DIY armrest for viburnum, drawings - all about Lada VAZ cars

Armrest models

At the moment, many armrests are offered in car accessory stores, but not all of them can be installed in the Lada Kalina. Or rather, installing an armrest is possible, but problems may arise with adjusting the seats or fixing the seat belt, for example.

Another important point: Kalina armrests often do not fit Kalina 2.

Alamar is a very popular armrest that is used for installation on the Lada Kalina. It's relatively inexpensive. At the same time, it does not block access to the handbrake, seat belt latches and does not create obstacles for adjusting the seats. It can be moved horizontally, which is very convenient in some cases. Unfortunately, the armrest that was installed on Kalina cannot be installed on Kalina 2 without modifications. If you want to install it on Kalina 2 yourself, you should do the following:

cut off the pin, since there are no holes for it on the seats of Kalina 2;
bend the leg of the armrest so that there is no tilt towards the passenger;
Place an additional washer on the fastening bolt, since the hole in Kalina 2 is deeper. Otherwise, when fixed, the armrest will begin to sag and tilt towards the passenger seat.

But at the moment there are already armrests installed on the Lada Kalina 2. Their article numbers on the official Alamar website are 54.1 - 54.4, 54.11 - 54.13. Price on the website is 750 rubles. and model 54.13 - 1300 rubles.

Armster. In terms of functionality, there are no problems. Can slide or tilt back. There are no complications in using the belt, handbrake or adjusting the seats. Attached to the floor, on the base of the chair. The only thing is that in some cases it happens that you need to modify the fastening, drill holes 3-4 mm or take an adapter. Models that fit Lada Kalina: Armster-1 and Armster-S. To be precise, in accordance with the guarantees stated by Armster, these armrests are intended for the Lada Kalina 05, but according to knowledgeable people, these armrests are suitable for any Kalina. Including, Lada Kalina 2 can be equipped with such an armrest. Armster refers to model armrests. Good but expensive materials were used there. Therefore, its price is not small, about 5-6 thousand rubles.

It should be noted that there are many cheaper analogues. For example, FedorAuto or Chinese options. Structurally, they are exactly the same, but cost much less. Perhaps because of the quality of the materials, or maybe simply because the brand is not promoted. After all, consumers often pay a lot of money not for quality, but for the name and advertising on TV.

Azard. This company has both a model and a universal range. But the model range is designed only for old Ladas. However, there are also universal models that can be installed on Kalina. The price range is low - about 700 rubles. There are some minor difficulties in accessing the seat belt latches, but you can get used to them.

Rex,Torino. Universal armrests. They attach without problems to the base of the seats on almost any Lada. The price is small. A minor drawback can be considered complications in using the handbrake and seat belt latch. These functionalities do not overlap, but access to them is a little difficult. It will take some getting used to.

In addition, there are many Chinese station wagons that can be installed without much difficulty and their price will be around 300 rubles. So even the smallest budget can handle installing an armrest. Of course, for 300 rubles. it will not look like it did for 6,000 rubles. but in terms of convenience it can quite fulfill its task.

Some inconveniences in terms of access to the handbrake or seat belt latches can be tolerated and adapted to them. And the fact that it will be problematic to adjust the chairs is generally a trifle. As a rule, the driver adjusts the seat once and does not touch the adjustment again for years. Unless it is, in the full sense, a family car, where relatives take turns using the car, and everyone reconfigures the driver’s seat to suit themselves.

Universal option

A universal armrest, suitable for cars Lada Kalina, Forza, Granta, etc., is also manufactured by TORINO. There are other names, but they are usually fake.

REX product

This element is attached to the floor and bolted to the front seats. Installation takes literally 2-3 minutes. Once the armrest is in place, you will receive:

Right hand rest;
Cup holder;
Two small drawers for storing things.

