VAZ 2114 cigarette lighter does not work - how to remove, replacement, repair

All manipulations with on-board vehicle electronics, including the cigarette lighter, should be performed after the power terminals are removed from the battery.

Removal is carried out according to the following scheme:

• the left screen of the center console is dismantled;

Removing the torpedo screen

• the block with the wiring harnesses suitable for the cigarette lighter is disconnected;

Disconnect the block with wires

• the light bulb responsible for illuminating the ashtray is removed (along with its socket and a suitable cable harness);

Disconnect the backlight bulb

• before pulling out the cigarette lighter of the VAZ 2114, you should lightly pick it up by the edge with a flat screwdriver or a strong small knife and pull it, then push it out of the console;
• the light filter is disconnected along with the backlight bulb socket;
• if it is necessary to replace the cigarette lighter lamp, it is also necessary to remove its reflector;
• After this, all that remains is to remove the lamp socket and remove the burnt out lamp itself.

Removing the cigarette lighter

Assembling the entire device, as well as its installation (or installing a new cigarette lighter to replace a completely broken one) is carried out in exactly the same order, but in reverse order.

Thus, as you can see, the entire process of removing, installing, and repairing the cigarette lighter does not pose any difficulties.

Useful video

The only thing that should be advised to those who decide to install a completely new device to replace a damaged one is that when buying a cigarette lighter in a car store, be sure to check it for open circuits using a multimeter. This is due to the fact that recently cases when a newly purchased device turns out to be completely faulty have become very frequent.

Published January 17, 2018

REMOVAL AND INSTALLATION OF CIGARET LIGHTER

You will need a screwdriver.

1. Disconnect the wire from the negative terminal of the battery.

2. Unscrew the screws and remove the left trim of the center console of the instrument panel.

3. Disconnect the wiring harness block from the cigarette lighter.

4. Remove the ashtray illumination lamp along with the socket and wiring harness block.

5. Overcoming the resistance of the clamps, push the cigarette lighter out...

6. ...and remove it from the center console.

7. Then remove the light filter assembly with the backlight lamp socket.

8. To replace the cigarette lighter lamp, remove the reflector...

10. ...and remove the backlight lamp from the filter socket.

11. Install the cigarette lighter in the reverse order of removal.

Connecting the cigarette lighter

Never connect the cigarette lighter to the ignition switch. The ignition system will not withstand such a load. Having laid the wire in the engine compartment, bring it to the positive terminal of the battery, connect the fuse and then attach it to the terminal. If for some reason you cannot do this, run a wire with a fuse to the starter and attach it to the positive terminal of the relay. Strip the end of the wire at a distance of 1 cm, place it on the terminal, then crimp it using pliers. Be sure to secure the wire so that it does not dangle anywhere. To attach the wire to the cigarette lighter, use a soldering iron or an appropriate terminal, depending on the device model. Install a fuse and a switch next to the cigarette lighter, this will increase the safety of using this device.

Do not confuse the arrangement of parts of the diagram:

1. Battery.
2. Fuse.
3. Switch.
4. Relay.
5. Cigarette lighter.

The switch must be designed for a current of 1.5 times the maximum load. If there is no such switch, attach a relay next to it that is suitable for the current. Some drivers place a switch and relay next to the ignition switch. Connect the switch to the control contact of the relay, and the cigarette lighter to the power one. To do this, place heat-shrink tubing on the exposed ends of the wire, then push and crimp the terminals. Adjust the tube so that it completely covers the junction of the terminal and the wire, then heat it with a match or lighter. You can also install a regular cable splitter (220 volts), which is sold in hardware stores. Find the nearest ground connection location (the wire is bolted directly to the body). Unscrew the bolt, clean the contact pads of the terminal and body. Route a piece of wire from the relay and cigarette lighter to the ground hole to determine the length, then cut and strip the ends.

Make a splitter - take a piece of wire of a suitable length, strip both ends. Then solder the ends of the long and short wires to each other so that they both point in the same direction. Protect the connection with heat shrink tubing, then attach the connection terminal to the negative of the cigarette lighter. Position the tube so that it completely covers the contact point. Place heat shrink tubing on the other end of the short wire and attach the terminal. Or use a regular cable splitter, which must be rigidly attached to the body.

Installation check

Check all connections carefully. The relay and splitter must be securely attached to the housing. After making sure that everything is in order, check that the ignition switch is turned to the off position and connect the battery. Using a tester, measure the voltage on the unconnected battery. Place the negative terminal on the corresponding battery terminal and measure the voltage again. If it hasn't changed, then everything is fine. If it drops by at least 0.5 volts, turn all electrical appliances on and off, including the ignition system. If the voltage does not rise, disconnect the battery and look for a short circuit. If everything is fine, turn on the switch and measure the voltage on the battery again. After making sure that everything is correct, measure the voltage at the cigarette lighter contacts. If everything is in order, you have successfully completed the job.

