What is the bolt pattern on a VAZ 2114 – wheel sizes, explanation, how to install 4×100 wheels

4*100 instead of 4*98

There will also be diameter care! How will it get up? Either repress the hub onto a hub with a 4*100 drill, or buy other discs.

You know, I usually change the wheels on a car myself and a couple of times I forgot to tighten the nuts. While driving, I immediately felt a strange noise - I tightened the nuts and that’s it. After all, a bolt or nut does not immediately unscrew and therefore it is not entirely clear how to drive, what would not feel any extraneous noise when driving. If the wheels fall off while driving, then as a rule, if one or two stud bolts burst (they are simply overtightened) and the rest break without bearing the stress. In Russia there is no culture of installing wheels. A torque wrench is exotic. In In Germany, during certain maintenance, they simply stupidly change the bolts, regardless of the degree of wear. You should have seen the condition of the bolts on cars from Russia, and even pull them with a pipe wrench or a gun at maximum power.

READ How to install a juicer on a manual meat grinder

I don’t argue. In Russia we have everything in one place. I described the real moments of using these bolts on Russian cars. And about aluminum nuts in general: at one time I wanted to buy ENKEI RS 05 and RAYS aluminum nuts for them, I visited all my tire shops city, so they looked at me like I was crazy - how can the nuts be aluminum?

Source

Instructions for removing the steering wheel

Removing the steering wheel of a VAZ classic is necessary in the following situations:

• to repair the horn button or control mechanism;
• to align the cross bar after the front wheel alignment procedure;
• for the purpose of replacing the standard steering wheel with another, more successful or sporty one.

Narrow and awkward steering wheel of VAZ 210102

On the six, the steering wheel is prettier, but just as awkward

All of the listed elements can be removed equally simply, although there are small differences in the disassembly technology, which is done using this set of tools:

• 2 types of screwdrivers: flat and Phillips;
• head for a nut 20 four mm, extension spacer and knob;
• rags.

The most successful steering wheel was installed on the fourth, fifth and seventh VAZ models

Also reserve a small amount of thick lubricant such as Solidol for applying to the splined part of the shaft.

Installation instructions

First, before assembly, lubricate the shaft splines with grease, then proceed in reverse order:

• Place the control wheel
  on the splines, aligning the previously made marks. If the task is to align the position of the bar or install a new product, try to install it very evenly.
• Place the nut inside the head, slide it onto the thread using an extension and tighten.
• Hold the steering wheel and tighten the nut with a wrench.
• Connect the battery and try to drive the car 50 thousand 100 meters on a road free of traffic. This way you make sure that you have set the steering wheel position correctly. Otherwise, unscrew the nut again and move the element one tooth to the right or to the left.
• Reinstall the top trim.

Will 4x98 wheels fit 4x100?

The trailer we purchased has a standard AvtoVAZ 4x98 hub. There was a need to put larger wheels on it, 15″ to be precise. But as it turned out, stamping 4x98 R15 is a huge rarity! After searching the Internet, I realized that there are options to install Japanese wheels with 4x100 drill bits on 4x98 hubs. People who know, please tell me: are 4x100 wheels on a 4x98 hub worth it, is it realistic, what needs to be changed, what are the pitfalls?

— Bolts with eccentric. Cheap, I don't know if it's reliable. People are driving. — Order adapter plates with the required bolt pattern from a turner. — Find 4*98 disks. In theory, from Fiat and Alfa Romeo, the previous models had the same bolt pattern.

Eccentrics approx. But I heard somewhere on the Internet that they get up like this, without modification... And Fiat and Alfa are extremely rare guests in the Siberian regions))))) Finding wheels is unrealistic.

on the drome for several weeks already they have been selling wheels from alpha of two types p15 and p16 casting true =) a friend put 15th stamps from Aveo on the nine - it was great, but it’s hard to turn =)

Casting is not an option unfortunately. We need stampings for the caps

And I think the third question is reliability. This is a TRAILER, without brakes and an engine, which means no dynamic load on the wheels. So I want to find out... If this is how they put it on cars and drive them, then the trailer shouldn’t even care.

Well, some people actually drill holes in the disks and don’t bother.

About the bolt pattern of VAZ wheel rims (4x98 and 4x100)

Rating 4.5 out of 5. Votes: 46

First, let's figure out what the bolt pattern of VAZ 4x98 and 4x100 wheels means.

• 4 is the number of bolt holes.
• 98 and 100 are the diameter of the circle in mm on which they are located.