The price of such pleasure for the driver of a Lada Kalina car is quite small - only about 600 rubles. But, despite all its positive qualities, the part will also have several disadvantages. Firstly, using the handbrake will be a problem for the driver, and he will be forced to fold back the armrest in order to put the car on the handbrake. And secondly, the seat belt fasteners will be pressed closely to this element, which will undoubtedly cause inconvenience.

Speaking of Chinese manufacturers, the first place in the production of this element for the Lada Kalina car is occupied by. The difference between its products and the original is that the fake does not have a cup holder. Otherwise, everything remains the same, even the price.

The quality of the fake is quite good, but, in addition to the above-mentioned disadvantages, it has another big drawback - the fasteners do not fit the standard ones, and they have to be redone.

Do you need an armrest in a car?

Some models of cars in the budget segment are sold without a special elbow rest. Drivers quickly get used to it and don’t even notice that their car is missing something. Therefore, a logical question arises: is there any benefit at all from the armrest?

In fact, there is, and it is quite noticeable. The armrest significantly reduces the strain on the arm and back muscles during frequent use of the gear lever. This is especially true in cars with a manual gearbox. When traveling long distances and even in regular traffic jams, the hand becomes tense and tired, in some cases the muscles begin to cramp, which can lead to an accident.

the armrest in the car significantly reduces the load on the muscles of the arm and back

Another nice feature is the ability to use the armrest as a place to store useful little things. A water bottle, wallet, car documents, sunglasses case and more can be placed inside and will always be at your fingertips (literally and figuratively). Expensive models often have armrests equipped with control buttons for some vehicle devices.

In addition, an ordinary armrest can create an atmosphere of home comfort in a car and make your stay in it more comfortable.

AndRCZ

www.drive2.ru

Let's sum it up

We found out that the armrest on the Lada Kalina allows the driver to feel comfortable while traveling for a long time. This useful accessory, the installation of which can be done by hand, can not only fit harmoniously into the interior, but also become a practical box for the most necessary luggage (keys, phone, etc.). There is a lot of useful information on how to install the armrest.

general characteristics

classifies Lada Kalina as a subcompact model. These cars performed excellently in urban conditions. For optimal operation, the range of external temperatures ranges from minus 40 to plus 45 degrees (Celsius). Also, to ensure that this vehicle exhibits its optimal characteristics, it must be used on paved roads.

Most Lada Kalinas are equipped with 8-valve engines. There are also versions with engines whose heads are equipped with 16-valve designs. Such motors are marked as “11194” and “11184”. Both versions of the power unit are located in the engine compartment according to a transverse arrangement. The power plants are equipped with modern distributed fuel injection systems.

The exhaust manifolds of these models have exhaust gas catalysts, which is done for the sake of the environment.

As a modern option, you can consider remote control of the central door lock and window drives. Also, as an option, a locking unit for the luggage compartment lock can be installed.

If there is a need to activate or deactivate the security system, then such an action is available in any situation. This mechanism allows you to lock all doors at once. This useful feature allows you to quickly lock yourself in your car, for example, while hiding from being chased.

Tips for choosing elbow supports

The only problem will be the color of the armrest. The fact is that for the covers installed in the cabin, it is necessary to select a part to support the hands of a certain color. This is not always possible. Sports seats require a black armrest for Kalina. Of course, you can order covers to match its color, but this will cause additional costs.

After installing the armrest for Kalina, at first it is not entirely clear what the convenience and charm of such a car accessory is. It seems to the driver that he is very far away and inconvenient. You just need to move the seat and everything will fall into place. Now, even when changing gears, you can rest your elbow on the armrest. Moreover, the passenger will not even notice it. The design of such an armrest is very simple; there are no unnecessary compartments.

If it gets in the way, it can be easily thrown back. This model does not interfere with the use of the parking brake lever. It is very easy to fasten the seat belts. Many drivers believe that with an armrest, the interior becomes more comfortable and beautiful. The modern armrest for Lada Kalina, equipped with a black adapter, differs from the previous ones in a number of positive qualities:

You can adjust the angle of inclination and adjust the height;
the lid has the ability to move forward;
it can rise by 105 mm;
it has a spacious volume;
The armrest is equipped with a holder.

