Changing the oil in a Nexia gearbox: how to change the oil in a Nexia gearbox

Checking the level and changing the oil in a manual transmission Daewoo Nexia N150

Tools:
Parts and consumables:

Notes:

Check and, if necessary, replenish the oil level in the gearbox every 10 thousand kilometers or 6 months. operation.

Check the oil level in the gearbox no earlier than two minutes after stopping the engine. Carry out the work on an inspection ditch or overpass.

Checking the gearbox oil level

1. Using a 13 mm spanner, unscrew the inspection hole plug located next to the inner joint of the right wheel drive in the gearbox housing and remove it.

2. Insert your finger into the hole and check the oil level.

Note:

The normal oil level is at the bottom edge of the hole.

3. If there is insufficient oil, remove the breather cap.

4. Unscrew the breather with a 17 mm wrench and remove it from the hole in the gearbox housing.

5. Clean the metal trap of the transmission inspection plug.

6. Use a syringe to add oil to the Nexia gearbox to the bottom edge of the inspection hole (see point 2). As soon as the oil starts to come out through the inspection hole

7. Tighten the breather and inspection hole plug.

Changing the oil in the Nexia gearbox

Note:

The Daewoo Nexia N150 gearbox is filled with oil for its entire service life. Only the instructions are silent about the length of the period, so presumably it is 100-150 thousand km, or 7-10 years of operation. In any case, even on a new car, it is recommended to replace the mineral water poured into the box with synthetic water.

Even during the operation of the car, it may be necessary to drain the oil and replace it, for example, when repairing a gearbox or when there is a significant oil leak from the gearbox, when it is not possible to add oil of the same brand that was poured into the gearbox. It is recommended to change the oil when the gearbox is warm.

1. Clean the bottom cover of the gearbox from dirt. Place a wide container with a capacity of at least 3.5 liters under the lid.

2. Using a 13 mm socket, unscrew the ten bolts securing the cover partly and drain the oil into a substitute container.

3. After draining the oil, completely unscrew the bolts and remove the cover. Clean it from deposits, wear products of gearbox parts and traces of the old gasket, and also clean the mating surface of the gearbox housing.

4. Then put the gear in neutral, chock the rear wheels, apply the parking brake and jack up the front left wheel to drain any remaining oil from the 5th gear housing.

Note:

You need to jack it high (to the height of the jack, maybe even more). Rotate the left front wheel backwards, and more old oil will spill out.

In this way, approximately 1.7 liters are drained, with a total volume of oil poured into the gearbox of 1.8 liters.

5. Lower the car.

6. Replace the transmission cover gasket with a new one.

7. Screw in the bolts and tighten them evenly to the specified torque.

8. Fill the transmission oil into the gearbox to the required level, as described in the first part of the article.

The article is missing:

Source

Instructions

Changing the oil in the gearbox is carried out on an overpass or pit. The replacement procedure includes the following steps.

Steps 1-3

4-7 steps

Step 8

Steps 9-11

1. If there is engine protection, remove it.
2. Using a 10 mm socket, loosen the transmission pan bolts.
3. We tighten the bolts in the front part of the pan and place a wide container under the drained oil.
4. After draining all the lubricant, completely remove the pan. In this case, even if the gasket does not break, it is recommended to replace it.
5. Usually only 1.5 liters of oil is drained, and 200-300 g continues to remain in the crankcase. To completely drain, you can raise the front left wheel to the maximum height possible with a standard jack.
6. Using a 13 mm socket, unscrew the oil level plug on the right side of the gearbox under the inner CV joint. Then we thoroughly rinse the plug itself from the inside, as well as the loose magnet located in its cavity.
7. After waiting until oil stops dripping from the gearbox, we install the pan in place, thoroughly cleaning its seat from old grease and gasket residues. The pan is installed with a new gasket or sealant, without tightening the control plug.
8. Next, you can fill in new gearbox oil. To do this, twist the breather in the upper part of the gearbox, next to the selector mechanism. Remove the plastic cap from the breather and unscrew it using a 19 mm wrench.
9. For convenience, insert a funnel into the breather hole and slowly add oil until it begins to flow from the plug hole, then tighten the control plug. As a result, about one and a half liters of lubricant is poured.
10. If the front left wheel was lifted to completely drain the fluid, then after closing the plug, add oil to the nominal volume. Otherwise, there is no need to perform additional filling.
11. All that remains is to screw the breather back to its original location.

