What are eyelashes on car headlights and why are they needed?

It's very easy to apply eyelashes. But it should be remembered that eyelashes are different from eyelashes. Eyelashes bought on the market from someone unknown may not stick well, because it is unknown what they are made of. It is better to buy eyelashes from trusted companies in the store. And there will be no problems with the sticker. You can, of course, save money and cut out eyelashes yourself from vinyl film, for example, but will you succeed? Will your car look cheap with homemade eyelashes? So, what to glue with?

With double-sided tape

One way is to use 3M double-sided tape (preferably red). Scotch 3M is a success in eyelash stickers, but only if it is not a fake!

You need to glue in a warm room, preferably in warm weather. Clean the surface, degrease it and it’s better to warm it up a little, you can use a hairdryer, you can put a halogen lamp nearby (on a cold surface - it won’t last long). Don’t get it wet for a couple of days (don’t wash your car) and don’t go out into the cold right away. Apply the tape to the eyelash, cut along the contour and in one (!) precise movement - towards the headlight. Ready. To calm your soul and conscience, by gluing the eyelash around the perimeter with tape, you can apply a sealant into the cavity, but this is a “forever” option and do you need it? Natural eyelashes should not cover anything... And if they lie on the elastic bands, it is better to trim the eyelashes.

For adhesive sealant

For construction silicone sealant, which is sold in any hardware store.

This is another way to stick eyelashes. It holds very tightly, but then it’s a problem to tear off the eyelash. You just need to choose a water- and heat-resistant sealant.

Transparent adhesive sealant. It is still in a tube and fresh - white. And when it completely hardens, it becomes transparent. Wash everything until perfectly clean, degrease. We take the eyelash, spread it with sealant, then take the place on the headlight where we are going to glue it. Apply the eyelash to the headlight. We remove excess sealant. Then we use masking tape to tighten it properly. The car should sit in the garage for a couple of days.

And finally, a video to help.

Eyelashes for headlights on KIA - decoration or necessary accessory

KIA cars are quite popular in Russia for many reasons. And their expressive appearance is one of the features that the owners want to improve a little. How to connect fog lights to a viburnum. For example, purchase and install

eyelashes for headlights of KIA Ceed
, Range or any other model.
Gills on the eyelashes add visibility to turn signals

And we will study why they do this and how this process occurs within the framework of this publication.

Psychology of decoration

no one will say that installing eyelashes will make the car go faster or reduce fuel consumption How to connect fog lights to a viburnum:. A short guide on how to adjust the light of a Niva car. Properly adjusted headlights on a vehicle are a prerequisite for safe operation. This desire reveals a prestigious trait, such kitsch, as if this is not plastic products or a car, but the business card of a successful person (see article - tuning the headlights on a Pajero). how to remove the headlight and replace it, how to remove the headlights, how to install a Touareg headlight. And the perception of its owner depends on how expressive it turns out to be. In this case, about a KIA car enthusiast.

An artistic look at eyelashes for cars

If a painter looks at this action, he will definitely associate it with the finishing touch on the painting.

See:

The hands of the “owner-artist” lovingly apply the finishing touch

Moreover, since the eyelashes for KIA Sid headlights are purchased unpainted, the whole process:

recalls the process of creating an artistic canvas.

The plastic eyelashes have yet to be painted and installed

In such creativity, the car owner shows his desire to improve the appearance of his car, which is generally commendable.

Vaz how to install eyelashes on headlights and how to attach them. (stas alekseev)

EARNING ONLINE IN CASHBERY I invite you to Twitch.

New KIA concept car – designers never stop experimenting with the shape and placement of headlights

Note! KIA passenger cars were initially produced taking into account fashion trends. How to remove a headlight on a Nissan Qashqai video. Rinks 05 May 2022. Are your headlights original? My headlights have a completely different base in the low beams. From the Briza model of the 70s to ultra-modern concept cars, the shape of the optics is constantly changing.

Benefits of overlays

• the ability to minimize the gap between the hood and the headlights;
• creating an original appearance of the front of the car;
• simplicity and low cost of tuning;

Flaws:

• some difficulties with fastening;
• the likelihood of losing eyelashes when moving at high speeds.

We install it ourselves

If you are more interested in the practical side of the issue, and are not at all concerned about the opinions of others, as well as psychology, then the following instructions will allow you to quickly and correctly install this decoration on your KIA car.