What is the first thing you pay attention to when purchasing a new car? Technical characteristics, engine power, gas tank volume and fuel consumption? Or maybe the appearance of bumpers, spoilers, headlight shape or body color? No matter how beautiful your car looks from the outside, you will spend most of your time in its interior. So taking care of the car’s interior is not a whim, but a completely necessary condition when buying a new iron horse

And if everything is more or less clear with the seat upholstery and the thickness of the steering wheel, then what about such a mysterious element as the armrest? Is he needed or not? And if you still need it, then how to make it and install it in a car that initially does not have an armrest in the basic configuration? Is it possible to create everything with your own hands or is it better not to suffer and order the work from a master?

Let's sum it up

Several years ago, a new product from AvtoVAZ appeared on the roads of our country - the Lada Kalina. However, they simply forgot to put an armrest on Kalina. So car enthusiasts have to install the part themselves.

Armrests for VAZ Lada Kalina Cross 2014-present

Armrests for VAZ Lada Kalina Cross 2014-present at low prices in Moscow. Large selection for all cars, delivery.

An armrest is an indispensable car accessory that provides additional comfort in the car interior. For the manufacture of car armrests for VAZ Lada Kalina Cross 2014-present. Only high-quality and reliable materials are used, impact-resistant and completely safe to use.

Advantages of car armrests for VAZ Lada Kalina Cross 2014-present

- high strength and wear resistance. The armrests are made of impact-resistant and high-quality materials that retain their appearance and do not deform for a long time;

- practicality and functionality. Not only do they provide convenience for the driver, but they can also serve as storage for small items that simply don’t have room in the glove compartment;

- external attractiveness. Wide adjustable armrests are traditionally installed on cars in luxury trim levels, and in the VAZ Lada Kalina Cross 2014-present. will look as organic and elegant as possible.

— provide free access to the handbrake;

— thanks to the reliable and super-strong fastening, they do not creak or become loose;

— ideal for the interior of your car;

- are durable and quick to install.

Various design options for car armrests allow you to choose the ideal solution for the interior of your car.

How to choose armrests for VAZ Lada Kalina Cross

To buy an armrest that meets all your requirements, answer a few questions:

What design option do you prefer for the top cover (leather, fabric, wood) and its color?

Do you need to adjust the armrest height, tilt or length?

What width of the car armrest will be optimal and most comfortable for you?

Do you need a spacious compartment for storing items?

What are your requirements for the functionality of the product (built-in cup holder, control buttons for on-board car systems, additional 12V socket)?

AvtoVAZ decided not to install armrests on the Lada Kalina 2 and Lada Granta, even on the “luxury” configuration. For many, there are no questions about its absence, but the majority of car enthusiasts believe that there simply must be an armrest and install it with their own hands. We decided to find out which armrest for the Lada Grant and Lada Kalina 2 is the most comfortable, practical and inexpensive.

The second generation Lada Kalina consists only of a hatchback and a station wagon. The sedan is produced as the Lada Granta model. Apparently this is why both Lada models do not have an armrest..

Individual option

Individual armrests for the Lada Kalina and Kalina 2 were originally produced. The first samples were located too high, and instead of comfort, they caused more inconvenience.

Over time, the fastenings were redone, and the armrest dropped a few centimeters, and at the same time, it could be moved along with the seats. For ease of use of the hand brake, the element was made folding. Unlike its analogs and "TORINO", "Alamar" did not have a compartment for things, and was completely cast. Its price was literally 150 - 200 rubles higher than the price of universal armrests.

Additional information about the armrest of Lada Kalina

You can buy an armrest in Novosibirsk on the same day you order it, shipping to other cities is possible, in the same way, on the day you order it.

