Changing the oil in a Renault Logan box: how much and what kind of lubricant should be filled

Replacement process

First of all, we recommend buying a “plug with washer” kit (7703 075 180 VAZ, 7703075180 Renault). The plug closes the drain hole (see fig.

). The required volume for changing is 3.1 liters of oil.

A new plug is screwed in here. To wash away all deposits, the replacement is made on a heated box. And it is better to replace it in the warm season.

The process of changing the oil in a manual transmission in a Renault Sandero Stepway is not very difficult, provided that there are no additional problems. And here it is worth considering one important point: if there are lubricant leaks, the origin of which is unknown, a knock is heard in the box, and after maintenance there are problems with gear shifting, you need to contact a specialist. It is not recommended to carry out repairs yourself if you do not have the necessary skills.

Spark plugs for Renault Logan - we'll tell you step by step It's worth mentioning the tools for changing the oil in a manual transmission in Renault Sandero Stepway. And the list here is very small. You need an 8-square wrench to open the drain hole, a screwdriver to remove the crankcase protection, a 4-5 liter container to remove used oil, and a canister of new lubricant (3-3.5 liters is enough).

Regarding safety precautions, everything is simple and clear:

The machine must be secured on a level surface. Stoppers are installed under the wheels, the car itself is put into speed and the handbrake is put on. It must be fixed carefully to avoid injuries and other troubles.
Before work, it is recommended to warm the oil to a warm state to reduce viscosity (especially important in the cold season). But you should not work with a hot manual transmission, to avoid burns due to hot lubricant getting on the skin or accidentally touching the gearbox housing.
It must be remembered that the oil should not enter the body.

And the process of preparing for draining the liquid is as follows:

The machine is installed on an overpass or above an inspection hole. It must be fixed according to the principle described above (in the safety regulations).
Using a screwdriver, remove the screws holding the crankcase guard in place. Then it is removed to the side until the replacement process is completed.
Place a pre-prepared container under the drain hole.
Wipe off dust and dirt from the gearbox (in particular, from the filler and drain plugs). During the process, you need to make sure that there are no leaks or damage to the manual transmission.

After completing the described procedures, you can proceed to the actual replacement process.

It is worth mentioning the tools for changing the oil in a manual transmission in Renault Sandero Stepway. And the list here is very small. You need an 8-square wrench to open the drain hole, a screwdriver to remove the crankcase protection, a 4-5 liter container to remove used oil, and a canister of new lubricant (3-3.5 liters is enough).

How to make a replacement

Replacing transmission fluid in a Logan gearbox is not that difficult. It is better to carry out the procedure on a warm engine and in the warm season, using tools and materials such as:

Elf 75W-80 grease;
carrying with a lamp;
10 mm spanners;
square slot screwdriver;
a large syringe or hose with a sealed funnel;
metal brush;
gasket for gearbox drain plug;
container for collecting oil with a volume of at least 5 liters.

Before starting work, warm up the box by driving 3-5 kilometers, then place the car over the inspection hole. To avoid trouble, be sure to secure the vehicle by applying the handbrake or placing a shoe under the rear wheel. Only then proceed with replacement.

Let's start with the manufacturer's recommendations!

The manufacturer's recommendations say nothing about the need to change the oil in the box!

The manufacturer believes that the oil will retain its properties throughout the entire life of the vehicle.

But we live in Russia, where there are no roads, a lot of dust and dirt and a temperature difference of 80 degrees, and all these conditions negatively affect the health of cars. Accordingly, when the grenade boots break and the oil seals wear out, dirt, dust and water inevitably get into the gearbox! Naturally, in Russian realities it is better to change the oil in the box, and the owners have experimentally established that this should be done after 60-100 thousand km. mileage or when repairing the box and related elements.

ELF Tranself NFJ 75W80 in the box of Logan 1.4 and 1.6 is 3 liters and it looks like this:

What kind of oil is allowed to be poured into a Logan box when operating in the Russian Federation?

Friends, let's agree that the recommendation of ELF Renault oil is nothing more than a marketing ploy... Oil viscosity is indicated according to SAE, and there is nothing wrong if you fill in high-quality GL4 synthetic oil with a viscosity of 75w-80 from any other manufacturer. The main thing is that the oil is of high quality.

Regarding the problem of choosing between mineral, semi-synthetic and synthetic, you should definitely choose synthetic oil, since it is more stable over the entire temperature range and has a longer service life. Although the author of this article has seen a Logan with a mileage of 280,000 km from a taxi, the owner of which poured Lukoil mineral water into the box, the author does not recommend doing this.

How to change the oil in a Renault Logan manual transmission with a 1.4 engine

We will need:

Vorotok
Square as for engine drain plug
10mm wrench or socket
Drain plug gasket
Oil drain container
Syringe or funnel for pouring oil.