1. we buy plastic blanks;
2. we paint them in a color that we choose ourselves;
3. arm yourself with double-sided tape;
4. We use it to secure the eyelashes on the headlights.

Tip: making headlight stickers would also be a useful addition. This transparent film, when hit by a stone, will distribute the kinetic energy over a larger area, thereby protecting the headlight from damage (see article - KIA headlight repair). Video: how to adjust headlight of astra headlight do-it-yourself car repair, how to adjust headlights on an Opel Astra g, how to adjust headlights on an Opel Astra g. How to remove a headlight on a Tuareg The Volkswagen Touareg has bi-xenon headlights with gas-discharge lamps. Its price is significantly lower than the cost of a headlight unit from a car dealer.

And now about the same thing, but in more detail:

• degrease the surface
  of the plastic eyelash. To do this, we will use antisilicone - a special degreaser for sealant. You should not use alcohol-containing solvents; they may prevent the paint from drying properly;
• Using a can of paint, paint it and leave it to dry. Quick-drying automotive paints allow parts to be used in literally 30-40 minutes;
• degrease the surface
  of the headlight;
• We mount a strip of tape on the back of the eyelash and tear off the protective paper layer;
• Apply it to the surface of the headlight and press it.

That's it, the work is finished and you can operate your car.

KAMA EURO-532 205 60 r16 tires will be a good addition to your car - elegant and reliable.

Using vinyl and tinted film for manufacturing

This method is the simplest and fastest, and when used, it takes 5-10 minutes to make products. True, they will look worse than those that require a lot of time and a large amount of materials to produce.

Making eyelashes from film is quick and easy

If you narrow the headlights using a black film, then such eyelashes will look harmonious on cars of the same color, but not very well on cars of a different color. But this problem can be easily solved, since finding a film that harmoniously matches the color of the car today is not at all difficult.

Having opted for vinyl film used for car wrapping, the driver can give free rein to his imagination. After all, its color range, sold through car dealerships, is very wide. And eyelashes cut from carbon-fiber vinyl will look very original.

How to make eyelashes for headlights from film: video

Among other things, headlight light does not pass through the vinyl film, while the tint film does. And in this case, the material for making eyelashes can be picked up near workshops that specialize in wrapping cars with vinyl - they always have a lot of waste.

Before you start making eyelashes, you need to make a cast of them. For this purpose, the upper part of the surface of the headlights should be covered with masking tape. This must be done so that it does not reach the central part a little. After this, using a pencil or marker, a drawing of future eyelashes is applied to the tape. It should be taken into account that too wide eyelashes can significantly reduce the luminous flux of headlights. And they won’t look very stylish.

Next, the tape is cut along the drawn lines. After this, you need to move some distance away from the car and look at what the eyelashes look like from different angles. If necessary, necessary adjustments should be made.

If everything is satisfactory, then the tape is carefully removed and the non-adhesive side is applied to the tape glued to the second headlight. The outlines of the template are copied onto it and the second set of cilia is cut out. The tape removed from both headlights is pasted onto the film. To do this, select the side on which there is no transparent protection. Now you can cut eyelashes from the film with scissors.

The resulting products are applied with the adhesive side to the surface of the headlights, which is previously degreased with a solvent. If the shape of the headlights is too convex, then the film must be molded during the sticker process. A hair dryer is used for this purpose.

General information about eyelashes

Eyelashes are small pads that fit tightly to the headlight and cover its part (usually the top) . The main function is decorative: such elements are used to visually change the shape of the optics, but they also serve as protection against mechanical damage and environmental influences if you are not driving very carefully.

Photo gallery: images of eyelashes on headlights

In addition to the variety of shapes and colors, the main parameter for classifying eyelashes is the material of manufacture. The most popular eyelashes are made from self-adhesive film, PVC and fiberglass. To understand which material is better to choose, we will consider the pros, cons and difficulties of working with each of them.

Kinds

What is a splitter, why is it needed and how to install it on a car

Manufacturers of automobile accessories offer three types of eyelashes for headlights, the differences of which lie in their purpose and characteristics.

1. Protective. Their main task, as the name suggests, is protection from mechanical damage. To make protective eyelashes, transparent thermoplastic is used, onto which the eyelash pattern fits perfectly.
2. Chrome plated. They are designed to create a harmonious design of the car's exterior. If the car already has chrome parts, then such eyelashes will serve as a good addition to them.
3. Plastic - without exaggeration, they can be called the most common linings. As a rule, they are universal and affordable.