For a Lada Kalina armrest, the price on the Internet may vary significantly. This primarily depends on the quality, i.e. on the materials used and the production technology of the product. The cheaper option also performs its function, however, it is radically different in appearance.

Types of armrests:

Universal - Suitable for all cars, so it requires fastening with self-tapping screws. Typically made of plastic.
Armrest Lada Kalina original - The name speaks for itself. This is an original armrest made at the factory. However, when installed in a car, you will have to change the entire console between the seats.
Plastic with individual fastening for each car - This can be ordered, for example, from China, but it is completely plastic, so it creaks.
An armrest with a wooden frame and an individual seat for each car - Moreover, it does not require mounting in the car.

Where the Lada Kalina armrest is already used:

For example, we managed to buy an armrest in Abakan, Barnaul, Belgorod, Berdsk, Vladivostok, Volgograd, Vologda, Voronezh, Gelendzhik, Ekaterinburg, Ivanovo, Irkutsk, Kazan, Kaluga, Kemerovo, Kirov, Komsomolsk-on-Amur, Krasnodar, Krasnoyarsk, Kurgan, Magadan , Leninsk-Kuznetsky, Magnitogorsk, Moscow, Naberezhnye Chelny, Nizhnevartovsk, Nizhny Novgorod, Novokuznetsk, Novosibirsk, Omsk, Orenburg, Perm, Rostov-on-Don, Samara, St. Petersburg, Sochi, Surgut, Togliatti, Tomsk, Tyumen, Ufa , Khanty-Mansiysk, Khabarovsk, Chelyabinsk, Chita and Yakutsk.

How to make this part for your car with your own hands

First of all, select the material from which the body will be made, as well as the fabric for subsequent upholstery. Their thickness affects the dimensions of the future product. Next, you need to make all the necessary measurements, and only after that start constructing the drawing.

We will talk about the choice of fabric for covering a little later, but we will dwell on the material for the armrest itself in more detail.

Material selection

Wood-based material is best suited for the armrest body. It can be a chipboard, fiberboard or ordinary plywood. If the proposed design does not have curves, then your choice is unlimited. Otherwise, the only material that will suit you is plywood, since only it can be bent by holding it over steam for some time or soaking it in hot water.

To bend the plywood, soak it in a bath of hot water

Consider the thickness of the board: it should not be less than 0.8 cm or thicker than 1.5 cm. The ideal option, which will be strong enough but not particularly bulky, is plywood 1 cm thick. To cover the lid you will need ordinary foam rubber.

Don't forget to prepare the accompanying tools: meter tape, graph paper, and an electric jigsaw for cutting the board into parts.

Measurements for the future drawing

The manufacture of an armrest must begin by measuring the necessary parameters. To do this, arm yourself with a meter tape, a pen and a sheet of paper where you will write down all the data received.

Measure the distance between the front seats.
Holding the gear shift lever with your right (or left, depending on the location of the steering wheel) hand, determine the most comfortable height for the future armrest.
Measure the distance from the handbrake to the back of the seats.
To prevent the window sill from interfering with fastening your seat belts, measure the distance between their buckles.
If you plan to install the armrest in such a way that it will be partially located above the handbrake handle, then move it to the on position, and then measure the dimensions and height of the rise.
Measure the area where your product will be attached.

measure the distance between the seats to find out the size of the future armrest

Element design

Having made all the necessary measurements, begin drawing up a drawing of the future armrest. Be careful: even small errors can lead to your product not being installed in its place or interfering with the operation of other elements of the car.

When creating a project, draw a diagram of the armrest taking into account all sizes and proportions. For more accuracy, draw the part from both the side, front and back. Don't forget to label the lengths of the sides: it will be easier for you to transfer the markings to the material.
Make a drawing for the upper part of the armrest - the future cover.
Consider how to attach the lid: will it tilt or bend. Depending on this, determine the location of the grooves or other fasteners.
If the part is not strictly rectangular in shape, carefully work out the bends.
Determine in advance the lengths of the screws that will be used in the work. If their sizes differ in different parts of the product, indicate this on the diagram.
Decide how the armrest itself will be installed: using special fasteners or tightly fixed between the seats. If necessary, add grooves to the diagram at the bottom of the structure.