Sequence of actions when changing the oil in a Logan 1.4 box

— unscrew the engine protection (it’s much easier and faster to work this way)

— prepare a container for draining the oil and unscrew the gearbox drain plug

— drain the oil until it runs out, use pliers to unscrew the filler plug on the box

— after draining the oil as much as possible, screw the drain plug back into place, having first replaced its gasket.

-using a syringe or funnel with a hose, pour oil into the box through the filler plug until it runs back! Usually exactly 3 liters of oil fit into the box.

— wipe excess oil from the box body, tighten the filler plug.

— screw the engine protection into place

- clean the box breather

— enjoy the result and count the money saved.

Well, for clarity, here is a video:

https://youtube.com/watch?v=u4FpzaX1I5I

How to change the oil in a Renault Logan manual transmission with a 1.6 engine

There is no point in writing separate instructions for changing the oil in the box of a Logan with a 1.6 engine, since the boxes differ structurally only in the size of the clutch housing, while the boxes themselves are the same and the filling volume of oil and its type are also the same. Therefore, you can do everything according to the instructions given above.

That's all for me today. Good luck to you, good luck on the roads and good health.

According to the owners' experience

In reality, Renault Logan owners act differently:

When the clutch basket was replaced, the oil was drained from the box. There was a good argument to replace the fluid completely, at the same time replacing the clutch cable, this is a disease.
The first replacement was made after 190 thousand kilometers;
When buying a car, the owner decided that the service interval would be 60 thousand km.

https://www.youtube.com/watch?v=u4FpzaX1I5I

190 and 60 – these numbers differ by an order of magnitude. And both are puzzling. Regarding the first point, we note that the owner prepared for the replacement in advance: the box was warmed up, the plug was purchased immediately. We advise you to do the same.

Find out more about the new Logan

How to remove and install the front door opening limiter on a Renault Logan
Renault Logan replacement front brake pads
Renault Logan engine temperature sensor replacement
How long can you drive with the fuel light on?
Logan gearbox device
Renault Logan: full technical specifications of the car
Electrical diagrams Renault Logan 2
3.1.2. Renault Logan Operation, maintenance and repair of Renault Logan cars since 2005. Checking the ignition coil, its circuits, high-voltage wires - “IMPORTANT FOR EVERYONE” - motor transport portal

Reliability jh3

The JH3 gearbox is considered a reliable unit, therefore it is still relevant in the automotive market. Car owners prefer cars with a structurally simple gearbox, partly because of its accessible and cheap maintenance. The disadvantages of manual transmission boil down to the lack of a high level of driving comfort.

The gear shift does not always occur clearly and quickly; sometimes there are jolts and jerking of the vehicle. Structurally, the unit has been fully studied, so even in the event of a serious breakdown, its overhaul will not be difficult. Usually the lever for switching from one speed to another becomes loose ahead of time, which leads to unclear switching.

Often, owners of Lada Largus with JH3 note the noisy operation of the manual transmission and a crunching sound when engaging reverse mode. Early wear of the synchronizers cannot be ruled out. If we close our eyes to some shortcomings, we will get decent mechanics that can go 200-300 thousand km without a single repair. There are known examples of cars that have covered about 500 thousand km on JH3 without a single repair. Much depends on your driving style and quality of service. The oil change must be carried out in accordance with the maintenance regulations.

New Lada: Lada Largus and Renault Logan comparison

When is it necessary to change the gearbox oil?

Oil drained from the gearbox at 60 thousand km. It was already very dirty, so the checkpoint was working with problems

However, despite the fact that the manufacturer (by the way, the plant was built in 2003) did not set a time limit for changing transmission oil and fluids, explaining that this is not required for the correct and smooth operation of the gearbox, experienced craftsmen and service center mechanics for servicing Renault cars, they recommend replacement every 60,000-100,000 kilometers (depending on conditions and operating time).

And on the other hand, no one is immune from the fact that before this cherished mileage occurs, the clutch will fail or the CV joint on the left side will not need to be replaced, and then changing the oil in the gearbox becomes a desirable procedure. To avoid premature failure, monitor the condition of the CV joint boots and change them if they are damaged!

According to the manufacturer's recommendations, the fluid in the Renault Logan gearbox is replaced every 60 thousand kilometers. Depending on the operation, the replacement schedule can reach up to 100 thousand kilometers, or vice versa, decrease down to 30-20 thousand. In this regard, it is necessary to regularly monitor the level and quality of the oil using a dipstick.

If the oil has reached the end of its service life, it will not be able to perform its intended functions. This means that the substance is not able to properly lubricate the rubbing components of the unit. This leads to rapid wear of parts.

The first to fail are the bearings, the failure of which can be indicated by symptoms such as noise and hum in the operation of the gearbox. Sometimes sounds appear when you turn on a certain gear. It is also possible for the speeds to switch off spontaneously. If you do not take immediate action to change the oil, the entire gearbox will fail.

