Characteristics of the Starline Twage A4 car alarm and operating instructions

03/02/2022 1,815 Alarms

Author: Victor

The Starline A4 car alarm is an anti-theft system with two-way communication, which incorporates a modular principle for constructing a vehicle security system. Despite the fact that this model is powered by a voltage in the range of 9-18 volts, its installation is allowed only on passenger cars.

[Hide]

Specifications

The Starline Twage A4 car alarm model has the following characteristics:

• packet data transfer between the communicator and the microprocessor device is performed with dynamic signal encoding, which protects it from interception;
• the signal control pulse frequency is 433.92 MHz;
• the operating range of the main communicator is 1200 meters in open areas without impulse interference in the mode of receiving signals from a microprocessor device;
• in signal transmission mode, the range of action of the main remote control is 600 meters;
• the operating range of the spare communicator, which is not equipped with a screen and two-way communication option, is 15 meters;
• car alarm Starline Twage performs its functions in a wide temperature range, ranging from -40 to +85 degrees;
• The signaling system is powered by direct current in the electrical network from 9 to 18 volts, which means installation of the complex is allowed not only on cars, but also on motorcycles;
• the amount of current consumed by the anti-theft complex when the protection mode is activated is 20 mA;
• at the output of the electrical circuit connecting the siren, the maximum possible current is 2 amperes;
• at the output of the power lines for connecting lighting devices, the current value is 7.5 amperes for each lamp;
• At the output of the electrical control circuits for the door lock drive, the current value is 15 amperes.

The range of the communicator is determined by the following parameters:

• location of installation of the antenna adapter in the car interior;
• the place where the car and the car owner are located when using a pager;
• presence of interference in the area;
• weather;
• battery charge;
• battery charge in the communicator.

Malfunctions A4

Starline A4 car alarm breakdowns

Equipment

System Kit
The Twage A4 model kit includes the following components:

• one main communicator equipped with an LCD display and a feedback option; its range is higher than that of an additional device;
• a spare communicator, has a shorter range, is not equipped with a screen and a two-way communication option;
• microprocessor device;
• two-level sensitivity controller;
• antenna adapter;
• light indicator for determining the state of the signaling;
• technical manual that allows you to correctly connect and launch the security system after installation;
• Valet service key, used to adjust basic parameters and enter emergency mode;
• limit switch for mounting on the hood;
• special 30 amp relay with socket;
• installation wires for connection;
• User's note.

Car security system with two-way communication Twage…

Twage, A4, a2, a1

• Image
• Text

Car security system

with two-way communication

Twage

— A4, A2, A1

I N S T R U C T I O N

P O E C S P L U A T I O N S I U S T A N O V K E

Key Features

Areas protected by the anti-theft complex:

• the power unit is protected from starting by installing an electrical blocking relay;
• door locks, trunk lid and hood are protected by limit switches, there is one switch, the rest must be purchased additionally;
• the machine body is protected from shocks and movements by means of a sensitivity controller;
• an additional controller is used to protect the interior;
• ignition protection is provided by a special input against switching on;
• The handbrake lever is protected from being disconnected.

Azis 8800 tas*tv demonstrated the operation of Starline A4 at a distance from the car.

The security of the anti-theft complex is ensured by:

• limited number of alarm cycles;
• interruption of alarm impulses without deactivating the protective mode;
• storing in memory the initial state of the anti-theft complex when the battery is disconnected;
• personal emergency deactivation password.

Signal protection options:

• nine security zones independent from each other;
• light and sound alarm impulses are activated when security controllers are activated;
• transmission of warning pulses about the triggering of alarm signals to a communicator with two-way communication;
• machine engine blocker mode;
• two activation modes for the anti-robbery option;
• panic mode, which ensures activation of alarm sound and light signals when suspicious people appear near the machine, is activated by the user.

Among the capabilities of the Starline Twage signaling system we include the option of self-diagnosis and mode indication:

• checking the status and activated operating modes is provided by diode lamps installed in the cabin and on the communicator with two-way communication;
• The alarm performs diagnostics of all security controllers, turning off failed devices and warning the car owner about this;
• the activation of the siren can be indicated by light and sound signals;
• diode indication of non-working switches installed on door locks, hood and trunk.

