Today, every car, regardless of type, is equipped with special protection for all electrical systems. This protection is called a fuse. They are installed so that in the event of a short circuit or malfunction, the system can turn off via a fuse, thereby protecting itself from breakdown. Fuses are used for every electrical circuit, from a small light bulb to an engine's ignition system. More important engine systems are equipped with special relays, they protect various pumps, electric motors and other powerful sources of electricity consumption.
The fuse is a small structure consisting of a plastic casing with a fusible element inside. If a short circuit occurs, the thin contact melts under the influence of current, which interrupts the electric current. The simplest electrical fuse is a thin copper wire inserted into a circuit. If the upper limit of the supplied current increases, the contact begins to melt and interrupts the flow of electricity. Here there is a description of all fuses and relays for VAZ 2113, 2114, 2115 models of injection and carburetor types, old and new models.
Interpretation of fuses and relays of injection models
The main electrical fuse module 2114-3722010-60 is located under the front engine compartment. This arrangement allows for quick access to all electrical systems of the car.
Block location
Please note that the location of the electrical fuse module may depend on the type of equipment and year of manufacture of the vehicle. As a rule, this is the upper right part of the engine compartment, under the front windshield. The mounting block is made of plastic in the form of a rectangular box. To protect against accidental opening, the box is equipped with special latches. To open the module, you need to snap off the two protective brackets and lift the top plastic protection. Under the cover are all the main control relays and electrical fuses of the vehicle.
To quickly remove the fuse, special plastic pliers are located on the plastic protection cover. With their help, you can very easily get any element. You need to grab the top edge of the plastic case with pliers and carefully lift the element.
For the convenience of the user, on the top plastic cover there is a complete diagram, made in the form of a schematic image, which shows all the electrical fuses and relays indicating the current strength (A).
Fuse and relay diagram for injection models
Table 1. Explanation of fuses and relays 2114-3722010-60
№ | Current, A | Explanation of fuses |
F1 | 10 | Rear fog lights, rear fog light indicator lamp |
F2 | 10 | Turn signals and turn signal breaker relay. Alarm system. Hazard warning lamp |
F3 | 7,5 | Interior and luggage compartment lighting systems (interior lamp, luggage compartment lamp, ignition key illumination). Brake brake lamp, on-board computer backlight lamp. Engine control lamp |
F4 | 20 | Rear window heating control. Portable lamp connection socket |
F5 | 20 | Relay for monitoring and turning on the sound signal. Cooling system engine switch fuse and relay |
F6 | 30 | Control and relay switching on electric windows |
F7 | 30 | Electric motor control - heating system, interior heater, windshield washers, headlight cleaners. Interior cigarette lighter, glove box lamp. Turn on the heated rear window. |
F8 | 7,5 | Turning on the right fog lamp |
F9 | 7,5 | Turning on the left fog light |
F10 | 7,5 | Side light for the left side body, indicator light for turning on the side lights (on the display), lamps for illuminating the license plate and engine compartment, illumination lamp for switches, cigarette lighter, heater control levers. Instrument lighting switch. |
F11 | 7,5 | Right side body marker light |
F12 | 7,5 | Front right low beam headlight |
F13 | 7,5 | Front left low beam headlight |
F14 | 7,5 | Front left high beam headlight. Light indicator lamp. |
F15 | 7,5 | Front right high beam lamp. |
F16 | 15 | Body turn signals, relay-breaker for turn signals and hazard warning lights. Control relay and reverse lamps, indicator lamps for the on-board instrument control system, lamps for oil pressure, handbrake activation, brake fluid level, battery charge. On-board computer, engine generator winding. |
F17-F20 | Spares | |
№ | Relay circuit | |
K1 | Headlight cleaners | |
K2 | Turn signals and hazard warning lights | |
K3 | Windshield wiper | |
K4 | Monitoring the serviceability of brake light lamps and side lamps | |
K5 | Window lifters | |
K6 | Sound signal | |
K7 | Heated rear window | |
K8 | High beam headlights | |
K9 | Low beam headlights |
Decoding fuses and relays of block 2114-3722010-18
VAZ-2114, 2115, 2113 cars of the first models with a carburetor have certain differences in the fuse module.
Old style block fuse and relay diagram
Table 2. Decoding of fuses and relays of block 2114-3722010-18
№ | Current, A | Explanation of fuses |
F9 | 7,5 | Right rear fog lamp |
F8 | 7,5 | Left rear fog lamp |
F1 | 10 | Front headlight cleaners at the moment of switching on, wiper contacts, headlight washer switch valve, headlight wiper switch relay contacts |
F7 | 30 | Front headlight wipers during operation, winding of the relay for turning on the wipers, fuse for the interior heater, windshield washer, gearbox and timing controller for the rear window wiper, valves for turning on the front and rear washer, relay (winding) for turning on the engine cooling system, relay for turning on the rear window heating, glove box lighting, rear window heating control lamp |
F16 | 15 | Turn signal indicators and activation of hazard warning lights in turn mode, indicator control lamp, reversing lights, gearbox and relay for activation of windshield washers, generator winding (at startup), control lamps for brake fluid, oil pressure, carburetor flap, hand brake. "STOP" display lamp, voltmeter and coolant temperature indicator |
F3 | 10 | Interior lighting and rear brake light |
F6 | 30 | Power windows, power windows on/off relay |
F10 | 7,5 | License plate lights, engine compartment lamp, warning light on the dashboard (exterior lighting), instrument panel lights, cigarette lighter light, heating lever lights |
F5 | 20 | Relay for turning on the cooling system fan (electric motor), sound signal. |
F10 | 7,5 | Left front marker light Left rear marker light |
F11 | 7,5 | Right front headlight, right rear |
F2 | 10 | Hazard warning lamp, turn signals and hazard warning relay. |
F4 | 20 | Rear heated glass, heating on, portable socket, cigarette lighter in the cabin |
F15 | 7,5 | Front right high beam |
F14 | 7,5 | Front left high beam Light switch |
F13 | 7,5 | Left low beam |
F12 | 7,5 | Right low beam |
№ | Relay circuit | |
K1 | Headlight washers | |
K2 | Hazard and turn signals | |
K3 | Windshield wipers | |
K4 | Monitoring the health of lamps | |
K5 | Windows | |
K6 | Sound signal | |
K7 | Heated rear window | |
K8 | High beam headlights | |
K9 | Low beam headlights |
Additional items
Under the hood
Additional headlight wiper fuses (2A rating) protect the motor windings. They are located on the supply wires next to the gearmotors.
