The diameter of the central hole, another marking is CO.
Disclaimer: Although the data represents official manufacturer figures, the information above is for reference only and is not guaranteed to be absolutely accurate.
- Ford Mondeo IV car dimensions
- Ford Mondeo IV wheel sizes
- Ford Mondeo IV tire sizes
- Ford Mondeo IV body dimensions
- Ford Mondeo IV wiper sizes
- Ford Mondeo IV battery sizes
- Ford Mondeo IV Wheel Bolt Dimensions
- Ford Mondeo IV air filter sizes
- Dimensions of cabin filters Ford Mondeo IV
- Ford Mondeo IV fuel filter sizes
- Ford Mondeo IV engine sizes
- Ford Mondeo IV oil filter sizes
- Ford Mondeo IV trunk dimensions
- Ford Mondeo IV piston sizes
- Ford Mondeo IV cylinder sizes
- Ford Mondeo IV fuel tank dimensions
- Ford Mondeo IV seat sizes
- Ford Mondeo IV valve sizes
- Ford Mondeo IV piston ring sizes
Comments. Have questions? We will answer everything.
Standard wheel sizes for Ford Mondeo 2.0i MK4
The Ford Mondeo 2.0i MK4 model was produced from 2007 to 2010. Table of standard and suitable wheel sizes for Ford Mondeo 2.0i MK4.
Disc drilling parameters are usually called bolt pattern:
- LZ (number of holes)
- PCD (hole center circle diameter)
- ET (disc offset)
- DIA (hole diameter)
Useful articles and reviews Announcements of certificate drawings among subscribers. Subscribe to VK group
Despite the fact that this information is taken from the websites of auto manufacturers, our catalog is for informational purposes only and does not guarantee full compliance of the proposed sizes with your car.
Disc overhang size
Offset is one of the most important criteria for selecting wheels. It determines the distance between the vertical axis of symmetry of the disk and the plane of contact between the disk and the hub.
Disk offset occurs:
•positive (the vertical axis of the disk is located behind the mating plane);
•zero (the disk axis is superimposed on the mating plane);
•negative (the disk axis is located in front of the mating plane).
The disc offset parameters are strictly regulated by the vehicle manufacturer and are directly related to the suspension kinematics. A change in the standard overhang value is allowed by no more than 5 mm.
Below are tables indicating the bolt pattern, offset and diameter of the central hole of the disks for popular car models.
Wheels for Ford Mondeo 4, size 16
Depending on the vehicle’s configuration and the market for which it was intended, the rims differ in both appearance and size. The main list of Ford configurations allowed you to choose between wheels of 16, 17, 18 inches. Wheels on Ford Mondeo 4 measuring 16 inches are standard and the most common.
"Ford Mondeo 4"
The standard seat width varies for wheels of different diameters. For 16 inches it was 6.5 inches, for 17 - 7.5 inches, and for 18 - 8 inches.
There is an option with factory-installed 16-inch steel wheels with a width of 6 ½ inches.
Steel wheels for Ford Mondeo 4 are popular due to their high maintainability, which is important for residents of peripheral settlements and areas where the condition of the roads is less fortunate. When struck, such a rim does not burst, but bends. In case of minor damage, they can be easily restored by straightening them with a hammer through an impact spacer.
Steel disc
Original wheels for Mondeo
In order not to spoil the exterior of such a beautiful car as the Ford Mondeo, it needs to be equipped with alloy wheels with a decent design.
The vast majority of cars leave the factory with stampings, and even if the wheels of the first configuration are alloy, you still have to buy another set for winter tires. This is why car owners ultimately have to choose which wheels to install on a Ford Mondeo so that it is both beautiful and functional.
Let's see what interesting things can be found in stores using the example of the main base size 6.5*16 5*108:
SCAD Drive
This model is offered by the Krasnoyarsk SKAD plant in several paint options: selenium, white and three polished options.