Antony Gorodetsky spoke about the features of the Starline A4 signaling system on a scooter.

Separately, we should highlight the service options of Starline A4:

• the ability to activate and disable protective mode without using a communicator;
• the ability to configure a protective function with a delay in turning on the controllers;
• it is allowed to turn on the protection mode when the engine is running;
• if necessary, the consumer can turn on the security without activating the built-in shock controller;
• The consumer can control the door locks using the main key or by pressing the brake pedal;
• two-stage opening of door locks;
• the Comfort option will ensure automatic closing of the power windows and sunroof when the protection mode is activated;
• the ability to remotely activate and deactivate the Valet service mode;
• two channels can be used to control additional equipment and devices installed in the machine;
• option for polite illumination of lighting in the car interior;
• there is an option to search for a car in the parking lot; when it is turned on, the car’s lights will blink several times to show the car owner where it is parked;
• the user can remotely configure and adjust the parameters of the sensitivity controller;
• remotely, the consumer can link new and delete old communicators from the memory of the microprocessor unit;
• the microprocessor module controls the number of pagers stored in memory;
• the car owner can independently reset all configured options to factory settings;
• with the additional installation of the Starline module, the consumer can implement remote start of the power unit;
• the microprocessor unit is equipped with an interface for additional connection of a GPS module, with which you can determine the coordinates of the car in case of theft;
• the communicator has an option to lock the keys, which will prevent them from being accidentally pressed in your pocket;
• communicators with two-way communication have an energy saving option, this provides an increased battery life;
• the communicator with two-way communication has the option of monitoring the battery charge, with its help the consumer will promptly learn about the low battery;
• The main communicator is equipped with a backlit screen.

The azis 8800 tas*tv channel demonstrated the operation of the Starline A4 anti-theft complex.

disabling security mode without a key fob...

Page 7

• Image
• Text

7

Twage A4, A2, A1

Service functions

· Switching on/off the security mode without a key fob · Automatic (passive) switching on the security mode · Automatic return to the security mode in case of accidental shutdown · Silent switching on/off the security mode · Switching on the security mode with a delay in activation of door, hood, sensors

trunk · Security mode with the engine running · Security mode with the built-in shock sensor turned off · Possibility of multiple remote protection within 1 cycle

disabling/enabling the shock sensor and additional sensor by level · Remote control of door locks · Control of door locks from the ignition key · Control of door locks by pressing the foot brake pedal · Two-step unlocking of door locks · Two-pulse unlocking of door locks · Possibility of implementing the "comfort" function · Remote turning on/off the Valet service mode · 2 channels for controlling additional vehicle devices · Courteous car interior lighting mode · Car search mode · Remote configuration mode for the built-in shock sensor · Remote programming mode for new and erasing old key fobs · Control of the number of key fobs in the alarm memory · Possibility of online operation resetting programmable functions to factory settings

presets Remote engine start/stop when working with a launch module

StarLine · Engine start mode by timer when working with the StarLine launch module · Special interface for connecting the security search GSM / GPS module · Mode for blocking the operation of key fob buttons · Key fob energy saving mode with feedback · Control of the key fob battery discharge with LCD (in the A4 model) · Fluorescent illumination of the key fob display with LCD (in the A4 model)

Advantages and disadvantages

Advantages of the model:

1. Conversational encoding of packet data. According to the manufacturer, it is impossible to hack the alarm by intercepting the signal with a scanner.
2. Low price. This signaling model has already been discontinued, but can still be found on sale. The cost of the anti-theft system is about two thousand rubles.
3. Full functionality for car protection. The Starline A4 alarm system does not have many additional options that other anti-theft systems can boast of. But the functionality it is endowed with is sufficient to protect the machine.
4. Easy to install. An inexperienced car owner will be able to independently install the anti-theft system by carefully studying the operating and installation instructions. It clearly describes all the nuances of installation and connection.