Currently reading: Replacing stabilizer struts for Renault Logan - New Logan

Step by step replacement

1. Place the machine on a level surface.

2.Unscrew the engine and transmission crankcase protection. In some variations, the protection has a technological hole for unscrewing the drain plug.

3. Clean the gearbox housing from dirt and dust in the drain area and near the filler hole. If drained oil is to be reused, the area near the drain plug must be clean.

4.Unscrew the drain plug using a 8-square. After loosening it with a wrench/ratchet, we recommend turning the plug out manually to quickly remove it from the stream of draining waste. An increase in backlash indicates the end of the thread.

If the color of the drained oil is cloudy, with an emulsion, then there are water impurities in the oil.

5.Use pliers to unscrew the filler plug, which is located at the end of the right side of the box. It is not necessary to change the gasket on this plug.

6.Tighten the drain plug. It is advisable to replace the sealing gasket.

7. To fill in new oil, use a homemade funnel with a piece of hose or a special syringe for filling technical fluids. First pass the hose through the top of the engine compartment, and then direct it from below into the filler hole.

According to the manufacturer's instructions, there is no need to replace the fluid in the Renault LOGAN box. But car owners say otherwise. Owners believe that changing the oil in the Renault Logan gearbox affects the smooth transition from one gear to another.

In Logan, after a run of 100-120 thousand km, the seal density may be disrupted, and the volume of water in the gearbox begins to decrease. Changing the oil in the gearbox (manual transmission) Hyundai Solaris 1.6. According to auto mechanics, this is a more common cause of gearbox failures in Renault.

So if Logan’s gears start sticking in with a crunch, pay attention to the oil level

This can be done by checking the inspection hole. It is located on the box (front of the crankcase). You need to remove the plastic cover and run your hand along the edge of the hole. Changing the gearbox oil in Renault Sandero. If there is enough oil, it will be level with the edge. If the volume of fluid is small, most likely the problem is in the oil seal. Renault Logan oil change: which one to fill in. It needs to be replaced and the oil updated.

Possible malfunctions after replacement

The repair and operation manual for Renault Logan, Sandero, Largus, Logan 2, Sandero 2 states that the oil in the manual transmission is filled for the entire service life of the gearbox and does not require replacement. But during operation of the machine, the internal boot of the left drive often fails. The boot becomes tanned in the cold, breaks and water gets into the oil, which requires an oil change.

Currently reading: Renault Logan cigarette lighter does not work: repair, replacement, how to remove

When parking the car, check the lighting, it should be at a high level. Replacing used oil in a box in a Renault Logan requires unscrewing the crankcase protection - these are six bolts. When replacing, you should inspect the Renault Logan gearbox for external damage, because if they are not corrected in advance, changing the oil will not be enough.

The plastic filler plug in the boxes is unscrewed by hand, without the help of tools. Before replacing, you should check the oil level. This can be done with a small stick or finger.

Then, the drain plug is carefully unscrewed and the entire volume is drained into the prepared container. Before adding fluid, you should inspect the exhaust. If there are no mechanical particles or dirt in it, then in general the box is in order.

Changing the oil in manual transmissions and automatic transmissions in Renault Logan also recommends replacing the drain plug gasket, this is necessary so that it does not leak when topping up. The amount of oil poured into the automatic transmission depends on the volume of the barrel installed in the car. In the Renault Logan automatic transmission, oil is poured in the same way as in other cars, using a funnel and a hose. Next, all parts must be checked and screwed into place.

Which oil is better to choose for a manual transmission in a Renault Sandero Stepway?

Recommended oil for Renault Logan gearbox

From the factory, oil is poured into the gearbox, which is subsequently recommended for further use. For example, if there is a need to add a substance to the unit.

This mechanical oil has the following properties:

increased fluidity at low negative temperatures, which allows for simplified gear shifting in winter;
stable viscosity parameters, eliminating the possibility of noise when changing gearshift lever modes;
The product contains a formula that allows you to avoid arbitrary shutdown of gears;
the oil manufacturer guarantees consumers reliable protection of the mechanical components of the unit from rapid wear;
excellent thermal stability of the product to temperature changes;
the presence of a complex of additives in the fluid that allows for extreme pressure protection of gear teeth when the unit operates under high load conditions;
stability of the lubricant product to oxidation;
protection of internal parts of the gearbox from corrosion.

In automatic transmissions, the car manufacturer recommends using Elf Renaultmatic D3 SYN fluid.

The GARAGE NN channel in its video suggests familiarizing yourself with the procedure for changing the lubricant.

The quality of the oil used should be discussed separately. When filling, only all-season oils are used. Moreover, the liquid should be selected based on its viscosity level. Moreover, the viscosity is determined by the markings on the container with the lubricating fluid. The marking looks something like this: 80w-90 (or 80W90, depending on the manufacturer).

