The backlighting of the VAZ 2109 instrument panel is often not satisfactory for drivers. You can change the color and its brightness yourself, without turning to the salon for help.
To improve the lighting, you need to install LEDs instead of conventional incandescent light bulbs. Their glow is much brighter, in addition, you can choose the color of the backlight at your discretion: blue, green, red or white. These are the main colors, but if you look, you can also find purple LEDs.
Replacement of light bulbs or sockets must be carried out carefully and carefully. If the car owner decides to use LEDs to illuminate the buttons, then you need to purchase a light bulb with a regular base. Soldering and a special cartridge are needed if there is a desire to replace the backlight of the instrument cluster. Among the many LEDs, there are also those that have a diffuse or, conversely, point glow.
These effects are achieved using a focusing lens configuration. A more uniform backlight is suitable for illuminating the scale on the instrument panel, and a brighter light is suitable for the button icon. Every driver should take into account the features of design changes when improving his car.
Types of panels
Instrument panels on the VAZ 2109 are of at least three types:
- Low panel;
- High panel;
- Electronic panel on nines with Europanel.
On versions with a low panel, failure of the entire panel is extremely rare. This is due to the fact that here the speedometer and econometer are equipped with mechanical drives. Therefore, it is unlikely that they will fail along with the electrical component.
Messages 11
1 Topic by Andrey08 2009-12-16 13:01:12
Topic: Not Working: All Tidy, Wipers, Fern Guard on VAZ 21099
My friend has a VAZ 21099 injector.
And recently the following happened: all the instrumentation stopped working (speedometer, tachometer, etc.), the wipers and ferns do not work. the headlights seem to come on
Today I talked to him, they say in the morning everything worked fine, but in the afternoon it immediately turned off right on the go.
I advised him to pay attention to the fuse box (they say the frost has hit, condensation is forming or it’s just wet)
I would like to hear your opinion, what do you think about this? mb has this happened to anyone?
2 Reply from maik 2009-12-16 19:38:20
Re: Not working: All tidy, wipers, fern on VAZ 21099
My friend has a VAZ 21099 injector.
And recently the following happened: all the instrumentation stopped working (speedometer, tachometer, etc.), the wipers and ferns do not work. the headlights seem to come on
Today I talked to him, they say in the morning everything worked fine, but in the afternoon it immediately turned off right on the go.
I advised him to pay attention to the fuse box (they say the frost has hit, condensation is forming or it’s just wet)
Why doesn't it light up?
- First, remove the cover of the mounting block and make sure that the fuse is intact. The fuse markings are located on the inner surface of the cover. You should look for fuse F16 or F5, depending on the year of manufacture of your VAZ 2109.
- If the fuse is intact, be sure to check whether the contacts of the fuse you are looking for have not oxidized. It is not uncommon for shields to fail due to broken contact.
- Check if there is power to the dashboard. To do this, you will need a warning light and the ignition on. Disconnect connector X4 in the mounting block and check for voltage at pin 3. The disadvantage of the VAZ 2109 design is that when it rains, the mounting block immediately becomes wet. This causes oxidation of the contacts in the pads, which causes the electrics to stop working. Sometimes not only the contact is oxidized, but also the board of the Nine mounting block.
If none of the above actions yielded results, you will have to be disappointed. After all, now you need to remove the dashboard and check the condition of the wiring, contacts, and negative connections. Here it is better to trust a professional electrician or set aside a whole day to troubleshoot problems yourself. There is no need to rush here.
Additional lighting
You can decorate the interior beautifully with LEDs and make your car original, even on simple car models. For VAZ 21209 and VAZ 21093, interior lighting is often supplemented with footwell lighting. When opening the door, the power of the BSK light bulbs is not enough to illuminate the driver's seat in the area where the feet are located. The central lamp provides diffused light, but the steering wheel and front panel create shadows. Any accidentally dropped object will create inconvenience when landing in the dark.