KiK Mondeo
Option from another Krasnoyarsk manufacturer, with seven pairs of expanding spokes. Silver color.
KiK Iguana KS-570
A very interesting model in design, offered in two paint options - dark platinum and wenge. The latter is shown in the photo.
Yamato Sakuradjima
Multi-spoke model from the Japanese manufacturer Yamato. The color is matte black, with polishing on the front surface.
Cross Street Y4601
Chinese manufacturers delight with the greatest variety. For example, the Cross Street model that you see in the photo is presented in at least 10 exterior design options. Here you can find different types of polishing, black and white with a red edging on the rim, silver, graphite - there is plenty to choose from.
YST X-7
And these are the wheels of another Chinese brand – YST. An incredibly interesting and unconventional design, available in several color options, will decorate any car.
Original FORD FD18
Under the Italian brand, but made in China, a great variety of original models are offered, including Mondeo. Agree that the graphite powder coated FD18 shown here looks absolutely stunning.
This is a small fraction of the assortment that can be seen in stores today. We just drew your attention to the most interesting models in our opinion. Now let's see what tire to put on them.
Selection of alloy wheels for Ford Mondeo 4, size 17
In addition to the original wheels on the Mondeo IV, you can choose products from third-party manufacturers that have a more original design, which will have a positive effect on the individuality of the car.
Main characteristics indicated by manufacturers:
- Bolt pattern PCD (sometimes BCD) Pitch(Bolt) Circle Diameter (for example, for Mondeo - 5x108);
- ET—departure;
- DIA - diameter of the central hub hole (for Mondeo - 63.3 mm);
- Disc seat width.
This information is not always indicated physically on the product. Stamped steel rims are marked on the front; on light alloy wheels it should be found on the inner surface. Most often, the markings can be found in the area of the spokes, sometimes in the hub plane; in rare cases, the markings are applied to the inner surface of the disk flange, and after mounting the tire it remains inaccessible to view.
First of all, when selecting car wheels for the Ford Mondeo 4, you need to correctly select the bolt pattern and the mounting diameter of the central hole.
The diameter of the central hub hole must be no less than 63.3 mm.
Also, catalogs often indicate such parameters as disc offset (ET) and its width in inches. These indicators may differ from those recommended by the manufacturer, but within reason. The offset is the distance between the plane of the axis of symmetry of the wheel and its mounting plane. Discs come with a positive offset, when the hub plane is bulged relative to the axis of symmetry, negative offset - the hub is deeply recessed and zero offset. It is difficult to distinguish negative from zero overhang by eye, since the mounting plane in both cases is deep relative to the front plane.
In the case of a large overhang, everything is much simpler - the disc may simply not stand up, the elements of the brake system will serve as a barrier to this, often the rim rests on the caliper.
Original wheels on Mondeo are made with an offset of 50-55 mm.
Cast drive
You shouldn’t play too much with wheel width either. The tire's profile changes as this indicator increases or decreases, which forces it to operate in contact patch conditions that engineers may not have thought about during design, and this will affect the ride characteristics and handling of the vehicle. Also, discs that are too wide can rest against the shock absorber strut or other chassis elements, preventing installation and operation.
Wheels for Ford Mondeo 4: alloy wheels for FORD Mondeo IV, sizes and parameters
In order to find out the bolt pattern of Ford wheel rims, you need to find a combination in the designation similar to the following: 5 x 108.