However, often the car owner does not like industrially manufactured linings either because of their appearance or because of poor quality. That’s why many people prefer to make eyelashes with their own hands. It costs no more than buying factory products.

Types presented on the Russian market: video

https://youtube.com/watch?v=ThQgiDYAQi0

Craftsmen use several methods to make eyelashes. Each of them has its own advantages and disadvantages. Therefore, each owner chooses the option that best suits his requirements and needs.

Adhesive tape

Today you can find any colors and textures of self-adhesive film to make eyelashes for headlights from it.

The easiest way to make eyelashes is to use “self-adhesive”. To work with the film, no special skills or tools are required, it is cheap, you don’t have to paint it, you can choose any color, you don’t need to remove the headlights, and the entire process of making eyelashes will take you no more than 40 minutes.

It would seem that these are continuous advantages, but they are also disadvantages at the same time. The film is inexpensive, but it looks cheap on the car, does not require painting - and does not exactly match the body color, it is easy to use - and therefore anyone can do the same.

In addition, the service life of the film on the headlights is limited: the edges of the “self-adhesive” after washing lift up and tear, dirt gets clogged into scratches from stones, and after only 3 months of driving on Russian roads, such tuning will not improve, but will spoil the appearance of the car. Keep in mind that 10 years ago, when stores were not yet overflowing with car accessories, tuning studios were developed only in the capital, and ordering tuning via the Internet was just becoming a reality, eyelashes made from film could cause admiration and a desire to “do the same.” Today it is difficult to surprise anyone with them.

What you can make from plastic with your own hands

Plastic eyelashes look more presentable. The cost of a sheet of plastic is low, and you can buy it at a building materials store or at a manufacturing advertising agency. A wide selection of colors allows you to choose the material to match the color of the car and do without painting, and making eyelashes does not require any special skills from you. You will have to spend more time and effort on such eyelashes, since it is necessary to dismantle the headlight. For special tools, you will need a hair dryer.

The easiest way to make and install eyelashes for headlights

To make eyelashes you should use:

• PVC sheet 2–3 mm thick or other suitable plastic;
• construction hair dryer;
• Phillips screwdriver;
• three types of sandpaper for plastic (coarse, for initial sanding, for final sanding);
• degreaser;
• clean cotton rag;
• double-sided tape (or sealant);
• pencil.

As a rule, the headlight is mounted with 2-3 bolts from above and has additional lower mounts. Finding the upper mounts and unscrewing the bolts is not difficult (you will see them immediately after you open the hood), but to get to the lower ones, if they are present in your car, you will have to remove the bumper.

Then you need to act according to the algorithm below.

1. From the PVC sheet, cut a sufficient piece to fit the eyelash with allowances for the engine compartment and side parts of the headlight, bordering the radiator grille and wing.
2. Apply the cut sheet to the removed headlight and, heating it with a hairdryer, smooth it until the sheet completely follows the shape of the headlight.
3. Do the same with the second headlight. When the plastic hardens in the desired shape, outline the boundaries of the eyelashes on it with a pencil, leaving a small allowance - about 0.3 mm - and cut out according to the drawing.
4. Sand the edges with sandpaper, starting with the coarsest sandpaper to refine and level the edges, and moving on to fine sandpaper to get rid of possible nicks, scratches and make the edges perfectly smooth.
5. Let's move on to installation: clean and degrease the headlight, do the same with the inside of the eyelash.
6. After the degreaser has completely dried, we glue double-sided tape to the headlight, carefully attach the cover and enjoy the updated look of the optics.

Photo gallery: a simple way to stick eyelashes

Be careful with the hairdryer. The sheet may melt to a liquid state and you will ruin the workpiece. If you do not have experience in handling a heat gun, it is better to practice in advance on another sheet, heating it and studying how it will deform.

Before using a hairdryer, examine the material of your headlight. Nowadays, cheap optics from Chinese manufacturers have become widespread, which are often made not of glass, but of plastic. If one is installed on a car and you heat it with a hairdryer, the headlight can be thrown away.

I would like to add a few words about painting plastic eyelashes: it is believed that painting is not necessary, since you can match the plastic to the color of the car, and, if desired, change its color with self-adhesive film. But it is almost impossible to achieve an exact color match, and since the plastic is more matte than the paintwork of the car, the plastic eyelash may look foreign.