Another advantage of the Twage A4 is the ability to connect additional modules. If you install a GPS device and an autostart unit, the alarm will become a full-fledged security system. The manufacturer recommends using only original Starline devices as additional modules.

Flaws:

1. Keychain. The communicator can be called a “disease” for many Starline models. Over time, the device begins to malfunction. This may be due to the battery being discharged, but sometimes the reason is the wear and tear of the communicator. You can solve the problem by flashing the device.
2. Difficulties in initially setting up the system, especially if the signaling system is additionally equipped with an autostart module.
3. Poor technical support work. The manufacturer assures that the consumer will be able to contact company representatives at any time to clarify questions regarding installation and maintenance. In fact, it is almost impossible to get through to technical support. The work of specialists is rated 2 out of 5 by most users.

Video

User Alexander Shkurevskikh showed the process of repairing the Starline A4 communicator, in particular, replacing its display.

Do you have any questions? Specialists and readers of the AUTODVIG website will help you ask a question

Was this article helpful?

Thank you for your opinion!

The article was useful. Please share the information with your friends.

Yes (100.00%)

No

X

Please write what is wrong and leave recommendations on the article

Cancel reply

Rate this article: ( 3 votes, average: 5.00 out of 5)

Discuss the article:

How to install?

Alarm connection diagram
During installation, it is important to choose the correct location for installing the devices:

1. The microprocessor unit is mounted inside the car; it must be installed so that the criminal does not find the device during a break-in. It is best to mount the unit under or behind the control panel if there is free space behind the center console. The module must be placed in such a way as to prevent drops from flowing down the electrical circuits into the housing. Fixation is done with bolts or tape. The device should be securely fastened to prevent vibration during movement.
2. The antenna adapter is attached to the inner surface of the windshield. During installation, it must be taken into account that the transceiver must be placed no closer than 5 cm from the metal components of the machine body. This will prevent interference.
3. A siren is installed under the hood of the car. It must be placed away from the cylinder block. The device is mounted with the horn facing down, this will prevent moisture from accumulating inside. When installing, make sure that a potential criminal will not have access to the siren and its electrical circuits from the bottom.
4. The LED indicator can be fixed next to the antenna. Its installation is allowed in any visible place in the cabin, for example, on the instrument panel.
5. The shock sensor is fixed on the metal surface of the body inside the car. It is advisable to install it in the center of the body. For installation, you can use a partition separating the engine compartment and the interior. The controller is fixed with tape or self-tapping screws. All additional sensors are installed in accordance with the technical manual.
6. The key to enter the Valet service mode is mounted in a hidden place. But it must be installed so that the consumer has access to the button when he is in the driver's seat. This is important for setting up and emergency shutdown of the alarm in case of loss of the communicator. You can disguise the key by installing it under the dashboard and wrapping it with electrical tape.
7. A limit switch is mounted on the hood. If you additionally purchased limit switches for all doors and trunk, then to install them you will have to remove the plastic lining. When installing, please note that the gap between the contact elements when the door or luggage compartment is locked should be no more than 3 mm. If this nuance is not taken into account, false alarms are possible.
8. After installation of all components, the electrical lines are laid. Wires should be located away from sources of interference. We are talking about high-voltage cables, ignition coils, and electronic devices. Electrical circuits must not come into contact with moving parts of the body. All wires are connected with the battery disconnected in accordance with the diagram. If the connections are permanent, then they are connected by soldering; the connecting points must be wrapped with electrical tape.
9. If you decide to additionally install an autorun module, then it must be connected correctly. The three-pin connector of the device is connected to the four-pin plug on the microprocessor unit. This output is hidden by a hinged cover on the device body. To connect, use the cable that is included with the autostart module.

You will learn about mistakes that should not be made when installing the complex from the Avtozvuk video.

How to use the signal?

Using all functions of Starline Twage A4 is possible only after linking the communicator.

