allow you to control the operation of the power unit using SMS messages or a mobile application installed on a smartphone.

How to enable auto start on StarLine B9 alarm system

In order for the autorun function to work correctly, it is necessary to take into account some points during installation. For example, cars with manual transmissions are connected according to a certain scheme, for which you need to cut the black loop in the 18-pin connector of the central control unit. If the car is equipped with an automatic transmission, it remains untouched.

tighten the handbrake;
after this, you need to close all the doors and press key 2. Now the car will blink once with the side lights, the key fob will play a melody, and the screen will display the inscription r99 or r01-04 (in the case of a connected turbo timer);
We take out the ignition key, get out of the car and close all the doors. The motor remains running;
Now button 1 on the key fob is pressed. The car beeps once and its headlights flash. The central locking is also locked. The key fob emits one signal, and icons with a lock symbol appear on the screen.

The engine is now prepared to start automatically when a certain key combination is pressed.

Preparing for launch

Preparation for automatic engine start using the Starline A93 complex involves programming the operating mode (using the remote control). Additionally, a number of actions are performed to ensure that there is no kinematic connection between the motor flywheel and the drive axles. The machine is installed in a ventilated area in accordance with the recommendations given in the technical documentation for the alarm.

Engine with manual transmission

On vehicles equipped with a manual transmission, the shift lever must be in neutral position. The method of neutral installation depends on the programming of the complex’s processor unit. The final result of the algorithm is to turn off the transmission, which will ensure the safety of Starline autorun.

Supported primary programming techniques:

tighten the parking brake lever and then turn off the ignition (automatic algorithm);
turn on the brake, and then press the button located on the remote control (without unlocking the doors);
activate the handbrake (simplified algorithm).

User manual

According to the operating instructions given in the service manual, in order to use all functions of the system, you must first bind the key fob to the microprocessor unit.

Principle of operation

This function on cars works as follows:

A remote start command is sent from a mobile device or remote control to the microprocessor module. If a pre-start heater is installed on the machine, this device is activated.
Fuel begins to flow into the engine cylinders. If the vehicle is equipped with an immobilizer, then it must have a bypass unit installed. It receives a signal from the microprocessor module.
The alarm control unit carries out a pre-start check of the machine's electrical network, as well as all electronic devices for operability.
The ignition system is activated. A combustible mixture begins to form in the cylinders of the internal combustion engine, taking into account the proportions.
Power is supplied to the starter mechanism. Its contacts are closed, as a result of which the power unit starts.
If the engine does not start, the system will make several more startup attempts.
When the startup procedure is completed successfully, a message about this will be sent to the car owner’s key fob.

Purpose of the buttons

The designation of the buttons on the control key fob is shown in the photo:

Identification of pager controls

Key 1 of the communicator is intended for:

activation of protective mode with sound signals - single click;
turning on the security function without sound - successive key presses;
activating or disabling the impact controller by levels by double-clicking “can”;
closing the door locks when the ignition is activated is performed by pressing the “will” button once.

Key 2 is used for:

disabling the protective function of the car with or without sound, in the first case the press should be single, and in the second - sequential;
deactivating or enabling an additional controller by levels, for this use a double click;
opening door locks with the ignition activated, pressing must be single;
deactivating the anti-robbery mode, in this case the click must be double;
interrupting the playback of alarm signals by the siren, also one click.

Key 3 is for:

monitoring the state of the anti-theft system, as well as the temperature in the car interior, for this a single click is made;
activating the search mode and monitoring the temperature level of the power unit (press the button twice);
turning on an additional third channel, for this purpose a sequential click is made;
other options, including auto start, engine blocking, service maintenance, turbo timer, automatic activation of security - options are selected by long pressing the cursor;
enabling the function of setting time parameters, timer, alarm clock, as well as activating and deactivating these settings.

Consecutive button presses:

if you click on the first and second keys, the silent protection function will be activated;
the first and third keys will allow you to start the internal combustion engine or extend the operating time of a running power unit;
successive clicks on the second and then the first keys will activate the protection of the car with the engine running;
pressing the second and third buttons will stop the power unit;
Clicking on the third and first keys will activate the additional first channel;
buttons 3 and 2 - turn on the second additional channel.

Icon designation

Description of the icons on the pager screen:

The function of remotely starting the car's power unit using an alarm clock is enabled.
The remote start mode of the power unit by timer is activated.
The option to remotely start the internal combustion engine in accordance with temperature indicators has been launched.
The option for servicing the anti-theft complex using the Valet key is enabled.
The turbo timer function of the power unit is activated.
The automatic security mode is enabled.
Engine immobilizer activated.
The option to block the buttons on the pager to control the security system is enabled.
A symbol that determines the temperature level of the car engine.
Power supply charge indicator in the communicator. If one division remains on this symbol, the battery must be replaced.
The car engine is started.
The anti-robbery option is enabled when a car is forcibly seized.
An auxiliary satellite unit Starline M20 or M30 is connected to the anti-theft complex.
The trunk of the car is open.
The indicator warns the car owner that one or more car door locks are not locked.
A symbol indicating that the hood of a car is open.
The anti-theft system informs the car owner that the sensitivity sensor, one of its levels, has been activated.
Current time board.
A timer option is included for remote engine start.
The alarm is activated.
The icon that determines the connection between the control panel and the main electronic unit of the system is made in the form of an antenna. If there is one line next to it, then the connection between the key fob and the module is weak. If there are no divisions, the remote control is out of range of the antenna control unit.
If this icon is not lit, this indicates that the locks on the car doors are not locked.
Closed car doors.
The car protection function with sound is enabled.
The vehicle's silent security mode is activated.
With this indicator, the anti-theft system indicates that the parking brake lever is not raised. As a result, remote start of the power unit is impossible. This indicator may indicate that the brake pedal is depressed.
This icon informs you about setting up a personal code to turn the alarm on and off. The password itself can contain from 1 to 3 characters.
The indicator informs about the activation of the internal combustion engine remote start function on a car equipped with a manual transmission.

Arrangement of symbols on the communicator display

Channel “Crossover 159” talked about the functions of the Starline key fob, as well as the indicators on its display.

How to start a car with a Starline key fob

To start the power unit using the key fob of the A93 or E91 complex, you will need to press and hold down the first button (used for arming). The remote control buzzer will sound a melodious sound 2 times, external lamps on the machine will work, and a siren will sound. The key fob will play the melody again and activate a text notification on the display. After the power plant starts operating, the display shows the remaining time (preset) and an icon simulating exhaust gases is active.

On the A91 complex, equipped with a 3-button remote control, you need to press the security button for a few seconds, and then briefly press the button with the asterisk sign. The status signal diode included in the design will switch to constant operation mode, and a text message will be displayed on the panel display notifying that the motor shaft is cranked by the starter.

Using an additional key fob

You can start the car from the A93 or E91 alarm remote control, which is not equipped with a display, by pressing the security activation button (holding the key for 2-3 seconds). The further algorithm does not differ from the method using a remote control with a screen. If the main key fob is in the signal reception area, then the display will display an icon indicating that the power unit is running. On the A91 complex, it is impossible to start the engine using the auxiliary control panel.

Through the key fob tag

You can start the car using the key fob after programming the complex in Slave mode. An additional key fob is used as a tag; the function is available for alarms that can work with the standard vehicle system (A93 or E91). After a short press on the security button (while pressing the small key located on the other edge of the case), the red diode turns on, transferring the tag to the standard operating mode. The engine is then started by long pressing the button.

Using a mobile call

The user can start and stop the motor using a voice message, which is sent to a separate unit in the alarm. The number recorded in the module is registered on the website of the security system manufacturer.

The user connects to the alarm and then selects the required command from a list dictated by the answering machine.

The command is pronounced by voice or activated by buttons on the phone keypad.

Via SMS message

Starting the engine from the key fob is performed only within the range of the remote control. To control the operation of the motor over long distances, a special add-on module is used, installed in the alarm processor unit. Inside the device there is a mobile operator card with a separate number; to start using the equipment you need to register on the manufacturer’s website.

After pairing the alarm system with the owner’s cell phone, it becomes possible to control the complex using commands sent as SMS. The user starts the motor from a distance, extends operation or stops the unit. It is also possible to receive a report on the status of the complex or the battery charge level.

Using the app

To start the engine through an application installed on a smartphone, you will need:

Install an additional expansion unit with a slot for a mobile operator card.
Activate the installed equipment according to the manufacturer's instructions. The tariff plan of the number used in signaling must support data transmission via the GPRS protocol.
Register the equipment on the manufacturer’s website, and then download the application distribution kit to your smartphone.
Pre-pair the smartphone and the security system by entering information about the type of system into the application menu and programming the number of the SIM card installed in the processor unit.
After registration is completed (accompanied by an additional email sent to the car owner's email), access to the alarm settings appears. The menu is used to start or stop the engine, track the vehicle's position or control the speed of movement.

Setting the sensitivity of the shock sensor

The security system includes a sensor that determines the force of the impact on the body. The sensor is used to activate the alarm mode, perceiving a blow as an attempt of unauthorized access to the vehicle interior. The device is mounted inside the vehicle; the operating instructions recommend placing the product open to adjust the sensitivity. There are control diodes on the body that turn on when a blow to the car body is detected.

Vibrations that occur during engine operation are perceived by the sensor as attempts at burglary, which triggers the siren. To adjust the sensitivity, 2 potentiometers are used (warning zone and alarm level), which are rotated with the tip of a screwdriver. The regulator has 10 positions; when shipped from the factory, position 4 or 5 is set. Before starting, you need to reduce the sensitivity of the device by turning the regulators to a minimum.

Then you should start setting the warning level. To adjust, you need to open the car door, activate the security mode, and then turn the adjuster screw clockwise. Sensitivity is determined by light palm strikes applied to the body. Then the user can set the alarm level on Starline (by analogy). After completing the adjustment, it is recommended to set the security system to autostart and check the sensitivity of the sensor when the engine is running and when there are impacts on the body (by tapping the roof panel with your palm).

Read also: How to degrease the surface of a car before sticking windshields

How to turn off the engine

On the Starline A93 system, it is possible to turn off the engine from the key fob by holding the arming button for a long time, after which you should briefly press the key with the circle symbol. The car will flash the external alarm lamps 4 times, and then the engine will stop. The indicators of the operating power unit on the control panel will go out, and a melodic signal will also sound. On the auxiliary remote control, to stop, sequential action is applied to the security control button and the small-sized button located next to it.

To turn off the engine on the Starline A91 model using the key fob, you will need to press the disarm button for a long time, and then briefly press the button with the star icon. After sending signals, similar to the A93 complex, the engine will turn off. An auxiliary remote control without a display does not allow you to turn off the power plant.

Causes of problems

If the car does not turn off when you press the remote control button, you need to check the condition of the battery. The problem occurs when electronic components are damaged or when using a key fob that is not registered in the complex’s memory. Identical problems occur when operating Starline A91 equipment, which has a similar design. A backup remote control is used to stop the engine. It is allowed to open a running car with a standard key; the security is disabled by entering an emergency code (without a remote control).

If the car starts up and then stalls after some time, then the functionality and accuracy of the temperature sensor readings located under the hood of the car are checked. To check the operation of the automatic start, you need to program the operation algorithm using a timer, or start the motor remotely using the remote control. If the engine stalls, then the correct installation and configuration of the complex elements is checked.

If the user plans to start and stop the power plant using a mobile application, then it is necessary to control the account balance. If there is no money, the operator blocks the forwarding of messages. In this case, the owner must either use a backup number or a standard Starline A91 or A93 alarm remote control.