Based on the location of the wiring, plus it is most convenient to connect from the cigarette lighter. The minus is taken from the BSK at the outlet to the interior light on the driver's door. Then the backlight will turn on when the front left door is opened. The directional light can be placed near the floor anywhere and create additional light for any passenger at the time of boarding.
A more complex option, when the connection is completely tied to the interior lighting. In this case, the negative wire is laid from the interior lamp, and the footwell lighting also works in the forced-on mode of the ceiling lamp.
Modern LED bulbs allow you to create various options for interior lighting tuning. You can make multi-colored indicators on devices or create panel illumination at any connection point. Passengers will be amazed when you turn on the many spotlights in the headliner. Due to their large number, weak light sources will ensure good visibility inside the car.
When creating unusual lighting, you must have certain knowledge and skills in installing DC electrical circuits. It is most convenient to connect to the wiring system from the junction under the trim to the left of the driver’s feet in front of the door.
Popular faults
If we talk about the dashboard of VAZ 2109 cars, then they are characterized by certain problems. We will tell you about them, and also tell you how to act correctly in a given situation.
| Fault type | Your actions |
| Gasoline level and temperature indicator does not work | In most percent of cases, this situation occurs due to breakdown of devices, sensors of these devices, or an open circuit of the power supply. Therefore, first check the circuit for continuity, make sure that the fuses have not blown. If this is not the case, check whether the gas level and temperature sensors are working. Only if none of the actions allowed you to get rid of the breakdown, you can begin to replace the devices themselves. No options, the problem lies in them |
| When the fuel tank is full, the arrow points to zero | If you have worked on the fuel level sensor, the fault most likely lies with you. When manipulating this device, the float limiter is often knocked down. Either the limiter is installed incorrectly or adjusted, causing the resistor winding to end. To resolve the problem, remove the sensor and then adjust the limiter again |
| The fuel gauge needle regularly jumps and ends up at zero | Here, most likely, the resistor has weak contact with the current collector. Another possible option is that there is a break in the resistor. To resolve this situation, we recommend replacing the hot level sensor with a new measuring device |
| The fuel level lamp is constantly on | If this lamp is constantly on, there is probably a short circuit in the fuel level sensor supply wiring to ground. Another option is that the sensor’s flexible bus is shorted to the fuel intake pipe. You will have to disassemble the device to align the bus and get rid of the resulting short circuit |
| Indicator lamps do not work on the dashboard | There is a high probability that the light bulbs have simply burned out, or they are poorly held in their seats due to loose contact. Replace the bulbs, but first try tightening the contacts. Traces of oxidation may be detected. When cleaned, the light bulbs can work normally again. Also, do not exclude the possibility of wiring breakage or oxidation of the tips of the supply wiring. Try going over the wires with a tester, cleaning the contacts if necessary. |
| The speedometer does not work, the flexible shaft is noisy | In such a situation, you will have to change the speedometer drive cable or replace the entire speedometer assembly. But before you bother so much, check that the fastening nuts of the tips are tightened correctly and properly. The flexible shaft may make noise during operation due to deformation or violation of the permissible bending of the shell of less than 10 centimeters during installation |
The instrument panel of the VAZ 2109 is not so complicated that you cannot figure it out on your own. But in the absence of experience, it is better to entrust the repair to specialists, or to enlist the support of a partner who understands this matter.
Didn't find the information you are looking for? on our forum.
Dismantling lighting
The diffuser is held on the base of the housing by a spring latch. Place the end of a flat-head screwdriver under the lampshade in the center and press lightly, removing the latch. After this, pull down and remove the glass cover from the lamp. Care must be taken to preserve the appearance of the lamp parts. Experienced specialists recommend placing a piece of cloth or paper on the end of the diffuser where you work with a screwdriver.
The light bulb can be removed and checked. Further dismantling is done using a Phillips screwdriver, the bolts that hold the plate and secure the base of the lampshade to the ceiling are unscrewed.