The first part should be labeled 75w, 80w or 85w. They designate, respectively, the minimum operating temperature of -40, -26 and -12 degrees Celsius. Therefore, it is recommended to fill in oil marked 75w - it is suitable for most regions.
The second part should be marked 80, 85 or 90. It is worth remembering that in all three cases the maximum operating temperature is considered to be 35 degrees Celsius. But the viscosity of these oils differs. Liquids marked 90 are considered the best in this regard.

All oils (both transmission and motor) are divided into three main types: synthetic, semi-synthetic and mineral. Synthetic lubricants are considered to be of the highest quality - they are recommended for use in Renault Sandero Stepway. It is recommended to use Elf Tranself NFJ 75w-80 API GL-4 fluid.

Oil selection

The manufacturer uses transmission lubricant ELF TRANSELF TRJ 75W-80 (No. 194757) or 75W-90 (No. 195286).

Good analogues include Casrtol Syntrans Transaxle 75W-90 and Motul Gear300 75 W-90. All of the listed oils have the necessary API specification tolerances: GL - 4. They have high lubricating and detergent properties.

The use of lubricants for a Lada Largus car with a different approval is not recommended. A different additive package may affect the functional qualities of soft metal box elements (synchronizers).

Semi-synthetic lubricants, for the most part, have mineral substances, some synthetic substances and a certain percentage of additives responsible for enhancing the properties of oils.

Synthetic fluids are based only on synthetic substances. Produced from hydrocacking substances with the addition of additives.

Synthetic gear lubricants have better characteristics than semi-synthetic ones, but are more expensive.

The choice of oil viscosity depends on the climatic operating conditions of Largus. Thicker lubricants have proven themselves to be excellent in hot conditions. Technical fluids with lower viscosity require less time to warm up in sub-zero temperatures.

Adviсe

Before starting work, travel at least 10-15 km so that the oil inside the gearbox warms up and becomes less viscous. If the sealing gasket of the filler plug is not torn and is elastic, it can be reinstalled. Pay attention to the processing status. The presence of an emulsion indicates mixing of oil and water

Often such a nuisance is a consequence of a leak in the boot of the inner CV joint of the left drive shaft. Therefore, inspect the boot for tears or loose clamps. Pay attention to the transmission breather, through which, if installed incorrectly, water and dirt enter the manual transmission. Often, after unqualified repairs, craftsmen neglect the correct installation of the breather. 4.For preventive purposes, rinse and blow out the breather with compressed air. As the pressure inside the transmission increases, a completely clogged "breather" valve can push out. If the malfunction is not noticed in time, dust, dirt and moisture will render the new gear oil unusable.

5. We recommend lubricating the engine protection mounting bolts with graphite grease.

Seal

Often such a nuisance is a consequence of a leak in the boot of the inner CV joint of the left drive shaft. Therefore, inspect the boot for tears or loose clamps. Pay attention to the transmission breather, through which, if installed incorrectly, water and dirt enter the manual transmission. Often, after unqualified repairs, craftsmen neglect the correct installation of the breather.4. For preventive purposes, rinse and blow out the breather with compressed air. As the pressure inside the transmission increases, a completely clogged "breather" valve can push out. If the malfunction is not noticed in time, dust, dirt and moisture will render the new gear oil unusable.

Seal

All the details of changing gearbox oil for Renault (Renault)

Checking the transmission fluid level in the Renault Logan gearbox is a troublesome but simple procedure, which is usually carried out in an inspection pit or on an overpass

It is important to ensure that the car is positioned strictly horizontally, without distortions, otherwise the lubricant will be underfilled

To measure the liquid, you will need the following:

container for collecting oil;
flashlight;
steel rod (probe);
8 and 10 mm wrenches.

Then insert a metal rod at a right angle into the filler hole, pull it out and inspect its surface. If the dipstick is clean, there is not enough lubricant. Add liquid using a syringe or funnel, then screw the cap back in.

The first step in properly changing the gearbox fluid is purchasing the right mixture. Remember that transmission mixture and motor oil are different products. And those motorists who calmly pour engine lubricant into the gearbox are at great risk. Before pouring new oil into the Renault Logan box, you need to drive a little, thereby warming up the lubricating fluid and mixing it (with dirt and impurities).

Advantages and features of ELF Tranself NFJ 75W80 oil:

The formula used in the creation process eliminates the problem of speed jumping;
Has heat resistance at the highest level;
Even in the most severe frosts, it retains a liquid structure for easy gear shifting;
EP additives for gearbox parts retain resistance to loads;
Protection against corrosion and oxidation;
Good viscosity stability and resistance to water.

For a safe replacement procedure, it is worth considering these examples of precautions:

Protective gloves and a gas extraction device must be used;
It is also necessary to use safety glasses;
Use only serviceable tools;
Use a hat if possible.

The list of tools used to change the oil is small:

8 mm square wrench.
Pliers.
Portable lighting.
Wire brush.
10 mm socket wrench.
Funnel with hose (0.5 m) or blower.
Container for draining used oil.