If you do the math, the distance between the bolts with a bolt pattern of 4x98 will be 69.3mm, and with a bolt pattern of 4x100 - 70.7mm. That is, the difference is 1.4mm. There are errors everywhere, including in the bolt pattern, but the difference is 1.4mm. does not allow ideal installation of wheels with a 4×100 bolt pattern on a VAZ. The simplest method is to simply tighten the disk onto regular extended bolts, or even just 3 bolts instead of 4. This method is not safe, so it is better to avoid it.

A more popular way to install 4x100 wheels on a VAZ is to use bolts with an eccentric or with an offset center. Sets of such non-standard bolts can be easily found in online stores.

The third option is to use studs, for example from the cylinder head of a VAZ 2108, which are screwed into the hubs, and the disk itself is tightened with nuts, for example, from a Niva (see also Installing studs). It is also possible to use spacers that you can make yourself. Or buy ready-made ones. It is worth considering that the width of the spacer must be at least 20mm, therefore the wheel offset will increase by the same amount. As an option, use discs with a short offset to compensate for the offset of the spacers.

If you have a lathe, you can make 4x100 holes in the disc hub. Thus, it becomes possible to install optionally 4x98 or 4x100 disks.

If discs are installed incorrectly on a VAZ with a 4×100 bolt pattern, vibrations may appear at speed, and during sharp braking, death may occur, so before installation, think about safety first!

By the way, do you know what tires and wheels are suitable for the VAZ 2110?

How did you install 4x100 wheels on the VAZ?

Photo source:

• Che-guevaro logbook from Drive2.ru

Interesting site? Share with your friends

What do you need to know about installation?

The optimal radius, corresponding to the technical characteristics of the car and allowing it not to lose speed, is supplied under the code R14. In the factory format these may be R13 wheels, but drivers are not too fond of them.

Once the purchase has been made, you can begin installation. This can be done either independently or with the help of employees of any service station.

It should be noted that this process does not carry any pitfalls, so you can try to install the disks on your own. This process is completely identical for 2114, 2115 and many other models. If the work is being done for the first time, or the driver does not have sufficient skills, it is imperative to enlist the support of a professional! The safety of not only the driver himself, but also other road users depends on what tires are used and whether the wheels are installed correctly.

During the work process, it is important to consider that the tires must perfectly match the size of the wheel!

The car owner definitely doesn’t need this! In addition, the selected tires must be of high quality in order to cover the 40,000 km declared by the manufacturer with the disc. If there is an urgent need, you can choose cheaper tires for the summer. With careful driving, it can last quite a long time and will not make the owner doubt the correctness of his choice. However, summer quickly passes, and the tires will have to be changed again.

In order not to purchase several sets at once, you can choose the all-season option.

Is it possible to install larger wheels according to the 2022 traffic regulations?

The short answer is no. There is a strict ban on parts of a size beyond those established by the car factory. This provision is regulated by paragraph 5.4 of the Traffic Rules.

Theoretically, you can install the wrong wheels and not drive the car anymore. It will be prohibited to operate the vehicle, since it is impossible to travel with larger tires.

The traffic rules only talk about tire sizes. But there is one “but”: the height of the tire depends on the radius of the part. It is impossible to combine wheels larger than the recommended size with regular tires.

The specified paragraph of the traffic rules (5.4) provides for the configuration of the car model available to the motorist. The owner of a basic Kia Rio with 15-inch tires can still put 16-inch wheels on the car. This is allowed because some car models have 16-inch radii. Exceeding this limit will already entail administrative consequences.

RE-EQUIPING A CAR ON YOUR OWN: IS IT POSSIBLE?

From the above description it is clear that the VAZ 2107 can be equipped with any engine from 14 VAZ models. This can be done without any special modifications, except that some difficulties may arise with the RPD. However, this power unit is compact and there is enough space in the engine compartment for it. Another thing is that it is quite difficult to find and there are big problems with spare parts.

Tuning enthusiasts are not limited to such simple options and prefer more complex tasks. It is considered especially chic for such car owners to replace the standard engine with a powerful engine from a foreign car. Theoretically, there is nothing technically impossible about this and it can be done subject to certain conditions. In the matter of selecting a suitable power unit, it is advisable to consult with specialists and study successful experience.

SELECTION CRITERIA When deciding to re-equip a car, a number of important points should be taken into account. The list of requirements that the engine for the VAZ 2107 must satisfy is as follows:

• Compliance with the standard power unit in terms of overall dimensions and weight characteristics.
• Possibility of docking with vehicle transmission units.
• Compatibility of the power plant with other vehicle systems.

The closest technical characteristics to the power unit of the “seven” are the products of such companies as Nissan and Fiat. Their motors can be used with minimal modifications.