If the plastic wears out over time, it will look unattractive. Therefore, we recommend spending a little more time and painting the plastic eyelashes before installation.

How to dye eyelashes

To paint plastic eyelashes you should use:

• sandpaper;
• degreaser;
• clean cotton rag;
• cans of varnish, acrylic primer and paint.

Varnish, primer, and paint can be found in specialized stores that sell automotive paint. When purchasing, pay attention to the use of plastic materials. When choosing paint, if you want to match the color exactly, use your car's paint code, which is located on the metal plate under the hood (when the car has not been repainted).

Application of plastic

A more effective and impressive option would be a plastic eyelash. Buying material will not be difficult. Plus, there are a number of studios where you can get your decor done quickly and professionally. Moscow alone has dozens of such tuning studios.

But since the price is high, we do everything ourselves.

To work you will need:

First you will need to remove the headlight, and work with it in a dismantled state. Unlike the use of films, plastic lashes require removal of the optics.

Typically, headlights are held in place by a few bolts at the top and a mount at the bottom. How exactly they are removed depends on the specific car.

After dismantling the element, follow this algorithm:

• cut a piece of plastic, the dimensions of which will cover the surface of the optics with allowances on the sides;
• give the material an approximate shape of the future eyelash;
• attach plastic to the headlight;
• turn on the hairdryer and start heating the material;
• gradually the plastic will become softer and more flexible;
• give the workpiece a shape;
• wait for it to cool down;
• remove the workpiece from the headlight;
• Mark the desired geometry of the eyelash with a pencil, adding an allowance of literally 0.3 mm;
• trim off excess;
• sand the edges;
• degrease the headlight itself and the plastic blank;
• Use sealant or tape to secure the eyelashes.

I recommend that you provide protection for the glass of the headlight itself in advance so as not to damage it during the heating process with a hairdryer. Cover with some thick material and gently move the hairdryer over the surface without touching other areas.

Also, the plastic will then need to be cleaned, primed and painted if it does not exactly match the color of the body.

Fiberglass

For several reasons, this is the most difficult execution option: there is no ready-made material (the trim will have to be sculpted from scratch), the headlight must be dismantled, and painting is required. But the result is worth the effort: if you set out to make eyelashes from fiberglass, you will end up with a high-quality, durable product.

Easy way to make, paint and install

To make fiberglass eyelashes we need the following set of tools:

• crosshead screwdriver;
• masking tape;
• pencil;
• brush;
• epoxy resin;
• several sheets of fiberglass;
• primer;
• clean cotton rag;
• degreaser;
• putty;
• three narrow spatulas (3, 5 and 8 cm);
• grinding machine (grinder with grinding wheels or long and hard manual labor);
• acrylic paint;
• sandpaper;
• varnish

We dismantle the headlight and begin the process of installing the eyelashes.

1. We cover the headlight with masking tape (to avoid accidental contact with resin, it is better to cover it completely, and not just the part on which the eyelash will be placed).
2. We decide on the shape, make a stencil and cut out fiberglass fabric on it (from 2 to 5 layers for each eyelash; the quantity will depend on the quality of the fiberglass fabric and the volume of epoxy resin), with allowances for polishing the edges.
3. We begin to create a blank: using a brush, place a thin layer of epoxy resin on the headlight, carefully apply a pre-cut sheet of fiberglass, press, smooth and leave to dry. This is a slow process, the layer can dry from 1 to 5 hours, depending on the temperature and humidity in the room.
4. After complete drying, apply subsequent layers in the same way.
5. Then we remove the workpiece, correct the shape with coarse sandpaper and carefully sand the edges, removing the most obvious roughness on the eyelash.

And then we work according to the standard scheme, which was described above. We degrease, apply putty, wait until it dries, and sand. Degrease, prime, sand. We degrease, paint and varnish, wait until it dries.

It is easier to work with a removed headlight, but you can do without dismantling if you cover the adjacent elements of the car with film. Choose a thick film - thin epoxy resin will corrode.

Photo gallery: proven method of making eyelashes

We install it on the headlight using double-sided tape or sealant. Let's enjoy the victory! A lot of time and effort was spent, but such eyelashes look great and will delight the eye for many years.

Video: making your own eyelashes

Eyelashes for headlights made of epoxy resin and fiberglass

This option for making eyelashes is the most labor-intensive, but the quality of the product when used is at a very high level. At the same time, all the bends and design features are repeated down to the smallest detail. It is with the help of this method that eyelashes are obtained well for foreign-made cars, the headlights of which are heavily slicked, and their surface is curved in both planes. And covers for headlights with a corrugated surface can generally be made only in this way.