At this point, replacing the fluid in the Daewoo Nexia gearbox can be considered complete. There is nothing complicated about this, all that remains is to check and make sure that the gears change easily enough, regardless of the time of year.

Changing the oil in the Daewoo Nexia gearbox yourself

Normal operation of the gearbox is impossible without lubricant. Thanks to oil, rubbing components and transmission elements do not wear out so quickly. This is why the fluid should be changed periodically. How to change the oil in the Daewoo Nexia gearbox and what will happen if you do not replace the lubricant on time, you can find out from this material.

How often does an oil change need to be made?

Which oil is better to choose?

How much should I fill?

Consequences of untimely replacement

Level control and topping up

How to change the lubricant yourself?

Video “Visual instructions for changing the oil in the Nexia gearbox yourself”

Comments and Reviews

How often does an oil change need to be made?

To begin with, we suggest you sort out the question of when to change and fill new fluid into a manual transmission of a Daewoo Nexia 150 2011 or another year of manufacture. According to official data from the automobile manufacturer, the oil initially poured into the transmission at the factory must be used throughout the entire life of the vehicle. But the manufacturer also does not specify what the specific service life of the car should be. Therefore, the car owner will not be able to check whether this resource has expired or not.

Nexia gearbox

In order to prevent serious malfunctions in the operation of the Daewoo Nexia gearbox and avoid large financial costs, it is recommended to change the transmission oil after 100-150 thousand kilometers. Or every 7-10 years. If there are malfunctions in the operation of the unit or difficulties with switching speeds, the fluid can be changed earlier. The best option is to replace it every 100 thousand kilometers.

Features of Daewoo Nexia

Daewoo Nexia is the most recognizable car that began to conquer our market back in 1992, thanks to which its name has become a household name. Since the release of the first model, Nexia has experienced two restylings, the last of which was carried out 10 years ago.

The popularity of the model is explained by its cost, which is quite competitive, because there are no other explanations for such demand. Its sales are not falling even today.

The most successful version of Nexia are models produced after 2009. The second restyling was beneficial, this was especially reflected in the engines - eight-valve, 1.5 liters and sixteen-valve, 1.6 liters. volume.

The second one came from the Chevrolet Lacetti, its power was 109 “horses”, and it was he who received approving reviews from grateful owners. At that time there was only one gearbox - a 5-speed manual.

Nexia engine oil

As for brands that produce oil, Nexia owners have a wide choice. The manufacturer does not make any clear recommendations. The only condition is compliance with the viscosity characteristics. This indicator is determined in accordance with the climate and the level of average load on the engine.

Requirements

• The engine can be filled with both semi-synthetic and synthetic oil. The use of mineral water is not recommended.
• According to API standards, the oil must have a level above SM/CF.
• 5W-30 is used exclusively at average temperatures below -20℃.
• The average climate zone allows the use of 5W-40 and 5W-50.
• For southern regions, preference is given to 5W-50, 10W-40 and 10W-50.

Volumes and timing of replacement

As for the amount of oil that needs to be poured into the Daewoo Nexia engine, it is the same for both types of internal combustion engines - 3.8 liters, the only difference is that the 16-valve engine needs a little more - 150-200 grams. This is where the technological features of the engine components and assemblies affect.

The lubricant should be changed every 10 thousand km (about a year) - this is regulated by the manufacturer’s standards. Even if Nexia is idle most of the time, this does not affect the timing in any way - the oil deteriorates over time and its quality is lost.

If the car is used in harsh conditions, then the replacement period is reduced by half.

Oil for Daewoo Nexia box

The official data provided by the manufacturer does not contain any information about what kind of oil to pour into the Daewoo Nexia box, since they believe that the oil filled at the factory cannot be replaced for the entire period of operation of the vehicle.

However, it does not say anything about what this period should be - the owner himself determines the operational capabilities of the machine.

Based on the experience of Nexia owners, we can conclude that if there are no difficulties in the operation of the gearbox, the gears shift smoothly and easily, then you don’t have to think about changing the oil in it until the mileage is 100-150 thousand. If difficulties arise, it is better not to delay the replacement , it's cheaper.

Since the Nexia service book does not contain information about transmission lubricant, it must be replaced based on information from more experienced owners. There is no difference between 8 and 16 valve cars; the same thing can be filled in in both cases.

A longer service life is shown by gearboxes that have been filled with synthetic or semi-synthetic lubricant. At the factory, Nexia is filled with mineral oil, so after purchase, the lubricant must be replaced immediately.

