Engine blocking by alarm. The alarm blocks the engine from starting, what to do. Features of the alarm system

Engine start blocking is a function that is on the list of available options in almost any anti-theft system. In this case, the system contains an immobilizer that identifies the owner by a special tag and allows the engine to start. Conventional car alarms that have a similar function in their arsenal can also block the engine from starting.

We also recommend reading the article about why the engine may have difficulty starting when hot. From this article you will learn about the main malfunctions that cause difficulties when starting a warm internal combustion engine.

According to experts who work with automotive electrical equipment, more than half of all cases of unexpected engine failures to start are directly related to car alarm malfunctions. Note that the complexity of implementing locks in this case is noticeably simpler compared to complex anti-theft solutions. This significantly increases the chances of removing the engine start lock yourself in the event of a breakdown or malfunction. Next, we will look at what the driver should do if the alarm blocks the engine from starting.

Engine blocking with car alarm

If there are installed anti-theft systems, electrical equipment is responsible for blocking the engine start.
Immobilizers or car alarms may turn out to be faulty and give constant or isolated failures during operation. It should be added that the severity of the problem will depend not on a specific model or brand of car, but on the complexity of the installed anti-theft system.

Why does the starter turn normally, but the engine does not catch and does not start? The main reasons for the malfunction, checking the fuel supply and ignition systems. Adviсe.

Accidental activation of the engine lock function

First, carefully study the displayed icons on the alarm key fob. A common reason for blocking is the accidental activation of additional functions. You also need to monitor the LED readings (if present) in the car interior, which serves as a light indicator of the alarm status. The flickering of the LED lamp almost always indicates that the anti-theft function of the immobilizer is activated in the menu.

If, after turning the key in the lock and turning on the ignition, frequent blinking of the signal lamp is observed (for example, the StarLine car alarm) before starting the engine, and a pictogram with the inscription “immo” is displayed on the key fob itself:

1. One of the methods to solve the problem is to remove the key from the lock, then just press the button to open the central door lock on the key fob.
2. You can also get out of the car, set the alarm to security mode, then disarm it and then start the engine.

In other words, you need to make sure that the alarm operates in the normal and usual mode for the owner. Up to 30% of cases of engine start blocking by alarms occur due to accidental configuration of software options. The driver’s task is to disable all unnecessary functions in the settings.

Using the StarLine alarm as an example, let us note that this system has a “two-stage” unlocking function. Activation of the function may occur by chance; a separate icon will shine on the key fob display

To turn it off, you need to hold down button 3 on the key fob. The key fob will emit two beeps, after which button 3 is pressed once again. Then button 1 is pressed for a few seconds, then the security functions are removed;

Not

the car
start ?
Not
a problem when there is a good car service center with skilled craftsmen nearby. There may be reasons.

Pre-check

Having taken the car off the road (if necessary), the first thing we need to do is make sure that the alarm is set to the mode we planned. People professionally familiar with various types of alarms assure me that a third of their engine freezes are due to accidental reprogramming. This means that your task is to remove any errors in the settings.

For example, the Starline security system has a “disarm 2 times” function. There is a separate button on the display to activate it. Accidental operation may cause the engine to seize.

To disable this feature:

How to unlock the alarm

Starline A93 - basic alarm functions
Engine blocking can be eliminated independently. If the security system does not allow you to start the engine due to complex breakdowns, you need to contact a specialist. A driver who has knowledge of the structure of automobile electrical systems and the necessary tools can unlock a car alarm. The car alarm elimination plan includes the following steps:

• Gaining access to the head unit. It is located in the left corner of the cabin. The place is inconvenient for work. Protective elements are located next to the main unit. If the car engine is blocked, work begins with checking the fuses.
• Checking electrical circuits. The standard wiring is disconnected from the security system. After this, check the cable connections. Poor insulation can cause contact failure.
• Disconnecting the CAN bus. When this part of the system is turned off, the lock is removed automatically. To do this, disconnect all terminals from the head unit.
• Checking the security system relay. They are located next to the main unit or are fixed in the cabin with plastic ties. To deactivate the immobilizer, the relay contacts close independently. The operation is performed using a multimeter. The relay cover must be removed using a screwdriver. After this, the anchor is clamped, forcibly closing the contacts.
• Checking the immobilizer bypass. Such work is performed when it is necessary to unlock a car from an alarm system equipped with auto start. The immobilizer is connected to the electrical circuit in a serial manner.