The starter activation relay 113.3747 or 90.3747-10 is located in the engine compartment on the right mudguard.
In the cabin
The windshield wiper relay (PC-514) is mounted under the panel on the left under the trim.
The ignition relay and the hazard warning and turn signal relays are installed on the front panel behind the instrument panel. The ignition relay (113.3747-10 or 90.3747-10) and the hazard warning and turn signal relays (23.3747 or 231.3747) have a bracket for direct mounting on the body.
The fog lamp fuse is located in the gear shift compartment, not far from the radio.
Starter, ignition, rear fog lamp relay
In order to carry out quick checks and repairs, the ignition system relay is installed under the front dashboard of the car, behind the hood release handle. It is located just below the central dashboard. The module is closed with a plastic plug, which must be opened slightly to test for functionality.
Starter, ignition, rear fog lamp relay
Next to the indicated relay, there is a similar one for the rear fog lights and the starter.
The main task of the relay when igniting is to reduce the applied load to the contacts. When the engine starts, the relay turns off some electrical circuits in the vehicle system. The system is used not only in injection, but also in carburetor engines.
In the event of a malfunction or malfunction in the ignition system, it is necessary to monitor the operation of the relay. For this purpose, open the box and carefully remove the desired element. It is attached using contacts to special grooves. The first thing to do is look at the oxidation of the contacts, if necessary, clean them with a soft cloth or treat them with a special liquid.
To check functionality, you need to use a regular multimeter. We connect to incoming connections and check the numbers. If there is no short circuit when current is applied, it means the element is not working. Replacement is carried out in a similar manner. It is necessary to use a standard element with the number of amperes indicated on the housing.
The device of wipers: what are they made of?
The device of the wipers is quite simple and consists of:
- trapezoid, transmitting movement from the motor;
- an electric motor driving the device;
- a pump that pumps washer into the device;
- tank for storing washer fluid;
- windshield wiper part with brushes at the end, mounted on a trapezoidal base.
Weak points of wipers
Weak points of wipers
In the entire device of wipers, the weakest point is the motor - its breakdown requires replacement. It is advisable to replace the relay along with it. The trapezoid can be restored in some cases. But what if the reason for the failure lies in the fuse or relay?
How to determine a faulty relay and fuse
The lack of movement of the wipers usually indicates a malfunction of the electric motor. Movement of the trapezoid while the glass remains dirty indicates damage to the pumping device or liquid tank.
Next, electronic faults are checked.
- When removing the instrument panel, you need to find the relay screwed to the body part.
- If the electrical elements do not work, the relay must be replaced - it cannot be repaired.
- You also need to check the fuse.
Front fog lamp relay
Front fog lights are not standard equipment on the model and are equipped depending on the configuration. The relay itself (if there are fog lights) is located in the engine compartment on the left mudguard.
Front fog lamp relay
Important! To access the relay, you must remove the battery! Without performing this manipulation, it will be difficult to remove and check its functionality.
Replacing a faulty element is very simple. You need to take a Phillips screwdriver (with a short handle), unscrew the bolt securing the relay to the car body, and check the element for malfunction. If it fails, we buy a new one and put everything in the reverse order.
Location of fuses on the diagram for VAZ 2110, 2111, 2112
Today we will look at the location of fuses in VAZ cars of the tenth family, namely models 2110, 21102, 21103, 2111, 2112. We will also show where the fuses and relays are located on the diagram and talk about the purpose of each of them and how to replace the fuses with your own hands. We will also touch on the most common problems with fuses among owners of these cars, diagnostic methods and replacement.
I would like to say that car electrical systems, in particular fuses and relays in the VAZ 2110, 21102, 21103, 2111, 2112, are quite reliable. The service life depends on operating conditions and timely diagnosis and replacement with high-quality components.
Let's figure out why fuses are needed in a car. First of all, they are responsible for the safety of the wiring and other systems of the machine. It is important to understand that each specific fuse is responsible only for its task and in the event of a short circuit or failure, a fire is practically excluded. A specific fuse blows and this does not cause a chain failure of other systems.
Depending on the problem of failure of any component or part of the car for which the electrician is responsible, you need to understand whether the car can be operated with this malfunction or not. The traffic rules contain a list of faults that you cannot operate a car with. If you discover, for example, that the headlights have failed or the wipers are not working at all, you should immediately correct the problem. Well, you can drive a car with non-working power windows. By the way, if someone suddenly needs a high-quality website for business, then these guys make good websites WebFormata.ru
Fuse layout diagram for VAZ 2110, 2111, 2112
The photo shows fuses for VAZ 2110, 2111, 2112
As you can see, each fuse is numbered with a corresponding index. In the above illustration, the unit is located on the left side of the steering column and is integrated into the instrument panel. Below are the values of the specific fuse in this mounting block.