In general, the selection process is similar to the selection of engine oil - weather and climatic conditions, as well as operating conditions:

• temperate climate – 80W GL-4 of any manufacturer;
• northern latitudes – 75W90 GL-4 (-25℃ average).

Which oil manufacturer (both for the internal combustion engine and for the gearbox) to give preference to is chosen by the owner of the Daewoo Nexia, based on his own preferences and the thickness of his wallet.

Source: https://prem-motors.ru/kakoe-maslo-zalivat-daewoo-nexia/

Which oil is better to choose?

When changing the oil in a Daewoo Nexia n150 gearbox with 8 or 16 valves, you need to know what kind of lubricant should be poured into the system. The manufacturer does not regulate this replacement. Accordingly, you will not be able to find information about choosing a product in the service book. Practice shows that Daewoo Nexia gearboxes whose owners fill with synthetic or semi-synthetic lubricant last a long time. Initially, when a car is manufactured, mineral oil is used in the gearbox, so when buying a car it is also better to change it to “synthetic” or “semi-synthetic”.

Transmission fluid MANNOL Hypoid Getriebeoel 80W-90 API

What oil do you recommend to put in the gearbox?

The description for the car says: The gearbox oil does not require replacement for the entire service life of the gearbox. If necessary, ensure that the oil level is at the bottom edge of the filler plug. I have a 2004 car, mileage 17,700 km, I’m only going to check the oil level in the gearbox in the spring, top it up if necessary, but I’m not going to change it! If the factory instructions say so, then it’s not just a paper of morality!!!

Reply with quotation

«Axle shaft assembly for 4-speed automatic | grinding valves with drill or manually»

Related topics

• Tell me what kind of oil to put in the engine.

  from Vetal086 in the Engine and transmission section

  Answers: 23

  Last message: 02/14/2016, 02:26

• Tell me what transmission oil is best to pour into the box.

  from Tom po in the Engine and transmission section

  Replies: 71

  Last message: 12/22/2012, 11:14 pm

• So what kind of oil goes into the box - GL4 or GL5?

  from Nomemory in the Engine and Transmission section

  Replies: 56

  Last message: 06/13/2011, 19:11

• What kind of oil should I fill the automatic transmission?

  from Doogy in the Engine and transmission section

  Replies: 0

  Last message: 03/15/2011, 19:03

• What oil should I fill?

  from barmaley9 in the Engine and transmission section

  Replies: 10

  Read also:  Traction from the cylinder to the lock 2109. Repairing car locks - a motorist’s guide

  Last message: 03/17/2009, 12:24

Your rights

• You cannot create new topics
• You cannot reply to topics
• You cannot attach attachments
• You can not edit your posts

• BB codes On
• Smilies On
• Code On
• Code On
• HTML Code Off

Forum Rules

How much should I fill?

It is equally important for owners of these car models to know how many liters are poured into the transmission. Service books for cars that require replacement of this consumable usually contain a table with fill parameters. In the case of an 8- or 16-valve Nexia, there is no such information in the service manual. However, before changing, you need to consider how much lubricant to pour into the gearbox.

As for volume, the transmission of the Daewoo Nexia should contain about 1.8 liters of oil.

History of Nexia

This Korean middle-class car was presented to the public in 1986. The development was carried out by German specialists (). The car was created on the basis of the Opel Kadett E, which was widespread at that time. "Nexia" began to be produced for residents of developing countries. Since 1995, cars have become available to citizens of the former Soviet Union. By the way, this car is known to Korean residents under the name “Daewoo Cielo”.

Ergonomics of Daewoo Nexia

The car stood out, first of all, for its low price. It cost no more than Russian front-wheel drive VAZs. The car was quite reliable, unpretentious in use, was ahead of Russian cars in terms of these characteristics and was not inferior to imported middle-class models. Replacing broken parts was easy due to their availability. All this explains the ubiquity of this machine.

However, Nexia gradually began to lose ground. The last car of this model was released four years ago. After this, the Korean manufacturer began producing the Daewoo Gentra.

Consequences of untimely replacement

8- and 16-valve Daewoo Nexia requires periodic replacement of transmission oil, since the additive package in the lubricant loses its properties over time. As a result, it becomes inoperable. Because of this, the liquid cannot provide the proper level of protection for rubbing surfaces. The loss of basic properties will lead to foaming of the working substance, which will ultimately cause scuffing of the main gear. As a result, the gears of the transmission differential will begin to hum, that is, the operation of the gearbox will be accompanied by a hum.