Key fob glitch

If it is impossible to start the engine with the ignition key, the reason should be sought in a faulty key fob. To resolve the problem, perform the following steps:

1. To start the engine, you need to release the ignition switch, and then activate the central locking unit. The latter is turned off and they try to start the engine.
2. If the above actions are ineffective, the ignition is turned off. The driver must leave the car and switch the anti-theft system to security mode. After a few seconds, they check whether the vehicle can be unlocked. The driver returns to the cabin and tries to start the engine.

If the alarm still blocks the engine from starting, you need to inspect the key fob and study the operating instructions for the security system. The pager may have been mistakenly set to immobilize the vehicle. In different security systems, the activation of this function is indicated by separate indicators.

Malfunction of the immobilizer or other factory system

An immobilizer is used to stop the movement of a vehicle in the event of criminal attacks. Failure of parts of the security system may make it impossible to unlock the engine from the alarm. If such a problem occurs, contact a specialist who will find the cause of the problem and eliminate it.

Cars produced in the USA and Japan are equipped with modern anti-theft systems. It is impossible to start the engine without sending commands from the key fob. Even such systems can fail, which is associated with breakdowns of the control unit. Only a specialist can remove the engine lock. Performing certain actions will cause the power device to start.

Problems with the ECU

The engine and car alarm immobilizer interact through the control unit. A sensor malfunction can result in the motor being blocked and not starting even after the appropriate commands are given. In this case, you need to test the system and eliminate errors. It is not recommended to solve the blocking problem yourself. Repairing an electronic device at home leads to the breakdown of this element. Only a specialist can remove the blocking.

Independent troubleshooting of alarm systems

Starting the engine with a button, diagram and features of self-installation

• It is often possible to fix the malfunction and remove the engine lock yourself if you can detect blown fuses. This problem often leads to malfunctions of the alarm system. The fuses must be checked; if a problematic element is detected, the blown fuse must be replaced with a known good one.
• Malfunctions in the operation of the alarm can also be associated with insufficient battery charge or loose terminals on the battery contacts. In this case, the battery is still able to sluggishly crank the starter, but the engine blocking may already work and further prevent the engine from starting.

Another step is to check the limit switches (limit switches), which are located under the hood and trunk lid. Moisture ingress or oxidation of the limit switch often causes an incorrect signal to the alarm control unit, which leads to engine blocking

Please note that unprofessional installation of alarms and limit switches, as well as improper engine washing can lead to malfunctions of electrical equipment

Problems that may arise with car alarms

How to open a car if the alarm key fob is dead

Before considering ways to turn off the alarm without a key fob on a car, you need to understand what breakdowns of these security systems exist. They are as follows.

1. The lack of a signal between the key fob and the security system unit is one of the most common problems that occurs frequently; its symptoms are that the car does not completely respond to signals coming from the key fob. There may be several reasons. There are other cars next to the car that have similar alarms, and the signal is simply jammed. If the alarm key fob has been mechanically damaged, the batteries have run out.
2. The battery is low. This problem also happens often. This results in the system not receiving enough power and simply not working.
3. Failure in the electronic system. This reason for poor performance is rare, but if this is the problem, it is better to contact specialists who will carry out the necessary diagnostics and be able to fix the problem.

Therefore, if at the most inopportune moment the alarm stops working, then the car owner should be patient and try to turn it off manually.

It is important to remember that most modern security systems have a function to block the start of the power unit. Therefore, if the alarm system fails, you will not be able to start the car; you will need to unlock it yourself, or with the help of appropriate specialists

Temperature control failure

One of the serious reasons for the lack of automatic start in cold weather or in winter frost is the failure of the temperature-sensitive system when the thermostat is correctly connected. This may be due to:

• the temperature sensor is damaged due to normal wear (replace);
• The sensor is installed incorrectly (needs to be reinstalled in accordance with the manufacturer’s recommendations);
• The engine start was not set to match the temperature shown on the communicator display.

Each of the above reasons can be detected and eliminated by the driver himself if the diagnosis is carried out correctly and consistently.

How to unlock the alarm

Autoworld

One common way to protect your vehicle from thieves is to install a car alarm. This protection system was invented several decades ago, and it successfully carries out the functions assigned to it. Previously, the vast majority of car enthusiasts relied more on IP street surveillance cameras, which they could freely order on the website, but today there is a huge selection of car alarms with various additional functions, produced by different manufacturers and in different price categories. However, a car alarm is, first of all, an electronic device that periodically malfunctions. Next, we discuss the phenomenon of blocking car alarms and provide some useful tips for unlocking car alarms.

So, let’s say that you had to face a problem in which the car alarm stopped responding to remote control presses and stopped unlocking the door locks. This can happen for several reasons. For example, the most common reason is that the battery installed in the remote control has run out. Another common problem can be a dead vehicle battery. Finally, more serious failures include a malfunction of the alarm control unit. In any case, these malfunctions require immediate intervention; thanks to the features of most car alarm models, it will not be difficult to unlock it and open the car door. It is much more difficult to unlock the engine, since electronic protection will not allow it to start.

What can you advise if you have problems blocking your car alarm?

You need to start your actions from simple to complex. First, you should replace the battery in the remote control, or use the second remote control included in the alarm kit and try to unlock the alarm with its help. If there are no results, you need to make sure that the car battery is charged. If the car alarm light does not blink, this is the first sign. In these cases, you can use the key to open the door, and if the security siren turns on, you should press the emergency button to turn off the car alarm installed in the car, called Valet. What to do if the control unit malfunctions? In this case, it is best to contact auto electricians who will either be able to adjust the unit or replace it.

After completing these simple manipulations, you can independently restore access to the machine. However, if you have no experience working with electronic devices, after you regain access to the car, contact a service station to make sure that the car alarm is working properly.

• ← Truck tractor TATA Prima 4938S
• Car engine cleaner →

Principle of operation

The engine start blocking by the alarm occurs if the anti-theft complex is equipped with an immobilizer. Often the car does not start even if there is a two-channel security system. The principle of operation of the blocker is to open the electrical circuit or supply current to elements that can affect the starting of the motor. The engine does not start or stops working after a while. The immobilizer prevents the commission of criminal acts related to disconnecting wires or disassembling anti-theft systems.

If the alarm detects a break-in attempt, it blocks all accessible components of the car. Immobilizers are activated automatically.

Methods for eliminating alarm blocking

To unlock the starline alarm you need to do the following:

• Replace the battery in the control key fob. If after replacing the battery the vehicle does not respond to signals, then you need to try to open the car using the second key fob (if it is included in the kit).
• Open the car using the key and turn off the alarm by pressing the Valet button (emergency shutdown of the anti-theft system).
• Remove the terminals from the battery. In winter, the blocking of the security alarm is often associated with a low car battery. This can be determined if the lamps are dim, the car does not start and the anti-theft system does not turn off. In this case, to block the alarm, you must remove one of the terminals. After charging the battery, it is necessary to reprogram the control key fob.
• Disable the anti-theft system. Most often, the unit is installed under the car control panel. To turn it off, you need to remove all the wires from the unit and start the car. If it doesn't start, it means some parts are blocked. To unlock them, you need to disconnect the wires going from the security system unit to the car wiring, and then connect the ends of the standard wiring together. After these steps, the vehicle should start.

Unlocking Starline alarm

What to do if you can’t start the engine

The problem can arise in two cases: a problem with the key or a malfunction of the immobilizer. We will not consider the case of the key being lost or broken; it is available, but the system is not unlocked. If you have a second copy, you can try to launch it using it. If this is successful, then the problems are caused by a faulty ignition key. In this regard, if a car was purchased with only one copy, or one is lost, it is best to take care of making a duplicate of it in advance (or another option is to make an immobilizer bypasser). Today this is easy to do; there are many workshops that, for a reasonable fee, will presence will quickly be able to produce a chipped product for your car. But what to do if the second copy does not start the car engine, that is, the systems are not unlocked? Let's try to figure out this problem. Sometimes the software of this device fails, this will require its reprogramming, or as experts also call it, reflashing this unit. The essence of this procedure is to combine the new device with the standard control unit. To carry out this procedure, you need to access these programs. This can be done using a PIN code; it is issued to owners when purchasing a car on a separate card.

But please note that a password can only be purchased once, otherwise you will have to order a new unit for your car. Sometimes you have to turn off this unit in order to be able to continue operating the machine. This operation can be performed independently only if you know how to work with the car’s electrical system, otherwise you can only harm your car. It should also be taken into account that after this the security of the car will be significantly reduced. Problems may arise if the contacts of the immobilizer receiving antenna are broken. It is usually installed around the car's ignition switch. The contact can be restored; sometimes it is enough to move the connection connector, and if oxidation has occurred, you need to get rid of it. WD-40 liquid helps in such cases. Sometimes, to solve this problem, you have to install an immobilizer bypass. This unit can be purchased in retail chains or made independently, but you definitely need a chip or a chip-based device, as well as experience in repairing electrical equipment. This is not a complete list of all possible faults and their elimination. In this article, we tried to describe the situation in accessible words and tell you what to do if the immobilizer does not see the key or does not allow you to start the car. If their use is not successful and the car still does not start, you will have to contact a specialist.

How to start the engine if the alarm does not work

Almost all modern alarm systems allow you to disable the standard security system, even if the remote control is faulty. To do this, a “secret button” is installed in the car. This button, after a certain number of presses, produces an emergency shutdown of the alarm system, including the immobilizer. This function is described in more detail in the documentation for the anti-theft system, in the section “how to turn off the alarm.” If you have a GSM security system installed, connected to the dispatch service, call the operator, identify yourself and the code word and ask to turn off the alarm in the car or disarm the car.

What to do after starting the engine

After you have successfully unlocked the anti-theft system, deactivated the immobilizer and started the engine, you need to take the car to a service center or workshop for inspection. Without this procedure, your car is defenseless against car thieves, because you will not be able to turn on the anti-theft normally and then turn it off normally. There is always a small chance that the alarm's malfunction is caused by damaged wiring or a short circuit. This may damage the on-board electronics and cause the vehicle to catch fire. Therefore, do not delay in diagnosing, repairing or setting up the anti-theft system, otherwise next time you will have to deliver the car to a service station using a tow truck.

Firmware for the new Mongoose remote control

Reprogramming the Mongoose alarm remote control switch (Pentacle M-1, 600 Line4, 900 ES line 4, 600, PS 2070, 900ES, LS 9000D, LS 7000D, IQ215, 1.7R, 1.9R, EMS 7.0, vp commodore, ems 1.7, Transponder, MX750S, MX30T with 2 buttons, MX 200, base a50 1) follow the instructions.

1. Turn on the ignition. Using the service key, enter the password (the number of presses corresponds to the PIN value).
2. Turn off the car's ignition and turn it back on immediately.
3. On the transmitter, press the first button. A short siren signal will sound to confirm successful recording.
4. To exit the setup menu, turn off the engine and press the service mode entry key once.

Disabling locks using the service button in the cabin

If there are no signs of unintentional activation of the locks, you can try to unlock the engine using the service mode. This mode is called Valet and is used to transfer the system to service mode. To activate, you need to insert the key into , turn on the ignition and then turn it off.

After this, you need to hold the service mode activation button for about 10-20 seconds. The result will be a notification using a special short signal, after which the signal lamp (indicator light, LED) will be constantly on. This method means disabling all security functions, which may also mean removing the engine locks. We add that after fixing the problem, it is necessary to activate the security functions of the alarm again.

A little about functionality

Old models (for example, Mongoose Imperium M5000), which require a standard immobilizer to ensure 100% protection, have been replaced by new products that can independently provide unprecedented security and two-way communication (Mongoose Base 20, Mongoose 600, Digital 100, Mongoose lq 200 and others).