The four wires you disconnect should be labeled. Two of them are mass, and the obligatory “+” and “-”. When disconnecting wires, mark them so that there are no problems during assembly. If the new light is on, you don’t have to disassemble it any further.
The directional light canopy is removed in the same way, pryed off with a flat screwdriver and removed from the socket in the ceiling trim. Then mark the wires and disconnect them. Initially, all contacts are marked during assembly at the factory, but often when working in a cramped and poorly lit interior, the markings are difficult to see.
VAZ online stores, discounts for site users
Catalog of VAZ online stores by category:
- Accessories
- Spare parts
- Tuning
- Body kits
- Cases
- Studio
- Carbon tuning
- Flocking
Applications for adding new online stores to our catalog, please contact us via the feedback form. To receive a discount when ordering, indicate the code word in the note: lada2111.rf.
Online stores for VAZ accessories
Armrests, route on-board computers, radar detectors (radar detectors), acoustic components, automotive electronics, windshield wiper blades, shelves and podiums, antennas, chargers, stroboscopes, octane correctors, compression meters, voltage converters, etc. Website Description Discount for Lada2111.rf users
| timeturbo.ru (Tolyatti) | The TimeTurbo online store specializes in the sale of standard spare parts, accessories, as well as tuning of domestic and foreign manufacturers for VAZ cars | 5% |
| www.alamar.ru(Tolyatti) | Products from the leaders of Russian auto tuning: armrests, Euro handles, acoustic components, Garant locks and other means of protecting your car. Everything directly from the manufacturers: Alamar, TyunAuto, Flim, VS Auto, Security, Aden, Valentina, Jetter electronic, etc. | |
| www.vs.volga.ru (Tolyatti) | The largest manufacturer of shelves, podiums and boxes for subwoofers, etc. in Togliatti. | |
| www.neva-pl.ru(St. Petersburg) | The main profile is the sale of: route on-board computers, radar detectors (radar detectors), active antennas, tachometers, car chargers, stroboscopes, octane correctors, compression meters, voltage converters, etc. | |
| www.avtonomia.ru (Moscow and Ryazan) | The car accessories hypermarket offers goods for the interior and exterior of a car, children's car seats, car electronics, etc. | 5% on all goods |
| www.avto4avto.ru (Moscow) | Auto accessories from Germany, Japan, Russia and other countries for foreign and domestic cars. | |
| www.xenon55.ru(Moscow) | Car accessories that improve traffic safety and ride quality, and, of course, provide pleasure from driving a car. | 5% discount |
| tut-teplo.ru(Moscow) | A wide range of high-quality and fully certified equipment and components for the heating system. | |
| avtozercala.ru(St. Petersburg) | A wide range of car mirrors, mirror elements, as well as various components for car mirrors. | |
| autoComp.ru(Moscow) | The largest Russian online store specializing in the sale of goods for motorists | |
| www.msr.ru(Moscow) | A huge, constantly updated range of products for car tuning. | |
| www.12vi.ru(Kaluga) | CJSC Energomash specializes in the development, production and sale of automotive electronics products. | 5% discount |
| www.apel.ru(Tolyatti) | Various automotive electronics. | |
| a-service.narod.ru (Moscow) | JSC "A-Service" Car electronics, adapters for automatic light switching, smooth lighting switching, etc.. | |
| dda-viko.ru(Tolyatti) | Comfort and safety. Rain sensor DDA-7/15/25/35, fan control unit, etc.. | |
| www.balsat.ru(St. Petersburg) | Electronics for cars and professionals, devices for air conditioning and ventilation. | |
| www.farkop-magazin.ru (St. Petersburg) | Sale of additional equipment for cars: towbars, crankcase protection, roof rails. Delivery throughout Russia. | |
| www.karter.ru(St. Petersburg) | "Metalproducts" is a high-tech innovative company specializing in the development and production of automotive accessories and additional equipment (towbars, crankcase protection, roof rails, car mats, tuning and individual development of protection). |