You can purchase a suitable engine at a disassembly site for relatively little money. Before installing it on your VAZ 2107, it makes sense to diagnose it and, if necessary, make major repairs. Practice shows that replacement of some parts: oil seals, belts and other components is mandatory. Doing this by car is more difficult and troublesome.

Basic drive functions

The wheels of a passenger car perform a number of important tasks:

• rubber gasket around the perimeter;
• provide a rigid structure for the total weight of the vehicle;
• transmission of torque to the wheel.

Based on these functions, a car enthusiast can formulate requirements for disks, as well as their technical characteristics. Any product on wheels must be dimensionally balanced, durable and safe. Only after this can you proceed to drilling wheels on VAZ cars.

Corrosion protection

For reliable operation of the chassis, everything is important: the bolt pattern, the dimensions of all components, the alignment/camber settings, and even the protection of the arches from corrosion. It is the arches that are more susceptible to adverse factors than other parts of the body - from ordinary moisture during rain to reagents on winter roads

To ensure reliable protection of the arches, it is best to install lockers (fender liners) on the VAZ 2110. Such protection will cost much less than subsequent repairs of rusted arches

It is important to choose the correct size of the lockers and ensure their tight fit in the area of ​​the arches

We hope that by completing all the repair work yourself, you will provide your VAZ 2110 with many years of trouble-free service on the road.

Features of wheel sizes for the most popular VAZ models

Among several dozen VAZ modifications, the most popular models over the entire 50 years were only 2 of them, as can be judged by the number of copies sold. The wheel sizes for these cars had the following parameters, which varied depending on the year of manufacture, technical equipment and equipment of the car:

VAZ is the latest modification of the “classic”, produced on the plant’s conveyors for 30 years: from 1982 to 2012. During this time, it never changed its appearance, and the disc bolt pattern was the same - 4x98 with a central hole diameter of 58.6 mm.

If in 1982 the plant produced models with tire dimensions ranging from 5J to 5.5J, then at the end of production the concern increased the permissible size to 6J.

The radius of the wheels invariably varied from R13 to R15, which made it possible to alternate them by season, periodically changing the side profile of the tire, or immediately use all-season tires with a diameter of R14.

The VAZ 2107 tire size invariably consisted of only 3 main parameters - 175/70/R13, 185/60/R14 and 185/55/R15. The last of the listed parameters was actively in demand among lovers of fast driving on smooth city roads.

If we look at the concern’s earlier cars, we can see that the wheelbase of the Zhiguli has remained virtually unchanged for more than 40 years. This leads to moral backwardness of the technical equipment of the plant's products. At the same time, the lack of new developments greatly reduces both the speed of release from the assembly line and the cost of engineering equipment, which leads to a very attractive retail price for the vehicle.

VAZ 2114. Produced in a smaller range - from 2001 to 2013. The car was just a restyled modification of the classic “nine”. The legacy of the outdated model did not affect the high popularity of this Lada, and all the wheels that were installed on hubs in the basic version had the same traditional bolt pattern 4x98, DIA 58.6 mm.

European standard bolt pattern 4x100 for Lada X-Ray

Like the bolt pattern of the VAZ 2114, the width of the wheel rims was not much different from the “seven” and fluctuated between 5J – 6J for the entire production period. As for radius, the concern has completely eliminated the 15-inch diameter from the factory equipment, without prohibiting drivers from installing this parameter as an option. The bolt pattern of VAZ 2114 wheels in the current size also made it possible to install standard 4x100 wheels in accordance with the sizes usual for Europe.

Not a single Lada model has ever looked aggressive; the hallmark of the product was practicality and reliability in operation. The concern did not use extreme overhang indicators, and the wheels were always hidden under the body arches. The average ET limit values ​​for both VAZ 2107 and 2114 were ET25...35 mm, and deviations from this characteristic obligated drivers to install additional mudguards on the side parts of the body and change the design of the hubs, making them more durable to avoid deformations.

Panel From Priora V VAZ 2110

Salon from Priora in VAZ 2110

You can diversify the interior of your car in various ways, and one of them is to install an interior from Lada Priora. It is not necessary to install the entire Priora interior in a VAZ 2110. You can also focus on its individual elements (ceiling, plastic, etc.).

The old interior of the VAZ 2110 is already quite boring, I want to somehow refresh the interior. Of course, you can install various interior parts from a foreign car (for example, seats, armrest, sunroof, etc.), but this requires a lot of time and desire to tinker, tinker, and adjust. I want to change dozens of interiors without effort. just take and install new plastic, seats, tunnel, ceiling or panel..