Programming a new key fob:

1. Enable or disable the alarm protection mode. There is no need to install the key in the lock; with the ignition off, the consumer needs to click on the service button seven times.
2. Activate the ignition by turning the key in the lock. The siren speaker will play seven signals, and the alarm LED will blink the same number of times. The system has entered binding mode.
3. Click on the first and second keys and hold down these buttons, which will bind the first communicator. If programming is successful, the siren will play one beep. Exit from the programming mode will be indicated by five flashes of light devices. This will happen if more than ten seconds have passed since the last pager entry.
4. The previous paragraph is repeated for each programmable communicator. After linking the pagers, the alarm will play sound and light pulses.
5. After completing the binding procedure, turn off the ignition. The lights will blink five times.

Setting up autorun

You can set up automatic start only after installing the additional Starline 02 module. The device is installed on cars with manual and automatic transmissions, regardless of the engine type - gasoline or diesel. The consumer can program the start parameters of the power unit by time or timer.

Features of autorun settings:

1. The power unit is started remotely and stopped by successive clicks on the first button. The button must first be pressed quickly and then held down for a few seconds. The car engine will start if the car has been prepared.
2. To activate the timer function, use keys numbered 1 and 2. They are clicked sequentially. That is, the first button is pressed quickly, and the second is pressed for a few seconds. The display of the communicator will show the time after which the engine will start.
3. Activating the turbo timer option for one, three or six minutes will ensure support for the operation of the internal combustion engine in the absence of the ignition key in the lock. This option starts automatically when the key is removed from the lock, but to implement it, you must configure the first function of the module in advance.

Designation of buttons and symbols on the key fob

The designation of the Starline A4 key fob buttons is shown in the photo below.

Keychain alarm

Key fob button designation

Designation of indicators on the communicator display:

• A – the Valet service function is activated;
• B – the option to bypass the sensitivity controller is activated;
• C – the anti-theft complex is configured to start the internal combustion engine according to a timer;
• D – passive activation mode of the protective function is activated;
• E – engine blocker mode is activated.

Diagram of the communicator screen with symbols Designation
of icons on the screen:

1. The second level of the sensitivity controller has been activated. This indicator lights up when the optional controller is turned on.
2. The option to bypass the additional controller is activated.
3. Indicator indicating that the tailgate is open.
4. This symbol indicates that the brake pedal has been pressed or the handbrake lever has been released.
5. The vehicle's power unit is started.
6. One of the doors in the car is open.
7. The hood of the car is open.
8. The key is in the lock and the ignition is activated.
9. Valet service option included.
10. The anti-robbery option is activated. Enabling it will allow you to block the power unit in the event of a violent seizure of the car.
11. Key lock has been activated on the main communicator.
12. The battery installed in the key fob is dead.
13. Acoustic signals are activated and sound to confirm functions.
14. Audible confirmation signals are turned off.
15. The first level of the sensitivity controller has been activated. This indicator indicates that additional controllers are activated if they are installed in the machine.
16. The car door locks are open.
17. The car door locks are locked.
18. The communicator receiver is activated.
19. The option to bypass the built-in sensitivity controller is activated.

Factory reset

To reset all programmed functions, do the following:

1. Turn off the ignition in the car by turning the key to the Off position. Find the Valet service key and click on it nine times.
2. Turn the lock key to the ACC position. The siren speaker should produce nine beeps. This indicates that the anti-theft complex has entered the reset menu to factory settings.
3. The service key is clicked one more time. The siren will play one signal.
4. Click on the first key of the communicator. The device will emit a melodic pulse, this indicates a successful reset to factory settings.
5. Ten seconds after the reset, the alarm will automatically exit the programming menu. You can leave the mode by turning off the ignition. The lights will blink five times. The communicator will emit one melodic pulse.

Compatibility of the A4 key fob with other StarLine models

The Starline A4 signaling control panel with or without feedback is compatible with communicators from the Starline A2 model. The key fob is also compatible with the Starline 24 V alarm system, but in this case we mean only spare communicators without a display and feedback. Pagers from Starline A2 and Starline 24 V can be used to control the A4 model.