Axxis Power A LPG 10W-40;
Azmol Leader Plus 10W-40;
S-Oil DRAGON SL 10W-40;
ZIC A 10W-40;
Pennasol Super Light 10W-40.

Synthetics

Toyota / Lexus / Daihatsu SN 5W-30;
Pennasol Super Pace 5W-40;
Delphi Prestige Plus 5W-40;
Repsol Elite Multivalvulas 10W-40;
ZIC X7 LS 10W-40.

Axxis Power A LPG 10W-40;
Azmol Leader Plus 10W-40;
S-Oil DRAGON SL 10W-40;
Pennasol Super Light 10W-40;
ZIC A 10W-40.

Synthetics

Toyota / Lexus / Daihatsu SN 5W-30;
Pennasol Super Pace 5W-40;
Repsol Elite Multivalvulas 10W-40;
Delphi Prestige Plus 5W-40;
ZIC X7 LS 10W-40.

Synthetics

Toyota / Lexus / Daihatsu SN 5W-30;
Pennasol Super Pace 5W-40;
Repsol Elite Multivalvulas 10W-40;
ZIC X7 Diesel 10W-40;
ZIC X7 LS 10W-40;
Axxis Gold Sint A3/B4 5W-40.

The oil level in Logan 1.4 and 1.6 boxes should be (under normal conditions) up to the filler hole.

How to determine the level. It can only be understood by pouring a little oil into the gearbox filler hole. When it starts to flow back, the box is full.

Preparing the car

The oil level in the gearbox is controlled for long-lasting operation of the gearshift mechanism. When it becomes necessary to change the oil in the gearbox, it is recommended to prepare the car for this operation.

Manual transmission or automatic transmission, there is no difference, the oil poured into them requires heating. You need to drive in different gears and give the lubricant time to reach a working consistency. Then, the oil in the Renault Logan gearbox is much easier to change. Particles of dirt and old fluid are automatically released when drained.

Prepare a container to drain the old oil. Changing the oil in the gearbox requires an inspection hole to carry out the entire scope of work, and the oil level must also be checked there. It is recommended to prepare some kind of container so as not to dump the waste on the ground and not pollute the environment.

Criterias of choice

When choosing transmission fluid, pay attention to the specification and viscosity. The API classification is a generally accepted classification that, through testing, determines the effectiveness of extreme pressure and anti-corrosion additives

Elf Tranself NFJ 75W-80 corresponds to class GL-4, which is recommended for use in synchronized manual transmissions of passenger cars. However, it is permissible to use GL-4 and the highest class - GL-5, which is designed for loaded hypoid gears.

The SAE marking shows low-temperature (number with index W) and high-temperature characteristics. 75W formulations are recommended for regions where the temperature does not drop below -40°C. If the car is operated at temperatures not lower than -26°C, oils with an index of 80W are poured into the manual transmission. As for high-temperature characteristics, in regions with a temperate climate, a viscosity grade of 85-90 can be used.

Often it is not possible to pour Elf Excellium, and you have to choose from what is on the shelves. You can take any popular brand with a viscosity of 5W30 and 5W40 (synthetic). Next we will provide a list of budget oils for petrol and diesel Logan.

Level control and required volume

If it is necessary to change or add oil in the Renault Logan gearbox, the car owner needs to know how many liters are included in the transmission. The fluid volume in a manual transmission is about 3.5 liters. The amount of lubricant in automatic transmissions is 4 liters.

To check the oil level, do the following:

Warm up the car and place it on a flat horizontal surface.
There is no dipstick for checking the volume in Renault Logan. Diagnostics is carried out through the inspection hole, which is located in the front part of the transmission housing. There is a plastic cover in the hole; it must be wiped with a rag and unscrewed.
You need to look into the hole. If you cannot see the oil level, you should determine it by touch by placing your finger in the hole. The amount of lubricant should be around the bottom edge.

You can learn about checking the volume from the video published by user Roni.

Checking the transmission fluid level in the Renault Logan gearbox is a troublesome but simple procedure, which is usually carried out in an inspection pit or on an overpass. It is important to ensure that the car is positioned strictly horizontally, without distortions, otherwise the lubricant will be underfilled.

Oil change instructions

1. Place the machine on a level surface.

2.Unscrew the engine and transmission crankcase protection. In some variations, the protection has a technological hole for unscrewing the drain plug.

3. Clean the gearbox housing from dirt and dust in the drain area and near the filler hole. If drained oil is to be reused, the area near the drain plug must be clean.

If the color of the drained oil is cloudy, with an emulsion, then there are water impurities in the oil.

5.Use pliers to unscrew the filler plug, which is located at the end of the right side of the box. It is not necessary to change the gasket on this plug.

6.Tighten the drain plug. It is advisable to replace the sealing gasket.

For models 1.4 and 1.6, the steps will be similar, so this step-by-step instruction will be equally useful for everyone.