Then you should pay attention to the interior from Priora. Almost all interior parts of the Priora fit the VAZ 2110-12 without significant modifications (except for wiring).

Let's take a closer look at each detail of the interior:

More factory ones - how's that?

There are certain recommended parameters that car owners must adhere to. All of the options offered by the manufacturer have passed special tests. This means that it is the recommended wheels that will allow the car to improve its performance with minimal negative consequences.

As an example, we can look at a specific situation. Let's assume that a car enthusiast purchased a vehicle with 15-inch wheels. Moreover, the same car model with a different configuration has parameters of 17 inches. Consequently, a motorist can safely install wheels with any of the proposed indicators on his vehicle.

However, it is important before installing wheels of a different configuration to carefully study all the recommendations in the documents for your own vehicle. The papers must contain information about which tires and wheels cannot be installed

“Do not” means that conversion to a non-recommended size will result in degraded performance.

As a conclusion, we can say that “larger than factory” wheels are any model whose size exceeds all recommended ones. However, even changing parameters as part of the advice of suppliers leads to changes in the characteristics of the car.

It must be remembered that the wheel is not a complete part. It consists of tires and wheels that are not used separately. Therefore, it is difficult to talk about increasing the size of the wheel unambiguously. Sometimes enlarging the disks does not lead to a change in the diameter of the entire wheel.

How to determine bolt pattern

Each make and model of car has individual bolt pattern parameters. There are special tables for this, based on which you can select disks.

If it is not possible to use tables, or if your car is not included in them, you can determine the bolt pattern yourself. To do this, we count the number of holes for mounting the disk. The first parameter is there. Determining the diameter of the circle on which the holes are located is a little more difficult.

For disks with 3 holes, measure the distance between the walls of adjacent holes and multiply it by 1.155. The result obtained will be the desired diameter.

Theory

So number 4 is the number of bolt holes. And the second number is the diameter in mm of the circle in which they are located. It is easy to calculate that the distance at which the bolt is from the bolt, with a spread of 98, will be 69.3 mm.

This value is the same for all wheels installed on the VAZ 2110. But in foreign cars, most of which have a bolt pattern of 100, one bolt is located at a distance of 70.7 mm from the other.

The difference is 1.4 mm, and this will no longer allow ideal installation of wheels with a 4x100 bolt pattern on a VAZ 2110.

Difference between bolt pattern 4*98 and 4*100

Preparing for adjustment

Most often, the VAZ 2110 camber and alignment are installed at a service station, but you can do it yourself. First of all, check whether there is play in the bearings and whether the steering is loose. At the same time, check the diameter and absence of deformation of the disks, air pressure in the tires, and tread wear.

VAZ 2110 front suspension assembly diagram

Naturally, if a wheel is loose, action will need to be taken, and one with improper tread wear may need to be replaced. Wheels standing on the ground need to be pulled relative to the vertical. If you find any play, have a helper apply the brake and check the play again.

If it disappears, the bearing needs to be replaced. If after this the size of the play not only does not disappear, but only decreases slightly, the suspension needs to be checked, repaired, and sometimes replaced.

Front wheel hub diagram

After this, hang the wheel and check the play again. It is possible that the play has disappeared, but the wheel turns jerkily or is simply difficult, then you need to slightly expand the diameter of the bearing installation site.

If you hear a grinding noise, the bearing needs to be replaced.

Self-adjustment

Next, you need to stand on a flat surface and load the machine, as recommended by the manufacturer. That is, about 320 kg in the cabin, and 40 kg in the trunk.

The first adjustment is to set the tilt angles of the steering axis. The second is collapse, the third is convergence.

In this case, the camber angle in the loaded state should be 0 ° 30 '+ - 30'. The toe should be within 0°15'+ -10' and the angles of attack should be 0°20'+ -30'.

Remember that camber and other wheel adjustments are necessary in all cases when you in any way interfere with the operation of the front suspension of the VAZ 2110.

Wheel alignment

After replacing wheel rims, the dimensions and bolt patterns of which differ from those provided for by the design of the VAZ 2110, it is necessary to make all the necessary adjustments in order to ensure reliable protection of the entire chassis, as well as tires and arches.

Correct alignment angles are required for each front wheel. There are three parameters that require correct installation: wheel toe, caster angles of the steering axles, and camber angles of each wheel.