To make eyelashes, you will need the following tools and materials:

• fiberglass;
• epoxy resin, and if you don’t have it, you can use epoxy glue;
• household tape and masking tape;
• a brush with short and hard bristles;
• roller of small width;
• rubber gloves to protect the surface of the hands;
• respirator to protect the respiratory tract of a worker.

It is better to remove the headlights from the car before starting work. Firstly, it will be more convenient to work with them, and secondly, it eliminates the possibility of staining the surface of the hood or bumper with resin.

The surface of the headlight is covered with masking tape, onto the surface of which the contours of the eyelashes are applied.

The removed headlights are placed on a surface covered with oilcloth. The surface of the headlight is covered with household tape. Painting tape is glued over it. The latter should be applied in such a way that the joints of household tape are glued - this is done to eliminate the possibility of particles of epoxy resin or glue penetrating the headlight.

The contours of the eyelashes are drawn on the surface of the masking tape using a marker. This is necessary in order to determine the limit of gluing thin or thick fiberglass.

However, we must remember that thin fiberglass allows layers to be applied more accurately, especially in places where the glass is sharply curved. Making blanks using thin fiberglass will require more time.

Sequence of work:

1. Fiberglass is cut into narrow strips. Their length should be slightly greater than the width of the headlight.
2. Epoxy glue is diluted at the rate of 1 part hardener to 10 parts glue. Violation of the proportions can lead to the glue hardening too early or taking a very long time to harden. In this case, the strength characteristics will be violated.
3. Next, put on rubber gloves and apply a thin layer of resin to the tape. In this case, the contour of the drawn overlays should overlap by approximately one centimeter.
4. We lay thin fiberglass fabric on the resulting layer of resin. Its surface is rolled with a small roller until the epoxy resin shows through.
5. Another layer of epoxy glue is applied to the fiberglass with a brush, on top of which the fiberglass is again placed. In this case, the edge of the new layer should overlap the boundaries of the first by five millimeters. And again the surface must be rolled until the resin passes through the pores of the fabric. As a result of the roller treatment, all air bubbles should be completely removed from the space between the layers.
6. The last layer of fiberglass is generously filled with epoxy resin. The total thickness of all layers must be at least 4 mm. The finished product is left for about a day to allow the epoxy resin to dry completely. The headlight should be positioned in such a way that the surface of future eyelashes is strictly horizontal. This will avoid smudges and unevenness.
7. After the resin has completely dried, the covers are removed from the headlights. As a rule, this is not difficult to do - the surface of household tape is very slippery and masking tape comes off easily.
8. Now you need to remove all the tape from the surface of the headlights and wash them with some solvent or gasoline.
9. A pattern is applied to the eyelash blank with a marker, according to which it is cut using an electric jigsaw or grinder.
10. The cut trims are tried on the headlights. If everything is normal, then the surface of the eyelashes is treated with sandpaper. First, rough sanding is used, and then finishing is done using fine sandpaper.
11. The surface, treated to a perfectly smooth state, is primed and painted to match the color of the car body. In this case, as a rule, after applying the first layer of paint, small defects are revealed. They can be removed using finishing putty. The surface is again sanded, primed and painted. At least 3 layers of paint must be applied.
12. Well-dried eyelashes are attached to the headlights using double-sided tape.

LEDs as the basis for fashionable headlights

There are eyelashes that are mounted in the headlight housing, namely, from LED strip. However, on July 21, 2016, a new law was introduced to tighten measures for installing tuning. Ordinary eyelashes are not prohibited if their presence does not interfere with the supply of light.

LED tuning elements look stylish: it’s a pity that they are prohibited

But the installation of LED eyelashes is a change in the design of lighting fixtures not provided for by the manufacturer (except for those cases where LED eyelashes were installed on exactly the same model, but in a different configuration). For this, according to current legislation, you may face a completely legal deprivation of your driver's license for a period of 6 to 12 months. Is the game worth the candle? You decide.

Tuning does not have to be expensive and labor-intensive. Even without special training, you can create an original part with your own hands in a few hours, which will attract the attention of other car enthusiasts. Tuning your favorite car yourself is always a pleasant and interesting experience that you will remember every day when you look at the transformed car. Stock up on everything you need and try making eyelashes - you won’t regret it!