How to turn off the alarm in a car (16 alarm models) - all the methods that work


Most drivers don't know how to turn off the alarm on your car. But such a need may arise at the most unexpected moment, for example, if the car does not respond to the key fob. You can disable this system using different methods - by turning it off, using a secret button, and also using software. Next, we present to your attention detailed information on how to disable the “Starline”, “Tomahawk”, “Sherkhan”, “Alligator”, “Sheriff” and others, which are popular in our country.

Possible causes of failure

There are not many reasons why the alarm system failed. However, you must definitely understand them in order to know how to turn off the alarm on your car. So, the reasons include:

  • Presence of radio interference .
    This is especially true for megacities and places with large concentrations of cars and various electronics. The fact is that modern electronic devices are sources of radio waves, which under certain conditions can interfere and jam each other. This also applies to the signals emitted by car alarm key fobs. For example, if next to your car there is a car with a faulty alarm system that emits its own signal, then there are times when it interrupts the impulses sent by the “native” key fob. To resolve this, try moving closer to the alarm control unit and activating the key fob there. Internals of the alarm key fob
  • Damage to the key fob (control panel). This happens quite rarely, but this hypothesis should still be tested. This can happen due to a strong impact, getting wet, or for externally unknown reasons (failure of internal microcircuit elements). The simplest failure in this case is battery discharge . This should be avoided and the battery in the remote control should be changed in a timely manner. If you have a key fob with one-way communication, then to diagnose the battery, just press the button and see if the signal light lights up. If this does not happen, the battery needs to be replaced. If you use a key fob with two-way communication, then on its display you will see a battery charge indicator. If you have a spare key fob, try using it.
  • Car battery discharge . In this case, all systems of the machine are de-energized, including the alarm system. Therefore, it is necessary to monitor the battery level, especially in winter . If the battery is really low, you can open the doors simply with the key. However, when you open the door, the alarm system will go off. Therefore, we recommend that you open the hood and disconnect the negative terminal on the battery. To turn off the alarm and start the engine, you can try “lighting” it from another car.

The considered problems can be eliminated in two ways - with or without the use of a key fob. Let's look at them in order.

Safety precautions during dismantling

The basic safety rule when performing auto repair work is to de-energize the system. To do this you need:

  • Unscrew the nut of the clamping bolt on the negative terminal of the battery;

  • remove the terminal from the power supply pin;
  • take measures to prevent accidental short circuits at the battery terminals.

This precaution will prevent damage to the electrical circuit.

If the body needs to be lifted to remove equipment, measures must be taken to prevent it from falling off the jack. For this purpose, supports and wheel chocks are installed.

How to turn off the alarm without a key fob

To turn off the alarm without using a key fob, use one of two methods - emergency shutdown and disarming coding. However, in any case, for this you need to know the location of the Valet button, which allows you to switch the alarm to service mode . Otherwise, she will be “on edge,” and it will be impossible to approach her without consequences.

Varieties of “Jack” buttons

You can read about where the “Valet” button is located in your car in the manual or ask the specialists who install the “alarm”. As a rule, alarm installers place them near the fuse box, or under the front dashboard (there are also options when the Valet button was located in the area of ​​the driver's pedals, behind the glove compartment, under the steering column). If you do not know where the button is located, then focus on the location of the alarm LED indicator . If it is installed in the front left side of the cabin, then the button will be there. If it’s on the right or in the middle, then you also need to look for the button nearby.

If you buy a car second-hand, be sure to ask the previous owner about the location of the mentioned button.

The two methods presented (emergency and coded) are so-called “fast” methods. That is, they can be implemented in a matter of seconds without the need to climb and understand the car’s electrical wiring. Next, we will consider these two methods separately.

Options for the location of the “Jack” button

Emergency shutdown

In this case, in order to turn off the standard alarm, you must know the sequence of actions to be performed. As a rule, this is a certain sequence of turning the ignition on and off and several clicks on the mentioned secret Valet button. In each individual case, this will be its own combination (the simplest is to turn the key in the lock and briefly press the button). While you are looking for the secret button and remembering the PIN code, so as not to irritate everyone around you with the howling of your car, you can at least remove the terminal from the battery. The alarm will stop “yelling” and you, in a calm environment, will decide on your actions - either remove the battery and slightly deform it (sometimes it helps when it’s dead), or resort to unlocking by entering a code. Next, we will look in more detail at the combinations for alarms popular among domestic car enthusiasts.