Remove the engine sump protection. We give ourselves convenient access to the necessary components of the car.
We prepare and place an empty container under the drain plug to drain the used oil.
Unscrew the drain and fill plug. We are waiting for the complete draining of the used transmission oil.
We screw all open plugs into place. If the gasket is damaged, it must be replaced with a new one.
Using a syringe (this is most convenient, but you can also take another device, such as a watering can with a long hose), pour new oil into the gearbox until it flows back out. As written above, 3-3.5 liters will be required.
We wipe away the stains and tighten the filler plug.
We install engine protection.

Safety precautions at work

Locate the drain hole. It is located to the left of the crankcase, between the engine and the left wheel. Then change the oil using the following algorithm:

Remove the crankcase protection by unscrewing the six bolts with a 10 mm socket wrench.
Clean the box body and drain hole from dirt with a wire brush.
Place a container under the drain hole to collect the transmission fluid, which will immediately pour out after unscrewing the plug.
Carefully unscrew the cap using a square-head screwdriver and collect the waste in a container.
Close the drain hole with a plug, replacing the rubber gasket with a new one.
Pour 3-4 liters of fresh material through the inspection hole using a hose with a funnel attached or a large syringe.

Add lubricant until it begins to flow out of the inspection hole. Then install the plug and return the crankcase protection to its place.

The oils in the Logan box are very flammable, avoid exposure to open flames. Before pouring liquid into the box, check all your tools for serviceability. The manufacturer recommends carrying out all operations with gloves, as you can get burned on the hot parts of the machine.

Outsider

There are three types of oil:

Mineral lubricant is the most affordable product recommended for use in old engines and in cars with high mileage. Various additives containing large amounts of sulfur are added to such oil, and this already suggests low quality oil.
Semi-synthetic oil is a higher quality product and is considered the best option in terms of quality and price. Such a liquid, however, contains more mineral composition, and therefore it is also better recommended for cars with high mileage.
Synthetic oil is the best option for the Renault Logan gearbox. This is the most fluid oil that never freezes at low temperatures, unlike the above two types. At the same time, due to its fluidity, such oil penetrates the parts of the box faster and more efficiently and lubricates them. In addition, synthetics are designed for a longer replacement period.

Which oil should I buy for Renault Logan mechanics?

Modifications of gearboxes that were used to aggregate Renault Logan with different types of engines do not make any difference when choosing an oil. From the factory, the Logan box is filled with Elf Tranself NFJ 75W-80 fluid.

When selecting an oil change fluid for a manual transmission, the specification and viscosity are taken into account. According to the API classification, it is recommended to use oils with a class of GL-4+, but liquids of classes GL-4 and GL-5 are also allowed.

Motul Motylgear SAE 75W-80

The lubricant viscosity recommended for operation in moderate climates according to the SAE classification is 75W-80, 75W-90, 75W-85.

Among analogues, preference is given to the following oils:

Castrol Syntrans V FE with a viscosity parameter of 75W-80 and API classification GL-4+;
Liqui Moly Getriebeoil - 75W-80 (with GL-5 specification);
Motul Motylgear SAE 75W-80 meets GL-5 standard;
Shell Getriebeoil EP 75w90 - GL-4;
Valvoline Maxlife MTF SAE 75W-80 (GL-4);
Castrol Syntrans Transaxle with viscosity 75W-90 GL-4+.

Valvoline Maxlife MTF SAE 75W-80 (GL-4)

What gear oil to fill in the Renault JH3 and JR5 gearbox

Manual transmission JH3 and JR5 can be installed on cars of the Lada Vesta, XRAY and Largus families, as well as many Renault models. The maintenance regulations for these vehicles do not provide for changing transmission oil. This means that the oil is filled for the entire service life. However, to extend the service life of this unit, experts recommend changing the transmission oil at least once every 50 thousand km. mileage Let's figure out which transmission oil is best to choose for manual transmissions JR3 and JH5.

Previously, AVTOVAZ published information on its official website about what technical fluids were poured into LADA cars from the factory. Tranself TRT 75W-80 TPM4501/B06138A oil was specified

synthetics.

The fuel consumption standards, which are available at every LADA dealership, indicate that when changing the oil in these transmissions, use Tranself NFJ 75w-80

(by the way, it is also recommended by Renault).

In fact, Tranself TRT 75W-80 is an old ELF product, which is now called Tranself NFJ 75w-80.

Why does the manufacturer recommend this particular oil?

The JH3 and JR5 manual transmissions use synchronizers with a brass locking ring. There is an opinion on the Internet that the manufacturer recommends Tranself NFJ 75w-80 mainly because of its class 1a corrosive effect on copper, that is, to protect brass synchronizer rings. And the front gears have oblique teeth, which are unpretentious to oil.

Conclusion

: Use gear oil recommended by the manufacturer. Using a different oil may result in pitting corrosion and increased wear on the brass synchronizer rings.

What kind of gear oil do you use?