Manufacturing process

Making an armrest with your own hands is quite simple if you have at least some experience with a jigsaw. If you have correctly measured all the distances and made the correct drawing, then all you need to do is follow the diagram and our instructions exactly.

Cut out the pieces from graph paper. After use, do not put them away far, because they will still be useful when covering the body with material.
Attach them to the plywood and transfer the contours.
Using an electric jigsaw, cut out the necessary parts.
To create curves, for example on an armrest cover, soften the plywood over steam or hot water.
Fasten all the parts using self-tapping screws, according to the project. If necessary, you can use glue, but it alone will not be able to firmly hold the structural elements.
If desired, you can install partitions inside the armrest: you will have compartments of different sizes for storing useful little things.
Glue foam rubber onto the armrest cover, otherwise your hand will feel the hardness of the wood even through the upholstery material.

Some tips for choosing an armrest

In most cases, armrests can be easily installed with your own hands in 20-30 minutes. In some cases, it will take more time and a little experience in using the tool to bore or file something. In rare cases, if you really want to install a specific armrest, but it does not fit this car, you should consult with the experts at a car service center.

They are masters and masters to do the impossible. Often a good craftsman finds an original way to install a seemingly completely inappropriate armrest. And in very rare cases it will not be possible to establish. True, about a master with golden hands, you should remember that his work will cost like gold. An armrest is not an essential item, but only an element of comfort.

You shouldn’t particularly insist that the armrest have a spacious drawer. There is no need to create 1 more glove compartment. After all, the car has plenty of pockets for small trinkets. It will be much more useful if the armrest has the ability to move back or recline.

back Interesting: Kalina or Priora, which is better?

Next Which fog lights can be installed on Kalina 2

Tags: choice, armrest, installation

Individual option

Individual armrests for the Lada Kalina and Kalina 2 were originally produced. The first samples were located too high, and instead of comfort, they caused more inconvenience.

Armrest models

Another important point: Kalina armrests often do not fit Kalina 2.

Unfortunately, the armrest that was installed on Kalina cannot be installed on Kalina 2 without modifications. If you want to install it on Kalina 2 yourself, you should do the following:

cut off the pin, since there are no holes for it on the seats of Kalina 2;
bend the leg of the armrest so that there is no tilt towards the passenger;
Place an additional washer on the fastening bolt, since the hole in Kalina 2 is deeper. Otherwise, when fixed, the armrest will begin to sag and tilt towards the passenger seat.

But at the moment there are already armrests installed on the Lada Kalina 2. Their article numbers on the official Alamar website are 54.1 - 54.4, 54.11 - 54.13. The price on the website is 750 rubles, and the model 54.13 is 1300 rubles.

Models that fit Lada Kalina: Armster-1 and Armster-S. To be precise, in accordance with the guarantees stated by Armster, these armrests are intended for the Lada Kalina 05, but according to knowledgeable people, these armrests are suitable for any Kalina. Including, Lada Kalina 2 can be equipped with such an armrest. Armster refers to model armrests. Good but expensive materials were used there. Therefore, its price is not small, about 5-6 thousand rubles.

Rex, Torino. Universal armrests. They attach without problems to the base of the seats on almost any Lada. The price is small. A minor drawback can be considered complications in using the handbrake and seat belt latch. These functionalities do not overlap, but access to them is a little difficult. It will take some getting used to.

In addition, there are many Chinese station wagons that can be installed without much difficulty and their price will be around 300 rubles. So even the smallest budget can handle installing an armrest. Of course, for 300 rubles. it will not look the same as it did for 6,000 rubles, but it may well fulfill its purpose in terms of convenience.