Coded shutdown

The definition of “coded shutdown” comes from an analogue of a PIN code, which has from 2 to 4 digits, which are known only to the owner of the car. The procedure goes something like this:

  1. Turn on the ignition.
  2. Press the “Jack” button the number of times that corresponds to the first digit of the code.
  3. Turn off the ignition.
  4. Next, steps 1 - 3 are repeated for all numbers that are in the code. This will unlock the system.

However, the exact sequence of actions is indicated only in the instructions for your car or the alarm itself. Therefore, unlock only if you are completely sure that your actions are correct.

What causes a car security system to break down?

Any system that includes individual elements is subject to wear and tear during operation. Anti-theft systems are by no means exceptions. Emergency situations often arise that make the car owner seriously nervous.

Within the framework of the problem presented, it would be quite appropriate to make a small digression. You need to understand that the uninterrupted operation of a car’s protective systems depends on a number of factors. At the forefront is comprehensive systematic maintenance and care of the elements of this device.

How to turn off car alarms

The simplest, but “uncivilized” and emergency method of turning off the alarm is to cut the wire that goes to its sound signal with wire cutters. However, most often such a number will work with old alarm systems. Modern systems have multi-level protection. However, you can try this option. To do this, use the mentioned wire cutters or simply pull out the wires with your hands.

Another option is to locate the relay or fuse that supplies power and controls the alarm. As for the fuse, the story is similar. The old “alarm” may turn off, but the modern one is unlikely to. As for the relay, finding it is often not an easy task. It is necessary to go by the opposite method to find its location. The situation is complicated by this fact. that often in modern alarm systems the relays are contactless and can be placed in unexpected places. But if you are lucky enough to find it, disconnecting it from the circuit will not be difficult. This will de-energize the alarm. However, the described methods are no longer suitable for emergency shutdown, but for alarm service . Although it is better to entrust this process to professionals.

Next, let's move on to a description of how to disable individual alarms, which are popular in our country among car enthusiasts.

How to disable “Sheriff”

How to disable the “Sheriff” alarm

Let's start with the Sheriff brand, as one of the most common. The algorithm for unlocking it looks like this:

  • it is necessary to open the car interior with a key (mechanically);
  • turn on the ignition;
  • press the Valet emergency button;
  • turn off the ignition;
  • turn the ignition back on;
  • press the Valet emergency button again.

The result of these actions will be the alarm exiting the alarm mode into the service mode, after which you will be able to find out the cause of the malfunction in the system.

How to disable “Alligator”

Alarm kit "Alligator"

The ALLIGATOR D-810 alarm can be turned off in two modes - emergency (without using a transmitter) and standard (using the “Valet” button). The choice of coded mode is selected by function No. 9 (see the section in the manual called “Programmable functions”). The standard shutdown mode consists of the following steps (with function No. 9 enabled):

  • open the car interior with the key;
  • turn on the ignition;
  • in the next 15 seconds, press the “Jack” button once;
  • turn off the ignition.

Note! After completing the described procedures, the alarm will not be in the service mode (“Valet” mode). This means that if the passive arming function is activated, then after the next time the ignition is turned off and all doors are closed, a 30-second countdown will begin before directly arming the car.

It is also possible to switch the alarm to service mode using a code. You can install it yourself. The numbers used can be any integer value in the range from 1 to 99, except those containing “0”. To disarm you must:

  • open the car interior with the key;
  • turn on the ignition;
  • turn off and turn on the ignition again;
  • in the next 15 seconds, press the “Jack” button the number of times that corresponds to the first digit of the code;
  • turn off and on the ignition;
  • in the next 10...15 seconds, press the “Jack” button the number of times that corresponds to the second digit of the code;
  • turn off and turn on the ignition.

Repeat the procedure as many times as there are numbers in your code (no more than 4). If you did it correctly, the alarm will go into service mode.

Remember that if you enter the wrong code three times in a row, the alarm will become unavailable for some time.

Next, let's look at how to turn off the ALLIGATOR LX-440 :

  • open the salon door with the key;
  • turn on the ignition;
  • within the next 10 seconds, press the “Jack” button once;
  • turn off the ignition.

After completing the described procedures, the alarm will not be in service mode. To remove the lock using a personal code, proceed similarly to the previous description. However, please note that this alarm code consists of only two digits , which can be from 1 to 9. So:

  • open the door with the key;
  • turn on, turn off and turn on the ignition again;
  • after that, in the next 10 seconds, press the “Jack” button the number of times that corresponds to the first digit;
  • turn off and turn on the ignition again;
  • within 10 seconds, using the “Jack” button, similarly “enter” the second digit;
  • turn off and turn on the ignition again.

If you enter the wrong code three times in a row, the system will be unavailable for about half an hour.

Alligator alarms have a normally open blocking relay. Therefore, it will not be possible to disable it by simply removing the connector from the alarm control unit. But with the STARLINE alarm, such a number will work, because there the blocking relay is normally closed.

Installing a new

The installation of a new security system is carried out in the same way as the dismantling of the old one. Carefully follow the instructions included in the kit. You can place the elements in the same places where they were installed previously. However, we recommend choosing a new location for at least the VALET button, so that no one except you knows about this location. Let's look at general installation recommendations

The unit should be located inside the car under the dashboard. Do not install it in areas with elevated temperatures (heater radiator, heater pipes), or where it can be touched by moving parts in the cabin (pedals, steering rack).

The impact sensor must be tightly attached to the car body from inside the passenger compartment. It is not recommended to install it on plastic or other non-metallic elements, as this reduces its sensitivity. The optimal location for its placement is the engine shield.

The optimal location for installing the antenna is the upper area of ​​the windshield. If the glass has heating filaments, then the antenna rod is directed horizontally. If there are no threads, then vertically.

Attach the electrical wiring to fixed elements of the interior, or to standard harnesses using plastic ties.

Important! If the alarm system has auto-start, GSM or satellite communication functions, advanced blocking, and several sensors, then we recommend installing it in a certified service. Errors in installing and configuring such systems can lead to serious vehicle damage.

How to turn off the Starline alarm”

Disabling the Starline alarm

Sequence of actions to disable the Starline 525 alarm :

  • open the car interior with the key;
  • turn on the ignition;
  • in the next 6 seconds you need to hold down the Valet button;
  • after this, one sound signal will appear, confirming the transition to the service mode, and the LED indicator will go into slow blinking mode (it lights up for about 1 second, and goes out for 5 seconds);
  • turn off the ignition.

If you have a Starline alarm model A6 installed, it can only be unlocked using the code . If the above models also have a personal code installed, then the algorithm of actions will be as follows:

Keychain Starline

  • open the interior with the key;
  • turn on the ignition;
  • in the next 20 seconds, press the “Valet” button the number of times that corresponds to the first digit of the personal code;
  • turn off and turn on the ignition again;
  • again, within 20 seconds, press the “Valet” button the number of times that corresponds to the second digit of the personal code;
  • turn off the ignition.

Instructions for disabling the alarm system STARLINE TWAGE A8 and more modern:

  • open the car with the key;
  • turn on the ignition;
  • within no more than 20 seconds, press the “Jack” button 4 times;
  • turn off the ignition.

If you did everything correctly and the system is operational, you will hear two beeps and two flashes of side lights, which notify the driver that the alarm has entered service mode.

Price for withdrawal in the service

If it is necessary to dismantle the security system, a reasonable option would be to contact a specialized service center. However, you may be surprised that the price of such work will be close to the price of installing a new one and will be at least 2,000 rubles. The work will be more difficult and more expensive if:

  • alarm with feedback;
  • equipped with autostart;
  • there are additional engine locks;
  • there are GSM or satellite modules;
  • the system is combined with an immobilizer;
  • information from the door switches is taken not from the CAN bus, but through separate non-standard electrical wiring;
  • Additional sensors are installed (tilt, volume, motion).

For each of these points, you can safely add 500-1000 rubles to the price of the work. Especially if it will be necessary to search for and remove non-factory wiring.

Important! Unskilled garage repairmen may charge a small fee for this work. However, the quality of their work leaves much to be desired. They may not only not complete the job, but also damage the car.

How to disable Tomahawk alarm

Disabling the “Tomahawk RL950LE” alarm

Let's look at unlocking the Tomahawk alarm using the RL950LE model as an example. You must act in the following sequence:

  • open the car with the key;
  • turn on the ignition;
  • within the next 20 seconds, press the “Jack” button 4 times;
  • turn off the ignition.

If unlocking is successful, the system will notify you with two sound signals and two flashes of signal lights.

How to turn off the Sherkhan alarm

Let's start the description with the SCHER-KHAN MAGICAR II . The sequence of actions is as follows:

  • open the car with the key;
  • within 3 seconds it is necessary to turn the ignition from ACC to ON 4 times;
  • turn off the ignition.

If you did everything correctly, then in confirmation the car will turn off the siren, the dimensions will blink once, and after 6 seconds two more times.

Disabling SCHER-KHAN MAGICAR IV is performed according to the following algorithm:

  • open the car with the key;
  • within the next 4 seconds, you need to turn the ignition 3 times from the LOCK position to the ON position;
  • turn off the ignition;

If you did everything correctly, the alarm signal will disappear, and the side lights will blink once, and after 5 seconds 2 more times.

If you have SCHER-KHAN MAGICAR 6 , then you can disable it only by knowing the code. When installed, it is equal to 1111. The sequence of actions is as follows:

  • open the car with the key;
  • within the next 4 seconds, you must have time to turn the ignition key 3 times from the LOCK position to the ON position;
  • turn off the ignition;
  • turn the ignition key from the LOCK position to the ON position as many times as the first digit of the code;
  • turn off the ignition;
  • Next, you need to repeat the steps of entering all the digits of the code with the ignition turned off.

If the information entered is correct, then after entering the fourth digit, the alarm will blink its side lights twice and the siren will turn off.

Please note that if you enter the wrong code three times in a row, the system will be unavailable for half an hour.

If you did not manage to meet the designated time (20 seconds) and find the “Jack” button, let the alarm calm down and calmly look for the mentioned button. After you have found it, close the door again and repeat the procedure. In this case, you will have enough time to turn off the alarm.

Be sure to remember or write down the first two digits of the code. They are used to record codes for new key fobs.

Basic principles of car alarm dismantling

Dismantling a car alarm does not fundamentally depend on its model or make of car. It doesn’t matter whether it’s a simple anti-theft device or a sophisticated Starline, whether it’s on an old domestic VAZ or a new foreign car.

The main thing in this matter is thoughtful, careful work with mandatory compliance with instructions. Carelessness and haste when independently dismantling electrical circuit elements can lead to problems in the operation of the car. Electronics require careful and attentive treatment. You should not get down to business if there is no complete clarity in the procedure and confidence in your abilities.

It should be remembered that manufacturers have provided for a situation in which car thieves may try to steal someone else's vehicle. If there is unauthorized intervention in the anti-theft device, the engine is blocked and the siren begins to howl. Manufacturers complete their products with special keys to deactivate the head module. You need to find a secret lock and insert the key into it.

How to disable the Leopard alarm

LEOPARD LS 90/10 EC alarm is similar to the previous case. An emergency mode of alarm removal is also possible using a personal code. In the first case, the actions are similar - open the car, get into it, turn on the ignition and press the “Valet” button 3 times. If you need to enter a code, then the steps will be as follows - open the door, turn on the ignition, press the “Valet” button as many times as the number corresponds to the first digit of the code, turn the ignition off and on and enter the remaining numbers in the same way. If you did everything correctly, the alarm will turn off.

Disabling the LEOPARD LR435 occurs in the same way as the case described.

The battery is low

If you are convinced that the key fob is working, then most likely you are dealing with an uncharged battery. Get close enough to the car and press the key fob. This will clear the alarm, but it is unlikely that the engine will run with a low charge. Before parking your car, be sure to check:

  • is the light in the car turned off?
  • are the lights, music, radio turned off;
  • what is the battery charge level?

How to disable the CENMAX alarm

the CENMAX VIGILANT ST-5 brand alarm will be as follows:

  • open the door with the key;
  • turn on the ignition;
  • press the emergency shutdown button four times;
  • turn off the ignition.

Disabling the CENMAX HIT 320 occurs according to the following algorithm:

  • open the interior door with the key;
  • turn on the ignition;
  • Press the “Jack” button five times;
  • turn off the ignition.

If you did everything correctly, the system will respond to this with three sound and three light signals.

How to disable the FALCON TIS-010 alarm

To put the immobilizer into service mode, you need to know the personal code. Sequencing:

  • open the door with the key;
  • turn on the ignition, the indicator will light continuously for 15 seconds;
  • when the indicator flashes, quickly, within 3 seconds, you must press the “Jack” button three times;
  • after this, the indicator will light up for 5 seconds and begin to flash slowly;
  • carefully count the number of flashes, and when their number matches the first digit of the code, press the “Valet” button (the indicator will continue to flash);
  • repeat the procedure for all four digits of the code;
  • If you entered the information correctly, the indicator will go off and the system will be switched to service mode.

If you want to transfer the car for long-term storage without an alarm function (for example, to a car service), you can use the built-in “Valet” mode function. For this purpose, the immobilizer provides a “disarmed” mode. If you need the “Jack” mode, then proceed in the following sequence:

  • disarm the immobilizer;
  • turn on the ignition;
  • within the next 8 seconds, press the “Jack” button three times;
  • after 8 seconds, the indicator will light up in a constant mode, which will mean that the “Jack” mode has been activated.

How to disable CLIFFORD Arrow 3

To enable the “Valet” mode, you need to enter a code. To do this, follow the following sequence of actions:

  • press the PlainView 2 switch located on the vehicle's dashboard or console x1 button the required number of times;
  • press the unlabeled button (if you need to enter “0”, you must press the button immediately).

To enable the “Valet” mode, you need to:

  • turn the ignition key to the “ON” position;
  • enter your personal code using the PlainView 2 button;
  • hold the unlabeled button pressed for 4 seconds;
  • release the button, after which the LED indicator will light up in a constant mode, this will serve as confirmation that the “Jack” mode is turned on.

To turn off the “Valet” mode you need to:

  • turn on the ignition (turn the key to the ON position);
  • Enter your personal code using the PlainView 2 switch.

If you did everything correctly, the LED indicator will turn off.

How to disable KGB VS-4000

Disabling this alarm is possible in two modes - emergency and using a personal code. Let's start the description with the first method:

  • open the doors with the key;
  • turn on the ignition;
  • within the next 10 seconds, press and release the “Jack” button.

If you did everything correctly, then in confirmation the siren will emit two short beeps, and the built-in speaker of the key fob will emit 4 beeps, and the icon LED will flash on its display for 15 seconds.

To unlock the alarm using a personal code you must:

  • open the car door with the key;
  • turn on the ignition;
  • within the next 15 seconds, press the “Valet” button as many times as the number corresponds to the first digit of the code (remember that the first press of the button must be no later than 5 seconds after turning on the ignition);
  • if you have more than one digit in the code, then turn off and turn on the ignition again and repeat the entry procedure;
  • When all the numbers have been entered, turn off and turn on the ignition again - the alarm will be cleared.

If you entered the wrong code once, the system will freely allow you to enter it again. However, if you make a mistake a second time, the alarm will not respond to your actions for 3 minutes. In this case, the LED and alarm will work.

Results

Finally, I would like to draw your attention to making sure you know where the “Jack” button is located in your car . After all, it is thanks to it that you will be able to turn off the alarm yourself; check this information in advance. If you bought a car secondhand, then ask the former owner for the location of the button so that, if necessary, you know how to turn off the alarm on the car so that its engine will start and you can continue to operate it. Also, be sure to find out what kind of alarm system is installed on your car, and accordingly, study the sequence of actions to disable it.

What to do if the engine does not start after turning off

If, after disabling the anti-theft device, the engine refuses to start, then, if you have certain skills, you can disconnect the housing yourself. For this purpose, the latches and screws are removed from it.

Attention! The latches and screws must be removed extremely carefully; opening the body of the anti-theft device must be done very carefully so that any fastening element does not break.

If the motor is blocked by a program, it is better not to try to fix the situation yourself, but to seek help from professionals.

Rating
( 1 rating, average 5 out of 5 )
Did you like the article? Share with friends:
For any suggestions regarding the site: [email protected]
Для любых предложений по сайту: [email protected]