Source

Disassembling the differential

Now you can start disassembling the differential. To do this, remove the locking ring:

Then take out the glass:

We turn the box over, pull out the oil seal (hitting one edge of the oil seal will warp and then you can pry it up and pull it out), under it there is another retaining ring. It also needs to be dismantled; this ring is pressed by the differential spring washer. To make removal easier, you can clamp the differential gear and housing in a large vice. This will make it easier to remove.

Now the differential is held in place only by seating in the bearings. We put something under the box and knock out the differential, striking the shaft through a drift. In this case, you need to be very careful not to clog the slots. Or better yet, use a straightening hammer. Some people hammer this differential on a piece of wood until it knocks it out

The wide spring ring should be installed as shown in the picture; pay attention to this when assembling. It serves to ensure the required bearing tension

In general, there are two rings, the thin one is stuck to the gear:

We simply knock out the large bearing; in order to press out the small one, you need to remove the speedometer drive and the retaining ring:

We pull up the speedometer shaft with narrow pliers and then take out the gear:

Then we take out the retaining ring and knock out the bearing.

How to change oil

There is no need to add lubricant to a 4 or 5 speed transmission. In accordance with the Renault Logan manufacturer's instructions, you only need to check its level and top up the fluid when servicing the car. However, Russian drivers constantly complain that the left boot, which is connected to the grenade and is washed with box oil, fails.

That’s why the experts “pull the blanket over themselves” - they advise changing the lubricant in the gearbox every 60 km. If you don’t change it, then the gearbox may fail - you will need capital. Due to the considerable cost of both the part itself and the work, replacing the fluid as a preventative measure will definitely save you money!

An oil change in the Logan gearbox is necessary, regardless of breakdowns or high mileage. If you have a new car, you need to change the oil after using the car for six months (or after 15,000 kilometers). Usually, at the factory, the oil in the box is slightly underfilled (according to standards), and while the box is running in, its parts inside (gears) are ground in.

Many people are accustomed to the mandatory change of transmission oil in manual and automatic transmissions. But, there are cars that do not need such frequent fillings, such as Logans. It is necessary to fill the Renault Logan gearbox with oil only in case of repair or complete dismantling of the mechanism.

In this case, the transmission fluid for Logan is selected very carefully in order to match the original as closely as possible. Therefore, having such a car, you need to know everything about how to pour oil into the gearbox.

If the oil seal flies on Logans, then transmission oil is automatically consumed in large quantities. It is then that changing the oil in the gearbox becomes simply necessary. Only high-quality factory oil goes into the Renault Logan box, and remember that you must control the volume so that there is no empty space.

Warm up the engine to operating temperature and then let it cool for 5-7 minutes. The oil drains better and faster if it is not cold. Hot temperatures can burn you, so it’s better to let the engine sit for a while. Open the filler neck of the cylinder block (where we will pour oil) and pull out the dipstick. If you give oxygen through, the liquid will flow out faster. We jack up the car and put it on supports. A necessary step for easy access to the drain plug. You can also use a viewing hole or overpass. Unscrew the drain plug with a wrench

Remember that used oil will be hot and take precautions to avoid skin burns. We pour the waste into the prepared container. Do not dump waste directly onto the ground! Unscrew the oil filter

If the filter is tightly clamped, a special removable filter wrench may be required. We install the new filter after lubricating its sealing ring with oil, and pouring a little oil right into the middle so that it absorbs. The number of the original oil filter is 8200768913. Cheaper analogues that are suitable for Logan: FRAM PH5796, MANN W753, MAHLE C467, FILTRON P6433, PURFLUX LS932 and many others. We tighten the drain plug after making sure that the washer located on its thread is intact. If necessary, it must be replaced (sealing washer). We lower the car from the racks and pour oil into the empty engine, guided by the dipstick. After the poured oil reaches the middle of the dipstick between the MIN and MAX marks, wait 3-5 minutes. Afterwards we warm up the engine for about 5 minutes and measure the level again. As a rule, after the first warm-up the level drops and we add as much as we need.

If they are noticeable, this may indicate wear on the pump. To completely drain the power steering, you can rotate the steering wheel left and right.

Replacing the sensor does not require much effort. At the rear of the cylinder block (where the unit number is indicated), press the wire lock and remove the terminal. The sensor itself is unscrewed with a key x 22. When installing a new sensor, make sure that there is a sealing washer.

This is done during an oil change, at approximately 15 thousand kilometers (officials call this figure). If you change the oil at 10 thousand, then it is better to change the filter to a new one.

What to look for when changing the oil

The durability of the gearbox depends on the quality of the fluid. The main thing in choosing oil for a Logan gearbox is not to go cheap and not choose an inexpensive mineral one. It is characterized by instability. Semi-synthetic and synthetic are much better suited for Logan's gearbox.

However, you should not mix different types of transmission fluid. For example, add semi-synthetics to synthetics. Or mix, for example, Elf and Motul, wanting to save money.