Wheel installation options

The rules by which the parameters of the front wheel are set are as follows:

1. You won't go far if everything hangs out the way it wants, and the car is pulled to the side when it should be going straight. To ensure the stability of each front wheel, they are installed strictly at the required angles to the body and suspension elements. This is called the longitudinal inclination angles of the turning axis. Installation dimensions are indicated in the instruction manual;
2. Camber is the angle between the plane in which the wheel rotates and the vertical. The camber bolt helps install it (it secures the telescopic strut and steering knuckle). If the camber is installed incorrectly, the car “steals” and the tire tread wears out more on one side;

Wheel installation options

Will 4x100 wheels fit on a VAZ?

Messages: 3966 Registered: 06 Feb 2006, 00:00 From: Tyumen Experience: since June 1997 Awards: 1

Thanked: 1 time Thanked: 4 times

Post by sodium » 24 Oct 2009, 21:50

Psion, don't get angry. Just because you left for 2 years doesn’t mean that someone else will leave too. This is not an axiom, this is your and only your practice. So it's lucky that nothing happened. Or maybe something has already happened, but you don’t know about it yet.

Nobody says that there will definitely be a jamb. We are talking about the fact that when installing non-standard disks, there is a possibility of an unfavorable outcome. And it's big.

I personally do not recommend installing them, just because it SHOULD NOT be this way.

Messages: 24 Registered: Mar 30, 2009, 00:00 Awards: 1

Post by Black72 » Oct 24, 2009 10:23 pm

Messages: 1103 Registered: October 20, 2006, 00:00 From: 86 region - 72 region - 23 region (Sochi) Awards: 1

Thanked: 1 time Thanked: 1 time

Post by Alex25 » 25 Oct 2009, 08:13

Messages: 1237 Registered: Nov 28, 2008, 00:00 Experience: 2005 Car: Maxima 3.0 Awards: 1

Thanked: 6 times Thanked: 19 times

Message TAXI » 25 Oct 2009, 09:23

Messages: 263 Registered: Dec 23, 2007, 00:00 Car: bmw116 Awards: 1

Post by ilyason » Oct 25, 2009, 10:07 am

Messages: 2064 Registered: October 25, 2009, 00:00 From: Tyumen Experience: 07.1994 Car: Nexia Awards: 1

Thanked: 75 times Thanked: 91 times

Post by Scorpio » Oct 25, 2009, 01:10 pm

Messages: 1103 Registered: October 20, 2006, 00:00 From: 86 region - 72 region - 23 region (Sochi) Awards: 1

How to make the necessary calculations

Acceptable tire sizes for 14-inch wheels: 175/65 R14 and 185/60 R14. Moreover, the second option is preferable.

However, the diameter of the wheel can be calculated very simply if you know how the characteristics of the rubber are deciphered. Let's do this for the VAZ 2109.

Let's take a standard 175/70 R13 wheel. 175 – tire width in millimeters; 70 – height of the rubber profile as a percentage of the width, that is, in our case 175 x 0.70 = 122.5 mm

Disc diameter 13 inches = 13 x 25.4 = 330 mm.

The total wheel diameter is the sum of the rim diameter and two profile heights. Total 330 + 122.5 x 2 = 575 mm.

Having made calculations in a similar way, we get the following figures for comparison:

• 175/70 R13 – 575 mm;
• 175/65 R14 – 583 mm;
• 185/60 R14 – 577 mm.

We see that the last option is the most suitable. It is also 10 mm wider, which will provide us with a shorter braking distance due to the increased contact patch with the road, better handling, and resistance to tire bending in corners at high speeds due to the reduced profile height. But at the same time, a wide tire is more prone to hydroplaning at high speeds than a tire with the same parameters, but narrower. Also, impacts from driving through road potholes will be more strongly transmitted to the body of a car with wheels of low profile height.

Table for selecting suitable wheels

To confirm your words, data on permissible wheel rim sizes can be found in the factory instruction manual.

Wheels with a larger radius, for example with a diameter of 15 inches, are also suitable for the Samara, but they are not recommended by the factory, so there may be problems with passing the technical inspection. For such wheels, you should choose tires with a dimension of 185/55 R15. With a stretch, 195/50 R15 will also work, but it’s better to play it safe and try it on if your friends have similar ones. In this case, the wheel may “rub” due to the tire being too wide.

Acceptable sizes of tires and wheels for the VAZ 2109 Lada Samara

Useful video

You can glean additional interesting information from the video below:

In all modifications of the VAZ 2110, the bolt pattern in the factory configuration is 4x98. “Dozens” rolled off the assembly lines with stamped wheel disks - diameter R13, as well as with cast ones - diameter R14.

The wheels were fitted with tires measuring 175/70 R13 or 175/65 R14. However, if the sizes of wheels and tires are relatively clear values, then what a bolt pattern is is a big mystery to many.

Wheel parameters and bolt pattern for VAZ 2110, 2111, 2112

Types of rims

Having figured out what the bolt pattern of VAZ 2114 discs is and how to compensate for it when using discs with a different type of drilling, let’s now talk about the discs themselves.

Currently, you can find 3 main varieties of them on sale, namely:

• steel wheels;
• alloy wheels;
• forged wheels.

Steel wheels come as a standard factory option on all VAZ cars. They are characterized by low cost and, at the same time, good reliability and durability. In addition, in the event of an accident they are deformed without destruction, which in most cases allows them to be straightened and used again.

Cast wheels are made from aluminum alloys and due to this, as well as the overall complexity of their production, cost significantly more. At the same time, they are distinguished by a variety of shapes and options, due to which they are in high demand among those who like to tune their car (another important advantage is their low weight compared to stamped steel wheels).

How discs are marked

Each disc has an individual marking indicating:

•number of holes for mounting to the hub;

•diameter of a conventional circle passing through the axes of these holes;

Wheel rim bolt pattern compatibility table

Let's look at an example of full marking 9JX16 Н2 5/112 ET 35 D 66.6

9 – disk width (in inches);

J – designation indicating that the disk is intended for a one-wheel drive car (wheels for all-wheel drive vehicles are designated by two letters JJ);

X – disc manufacturing method (cast);

16 – installation diameter (in inches);

H2 – marking indicating the number of annular protrusions holding the tubeless tire (2);

Inner side of the disc

People like to tune these two parameters (diameter and width). Most often, they strive by all means to increase the seat diameter and width of the disk. At the same time, the tire, in order to fit in the wheel arch, becomes low-profile, which warms the soul of many. But at the same time, we should not forget about GOST for the depth of potholes on our roads - there is such a document! A hole up to 5 cm deep and with a sharp edge has a right to exist. And no one will be punished if you damage your car in it. Now imagine what will happen to low-profile tires in such a pit, even a “GOST” one. For example, with standard rims on Hyundai cars with a diameter of 15 and 16 inches, owners manage to install... 18-inch ones on Solaris! For example, with a tire measuring 215/35 R18, this solution provides only 75 mm of clearance between the tire seating surface and the road. Such a tire will most likely suffer (the bead may be punctured) even in a “permitted” hole.

However, there is an alternative approach. The bottom line is to try to install wheels of the minimum size, just so that they do not cling to the brake mechanisms, and “catch up” with the diameter with a high-profile tire. Among the advantages of this method, we should note the softness of the ride and the lower price of small-diameter tires. For example, the design of the Hyundai Solaris chassis (and the Kia Rio platform) allows the use of 14-inch wheels. And with a tire measuring 195/70 R14, you get quite normal wheels - a little higher (less than 3%) than the original ones, measuring 185/65 R15. But the softness of the ride becomes like that of a Renault Logan.

14-inch wheels Kia Rio

It should be noted that the same options for using discs of different diameters are also implemented on crossovers. For example, on the previous generation Nissan X-Trail you can install 16-inch wheels, which is clearly evidenced by the re-rolling of this diameter. And the car came off the assembly line with 17- and then 18-inch wheels. Although there are known cases of using wheels up to 20 inches. Here, too, the only question is what do you want to get: a car that gravitates towards an SUV or a tough “sports barn”. The main thing is to know moderation in everything, because the engine and gearbox are not changed.

What has VAZ changed?

Now let's talk about how VAZ betrayed its size. Even on the progenitor of the first Zhiguli, the FIAT-124, the diameter of the circle on which the holes for the bolts were located was 98 mm. And since then, this size has been strictly observed on all VAZ cars, except Niva and Oka.

By the way, Italians are also faithful to traditions. For example, on the FIAT Albea, which was officially sold in Russia, it was possible to attach a wheel from a VAZ.

Priora wiring in VAZ 2110

The biggest problem is that the wiring on the Priora is multiplex, it is not at all similar to the wiring on the VAZ 2110, and the same on the Euro. Only the plugs are different!

Because All connectors on the Priora differ from the connectors on the VAZ 2110. Then you can:

Change the wiring of the VAZ 2110 to wiring from the Priora. Leave the VAZ 2110 wiring and change only the pads from the Priora. In the first case, you will need all the Priora wiring (under the hood, inside the cabin).

In this case, the most difficult moment is to merge the rear old part of the wiring with the wiring from the Priora.

Thus, the process is complicated by replacing all the wiring, but is made easier by the fact that all the pads do not need to be soldered.

In any case, you will have to study literature from Priora and VAZ 2110 for a long time.

The only connector that will fit is the connector connecting the interior wiring and the injection wiring (only for VAZ 2110 with 1.6 internal combustion engine)

The mounting block will also have to be replaced with the Priorovsky one, because it doesn't look like a decimal at all.

Because In the Priora, air flow control is automatic, then if necessary, you need to install an electric drive in the heater.

The Priors now have an electrical package control unit (2170-3763040). It is responsible for all electrics (ESP, central locking, interior light, built-in alarm, turn relay, etc.) and combines the functions of an anti-theft system, immobilizer and hazard warning lights.

Installing it in the top ten will require additional investment and time, so it is usually not installed in the VAZ 2110.

The price of the electrical package control unit is about 3000 rubles.

Some of the Priora's wiring comes with the panel, and some must be purchased separately.

The price of wiring the Priora separately is about 1500 rubles.

What options are there?

In order to choose the right wheels for a VAZ 2115, you will need a certain amount of attention and skill

It is important that all components fit perfectly together. Then the likelihood that the selected model will last a long time automatically increases

Conventionally, all types of disks can be divided into several categories:

The first of them are included in the basic package and have excellent technical characteristics. Steel wheels are inexpensive, but nevertheless reliable and durable. They can be chosen by a driver who values ​​comfort and ride quality, but does not accept any excesses.

In turn, alloy wheels on the VAZ 2114 are made of light alloy materials that contain aluminum. Externally, they noticeably outperform factory equivalents, without losing in technical terms. The only disadvantage of alloy wheels is their price, which differs from steel wheels by more than two times. However, a good quality characteristic will more than justify the financial costs.

Forged wheels are classified as exclusive with excellent technical characteristics. For forging, aluminum alloys are used, which are first exposed to a press. After the configuration of the part is formed, high-precision metal-cutting machines bring it to the required shape.

The hardness of such discs is approximately 2.5 times higher than normal! That is why it is more advisable to install them on a racing car, and not on those that move around the city. Forged wheels look very stylish, but is their high price justified in ordinary use?

Of course, the right to choose the tire size, their appearance, etc. is entirely provided to the driver. In this matter, it would be useful to listen to a specialist who will select the best option based on the conditions in which the car will be operated.

What kind of drilling on a VAZ-2114: photo and video

Beauty, of course, requires sacrifice, but it’s still not worth going beyond the boundaries of healthy logic. When choosing wheels for a VAZ-2114, you need to be guided not only and not so much by the design of casting or stamping, but also by the dimensions in the first place. Compliance of the factory seating dimensions with the dimensions of the new wheels will guarantee safe operation of the vehicle.

What kind of drilling is on the VAZ-2114

One of the main parameters that you should pay attention to when replacing standard wheels on a VAZ-2114 car is the dimensions, location and diameters of the mounting holes, PCD, pitch circle diameter, or in simple terms, drilling or bolt pattern

Bolt pattern on a VAZ-2114 wheel

Bolt pattern - this characteristic is expressed in two numbers and indicates the distance between the centers of the mounting holes and their number.

Drilling for all VAZ cars (except Oka and Niva) - 4x98, four holes, the centers of which are located at a distance of 98 mm from each other.

However, this is a simplified designation for the user. The disc manufacturer is required to take into account both the diameter of the holes, their number, the distance between their centers, and the diameter along which the centers of the holes are located. Such a designation would complicate the selection of disks by the user, so knowing drilling in the “number of holes/distance between them” format is considered sufficient.

A few more wheel parameters

The drill bit can be measured using the spare wheel. In all SAMARA drilling 4*98

There are several more parameters that relate to the original VAZ-2114 rims - the width of the stock rim is 5.0J, the offset of the ET45 rim, the diameter of the centering hole at the hub is 58.5.

How to install a 4x100 disk on a VAZ-2114

Most older foreign cars have a 4x100 drill. This makes it possible to diversify the choice of disks almost indefinitely. However, we must take into account that simply installing, without modifications, 4x100 wheels on a 4x98 seat will not lead to anything good. The fact is that the tolerance in the manufacture of the disk does not exceed 0.7-1 mm. That is, it is theoretically possible to put on a disk with a 4x100 fit, but this will lead to the fact that only one bolt out of four will fit exactly on the cone. The remaining fasteners simply will not tighten all the way and, as a result, the disk will sit with a distortion that is almost impossible to check by eye.

Disc with bolt pattern 4*100

The disc will not fit with its mating plane to the hub, and this will lead to the fact that it will have a runout.

Systematic runout can not only lead to the fact that the only bolt that is tightened correctly will quickly become loose, but also to instant wear of the wheel bearing, and the remaining bolts will loosen on their own. There is a way out of this situation.

Disc runout leads to rapid wear of the wheel bearing

To install a disc with a 4*100 bolt pattern, you need to either install a spacer or install studs with nuts instead of bolts.

A less reliable option is to install bolts with an offset head. A not entirely correct option is to install studs, for example, from the cylinder head and nuts from Niva, but the studs are not designed for torsional force, so the most reliable option would be to install spacers. You can carve them yourself or buy them ready-made.

But here you need to take into account several nuances:

1. The width of the spacer must be at least 20 mm, since only in this case we will ensure proper thread strength.
2. In this case, the offset of the disk will increase by the same 20 mm, which must be taken into account when selecting a disk.
3. In this case, the disc must be selected with a minimum offset in order to remove the load from the hub and somehow compensate for the difference in offset.

Using offset eccentric bolts class=”aligncenter” width=”500″ height=”375″|fcw3qayjh5a| src=»https://max-vps.ru/wp-content/uploads/d/1/0/d101bbd9ce45f3d879a2a2df8886d810.jpeg» class=»aligncenter» width=»500″ height=»375″[/img]Install wheels spacers Installing studs with eccentric nut

Video about installing spacers to change drilling on a VAZ-2114

Conclusion

Be careful when replacing disks with non-standard ones and remember that the most killer appearance can never replace safety, especially at high speeds. Have a successful and safe journey everyone!

In all modifications of the VAZ 2110, the bolt pattern in the factory configuration is 4x98. “Dozens” rolled off the assembly lines with stamped wheel disks - diameter R13, as well as with cast ones - diameter R14.

The wheels were fitted with tires measuring 175/70 R13 or 175/65 R14. However, if the sizes of wheels and tires are relatively clear values, then what a bolt pattern is is a big mystery to many.

Wheel parameters and bolt pattern for VAZ 2110, 2111, 2112

Disk parameters 2114

Bolt pattern (also known as disk drilling, also known as pitch circle diameter) is a value that shows the number of mounting holes in the disk, as well as the linear distance between them. It is indicated, respectively, by two numbers. The standard wheel bolt pattern for the VAZ 2114 is 4*98. This means that the disk has 4 mounting holes for bolts, and the distance between the centers of these holes is 98 mm.

It is worth noting that such drilling is standard not only for the 14th model, but also for all other cars produced by AvtoVAZ, with the exception of the Oka and Niva.

In addition to the bolt pattern, there are a number of other important parameters of the disk that can be useful when choosing non-original spare parts. These include: the width, which is designated as 5.0J, the offset of the disc, marked as ET45, and the diameter of the hub centering hole, equal to 58.5 mm. The mounting bolts have an M12 thread with a pitch of 1.25 mm.

conclusions

On the VAZ-2114, many motorists practice installing alternative engine options to increase power and other quality indicators. This modification, as practice shows, requires more time, effort and finance, and is therefore considered not economically feasible. Thus, experts and experienced motorists recommend tuning the standard engine.

Tuning is not just about changing the appearance of a car, as many people think. In fact, revisions often concern the technical component. Someone makes changes to the exhaust system, changes elements of the factory engine.

But there is a more drastic, expensive and interesting option - change the engine. With the new engine you get different technical characteristics, increased power, increased maximum speed, better acceleration.

And what's under your hood? Replacing an engine is a fairly serious step that requires you to think through every stage, from choosing a new engine to the consequences that such work can result in.

VAZ 2114 wheel bolt pattern

The production of the fourteenth VAZ model began in 2001. Since that moment, the designers have not made any changes to the wheelbase design or bolt pattern parameters.

The standard parameters of factory stampings are as follows: 4X98 LZ*PCD, where LZ means the number of mounting holes, and PCD is the diameter of the circle in millimeters on which the mounting holes are located.

Deviation from the norms without additional spacers is impossible, so most cars of this model are driven in a 4X98 configuration. If desired, the standard landing mount can be modified using spacers. Also, the changed wheel bolt pattern on the VAZ 2114 allows the installation of larger wheels. For owners, this opportunity allows them to improve the appearance of the car, because... With factory sizes, even Titans look modest. Drilling is a value indicating the distance between the mounting holes, so deviation from the factory standards will not allow the use of “Titans” from another car. Note that 4X98 drilling is used on most VAZ models, so stampings can also be installed on the “four” from classics, “Priors”, “Samara” of the first generation, etc.