The cigarette lighter is an essential attribute of any car. Often there is a need for an additional cigarette lighter, located in the trunk or on the panel, next to the main one. Through a splitter you can connect up to 3 different devices to one cigarette lighter. The additional cigarette lighter is connected directly to the battery. After reading the article, you will learn how to connect the cigarette lighter in your car correctly without harming your car.

How does a cigarette lighter work?

A car cigarette lighter is two devices - a heating element and a connector (plug) in a convenient housing. It can be directly connected to the battery, so the device works even if the ignition switch is turned off. In addition to its main purpose, the plug is often used as a 12/24 volt outlet to which a splitter is connected to provide power to a laptop, phone or other devices. A splitter is also connected to it, so you can simultaneously charge a laptop, phone, or use a DVR. The power splitter or power supplies of these devices are inserted into a plug that provides a reliable connection to the cigarette lighter socket contacts.

What you need to insert a cigarette lighter

If you decide to install an additional cigarette lighter, you will need the following tools:

• drill;
• set of metal drills;
• metal crown, the diameter of which corresponds to the selected cigarette lighter;
• round and flat files;
• soldering iron;
• solder;
• rosin;
• pliers;
• side cutters;
• Screwdriver Set;
• heat-shrink tubing;
• switch;
• fuse;
• the wire;
• a regular cable splitter (220 volts) from a hardware store

How to change the low beam bulb on a VAZ-2114: photos and videos

Many car enthusiasts have encountered the fact that one of the low beam lamps on a VAZ-2114 went out. Why does this happen? The answer is quite simple - the light bulb has burned out and needs to be replaced. Many motorists will ask the question - how to do this? Quite simple, and this article will walk you through this simple process.

A video on how to replace a low beam lamp on a VAZ-2115 (by analogy, replacement on a VAZ-2114 occurs) below:

The video will tell you how to replace the low beam lamp in a VAZ-2114.

Replacing the low beam lamp on a VAZ-2114

Low beam lamp.

One of the simplest car repair processes is replacing headlight bulbs.

For the 14th VAZ model, low and high beam are the same thing. Lamp type - h5.

The lamp replacement process itself takes 3–7 minutes, depending on the skill of the motorist. So, let's consider the sequence of actions:

1. Unscrew the screws securing the lamp protective casing and remove it.

Remove the lamp protective cover.

Disconnect the wire block.

Disconnect the wire block from the lamp.

Compress the fixing spring of the lamp mount and remove the holder.

Unclip the lamp clamp.

Next, take out the lamp and insert a new one.

We remove the low beam lamp from its seat.

We carry out the assembly in the reverse order.

Lamp selection

The choice of low beam lamps for modern cars is quite large, since the further into the forest, the more advanced the technology becomes. So, let's look at what types of lamps are installed on the VAZ-2114.

Standard lamps

The manufacturer recommends installing lamps with the H4 rating in the headlights of cars of the 2113-2115 series. But, as practice shows, the applicability of other headlights has increased and it is already possible to install H1 as the main light.

Halogen

This is how halogen lamps shine!

A common option for light bulbs for areas with frequent fog.

They are ideal because they are visible from afar. The main representatives can rightfully be considered: Osram and Philips.

Xenon

This is how xenon shines on a VAZ-2114!

10 years ago, xenon technology began to be introduced en masse. Today, no one will be surprised by the presence of xenon lamps in a car. The automotive market for additional equipment provides a wide selection of such equipment that even the cheapest cars began to install such lamps.

How to remove the cigarette lighter to replace a light bulb.

How to remove the cigarette lighter to replace a light bulb on a VAZ 2114?

I was about to change a burnt-out lamp in the cigarette lighter, I even almost pulled it out, but I couldn’t get it out completely. How to get it out? Wrap a thin wire around it, crimp it and pull. There are two latches. Tanya There are wire cutters and wrenches. hammer at last. If you've almost pulled it out and it doesn't go any further, you'll have to remove the panel. Somewhere the power wire is pinched. Vetos https://alllada. net/pyatnashka/15/vaz2115. TintoTam you first need to pull out the metal case. To do this, you need to press some kind of antenna. Look what he's holding. When assembled with a plastic ring (green), it will not come out. Diona with a grinder cutter or chisel Alfredon just can’t be pulled out - you need to remove the whole beard! Danian How to remove the starter on a VAZ 21072? instructions for the kettle are needed There is no power from the ignition switch to the starter. What could be the reason? VAZ-21072VAZ 11193 "KALINA". The battery died and after replacement it will not start. no indica ENGINE, the starter does not turn, the fuses are intact, how to open the hood if the cable has come off on a VAZ 11193 (Kalina) please help VAZ 1119 Kalina engine 1, 4 16V if the timing belt breaks, does it bend the valves?

Where is the cigarette lighter fuse located?

It is on the four that the fuse is located in the mounting block located in the engine compartment. You can see it when you open the hood. The block is in the right corner.

Checking for damage

To check for a cigarette lighter malfunction, we will need:

1. Two screwdrivers (one Phillips, one slotted);
2. Soldering iron;
3. Two tweezers (one curved, the other straight);
4. Toaster for cars;
5. Pliers.

Replacing the light bulb in the cigarette lighter of a VAZ 2114, repair instructions with video

Answer to the request on demand in the topic of replacing a light bulb in the cigarette lighter of a VAZ 2114 - click. Do-it-yourself car repair with photo and video guides, all this for those who have to repair their car. How to repair a car yourself at home. We will help you with repairs and repair the car yourself. We know how to restore a car with minimal investment. I have attached video instructions.

Category: DIY repairs

Laughter in the topic: Morning. Bus. A man stands drunk and can barely stand on his feet. Some granny is grumbling. — It’s early morning and I’m already drunk! The man turns to her. - Why should I go to work without eating? Yes ?

Published by Admin: at the request of Eremey

Car owner assessment: Let's start with the positives) Exterior. This car has the most attractive design of all crossovers in its class.2) Interior. I had to sit in many cars. But if you choose between Sportage, ACX, Honda SRV, Tiguan. The ix35 has a cut above comfort inside. 3) Quite good sound insulation. Moreover, since 2014 they have made it even better. There are some bugs, but I fixed them with my own hands.4) Huge selection for tuning. Thank God, there is a bunch of all sorts of junk for our car on Chinese sites, starting with a key case (very nice by the way) and ending with body kits. For the same acx there is no nichrome. Regarding the suspension. Many people here complain that they changed the racks in a circle. I've never had any problems. This really bothers me and every month and a half I go to have the suspension inspected, the price is pennies. 5) Dynamics. It seems like there are only 150 horses, but these ponies are enough for the city and the highway. We don't have a sports car. Do you want to drive? Buy gtr.6) Consumption. Many people also write about the huge expense. In my “home-work” mode it is 10.5. That's not a lot.

Why did the cigarette lighter stop working?

The device can break down for a number of reasons. In some cases, you can repair it yourself, and sometimes you need to completely change the cigarette lighter.

How to change the light bulb on the cigarette lighter of a VAZ 2114

Video on demand on how to change the light bulb on the cigarette lighter of a VAZ 2114 - we are waiting for you to visit us, go ahead. Videos and reviews on do-it-yourself car maintenance and repair. How to repair a car yourself at home. We will help you with repairs and repair the car yourself. We know how to restore a car with minimal investment. I have attached video instructions.

Category: Car repair

Laughter on the topic: - Do you want a fairy tale about a tiger, an elephant and a rabbit? - How about a pig? - About a pig? You can also talk about the pig... Once upon a time there was a Tiger, an Elephant and a Rabbit... - And the pig? - And then they got the mumps!

Published by Admin: at the request of Corradoa

Criticism of the car owner: The car is strong, practical, moderately comfortable... If maintained correctly, it does not rust at all. “Holds the road” perfectly. Consumption on the highway is up to 6.5 liters, in the city a little more than 9.0. The car is fully adapted for our roads and operating conditions, both in terms of suspension and interior strength, and in the unpretentiousness of the engine to operating conditions. The interior, despite its external dimensions, is quite spacious. Very practical for the city. You can transport large items in the cabin: there was a case when I was once transporting an old Saratov refrigerator to my neighbor’s grandmother, with the rear seats folded down and the back door closed. The three-door car is convenient because when transporting your granddaughters to nature, you are not afraid that the rear side doors will accidentally open. Spare parts are not a problem, the difficulty of repairs is that I have never contacted the service (except for diagnostics using the on-board computer), everything is very simple. In winter it starts at any frost (up to - 45) without warming up. The interior is very warm in winter... It doesn’t heat up in summer. I wanted to sell it twice, but changed my mind: for the harsh operating conditions in which my Golf is used, I don’t yet see an alternative. Golf 5 - capricious...

Before we look at the main topic - how to remove the cigarette lighter of a VAZ 2114, you should first find out - what is a cigarette lighter, where is it located and how to use it?

A car cigarette lighter is a special electrical device, usually located on the front panel of the car and used for lighting cigarettes (hence, as you might guess, the name), as well as connecting various electrical appliances and tools (more precisely, they are connected to the cigarette lighter socket, and not into the cigarette lighter itself, which is only a removable part. However, in most cases, both parts of this device are called the same...)

The removable part, which serves for lighting the cigarette, is also designed quite simply - it contains bimetallic contacts and a conductive spiral, which heats up when connected to the network (the vast majority of cigarette lighters also have a button that turns the heating process on and off, which protects the device from quickly burning out (in case the heating was constant...)

Can it be used as a car socket?

Most often, car owners use the cigarette lighter socket as a connector for connecting additional electrical equipment. The most common devices:

• DVR;
• GPS navigator;
• fan;
• compressor pumping up the wheels;
• charging for mobile devices (phones, tablets, laptops).

When using the glass as a 12-volt outlet, the maximum power of the connected devices should not exceed 360 Watts. Calculated using the formula P=I*A, where I is the voltage of 12 volts, and A is the maximum current of 30 amperes.

Problems with the cigarette lighter and their elimination

Very often, especially in cases of constant operation or increased loads on the connector, the device fails. In some of these cases, the only solution will be to replace the VAZ 2114 cigarette lighter, while in others, you can try to fix this problem by repairing it.

Before you begin dismantling the cigarette lighter or starting to repair it, you should check the reliability of the connection of the wiring harness suitable for it. This can be done by checking the tightness of the fasteners in the block (it is designated as X1).

• poor contact in the connector;
• oxidation of connector contacts;
• fuse blown;
• burning or melting of connector contacts;
• backlight bulb burnout;
• a short circuit in the system that occurs when third-party devices are connected;
• mechanical destruction of the connector.

In the first three cases, you can still try to correct the situation, in the rest you will have to dismantle the device and, except in the case of a burnt-out light bulb, purchase and install a new one in its place (it should be immediately recalled that before changing the cigarette lighter on a VAZ 2114, you should disconnect the battery ).

As for poor contact inside the connector or the presence of oxides, you can try to solve this problem by slightly bending the contacts themselves and cleaning them. If a fuse blows, you just need to replace it with a new, similar one (the fuse you are looking for is designated in the row of fuses as F4 and is designed for a maximum current of 20 amperes).

Typical faults

Where to look for the reason if the VAZ 2114 cigarette lighter does not work? It is necessary to take into account that the failure of the AP, as well as the sockets directly for connecting it, are two different things. Moreover, the AP is not used as often as a socket, since this socket is often used to connect various electronic devices. The device may stop working when using low-quality chargers for equipment made in China. Especially when it comes to using an AP splitter, this can, in principle, cause its breakdown (the author of the video is the Expert R channel).

The AP circuit is designed to power various gadgets, but its maximum load capacity is 20 Amps. The corresponding 20 A fuse element is located in the block and is marked with the symbols F4. If you use a splitter, the load on the circuit will be simply catastrophic and over time the fuse will fail, but this is not so bad. It is much worse if the wiring fails, since this can cause not only a short circuit, but also a fire.

It often happens that if the cigarette lighter stops working, the radio does not work. In this case, the problem most likely lies in the circuit or functionality of the safety element. The radio can be connected directly to the battery or to the AC cable, so you shouldn’t be surprised at its inoperability if the latter breaks down.

How to remove the cigarette lighter and install a new one?

The entire process of dismantling a broken cigarette lighter and installing a new one in its place will not take much time (and also will not require a large number of tools - one screwdriver will be enough).

All manipulations with on-board vehicle electronics, including the cigarette lighter, should be performed after the power terminals are removed from the battery.

Removal is carried out according to the following scheme:

• the left screen of the center console is dismantled;

Assembling the entire device, as well as its installation (or installing a new cigarette lighter to replace a completely broken one) is carried out in exactly the same order, but in reverse order.

Thus, as you can see, the entire process of removing, installing, and repairing the cigarette lighter does not pose any difficulties.

What kind of cigarette lighter is on the fourteenth Samara model?

Early VAZ models (2101-2109) have an old-style device with a long tip. This cigarette lighter has a number of disadvantages:

• over time it begins to wobble in the nest and may stop working;
• does not provide reliable fixation of the plugs of connected devices.

The VAZ 2114 car has a different modification of the cigarette lighter - a short body modeled on the European standard. The original part has article number 212337251113725, and its price is 300 - 600 rubles. There are cheaper analogues of cigarette lighters, but such modifications should be abandoned - their performance does not last long. It is important that the part is carefully packaged, and the product is completed with certificates of conformity and quality passports.