After 500-1000 km, the teeth on the gears will be destroyed. And this will lead to the transmission jamming. The driver will not be able to engage one or more gears. In Nexias with automatic transmissions, oil is also used to cool the unit. Failure to change the lubricant in a timely manner will result in kicks and jolts when shifting gears.

How to check the oil in a Daewoo Nexia box

The oil level in the Daewoo Nexia gearbox may change during operation; to maintain system functionality, it must be between the maximum and minimum marks. Another point is that over time, not only the volume evaporates, but also the additives, on which the performance characteristics of the mixture depend. As a result, the lubricant becomes unsuitable for use and does not fully solve current problems.

After 1 thousand kilometers, the gear teeth will be destroyed in the absence of normal lubrication, and the transmission may jam. The driver will not be able to engage some gears or all at once. In automatic transmissions, the oil is responsible for cooling the unit; if it is not replaced in a timely manner, shocks and kicks will appear when changing gears.

Before changing the old one, you need to test the fluid level in the system - this will allow you to understand whether it is normal or not. When there is a critical shortage of technical fluid, carefully inspect the unit and check for leaks. A visual inspection of the transmission allows you to assess its condition. There should be no cracks or stains from leaks; if they are present, measures must be taken.

You need to constantly test the lubricant level; an alarming symptom is the appearance of drips

1. Raise the front left of the car on a jack. The control hole is located in an inconvenient place; you can try to access it from under the hood, but this will be more difficult.
2. Turn the left wheel (watch as the vehicle moves) using a cylinder wrench.
3. After completing the dismantling, look at the plug-bolt near the CV joint. Unscrew it using a key.
4. If the lubricant content is in order, after twisting the plug, liquid will appear near the lower hole.

Maintenance is done at specified intervals; if the time has not yet come, the lubricant is clean, but there is not enough of it, you can top it up. When foreign impurities or inclusions are present, a complete change is required, including draining the waste and flushing the system. A strong change in the color of old oil, the appearance of foreign odors, or the presence of impurities that should not be present indicate the need for maintenance.

Level control and topping up

Before changing the lubricant, you need to make sure that its level is normal. If the check shows a critical lack of fluid, you need to carefully inspect the unit for leaks. Visually assess the condition of the transmission - the gearbox should not have cracks or other signs of leaks. Otherwise, the problem must be solved.

Visually familiarize yourself with the process of replacing transmission fluid in a Daewoo Nexia car in the video (author - Alexandr Borziy).

To diagnose the oil level, do the following:

Tools

In order to replace the fluid in the gearbox of a Daewoo Nexia, you will need the following tools and accessories:

• jack;
• syringe;
• 13 mm socket head;
• 17 mm socket head;
• 19 mm wrench;
• oil directly;
• transmission pan gasket;
• container for draining used lubricant.

In order to choose the right gasket, it is first recommended to inspect the transmission pan from below. This is due to the fact that there are two types of pallets, having 10 or 11 holes - the number of holes must be checked before purchasing a gasket. In addition, you don’t have to buy a gasket, but remove the pan and cut it out yourself from paronite, or simply replace it with a sealant, which in practice copes well with the task.

How to change the lubricant yourself?

You can replace the working fluid with the help of specialists at a service station or yourself. Let's look at the process of changing it yourself.

Preparation

Before completing a task, you need to prepare. Buy two liters of lubricant and prepare the tools:

Before purchasing a gasket, be sure to inspect the pan on the transmission. On sale you can find two types of pallet gaskets, which are mounted with 10 or 11 bolts. Therefore, when buying a seal, make sure that it suits you. If it is not possible to purchase a gasket, you can make it yourself from paronite. As a last resort, if there is no seal, the perimeter of the pan must be coated with sealant.

Detailed instructions for changing the oil are given in the video (the material was filmed and published by the Expert R channel).

Stages of work

The replacement procedure must be performed in a garage with a pit or on an overpass:

Price issue

When performing work yourself, there is no need to spend money on service stations. You just need to buy lubricant. The cost of gear oil depends on the manufacturer. For example, one liter of universal “Mannol 80W-90” costs the buyer 212 rubles on average. Castrol 80W-90 lubricant costs about 350 rubles per liter canister. The cost of original Toyota oil of the same volume is about 730 rubles.

See photos of replacing transmission fluid yourself in our gallery.

How to drain oil from a Daewoo Nexia box

Changing the oil in a Daewoo Nexia with 16 valves begins with draining the waste. Old lubricant does not perform current tasks at the proper level, so premature wear of working parts is likely. To extend the life of the vehicle, maintenance must be carried out in a timely manner.