Universal option

A universal armrest, suitable for cars Lada Kalina, Forza, Granta, etc., is also manufactured by TORINO. There are other names, but they are usually fake.

REX product

This element is attached to the floor and bolted to the front seats. Installation takes literally 2-3 minutes. Once the armrest is in place, you will receive:

Right hand rest;
Cup holder;
Two small drawers for storing things.

The quality of the fake is quite good, but, in addition to the above-mentioned disadvantages, it has another big drawback - the fasteners do not fit the standard ones, and they have to be redone.

At what engine speed should you shift gears on the Lada Kalina?

I shift in all gears around 2400-2700 rpm. On Kalinka at low revs the traction is excellent, at 5th it can handle any climb at full load, at average speed (95-100 km/h)

popular wisdom: The cooler the jeep, the further you go behind the tractor

__________________ A weight is not a sparrow, if it flies out it will hurt (:

If you can’t go where you want, go where you can.

Agree. As a result of numerous measurements, the most economical mode was found. When braking with the engine I bring it up to 1500.

Added after 43 minutes

I would like to listen to an engine specialist and hear from him answers to some questions, for example: 1) What important processes in the engine begin to occur at speeds above 3000. 2) Is it possible to compare engines installed on old Lada cars and having MCM at 3400 rpm with engines ( four models) installed on Kalina 3) What does “The engines of front-wheel drive VAZs spin happily” mean?

And one more trivial question. Why should I, unless absolutely necessary (overtaking, heavy vehicle load), keep the engine speed above those at which it develops MKM. For engine 11183 is this, for example, 2500 rpm? Burn some fuel? Or to make him have fun? And one more. How can you compare, that is, equate completely different engines 1.6 8kl; 1.6 16kl; 1.4 16kl. having completely different characteristics? And finally. If you have a five-liter engine, will you really turn it like that?

Added after 9 minutes

Well, that is, I stood at idle for about twenty minutes and the engine started cranking.? Right?

Added after 1 minute

Well, here's a sober person. Gotcha!

Added after 13 minutes

Right. An experienced driver drives an automatic car. But still, while he gets used to his car, he looks at the instruments.

Added after 8 minutes

Nonsense of inexperienced drivers! With this driving method, consumption is higher. Proven in numerous experiments.

Added after 9 minutes

Keep the revs from 2000 to 3000. On average it will be 2500. Change gears within these limits.

Added after 2 minutes

1700 and almost to the cutoff, so whatever you say, “we’re riding on the moment”

Are you kidding me like that? The whole line? Or did he take vodka on his chest?

Source

Gear shift technique

Most cars use the following gear shifting technique. When starting, first gear is engaged and the car begins to move. Next, the engine spins up to 3000 rpm, the clutch is depressed, the gas pedal is released and second gear is engaged. All actions with the pedals must be done smoothly, but not too slowly. This is described in detail in the article “How to move off smoothly with a manual.”

Thus, the car picks up speed before engaging direct transmission. In order to change to a lower gear, for example to perform a maneuver, it is necessary to reduce the crankshaft speed to approximately 2000 rpm. Then the clutch is depressed, low gear is engaged and, increasing the engine speed to 2500-3000 rpm, the clutch is smoothly released. If the speed is not increased, then switching will lead to a sharp jolt of the car, and on poor surfaces it can even lead to a skid.

To determine the optimal speed for shifting gears on a particular vehicle, you can read the owner's manual. If there are no detailed instructions, then you can look at the value of the maximum torque and at what speed of rotation of the crankshaft it is achieved.

Based on this indicator, you can independently determine at what speed to change gears in a particular case. The moment of upshift can also be determined experimentally. But this method is more suitable for drivers with extensive driving experience.

Focusing on sensations

from an increase in vehicle traction, the value of the maximum torque can be determined. When passing through the point of maximum torque, a sharp decrease in engine thrust is felt, and the car accelerates less quickly.