Mongoose alarms of the modern line offer the user the most convenient and thoughtful set of options, namely:

1. Silent security mode. In this case, only light signals and a message on the pager alert you about the attempted theft (the sound is turned off).
2. Delayed security mode. The alarm will not turn on the protection immediately after pressing the corresponding buttons, but only after the trunk and doors are closed.
3. Automatic engine start. Systems with autostart Mongoose will turn on the engine according to preset parameters (at a certain temperature, at a specific time, set by an alarm clock or timer).
4. Anti-Hi-Jack mode (active, passive). Enabling this option blocks the engine while driving (this process is controlled by the owner, the mode is activated by the key fob buttons when attempting to steal).
5. Emergency shutdown . This mode allows you to remove protection from the car using a special PIN code, even if the car cannot be opened with the alarm key fob or in a situation where the control panel was lost by the car owner.

Disabling the anti-theft system without a key fob

Sometimes there are cases of loss of the Starline security system control key fob or its complete malfunction. Then you need to turn off the alarm manually, namely:

• Coded deprotection.
• Normal emergency removal.

To use these methods, you need to know exactly the location of the secret Valet button (switching the car to the service state). This button is most often located near the control levers, in the area of ​​the safety block, behind the glove compartment, near the steering wheel or under the car panel.

If you do not find the service button, then you need to contact the company where the alarm was installed or call the previous owner of the vehicle.

To disconnect a car from the security system without using a key fob, you need to use the correct algorithm. It depends on which starline anti-theft system is installed on the car. Let's take a closer look at the algorithm for unlocking the anti-theft system, depending on the model.

Starline A1, A2, A4

Disabling these security system models depends on the operating method of programmed option No. 5. If you use the shutdown method without entering an individual password, then you need to do the following:

• Open the door.
• Start the ignition for a few seconds.
• Press the service button 3 times.
• Turn off the ignition.

If you use the disabling method by entering an individual password, then you need to do the following:

• Open the door and start the ignition for a few seconds.
• Press the service button several times (the number of presses is equal to the first digit of the individual password).
• Turn off and then restart the ignition.
• Press the service button several times (the number of presses is equal to number two from the individual password).
• Turn off the ignition.

Starline A6

To disarm a vehicle on which this anti-theft system is installed, you need to:

• Open the door and start the ignition.
• Press the secret button several times (the number of presses is equal to number one of the personal password).
• Turn off and restart the ignition.
• Press the secret button several times (the number of presses is equal to number two of the personal password).
• Turn off the engine.

Starline A8, A9

If your car has an alarm system of this model, then to unlock it you must do the following:

• Open the vehicle door and turn on the ignition.
• Press the secret button 4 times within a few seconds.
• Turn off the engine.

If the programmed method is automatic arming, then after turning off the engine you need to start it again for at least half a minute, and then turn it off.

Starline B6, B9, A62, A92, B62, B92

Disabling these models depends on the state of the programmed option No. 9. If you use the shutdown mode without entering a personal password, you need to do the following:

• Open the vehicle door.
• Start the ignition and press the secret button 3 times within half a minute.
• Turn off the engine.

If the automatic arming mode is selected, then after stopping the engine you need to turn it on again for 15 seconds and then turn it off.

If you use the method of entering a personal password, you need to do the following:

• Open the car door and turn on the ignition.
• Press the secret button the required number of times equal to the first digit of your personal password.
• Turn off the engine.

If a method is programmed with entering a 2 or 3-digit password, then you need to start the ignition again and enter the necessary numbers by pressing the secret button. These steps must be repeated two or three times.

If for some reason the car could not be disarmed, then you need to contact.

Unlock methods

Having installed an external alarm system, for example, Starline, it is advisable for the car owner to carefully study the instructions for the rules of its use and operation. The instructions also contain tips on what to do if there is a malfunction in its operation.

The easiest way to unlock an external alarm is to re-close the car doors. To do this, get out of the car and close the door tightly. Then turn on the remote control to arm the car and wait about ten seconds. It is during this time that the car is armed. On some types of alarm systems, the arming process takes longer, from one to two minutes. Open the doors again using the remote control and try to start the engine. If the failure occurs due to the door switches, hood, or trunk lid, then the car will start.

An attempt to return parameters to factory settings using the key fob can work effectively. Due to the fact that there are very many types of alarm systems installed on cars, and at the same time the settings algorithm is also varied, resetting parameters and returning to factory settings must be carried out according to the instructions.

Situations arise when the central unit does not respond to commands sent by the key fob. In this case, you can use the Valet service button. The button may be located in a secluded place, where the hijacker will not find it and it will take time to find it through the wires.

The location of the Valet button is indicated in the description, but often installers choose its location at their own discretion. It is recommended that after installing the alarm, you check with a specialist in what place he placed it. Forgot to ask or bought a used car, and then there were problems with the signaling. No problem - the service button is easy to find along the wires coming from the central unit.

If the alarm system is blocked so that not only the engine does not start, but the doors do not open, then you need to open the door lock with the key. Opening the door will automatically trigger a loud sound alarm, which can be turned off by disconnecting the terminal from the battery. Using the dialing method or using a diagram, the terminal numbers on the central unit and the color of the wires are determined. Using this information or visually using wires with the corresponding color, we find the location of the button.

Switching to service mode (or unlocking) is individual for each type of anti-theft system. Therefore, how to use the Valet button is described in the manufacturer’s instructions. Basically, all actions are almost the same for most types of alarms.

Here is an example of Starline deactivation:

1. Open the car with the key.
2. Turn on the car's ignition and press jack three times (time limited to 20 seconds).
3. Turn off the ignition.
4. The siren will sound and the emergency lighting will turn on at intervals.
5. Starline deactivation is complete.
6. Start the engine.

Methods for disabling an alarm without a key fob

Professionals who have encountered such problems have developed effective methods on how to turn off the alarm on a car without a key fob. They are based on a detailed study of the instructions for such security systems.

At the moment, there are two ways:

• simple disarming, which involves manipulating a special “Valet” button;
• disarming using a special code is a more complex method that involves dialing a special digital combination.

Before considering these two methods, car enthusiasts should have an idea of ​​the button called “Valet”.

It is an important part of any security system and performs two functions. The first is that it is used to set up an alarm system, and the second provides for emergency unlocking

It is important to remember that if a car owner bought a used car, or went to specialized service stations or other workshops to install an alarm system, he is obliged to clarify where this button is installed in the interior of his car. This is necessary so as not to look for it when you urgently need to turn off the security system

Standard shutdown

The alarm can be turned off easily this way.

First, it must be said that such manipulations must be carried out quickly, since the alarm speaker will go off immediately after opening the car interior door.

After the driver gets into the cabin, he must take out the instructions and find the “Valet” button. The brochure (instructions) will indicate the sequence of turning on and off the ignition of the car, while simultaneously pressing this button. For example, the driver needs to turn on the ignition and immediately press “Valet” twice. After that, turn off the ignition and press it once, and then turn it on again and press the button once. After such manipulations, if everything is done correctly, the speaker stops working, and the car enthusiast can drive the car without any problems.

It is important to remember that the above is an approximate combination, so that any car enthusiast has an idea of ​​how manipulations to turn off the alarm occur in a simple way. But for each individual security system model, this combination is unique, so before starting work you need to carefully read the instructions

Withdrawal using a special code

If the alarm model is expensive, or it includes the latest developments, then most likely it is encrypted, and in order to turn it off without a key fob, you will need to enter some kind of digital combination.

Now let's look at how to enter the code correctly. To do this, you will also need to find the above button and remember which code was set by the driver.

The process will be as follows.

Let's look at the example of a three-digit code, it is as follows: 212. After the car enthusiast gets into the car, he turns on the ignition and presses the “Valet” button (toggle switch) twice, after which the ignition is turned off.

Then it turns on again, and the driver presses the toggle switch once, after which he immediately pulls the key out of the lock. Then a similar manipulation is repeated again, only the button needs to be pressed twice again. If everything is done correctly, the alarm will be unlocked without a key fob.

You can disarm the car from the security alarm only through a special button located in the car's interior. This needs to be done quickly, but before doing this, carefully read the instructions.

https://youtube.com/watch?v=q3olDJe_x8A

Instructions

Anti-Hi-Jack. Robbery protection The mode can be turned on and off by programming. Note: In order for Anti-Hi-Jack to be activated, in addition to software enablement of the function, it is necessary to set a two-digit PIN code for the Mongoose DIGITAL 100 system. Your Mongoose DIGITAL 100 security system is equipped with a special anti-burglary function Anti Hi-jack, which will be automatically activated if any door is opened while the ignition is on. You can also turn on Anti Hi-jack remotely by pressing button 3 for 3 seconds with the ignition on. If the function is software enabled and you are asked to hand over the keys and leave the car, simply comply with the demands of the robbers, Anti Hi-jack will turn on the alarm itself and force the robbers to stop. To ensure that the activation of Anti Hi-jack does not interfere with the movement of the car and you have the opportunity to calmly turn it off, and also to avoid creating a dangerous situation on the road, the anti-theft procedure goes through the following stages until the full alarm is activated and the engine is blocked: 1 30 second pause for entering the disabling code. After opening the door or pressing button 3 on the control panel for 3 seconds with the ignition on, the warning lights will flash once. The system LED flashes slowly to remind you to enter the disable code. 2. Warning mode. If you have not entered the disable code during the 30 second pause, the system will remind you of this with short beeps over the next 30 seconds, and the LED will flash quickly. 3. Alarm mode. At the end of stages 1 and 2, if the disabling code has not been entered, the system goes into alarm mode: a full sound and light alarm is activated. When the simulated fault lockout (SSDA) mode is enabled by software, it will turn on simultaneously with the alarm. In this case, the engine blocking will be carried out according to the following scheme: 1 second - blocking ==> 5 seconds - pause ==> 1 second - blocking ==> 3 seconds - pause ==> 1 second - blocking ==> 2 seconds pause = =>1 second – block ==> 2 seconds – pause, etc. The last cycle will be repeated until the ignition is turned off, after which the engine will be completely blocked and it will not be possible to start until the Anti Hi-jack is completely turned off. If the fault simulation lock is disabled by software, the engine will be locked immediately after the ignition is turned off. The alarm mode continues until the Anti Hi-jack is completely turned off.

Disabling Anti-Hi-Jack: 1. To disable Anti-Hi-Jack during a 30 second pause 1, as well as during warning mode 2, without turning off the ignition, use the emergency shutdown button to enter the first digit of your PIN code by pressing it the appropriate number of times . If the code is entered correctly, after 3 seconds the signal lights will blink twice, the LED will go out, and the Anti Hi-jack will turn off. 2. If Anti H-jack is activated remotely, then during the first 30 seconds (before the start of sound signals), it can also be turned off by pressing button 3 again for 3 seconds on the same remote control that was turned on. 3. When the system is already in alarm mode 3, then to disable the Anti-Hi-Jack, regardless of the activation method, you must enter the full emergency shutdown code, having first turned off and turned on the ignition again. If an incorrect code is entered twice, the system will block further code entry for 2 minutes. The LED will blink twice

ATTENTION! If the Anti-Hi-Jack anti-theft procedure is activated, the system is blocked from executing any remote control commands. To temporarily prevent Anti-Hi-Jack from being activated, you can use Valet mode

Doesn't start with key fob

If your car does not start with the key fob, that is, the problem is related to the autostart of the car, then if you have a temperature sensor, you need to set it to a higher temperature. Then the car will be able to warm up automatically and there should be no problems with autostart. If the starline alarm also does not allow the car to autostart, then the problem may be related to the car’s wiring. It's worth finding out how the starter in your car is connected. If the starter connection occurs in a gap, then it is worth removing it and leaving one single wire.

It is possible that the car owner has reset the settings to factory settings. In this case, you shouldn’t even be surprised that your car won’t start from autostart. When such a problem occurs, the crawler stops working because your car's chip is not showing up, and that is why the car does not autostart properly. In order to solve this problem, you must definitely visit the service center where the alarm was installed. Re-setting the car alarm will take just a few minutes for the technicians and will save you from this problem.

Engine stalls after starting

If the car starts and then stops after starting the engine, the problem is most likely related to the car's immobilizer issuing the start command. In this case, there are several possibilities:

• Key alarms have a damaged transponder chip or the chip is out of range of the autostart unit processor;
• Keyless alarm systems have software errors in the bypass system that require reprogramming.

By eliminating the immobilizer malfunction, you will remove the blockage in the ignition system. However, if the starter turns the crank when the bypass is on, but the engine does not start, it is not an immobilizer. The alarm may simply not be connected to the engine control circuit and should be checked more closely and reconnected.