Most car maintenance work can be done on your own, sometimes requiring wheel removal

To change the oil in a Daewoo Nexia manual transmission, you need to prepare a complete set of tools. It includes a jack, a set of wrenches, construction or medical syringes, a jack, a new gasket, and a container into which the old waste will flow. Gaskets can be mounted with 10 or 11 bolts; you need to immediately clarify which option is needed. If the required gasket is not commercially available, you can make it yourself from paronite. In the absence of a sealant, in principle, the pan is coated around the perimeter with sealant.

1. Warm up the engine, then turn off the engine and drive the vehicle to the work site.
2. Get under the car, remove the engine protective kit, if it is there, by tightening the fastening bolts.
3. Using a socket-type working head or a wrench, tighten the screws on the pallet structure - first at the front, then on the other parts. Place a container, preferably a basin, so that oil flows into it from the pan.

When the waste has drained, the pan is completely dismantled. The gasket may tear; it will be necessary to remove its remains in places of contact with the transmission operating unit. Typically, 1.5 liters of working fluid comes out of the pan, the rest of the volume will remain in the crankcase. To completely remove the grinding, jack up the front wheel on the left, preferably higher.

Start of maintenance - draining work that does not fully fulfill current tasks

Tool for changing gearbox oil

Replacement algorithm

The oil is changed when the engine is warm so that the waste is drained more completely. We install the car on the pit/overpass and begin work in this order:

Unscrew the plastic protection.

We turn out all the bolts of the pallet except the last two.

Drain the used oil.

Raise the front left wheel with a jack.

The control hole plug is unscrewed with the head at 13.

How to change the oil in a Daewoo Nexia gearbox yourself

If you are the owner of a Daewoo Nexia car, you may encounter a problem such as a lack of technical information regarding the frequency of oil changes in the Daewoo Nexia gearbox. Indeed, in the instructions, the manufacturer clearly indicates that the volume of transmission fluid will ensure correct operation of the gearbox throughout its entire operating life. Unfortunately, even if you try to re-read these lines several times, you still won’t find a word about when this operational period ends. We will try to help you in this matter by providing useful information to increase your knowledge regarding the operation of individual important components and mechanisms of your car.

Change of oil

Some motorists prefer to perform such manipulations almost immediately after purchasing a car, despite the extremely low mileage. They argue for their actions by the fact that oil could have been filled at the factory, accompanied by technical characteristics that do not suit the car owner. Indeed, the fact of such dissatisfaction and, to some extent, reinsurance is confirmed. At the factory, mineral oil is sometimes poured into the gearbox. This liquid is good in the summer. Unfortunately, in winter it becomes excessively thick, preventing the normal operation of the gearbox. It is for this reason that many people prefer to purchase synthetic or semi-synthetic oil.

Useful tips

If you have decided to replace the transmission fluid in the gearbox of your favorite car yourself, we recommend that you familiarize yourself with our useful tips. Initially, you need to check the oil level in the Daewoo Nexia gearbox. It doesn’t matter if you have absolutely no idea how to do this. We are ready to instruct you, eliminating the information gap. By the way, it is useful to carry out such a check after the car has once again covered 15 thousand kilometers. By checking how much oil is left in the Daewoo Nexia box, you can top up the missing amount in time and prevent gearbox failure.

Believe me, the gearbox can, of course, be repaired at service stations, however, such help will cost you too much.

So, to check the oil level in the Daewoo Nexia gearbox, you need to use a special dipstick, which you can easily find after lifting the hood.

This special dipstick has markings accompanied by the words “min” and “max”.

It is important that the trace of oil on the dipstick after removal from the hole is between these two marks. If you notice that it has dropped below the minimum mark, it means that there is an oil leak in the box. Be sure to add the missing amount and observe in the following days whether the loss continues or not by re-checking the oil level. If a lack of transmission fluid is again detected in the Daewoo Nexia gearbox, take steps to find the problem.

Replacement frequency

Understanding that driving on used material can cause serious damage to the gearbox, we recommend that you fill in new transmission fluid after one hundred thousand kilometers. Our recommendations are based entirely on statements made by professional service station technicians. Although there is a separate category of thrifty car owners who prefer to drain the used fluid after 60 thousand kilometers.

Well, you have the right to decide for yourself when it will be useful to replace the transmission fluid, but we recommend not delaying this process if the mileage has exceeded one hundred thousand. You should not save on purchasing consumables for your “iron horse”, since such savings can lead to even greater financial losses.

What oil to use

We have already drawn your attention to the fact that there are several options for transmission fluid, differing in their technical characteristics. In particular, when using mineral oil, the gearbox will function successfully, but only if there are no low temperatures. You won't be able to drive your car in winter if you use mineral oil; it will simply become too thick, with a high level of viscosity of the oil in the box. Accordingly, you will not be able to change speed normally.

Many motorists like 75W80 synthetic lubricant. We confirm that it is surprisingly good in cold winters, however, in the summer it can provoke the appearance of third-party noises and sounds, for this reason it is better for you to still opt for the Daewoo Nexia gearbox oil recommended by the manufacturer.

Tools for work

Don’t rush to take your car to a service station; you can handle such a task as changing the oil yourself. You just need to prepare for such manipulation first. In particular, it is important to collect all the necessary tools so that no difficulties arise during the execution process. Every motorist can assemble the tools, since the list consists of those devices that are always at hand. So, you need to prepare:

Don't rush to buy a gasket at random, as you may later be disappointed and upset about wasted money. The gasket may be accompanied by ten or eleven holes.

Take the time to look under the box and count the number of holes. If you follow this recommendation, you will be able to purchase the correct transmission gasket. By the way, if the process of purchasing a gasket is accompanied by difficulties, then you can make it yourself by cutting it out of paronite. You can also use a sealant without purchasing a gasket.

What kind of oil to fill in the Daewoo Nexia gearbox ~ VESKO-TRANS.RU

Daewoo Nexia is one of the most common cars on the roads of the Russian Federation.

It gained such popularity due to its low cost, maintainability and good level of comfort for its price tag. You can also add to this list the low price of spare parts and ease of maintenance.

All these reasons will allow you to look after your own car without much difficulty and do regular maintenance without the help of others.

In this article we will carefully tell you how to change the lubricant in the gearbox of the Daewoo Nexia, what kind of fluid is best to fill in and how much of it will be needed.

Many people are interested in the following question: what kind of oil is better to fill and how much in the box of the Daewoo Nexia. By volume you will need about 2 liters. water, as far as the manufacturer is concerned, we advise obtaining only high quality, time-tested lubricants such as Hessol. Such a product will help the mechanism feel comfortable under all road and weather conditions.

As for the labeling of fluids, the manufacturer advises filling a manual transmission with fluid with the license plate SAE 80W GL-4. This composition is intended for cars used in good weather conditions. If you are a resident of the north or use your car in places with low temperatures, use a product labeled 75W-90 GL-4.

A logical question arises, what kind of oil to fill in the Daewoo Nexia gearbox? The plant allows the use of both synthetic and mineral waters. Here the choice is only yours.

• The first variation is more expensive, but has excellent lubricating functions and is of higher quality.
• The 2nd is an economical option, which is not recommended for use in extreme conditions, including weather conditions.
• For proper and comfortable operation of the gearbox, we recommend using synthetic or semi-synthetic oils for Daewoo Nexia with the following markings:

Read also: How much oil do you need to change in an engine?

Any of these types must meet the requirements of the GL-4 standard.

As for how much oil to pour into the box of the Daewoo Nexia, you should purchase a 2-liter bottle. This should be enough to correctly change the transmission water.

When choosing the compositions of the proposed markings, we recommend paying attention to the Hessol brand.

This brand has special protection against counterfeit products - the original name of the product is engraved on the bottle.

German manufacturers do not use recycled materials for their production, so they not only do not leave sediment during the entire period of use, but also clean the mechanism of accumulated plaque.

Changing water in an automatic transmission is a fairly simple process if you choose the right consistency and consumables and prepare in advance. The function should be performed after 7-8 years of car operation, or after 100-120 thousand kilometers. A timely oil change in the Daewoo Nexia gearbox will help you avoid costly repairs of the unit.

Let’s first figure out what devices and tools will be useful.

1. Syringe or pump.
2. Jack.
3. Canister of lubricant.
4. Size 19 wrench.
5. Pan gasket.
6. Socket heads of 13th and 17th sizes.
7. Containers for used transmission components.

Before purchasing a gasket for a manual transmission, carefully inspect the pan. To do this, you will need to get under the car and look at the bottom. To make the process easier, use a hole in the garage or an overpass, which can be found in virtually every town. After you have climbed under the vehicle, look around and determine what type of pallet you have.