Online stores for VAZ spare parts
Balls, ends, rods, silent blocks, brake pads, CV joints, boots, bump stops, wheel bearings, stabilizer struts, filters, pan gaskets, oil seals, timing belts, cylinder head gaskets and valve covers, oil seals, sensors, pistons, rings, components for starters , generators, power steering, injectors, body elements, interior elements, optics and other assortment of auto parts and components. WebsiteDescriptionDiscount for Lada2111.rf users
| timeturbo.ru (Tolyatti) | The TimeTurbo online store specializes in the sale of standard spare parts, accessories, as well as tuning of domestic and foreign manufacturers for VAZ cars. | 5% |
| www.postavto.ru(Tolyatti) | The entire range of auto parts and components offered, from standard spare parts to tuning. | 3% |
| www.avtoall.ru(Moscow) | The widest range of spare parts in Moscow for cars and trucks of various brands of domestic and foreign production, spare parts for buses and special equipment is available. | |
| www.exist.ru (branches throughout Russia) | Auto parts for cars, as well as accessories, oils, tires, wheels and much more - in total more than 26 million items, auto parts to order and in stock. Foreign cars. | |
| pasker.ru(Moscow) | Assortment of more than 25,000 types of auto parts. Wholesale sale of auto parts for cash and non-cash payments from a warehouse in Moscow. |
xn--2111-43da1a8c.xn--p1ai
VAZ 2109 stop light on the instrument panel | Topic author: Fawziyya
The red stop light is on on the instrument panel, but not the handbrake. Initially it was blinking. Previously, this only happened when the car almost stalled, for example, now it lights up even when the engine is running normally. What is the reason? Has anyone encountered this?
Alexander (Aibhlinn) Try topping up the brakes
Konstantin (Jeronym) is almost at minimum..)
Yurets (Saskia) agrees with Alexander.
Sanya (Melbah) do you need brakes and that’s it?
Denis (Hillard) share! and most likely the pads have worn out
Taras (Haniel) What does the brakes have to do with it. Maybe his oil pressure light comes on along with the stop light.
Evgeny (Amana) same problem, stop and oil pressure lights up at low speeds, oil level is normal!
Evgeny (Amana) this happened after the engine was rebuilt, maybe something was done wrong with the oil pump during installation?
Evgeny (Amana) before the engine repair nothing was burning, they went through everything, restored it, I started the temperature, everything started blinking, stop and oil pressure, before the repair it didn’t blink and nothing was clogged!
Maxim (Fauzi) clean the oil receiver.
Igor (Ester) look at the button on the handbrake!!
Yury (Jaganu) Does the car keep speed normally? Doesn't twitch at idle?
Svetlana (Beaufort) What if the stop light is on and the size indicator is below? Zhizhka have new brake pads and the handbrake switch do not dull the oil normally?
Svetlana (Beaufort) Denis, dressed
Alexey (Vivasvata) hello, the problem is this: when starting the car, it works fine, nothing lights up, after driving, when the temperature is about 90 when the car stops, that is, at idle the stop and oil can begin to blink, (the oil is normal) if you give the gas a little, it disappears, When you start moving, the oil and filter are changed too, maybe someone has had this problem, tell me what to do
Svetlana (Beaufort) Yuri, twitchy at idle and when driving
Maxim (Fauzi) if it twitches, then most likely change the idle speed sensor,: - issue price 150 rubles
Maxim (Fauzi) I have the same problem with the stop, so I read it and figure out what’s what)
Nariman (Nicole) I have a stop blinking on the panel and after stopping, as soon as you turn off the car, it still won’t start. But when I try to start it with the same Akum, the starter clicks and the panel goes out. And during the night it’s been parked, it’s already killed 2 new Akums. With it running when you turn on the headlights and heater, both work poorly