Skillful driving means having the ability to quickly and at the right time change gears.

Dear readers! The article talks about typical ways to resolve legal issues, but each case is individual. If you want to find out how to solve your particular problem, contact a consultant:

+7 (St. Petersburg)

APPLICATIONS AND CALLS ARE ACCEPTED 24/7 and 7 days a week.

It's fast and!

In the absence of this, driving a vehicle will be significantly difficult. Therefore, before you start driving a vehicle, you will need to familiarize yourself with the gear shift algorithm.

This process varies on cars of different brands and models.

Moreover, it is important to carry out the switching process in accordance with certain rules

This significantly extends the period of uninterrupted operation of the engine, as well as the gearbox.

In turn, the inability to change speeds can cause a large number of different difficulties.

Features of the Cross modification

When considering the entire list of modifications of the LADA Kalina, one cannot ignore the outstanding VAZ project - the Cross version. This car is built on the basis of a station wagon, but has an impressive list of additions

Here the developers have placed significant emphasis on the ground clearance, which is an enviable 208 mm. The perimeter of the body is decorated with decorative linings, which simultaneously perform a protective function. On small off-road terrain the car behaves quite confidently. The developers did not forget to use enhanced protection for the engine sump and transmission unit housing.

Kalina Cross allows the owner to install wheels with a larger diameter, which also benefits both ground clearance and the exterior as a whole.

How to make this part for your car with your own hands

We will talk about the choice of fabric for covering a little later, but we will dwell on the material for the armrest itself in more detail.

Material selection

To bend the plywood, soak it in a bath of hot water

Don't forget to prepare the accompanying tools: meter tape, graph paper, and an electric jigsaw for cutting the board into parts.

Measurements for the future drawing

The manufacture of an armrest must begin by measuring the necessary parameters. To do this, arm yourself with a meter tape, a pen and a sheet of paper where you will write down all the data received.

Measure the distance between the front seats.
Holding the gear shift lever with your right (or left, depending on the location of the steering wheel) hand, determine the most comfortable height for the future armrest.
Measure the distance from the handbrake to the back of the seats.
To prevent the window sill from interfering with fastening your seat belts, measure the distance between their buckles.
If you plan to install the armrest in such a way that it will be partially located above the handbrake handle, then move it to the on position, and then measure the dimensions and height of the rise.
Measure the area where your product will be attached.

measure the distance between the seats to find out the size of the future armrest

Element design

When creating a project, draw a diagram of the armrest taking into account all sizes and proportions. For more accuracy, draw the part from both the side, front and back. Don't forget to label the lengths of the sides: it will be easier for you to transfer the markings to the material.
Make a drawing for the upper part of the armrest - the future cover.
Consider how to attach the lid: will it tilt or bend. Depending on this, determine the location of the grooves or other fasteners.
If the part is not strictly rectangular in shape, carefully work out the bends.
Determine in advance the lengths of the screws that will be used in the work. If their sizes differ in different parts of the product, indicate this on the diagram.
Decide how the armrest itself will be installed: using special fasteners or tightly fixed between the seats. If necessary, add grooves to the diagram at the bottom of the structure.

using the data obtained from measurements, build a diagram of the future armrest

After the drawing is ready, it needs to be transferred to graph paper (it can be purchased at any store selling sewing supplies) with strict adherence to all parameters. Be extremely careful: this pattern will serve as a model for making an armrest in the future.

Soft rest for your elbow in Kalina

Most drivers, when driving, and even more so when parking, like to rest their elbow on the armrest, it’s much more comfortable. Our classic armrest is designed to be at the optimal height for elbow support, and the soft foam layer combined with hypoallergenic eco-leather gives a soft feeling! And the use of high-quality environmentally friendly materials (barez plywood, hypoallergenic eco-leather, branded carpet, natural glue) guarantees the preservation of your health!

Watch a video review of one of our armrests with a detailed analysis of all important aspects: