VAZ 2115 wiper size - wiper length

Choosing windshield wiper blades for the VAZ 2115 is not difficult. This process is simplified by the identical sizes. The car was produced for a short period of time, only one generation was sold. This greatly simplifies the process of searching for parts.

Buying windshield wiper blades is a trivial task for the owner of a VAZ 2115. You can easily purchase them at any car store. Despite the fact that the car has long ceased to be produced. It is only important to study the dimensions in advance and also understand the fasteners.

What is the size of VAZ windshield wiper blades

It is very important to choose the correct size of windshield wiper blades, otherwise unpleasant problems may arise.
So, if the windshield wiper blades are larger than needed, the downforce will drop, which will ultimately reduce the quality of cleaning the vehicle's windows. Also, if the brushes are much larger, they may even “climb” onto the rubber seal, which will reduce the surface area that is in contact with the windshield wipers and the quality of cleaning will significantly decrease. If the brushes are smaller than expected, then due to the small cleaning area, the overall level of efficiency of the windshield wipers will decrease. Plus, an island of dirt and water forms in the center of the windshield, which will significantly impair visibility while driving. Let us recall that in the previous article we looked at why the stove fan does not work and how to repair it yourself.

Size of windshield wiper blades for Lada Samara series cars (2115, 2114 and 2113)

These cars leave the factory with seven-fold windshield wipers, which are 51 centimeters long. If replacement is necessary, you can use a 53-centimeter-long windshield wiper for the driver's wiper, but on the passenger side you will have to leave a 51-centimeter-long blade, since if you install an extended wiper, a “waterfall” will form in the center of the windshield.

Note that Lada Samara cars also have rear wipers. Cars leave the factory with a windshield wiper 30 centimeters long, but you can install a blade 33 centimeters long - this will not cause any problems. Note that, if you wish, you can even install brushes 40 centimeters long, but you will need to move a couple of teeth on the wiper motor to adjust its stroke.

Size of windshield wiper blades on VAZ 2108, 2109, 21099, 2110, 2111 and 2112 cars

All models of cars produced by the AvtoVAZ automobile concern indicated in the title of this section of the article are the progenitors of the Lada Samara series. It is for this reason that their front wipers are symmetrical, just like those of their descendants, and have a length of 53 centimeters.

Lada Kalina windshield wiper blade size

Lada Kalina cars have non-symmetrical wipers. So, on the driver’s side the wiper blade is 60 centimeters long, and on the passenger side – 40 centimeters. At the same time, liberties with the size of the driver’s “wiper” are not allowed, but the passenger one can be increased to 41 centimeters. The rear windshield wiper blade on the Lada Kalina is 36 centimeters long.

Lada Priora windshield wiper blade size

Lada Priora cars are equipped with asymmetrical windshield wiper blades. On the driver's side, the wiper is 53 centimeters long, and on the passenger side it is 50 centimeters long. As in the case of the Lada Kalina, liberties are allowed only with the passenger “windshield wiper”. You may notice a standard windshield wiper that is either 48 centimeters or 51 centimeters long. The rear wiper on the Lada Priora is 33 centimeters long.

Lada Granta windshield wiper blade size

Lada Granta cars inherited the glass cleaning system from the Lada Kalina car. In this regard, the length of the driver's windshield wiper is 60 centimeters, and the passenger's is 40 centimeters, but it can be replaced with a windshield wiper 41 centimeters long.

Acura Audi BMW Cadillac Chevrolet Chrysler Citroen Daewoo Dodge Fiat Ford GMC Honda Hummer Hyundai Infiniti Isuzu Jaguar Jeep Kia Land Rover Lexus Mazda Mercedes Mitsubishi Nissan Opel Peugeot Porsche Renault Rover Saab Seat Skoda Ssang Yong Subaru Suzuki Toyota Volvo VW

Best Wiper Blades

Which windshield wiper blades are better?

quality car wipers

Frameless wiper blades were invented in the 1980s. The first developments appeared from Bosch and Valeo. The main problem that had to be solved was the good attachment of the brush to the leash. In 1991, Bosch patented the first functional unit. But the first frameless Bosch brushes with leads, the design of which was quite reliable, appeared in 1997 (since this unit in the first brushes was not strong enough, and it took 6 years to improve its design).

Windshield wiper blades play a significant role in creating safe conditions when driving a car in rain or snow. They should ensure effective cleaning of the windshield from dirt and precipitation, which will allow you to correctly navigate in any road situation. As cars developed, the size and curvature of windshields increased. To ensure normal cleaning of the glass, as well as greater adherence of the brush to the glass, the length of the windshield wiper blades has increased. This worsened visibility and reliability of the structure.

Which wipers are better

Advantages of frameless brushes:

1. It is better to clean the windshield, because... The metal plate provides uniform pressure along the entire length of the brush and fits tightly to the glass.
2. The low height of the brush and the original profile of the belt allow it to have high aerodynamic characteristics. The air flow bends around the frameless brush more easily, which helps reduce drag and reduce the pressure of the air flow pushing the brush away from the glass, reducing noise: at a speed of 120 km/h. Also, an “integrated spoiler” is additionally installed on the brushes - a profile with a special curvature. This helps increase downforce at high speeds.
3. A frameless brush is less susceptible to icing, because does not have joints in which water freezes, and the brush no longer fits tightly to the glass along its entire length. The cleaning quality of a frameless brush will only change for the worse if ice appears directly on the rubber band.
4. The lower profile of these brushes improves visibility.

Disadvantages of frameless brushes:

1. Before you buy frameless brushes, you look at the price. This is the main reason; it is the price that makes car owners think when choosing brushes for their car.
2. The attachment to the leash for a regular frame brush turns out to be massive, which reduces the superiority in aerodynamics.
3. Having design features (stripes made of elastic steel with bending “spring” strips exactly repeating the curvature of the car glass), frameless wipers cannot be universal and will give the best effect only if they are intended for installation on a given car model.

So overpaying for frameless wipers is not always justified. Despite this, the future belongs to frameless brushes. Many manufacturers have the technology for producing frameless windshield wipers. To increase resistance to low and high temperatures, snow, rain and reagents in the production of windshield wiper blades, various rubber additives are used:

1. Rubber tape effectively copes with rain and snow, road slush and dirt.
2. Silicone tape is ideal for use in harsh climatic conditions and is more resistant to washing liquids and road reagents.

How to choose the right wipers for a car? reviews of windshield wiper blades for VAZ 2110-12

1. Which wipers for your car did you choose?
2. Impressions and comments on the operation of the brushes?

Selection of the size of wipers VAZ 2114

The size of the windshield wiper blades on the VAZ 2114 and other cars determines the downforce, especially for frameless wipers. If, for example, the brush is too large, the clamping force drops and the glass is no longer cleaned as well. In addition, large wipers can come off the working surface - this is due to the fact that their edge hits the windshield sealing rubber. And Kalina has a typical problem when the windshield wiper hits the driver's door. The main disadvantage of brushes that are too short is the reduction in working surface area. Also, the short length of the wipers on the VAZ 2114 leads to the formation of islands of dirt and the accumulation of water during rain. The size of the rear wipers on the VAZ 2114 is 30 cm, but 33 cm rear wipers are also acceptable - this will not lead to any problems. But brushes 40 cm long already require an increase in the stroke limit so that the wiper does not touch the rear window seal and does not go down too low. To do this, you need to remove the motor and return it back with an offset of a couple of teeth.

Modern auto wipers VAZ 2114

Windshield wiper blades for VAZ 2106: which ones to choose

Leading manufacturers especially recommend modern frameless brushes VAZ 2114 to car enthusiasts.

• more dense, uniform pressure to the glass;
• less restriction of field of view for the driver;
• high-quality cleansing without streaks in both directions;
• no noise from air flow.

Although frameless wipers have a slightly shorter service life, they are considered the best, and therefore cost a little more.

A very important factor in safety and comfort while driving a car is the removal of dirt and water from rain from the rear window. The rear wiper of the VAZ 2114, with a speed regulator, which is located inside the car, turning in both directions, copes with its functional tasks perfectly.

Dimensions for different models

For the VAZ 2109, 21099, 2108 models, the size of the VAZ 2114 windshield wiper blades is suitable - these models have the same body and the same glass. The length of the VAZ 2114 windshield wiper blades is also suitable for the VAZ 2110, 2111, 2112 models. For the Lada Kalina, the optimal sizes are the following: rear blade - 36 cm, passenger blade - 40 cm, driver's blade - 60 cm. The size of the patios on the Priora is the same as for VAZ 2114: rear wiper - 33 cm, passenger - from 48 to 51, driver - 53 cm. Cars of the Grant model require almost the same size of wiper blades as Kalina. These dimensions are as follows: the passenger wiper is from 40 to 41 cm, and the driver’s wiper is 60 centimeters.

Similar articles:

• What to do if the rear light does not light...
• What does the burning light mean...
• The main reasons for the increase...
• Replacing light bulbs in the dashboard...
• Why can't they burn...

• 
  Clutch Wire Adjustment

Post navigation

Features of choosing brushes for the VAZ-2115

First of all, you should know the recommended part sizes. We already talked about this earlier in the article.

Next, evaluate the quality of the wiper material. The tape and brush should be the same color and texture, and there should be no burrs or burrs on the elastic material.

Design features of the wiper:

Experienced drivers stock up on at least two sets of brushes, one used in summer, the other in winter. Because summer wipers become dull in winter and do not clean the windshield at all.

Which manufacturer should you prefer?

In the following list we will look at the most popular brushes that have proven themselves in everyday use by domestic car enthusiasts:

1. Champion. The company claims that approximately 25% of the automotive market is equipped with its brushes. The product has a patented bromine coating, which significantly extends the service life of wipers (up to 30%).
2. Rainbox. These products have also proven themselves well in the Russian market. The wipers are frost-resistant, which allows you to use them both in summer and winter, so as not to buy two sets.
3. Valeo manufacture their products using Silencio technology using rubber and graphite. This solution allows you to use wipers in any weather conditions and even in severe frosts.
4. Bosch. The products of this company are known to almost every motorist. The competitive advantage of wipers from this manufacturer is the use of two-component rubber. Accordingly, the brushes will last much longer than analogues from other companies. But when buying such windshield wipers, you will need to shell out more money, because these are premium products. However, based on the reviews, we can conclude that it is worth it.
5. Mayak brushes are budget products made in China, which have a significantly shorter service life compared to Bosch.

To summarize the article, we note that windshield wipers on a car are a fairly important detail. The quality of cleaning the windshield in rainy weather and beyond directly depends on the correct dimensions of the installed parts.

Now you know what parameters to pay attention to when choosing wipers for a VAZ-2114, as well as which manufacturers you can trust.

The size of the vase wipers should be selected based on the model’s recommendations; the factory sets the blades at 51 cm, but you can also install them at 53 cm (only on the driver’s side). If you install brushes from another car (and they are suitable for mounting), the downforce will decrease, which is why the glass cleaning will not be as good as with the original ones. So, how to change wipers correctly and choose the right blades?

“VAZ” windshield wiper blades – dimensions

With the arrival of the autumn-winter period, the driver faces many problems: checking the technical condition of the engine, switching to winter tires, protecting the body from corrosion. But the most important task is to ensure good visibility. Snow, rain, slush - all this settles on the windshield, and if the wipers cannot cope with cleaning, then driving turns into complete torture.

Owners of VAZ family cars can choose from a wide range of windshield wiper blades. Along with classic frame wipers, frameless wipers, which practically do not freeze to the glass, are also in great demand today. In order for the brush to clean the glass surface well, it is made of frost-resistant rubber on a graphite base.

It is also important to choose the right size brushes. If you choose larger or smaller brushes, this can lead to the fact that they will cling to each other, knock on the racks, and uncleaned streaks will remain on the glass. Size information is indicated in the catalogue.

Let's try to figure out what size windshield wiper blade is needed for a particular VAZ model.

VAZ model range

Lada – VAZ 2101 – VAZ (LADA) 2107

Zhiguli is the first name that many still use today. This generation is considered to be a VAZ classic. Compact sedans and station wagons were produced with rear-wheel drive, and the visual difference between these models was the shape of the headlights: round (VAZ 2101 and 2102), twin (2103, 2106), rectangular (2104, 2105, 2107).

The dimensions of the windshield and rear window are the same for all these models; the recommended size of the windshield wiper blades on both the driver and passenger sides is 330 millimeters. However, as many car enthusiasts note, larger brushes - 350 millimeters - are quite suitable here.

LADA “Sputnik”, “Samara”, “Samara 2”, LADA 110-112

VAZ 2108, 2109, 21099, and 2113-2115 - all these models leave, or left, the factory with a standard wiper blade size of 510 millimeters. It is also possible to install brushes measuring 530 millimeters, or 530 for the driver and 510 for the passenger. For LADA 110-112 models, the size of the front windshield wipers is 500 millimeters. For all models of this series, where a rear windshield wiper is provided, the blade length is allowed within 280-330 millimeters.

Domestic class “A” hatchback OKA-1111

“OKA” was equipped with one front windshield wiper blade and one rear one. Dimensions - from 325 mm to 525 mm.

LADA Kalina and Kalina 2

Manufacturer's recommended brush sizes:

• driver - 61 centimeters;
• passenger - 40-41 centimeters;
• rear brush – 36-40 cm.

LADA Priora, Lada Largus

Original wiper blade sizes:

• 508 mm – both front wipers and one rear.

It is also possible to install brushes with a length of 51 centimeters, or a combination of 53 on the driver’s side and 48-51 on the passenger’s side. The same original (factory) brush sizes are also for LADA Largus .

LADA Granta

Granta is produced from the assembly line with the following sizes of windshield wiper blades:

• 600 millimeters – driver’s seat;
• 410 millimeters – passenger seat.

NIVA

The dimensions of the brushes on the VAZ 2121, 21214, 2131 coincide with the dimensions for the VAZ 2101-2107, that is, 330-350 millimeters. If you are the owner of a Chevrolet-NIVA, then 500 mm wipers will fit here.

All sizes indicated are recommended by the manufacturer. Although some variations on the size of windshield cleaning brushes are possible.

What to look for when choosing windshield wiper blades?

First of all, you need to pay attention to the following factors:

• compliance of sizes with the manufacturer’s requirements, although you can deviate slightly from the standard sizes;
• versatility of fastening;
• quality of materials;
• price category.

The brush is pressed against the glass with a certain force, therefore, if you choose larger brushes, the quality of cleaning will deteriorate. You can choose a suitable brush size using catalogs produced by manufacturers. The easiest way is to measure your installed wipers with a tape measure. In addition, the packaging indicates which models this brush is suitable for. If you have original brushes installed, which are difficult to find on sale, then you can simply change the rubber blade itself.

It often happens that the glass area cleaned with brushes does not provide a normal field of view. This is especially noticeable on older cars. In this case, you can install a larger brush on the driver's side and a smaller one on the passenger's side. This is how you can remove the strip of water - “snot”, which constantly flows from above.

Pay special attention to adapters - fastenings for attaching the blade to the windshield wiper arm. The most common type of fastening is Hook. Not all manufacturers produce brushes that would fit VAZ mounts. In this case, you need to look for additional adapters in the kit.

The quality of the tape is the main component of a good windshield wiper blade. A high-quality tape runs without burrs or irregularities. It has a uniform color and texture. Graphite, silicone and Teflon tapes can last much longer, but at the same time their price is quite high.

( 6 ratings, average: 5.00 out of 5)

Size of wipers for old VAZ models

Most older VAZ models use a standard blade length of 33 cm. For the VAZ 2110 windshield wiper, as well as the “nines” - the same as on the 2114. Although they are interchangeable, it is still recommended to buy original blades - they are optimized for downforce . Their mounts are identical.

By the way, it is worth noting that for many models the size of the windshield wiper blades is indicated not in centimeters, but in inches. Eg:

• series 14 are the same ones that are suitable for vases 2107, 2105, 2106 and the like, the design of which is taken from a “penny”;
• series 18 - suitable for Niva (VAZ 2121);
• series 20 - standard for the “fourteenth” model and so on.

To simplify the calculation, you just need to remember that 1 inch is 2.54 cm. Using a simple formula, the length of the required brush is calculated.

If you place a longer windshield wiper in front of the driver than in front of the passenger, then when the water is removed, there will be no thin strip left on the glass. If you install two equally long windshield wipers, it will be there (but there will be no place on the sides that is uncleaned from dirt).

Some manufacturers, by the way, still produce so-called frameless wipers for VAZ. They are considered the best, but cost a little more. Their advantage is a tighter clamp and less restriction of visibility for the driver. But such windshield wipers wear out much faster. As for the material, the best choice is a special rubber for glass. Silicone, in principle, is not bad either, but it does a worse job of cleaning dirt without moisturizing. And during operation it produces an unpleasant “glass” creak.

Which brushes are best to choose for a particular car? It is worth focusing on your own experience. The main difference will only be in size. Some people prefer rubber ones, some prefer silicone ones, and others just want to save money.

For the latter, you can completely restore the old brushes (applies only to frame models). If they make an unpleasant squeak during operation, this means that they need to be cleaned of salts. The easiest way to do this is with a citric acid solution.

Wiper sizes

The size on the driver and passenger sides is the same. Therefore, there is no need to purchase a pair from different manufacturers. Look for sets that fit in size. You can simply buy two brushes 500 mm long. Some modifications are also equipped with a rear hemisphere brush. Its size is 350 mm. The replacement algorithm is no different.

Another advantage of the VAZ 2115 is that there is no need to install brushes of a strictly defined length. It is also possible to supply brushes with a length of 600 mm. They will not touch the edge of the body. Stains from areas that have not been cleaned will also be absent. But it is advisable to buy brushes of a specified length: otherwise the load on the splines and trapezoid will be greatly increased.

Original articles

There is simply no need to look for original parts. Their characteristics are no different from other brands.

In addition, AvtoVAZ does not independently produce brushes. They are purchased ready-made, used on the assembly line or sold in AvtoVAZ branded packaging.

Replacement options

There are also various replacement options. To date, all models on sale can be divided into the following categories:

• frame,
• frameless,
• hybrid,
• winter.

All wipers have their advantages and disadvantages. When choosing a specific type, it is very important to take into account all the nuances. Vehicle operating mode, region, driving speed.

Frame

The term "classical" is also used. They differ from other parts of this type by the presence of a metal frame. This makes the brushes heavy.

When driving at high speed, the wipers rise slightly above the surface of the windshield. Which reduces the contact area. As a result, certain cleaning problems arise. At the same time, the design is durable. It is even problematic to break them on purpose.

Frameless

This type is characterized by an optimal aerodynamic shape. As a result, there are no problems when cleaning at high speed. The contact patch remains unchanged. But their cost, as a rule, is an order of magnitude higher than frame ones. At the same time, wipers are lightweight and easy to damage.

Hybrid

Such models do not have the disadvantages of classic, contactless ones. The working surface is made from a single piece of rubber. But there is a metal frame inside.

The unique aerodynamic shape allows you to clean the windshield well even at high speed. There are no installation problems. Hybrid brushes are usually several hundred rubles more expensive than frameless brushes. But the price is completely justified by the ease of use.

Winter

Winter wipers are distinguished by their elasticity - even at sub-zero temperatures they clean the glass well. The secret lies in the presence of rubber in the rubber. It retains its elasticity even at temperatures well below zero. Length may vary. Winter wipers are made by many different companies.

Optimal price-quality ratio:

It should be noted that wipers of this type will be indispensable for those operating a car in the Far North. Since the contact patch is with the windshield, elasticity is maintained at almost any negative temperature. The tight fit ensures high contact density. Thanks to this, you can easily move at high speed and not worry about the quality of your view.

When purchasing wipers, you should give preference only to eminent and well-established manufacturers. The cost of such products is slightly higher. But the quality is guaranteed.

Rear window wiper

What size wiper blades are needed for the rear window? Most models are equipped with standard ones - 33 cm. It is possible to replace them with longer variations of brushes, but you need to take into account that the electric motor is less efficient. Accordingly, if you use a wiper that is too long, it may jam, for example, if snow has stuck to the glass. Frameless wipers should not be installed at the rear - they are simply not needed there. Their only advantage is resistance to freezing (and only if the rubber is frost-resistant). As a last resort, you can always reverse using the side mirrors.

By the way, on the VAZ 2115 from the factory, wipers with a blade length of 42 cm are installed on the rear window. It should be understood that the shorter the wiper, the better it cleans the grip area. That is why it is recommended to set it shorter than recommended by the manufacturer. The optimal option, according to many car enthusiasts, is better used on the VAZ 2110. There, the length of the rear windshield wiper is only 27 cm. Yes, it cleans practically nothing on the sides, but the central part is always well cleaned. They can also be installed on the VAZ 2115.

How to maintain and replace brushes?

To replace the windshield wiper blade 2110, just bend the rocker arm and then unfasten the rubber band. The frame structure itself must be lubricated with silicone oil.

For servicing the rear, the same rules are used. But frameless wipers have an initially curved shape.

The fastening there is done directly along the rocker arm.

Maintenance of brushes consists solely of timely cleaning of salts and derivatives of the washer fluid (dyes may remain after it - in cheap variations). This should be done either with a special solvent or with a solution of citric acid (immerse for 10 - 15 minutes, then wipe thoroughly with a rag). If even after this the brush does not clean the glass properly, it is time to replace it, since it has literally worn down to the ground. At the same time, the pressing force decreases, and the shape of the brush may differ from the initial one.

In general, which wipers are better is up to each individual to decide. With length everything is very clear. It should be remembered that if there are cracks in the glass, the wipers will wear out very quickly, and in order to increase their wear life, the rocker arm should be lubricated with silicone oil in a timely manner.

Choosing windshield wiper blades for the VAZ 2115 is not difficult. This process is simplified by the identical sizes. The car was produced for a short period of time, only one generation was sold. This greatly simplifies the process of searching for parts.

ATTENTION! A completely simple way to reduce fuel consumption has been found! Don't believe me? An auto mechanic with 15 years of experience also didn’t believe it until he tried it. And now he saves 35,000 rubles a year on gasoline! Read more"

Dimensions

The size on the driver and passenger sides is the same. Therefore, there is no need to purchase a pair from different manufacturers. Look for sets that fit in size. You can simply buy two brushes 500 mm long. Some modifications are also equipped with a rear hemisphere brush. Its size is 350 mm. The replacement algorithm is no different.

Another advantage of the VAZ 2115 is that there is no need to install brushes of a strictly defined length. It is also possible to supply brushes with a length of 600 mm. They will not touch the edge of the body. Stains from areas that have not been cleaned will also be absent. But it is advisable to buy brushes of a specified length: otherwise the load on the splines and trapezoid will be greatly increased.

Original articles

There is simply no need to look for original parts. Their characteristics are no different from other brands. In addition, AvtoVAZ does not independently produce brushes. They are purchased ready-made, used on the assembly line or sold in AvtoVAZ branded packaging.

Replacement options

There are also various replacement options. To date, all models on sale can be divided into the following categories:

All wipers have their advantages and disadvantages. When choosing a specific type, it is very important to take into account all the nuances. Vehicle operating mode, region, driving speed.

Frame

The term "classical" is also used. They differ from other parts of this type by the presence of a metal frame. This makes the brushes heavy. When driving at high speed, the wipers rise slightly above the surface of the windshield. Which reduces the contact area. As a result, certain cleaning problems arise. At the same time, the design is durable. It is even problematic to break them on purpose.

Frameless

This type is characterized by an optimal aerodynamic shape. As a result, there are no problems when cleaning at high speed. The contact patch remains unchanged. But their cost, as a rule, is an order of magnitude higher than frame ones. At the same time, wipers are lightweight and easy to damage.

Hybrid

Such models do not have the disadvantages of classic, contactless ones. The working surface is made from a single piece of rubber. But there is a metal frame inside. The unique aerodynamic shape allows you to clean the windshield well even at high speed. There are no installation problems. Hybrid brushes are usually several hundred rubles more expensive than frameless brushes. But the price is completely justified by the ease of use.

Winter

Winter wipers are distinguished by their elasticity - even at sub-zero temperatures they clean the glass well. The secret lies in the presence of rubber in the rubber. It retains its elasticity even at temperatures well below zero. Length may vary. Winter wipers are made by many different companies. Optimal price-quality ratio:

It should be noted that wipers of this type will be indispensable for those operating a car in the Far North. Since the contact patch is with the windshield, elasticity is maintained at almost any negative temperature. The tight fit ensures high contact density. Thanks to this, you can easily move at high speed and not worry about the quality of your view.

When purchasing wipers, you should give preference only to eminent and well-established manufacturers. The cost of such products is slightly higher. But the quality is guaranteed.

Selecting windshield wipers by size

When choosing, not only the type, but also the size of the windshield wiper blades for the VAZ-2110 is of great importance, so we will dwell on this issue in great detail. Many of our car enthusiasts try to be guided by simple logic - the larger the wipers, the better. We are sure that this opinion is wrong and are ready to prove our point of view.

How to determine the size of windshield wiper blades? To answer this question, you can either look at the specifications of your car, where this data is indicated, or measure the wipers yourself with a tape measure or ruler. You also need to measure the glass itself - this will help you comply with the following basic rules:

• wipers cannot extend beyond the glass;
• Under no circumstances should the brushes adhere to each other, as this will prevent them from properly performing their main functions.

As practice shows, the optimal size of windshield wiper blades for VAZ-2110 cars is 51 centimeters - on both the driver and passenger sides of the windshield. In this case, you can vary this parameter, but by increasing it for one “janitor”, you will have to reduce the size for another.

If you install three cleaners on your car at once, their dimensions should be as follows:

• for the windshield on the driver's side, the length of the brush cannot exceed 50 centimeters;
• a 450 mm long wiper is mounted on the passenger side;
• The rear window uses a windshield wiper whose size is 30 centimeters.

Remember that strict adherence to the requirements for the size of windshield wiper blades allows you to ensure their flawless operation, a tight fit to the glass and high efficiency in cleaning it from dirt in any weather. Therefore, do not engage in amateur activities, trying to increase the length of the wipers.

On both the driver and passenger sides, the length of the windshield wipers for the VAZ 2110 is 20″ (508 mm), the rear wipers are 11″ (279 mm).

Possible sizes of wipers on the VAZ 2110:

The sizes of windshield wiper blades for this VAZ model depend on their location.

Wiper parameters for hatchback, sedan and station wagon:

• Length of driver's windshield wipers: 508 mm (20″).
• Passenger wiper length: 508 mm (20″).
• Rear wiper length: 279 mm (11″).

Important: it is possible to install wipers of alternative sizes on the VAZ 2110, but in this case one of them must be shorter than the previous one. For example: on the driver’s side the length of the brush is 510 (mm), on the passenger side - 450 (mm), on the rear - 300 (mm)

For example: on the driver’s side the length of the brush is 510 (mm), on the passenger side - 450 (mm), on the rear - 300 (mm).

Other names:

Until 2014, the VAZ 2110 model was assembled under license from AvtoVAZ vehicle kits at the Bogdan Corporation automobile plant under the Bogdan-2110 brand.

Subtleties of the model range:

The model is equipped with an electronic engine control system, a diagnostic unit (on-board computer), power steering, electric windows, and a new body painting technology is used.

Years of production Years of production: 1995-2007.

Possible sizes of wipers on the driver's side for VAZ 2110 of all years of production.

Data in inches.

Passenger (in) Front passenger side:

Possible sizes of wipers on the driver's side for VAZ 2110 of all years of production.

Data in inches.

Rear (in) Rear:

Possible sizes of rear wipers for VAZ 2110 of all years of manufacture.

(General form)

500 (mm) 500 (mm) —

Possible sizes of wipers on the driver's side for VAZ 2110 of all years of production.

Data in inches and (mm).

Passenger (in) Front passenger side:

Possible sizes of wipers on the driver's side for VAZ 2110 of all years of production.

Data in inches and (mm).

Rear (in) Rear:

Possible sizes of rear wipers for VAZ 2110 of all years of manufacture.

Data in inches and (mm).

Lada 110 Sedan 1996 500 500 x 1997 500 500 x 1998 500 500 x 1999 500 500 x 2000 500 500 x 2001 500 500 x 2002 500 500 x 2003 500 500 x 200 4 500 500 x 2005 500 500 x 2006 500 500 x 2007 500 500 x 2008 500 500 x 2009 500 500 x

Disclaimer: Although the data represents official manufacturer figures, the information above is for reference only and is not guaranteed to be completely accurate. For cars of the same model manufactured for the USA, Europe and Japan, the size of the wipers may differ.

Replacement

The replacement algorithm is completely standard. Includes main steps:

• move the wiper arm to a vertical position: perpendicular to the windshield;
• We squeeze the plastic housing of the mount with our fingers and gently rock the wiper out.

If in the future the driver plans to use the part on the car, then all procedures must be performed carefully. In the cold, plastic becomes brittle. Sudden movements may cause damage. As well as strong blows. Installation is done in the reverse direction. Before use, you need to make sure that the wiper is firmly installed in its seat.

It is enough to pull it away from the bend of the hook. This will avoid many problems. When developing at high speed, a poorly secured wiper can simply tear off while driving. Which will lead to damage to following cars or even to an accident. The installation must be carried out in accordance with all the rules; special instructions in Russian are attached to the wiper.