- Standard wheel sizes for Ford Mondeo 2.0i MK4
- Disc drilling parameters are usually called bolt pattern:
- Ford Mondeo MK4 2008 1.6Ti
- Reference data
- Ford Mondeo IV 2014 2.5
- Wheels and tires
- Ford Mondeo IV 2014 2.3
- Wheels and tires
- Ford Mondeo IV 2014 2.2 TDCi
- Wheels and tires
- Ford Mondeo IV 2014 2.0 TDCi
- Wheels and tires
- Ford Mondeo IV 2014 2.0 SCTi
- Wheels and tires
- Ford Mondeo IV 2014 2.0 LPG
- Wheels and tires
- Ford Mondeo IV 2014 2.0 FlexiFuel
- Wheels and tires
- Ford Mondeo IV 2014 2.0 EcoBoost
- Wheels and tires
- Ford Mondeo IV 2014 2.0
- Wheels and tires
- Ford Mondeo IV 2014 1.8 TDCi
- Wheels and tires
- Ford Mondeo IV 2014 1.6 Ti
- Wheels and tires
- Ford Mondeo IV 2014 1.6 TDCi
- Wheels and tires
- Ford Mondeo IV 2014 1.6 EcoBoost
- Wheels and tires
- Wheels for Ford Mondeo 4, size 16
- Description of the characteristics of wheel rims for Ford Mondeo 4
- Reasons for replacement
- Wheel size for Ford Mondeo 5 car, original R18
- How to determine bolt pattern
- Tires and wheels for Ford Mondeo, wheel size for Ford Mondeo
- Selection of alloy wheels for Ford Mondeo 4, size 17
- Compatibility table
- Wheels for Ford Mondeo
- General background information
Reasons for replacement
We don't often come across the purchase of rims. Typically, the average driver who purchases a new car and uses it for 5 years, which is 100–150 thousand kilometers, does not have to deal with their replacement. You only have to deal with buying new ones, for example, for winter tires. But the owner of a used car may have to replace the disks that the previous owner left him. The reasons may be the following:
- the disk is severely deformed and cannot be straightened, and therefore cannot be balanced;
- the rim is slightly deformed, but when it was straightened something irreparable happened - it burst;
- the third reason is trivial - you don’t like the design of the wheels or you want a larger diameter and low-profile tires, respectively;
- The inner part of the rim to which the tire is attached began to corrode; due to corrosion, a tight fit is not possible and the wheel is slipping. This is usually treated by stripping, but there are advanced cases and the rim must be replaced.
It doesn’t matter what led to this, but before purchasing, you need to look in the instruction manual for acceptable parameters and find the markings on the wheel itself.
Standard wheel sizes for Ford Mondeo 2.0i MK4
The Ford Mondeo 2.0i MK4 model was produced from 2007 to 2010. Table of standard and suitable wheel sizes for Ford Mondeo 2.0i MK4.
Disc drilling parameters are usually called bolt pattern:
- LZ (number of holes)
- PCD (hole center circle diameter)
- ET (disc offset)
- DIA (hole diameter)
Options | Disc width | Disc diameter | Bolt pattern LZ*PCD | Departure ET | Diameter DIA | type of instalation | ||
Ford Mondeo 2.0i MK4 | 2010 | 6.5Jx16 5/108 ET50 d63.4 | 6.5 | 16 | 5X108 | 50 | 63.4 | Factory |
Ford Mondeo 2.0i MK4 | 7.5Jx17 5/108 ET55 d63.4 | 7.5 | 17 | 5X108 | 55 | 63.4 | Acceptable | |
Ford Mondeo 2.0i MK4 | 8Jx18 5/108 ET55 d63.4 | 8 | 18 | 5X108 | 55 | 63.4 | Acceptable | |
Ford Mondeo 2.0i MK4 | 2009 | 6.5Jx16 5/108 ET50 d63.4 | 6.5 | 16 | 5X108 | 50 | 63.4 | Factory |
Ford Mondeo 2.0i MK4 | 7.5Jx17 5/108 ET55 d63.4 | 7.5 | 17 | 5X108 | 55 | 63.4 | Acceptable | |
Ford Mondeo 2.0i MK4 | 8Jx18 5/108 ET55 d63.4 | 8 | 18 | 5X108 | 55 | 63.4 | Acceptable | |
Ford Mondeo 2.0i MK4 | 2008 | 6.5Jx16 5/108 ET50 d63.4 | 6.5 | 16 | 5X108 | 50 | 63.4 | Factory |
Ford Mondeo 2.0i MK4 | 7.5Jx17 5/108 ET55 d63.4 | 7.5 | 17 | 5X108 | 55 | 63.4 | Acceptable | |
Ford Mondeo 2.0i MK4 | 8Jx18 5/108 ET55 d63.4 | 8 | 18 | 5X108 | 55 | 63.4 | Acceptable | |
Ford Mondeo 2.0i MK4 | 2007 | 6.5Jx16 5/108 ET50 d63.4 | 6.5 | 16 | 5X108 | 50 | 63.4 | Factory |
Ford Mondeo 2.0i MK4 | 7.5Jx17 5/108 ET55 d63.4 | 7.5 | 17 | 5X108 | 55 | 63.4 | Acceptable | |
Ford Mondeo 2.0i MK4 | 8Jx18 5/108 ET55 d63.4 | 8 | 18 | 5X108 | 55 | 63.4 | Acceptable |
You have seen scammers, the company does not provide the stated services or has already closed, we will check!
Ford Mondeo MK4 2008 1.6Ti
Generation: MK4 Engine: I4, Gasoline Power: 125 hp (92 kW)
Wheel bolt pattern parameters
PCD (number of holes x circle diameter) | 5×108 mm |
Center Hole Diameter (DIA) | 63.4 mm |
Fasteners | M12 x 1.5 |
Type of fastener | screw |
Tires | Discs | PCD | Dia | Pressure |
205/55 R16 91V Factory kit | 6.5Jx16ET50 | 5×108 | 63.4 | 2.2 |
215/55 R16 93V Tuning | 6.5Jx16ET50 | 5×108 | 63.4 | 2.2 |
215/55 R16 93H Tuning | 6.5Jx16ET50 | 5×108 | 63.4 | 2.2 |
235/45 R17 97W Tuning | 7.5Jx17ET55 | 5×108 | 63.4 | 2.2 |
235/40 R18 95W Tuning | 8Jx18 ET55 | 5×108 | 63.4 | 2.2 |
What wheel sizes does the manufacturer recommend to install?
The Ford Mondeo MK4 2008 1.6Ti is equipped with 6.5Jx16 ET50 rims and 205/55 R16 91V tires as standard. Where:
- 6.5J - rim width in inches;
- 16″ — tire diameter in inches;
- ET50 - disc offset in millimeters.
The vehicle tire marking 205/55 R16 is deciphered as follows:
- 205 — profile width (cross section of the tire) in millimeters;
- 55 — profile height as a percentage of its width;
- R - radial cord winding;
- 16 is the tire diameter in inches.
In addition, information about its load capacity and speed parameters can be printed on the rubber - load index and speed index. The load index is a two- or three-digit number; the speed index is indicated in Latin letters, for example 91V:
- 91 - maximum permissible tire load 615 kg;
- V - maximum permissible vehicle speed is 240 km/h.
Using the recommended tire sizes will help you avoid problems with handling, safety and other difficulties. What non-standard sizes can be supplied? Refer to the table; it indicates possible acceptable alternative sizes for tuning. Although there are other options that we have not described in the table. For example, wider discs of the same diameter. Or install wheels of the same width, but with a larger diameter, which is quite popular among car owners. The choice of discs is huge; you can find copies with the same parameters, but with an overhang 1-2 millimeters more or less. It is not possible to list all the options.
At the same time, the bolt pattern for all types of wheels is the same - 5x108. Thus, all disks are fastened with five bolts and the distance between them is exactly one hundred and eight millimeters. The car's hub diameter is 63.4 mm.
Ford Ford bolt pattern
Car make and model | PCD | ET | DIA |
Ford Bronco | 5 x 139.7 | 35. 38 | 86.9 |
Ford Cortina | 4 x 108 | . | 63.3 |
Ford Cougar | 4 x 108 | 35. 38 | 63.3 |
Ford Econovan | 4 x 114.3 | 35. 38 | 59 |
Ford Escort | 4 x 108 | 35. 38 | 63.3 |
Ford Explorer | 6 x 139.7 | 0. -3 | 100 |
Ford Fiesta | 4 x 108 | 35. 38 | 63.3 |
Ford Focus | 4 x 108 | 35. 38 | 63.3 |
Ford Focus 3 | 5 x 108 | . | |
Ford Galaxy | 5 x 112 | 42. 45 | 57.0 |
Ford Granada | 4 x 108 | 35. 38 | 63.3 |
Ford Ka | 4 x 108 | 35. 38 | 63.3 |
Ford Maverick | 6 x 139.7 | 0. -3 | 100 |
Ford Mondeo (iki 2001 m.) | 4 x 108 | 35. 38 | 63.3 |
Ford Mondeo (nuo 2001 m.) | 5 x 108 | 35. 42 | 63.3 |
Ford Mustang | 4 x 108 | 35. 38 | 63.3 |
Ford Orion | 4 x 108 | 35. 38 | 63.3 |
Ford Probe (iki 1992 m.) | 5 x 114.3 | 35. 38 | 59.5 |
Ford Probe (nuo 1992 m.) | 5 x 114.3 | 35. 38 | 67 |
Ford Puma | 4 x 108 | 35. 38 | 63.3 |
Ford Sierra | 4 x 108 | 35. 38 | 63.3 |
Ford Scorpio (iki 1995 m.) | 5 x 112 | 35. 38 | 63.3 |
Ford Scorpio (nuo 1995 m.) | 4 x 108 | 35. 38 | 63.3 |
Ford Taunus | 4 x 108 | . | 63.3 |
Ford Transit (iki 1992 m.) | 5 x 160 | . | 72 |
Ford Transit (nuo 1992 m.) | 6 x 180 | . | 138.8 |
Ford Transit FT 75 | 5 x 160 | . | 115 |
Ford Transit FT 100 | 5 x 160 | . | 115 |
Ford Transit FT 100 L | 6 x 169.9 | . | 130 |
Ford Transit FT 130–190 (iki 1985 m.) | 6 x 169.9 | . | 130 |
Ford Transit FT 80–190 (nuo 1985 m.) | 5 x 160 | . | 65 |
Ford Windstar | 5 x 112 | 35. 38 | 63.3 |
If you haven't found a bolt pattern for your car, write its make and model in the comments and it will be added as soon as possible. If you find any inaccuracies, please notify us about them again. Remember, by correcting the information you are helping other people looking for it.
PCD – mounting hole diameter
ET – disc offset in millimeters
DIA – diameter of the central hole for the wheel hub in millimeters
B – Wheel width in inches
D – Disc diameter in inches
Humps are protrusions on the surface of the rim made for a tubeless tire.
An example of decoding a disk label:
5.5Jx16H2 ET30 PCD: 5/112 d 66.6
Wheel width in inches (B)=5.5
Disc diameter in inches (D)=16
Diameter of mounting holes (DIA)=112
How discs are marked
Each disc has an individual marking indicating:
•disc diameter;
•its width;
•number of holes for mounting to the hub;
•diameter of a conventional circle passing through the axes of these holes;
•disc ejection.
Wheel rim bolt pattern compatibility table
Let's look at an example of full marking 9JX16 Н2 5/112 ET 35 D 66.6
9 – disk width (in inches);
J – designation indicating that the disk is intended for a one-wheel drive car (wheels for all-wheel drive vehicles are designated by two letters JJ);
X – disc manufacturing method (cast);
16 – installation diameter (in inches);
H2 – marking indicating the number of annular protrusions holding the tubeless tire (2);
5/112 – number of mounting holes/diameter of the circle on which they are located (bolt pattern);
ET 35 – disc offset value (in millimeters);
D 66.6 – diameter of the central (hub) hole of the disk.