Some additives may precipitate and affect the operation of the gearbox gears. As the viscosity of the oil increases, it may clot and the gearbox will stop working. Therefore, it is better to choose one oil and stick to it in the future. If the manufacturer suddenly stops producing it, the oil should be replaced completely.

Hi all! It's been a long time since we talked about car maintenance. The last article I wrote is z, which you can find on our website. It's time to bring up this topic. The idea came to mind to write an article about changing the oil in a Renault Logan box. Since most Renault Logans are equipped with a manual transmission, this is what we will talk about.

Regarding my communication with the Renault Logan car, I can say that the boxes on them are very durable and unpretentious. The “mechanics” itself is a very relatively simple and reliable unit. And the Renault Logan manual transmission is no exception. However, you can “kill” any box. Therefore, the manual transmission requires at least some kind of care.

And the most important thing in servicing a gearbox is changing the oil in it. The manufacturer himself assures that the boxes on Renault Logan are not serviced and the oil in them is designed for their entire service life. I have an extremely negative attitude towards this newfangled trend. The fact is that all fluids, be it brake fluid, manual transmission fluid or power steering fluid, lose their properties over time. Those.

Over time, a liquid that does not fulfill its intended purpose will undoubtedly cause harm to the box. And a car owner who blindly believes the words of automakers will end up with expensive transmission repairs. But you and I are not like that and we understand that an oil change in the Renault Logan gearbox is required and that is why you are here. Right? Then let's get down to business.

Mechanics Renault Arcana 1.6 l JR5

As a manual transmission, the Renault Arcana 1.6 with front-wheel drive has a JR5 gearbox with 5 gears, which was developed directly by Renault. In addition to the crossover, it is also installed on many other models of the Nissan, LADA and Renault brands.

Design

This model is a modernized version of its predecessor – JH3. According to the basic principles, they are very similar - a 2-shaft layout and the presence of synchronizers in all gears. The gearbox is combined with the main gear and differential.

However, there are significant differences:

The clutch is hydraulically driven, whereas the JH3 had a cable clutch. At the same time, with hydraulics, the clutch engages noticeably softer.
In the JR5, gears are engaged using 2 cables (flexible), unlike its predecessor, which uses a rigid rod. This solution reduced vibrations.
The mechanics of the Renault Arcana JR5 are able to handle 200 Nm versus 160 Nm for the previous one.

The markings for this transmission are located on the bottom of the crankcase.

The body itself includes 3 elements:

Gearbox housing;
Clutch housing;
Cover (rear) gearbox housing.

As already mentioned, the design uses a hydraulic clutch drive. In this case, the working cylinder and the clutch release bearing are actuated by one unit, which is fixed to the crankcase with 2 bolts.

An aluminum-based alloy is used to mold the crankcase of the Renault Arcana mechanics and the clutch housing, while the back cover is stamped from steel. Screws are used to secure the clutch housing to the transmission housing. During the assembly process, the joint between the crankcases is coated with a sealant with gasoline and oil resistant characteristics. The rear cover is secured to the gearbox housing using 3 bolts.

The input shaft is a block of drive gears that is in constant mesh with the driven gears at all forward speeds.

The shape of the gears depends on their type:

Reverse gear – straight teeth;
The forward drive is helical.

In this case, the gears of the 1st, 2nd, 3rd and 4th gears of the Renault Arcana mechanics work together with the input shaft, while the 5th speed gear rotates on the shaft (freely). The 5th gear synchronizer is located at the rear end of the input shaft. But the secondary shaft is made hollow inside to supply oil through it under the gears (driven).

On the shaft there are gears (driven) of 1st, 2nd, 3rd and 4th gears with synchronizers. But the V speed gear is on splines on the shaft.

The secondary shaft bearings are different, depending on their location:

Ball - on the side of the lid.
Roller – from the clutch housing side. Below it is an oil sump to ensure oil flow into the shaft.

Resource

The company claims that the Renault Arcana MT resource is 250,000 km. However, if you properly operate the box and change the oil, it can travel more than 400,000 km.

Problems

As a rule, there are very few problems with manual transmissions. As for the complaints from drivers, they relate to not the most precise operation, vibration at idle and current seals.

Features of fifth gear on Largus

Along with the above malfunctions, Largus owners often have a desire to improve the performance of their car, or more precisely, to adapt it to personal requirements. In the main modification, the Lada Largus gearbox comes with a 16-valve engine. The fifth gear ratio (TR) is 0.892. This indicator indicates that the car can move confidently both in city traffic and outside the city. It easily picks up fifth gear from 50 km/h and dynamically reaches its upper speed limit, so there is almost no need to switch to fourth.

However, when driving for a long time at a speed of 90-100 km/h, increased noise occurs and increased fuel consumption is observed. This situation can be corrected by replacing the two fifth gears on the input and output shafts. Replacement takes place with gears that have a lower gear ratio, therefore, fewer teeth. These pairs of gears are sold in aftermarket gear ratios of 0.820, 0.795, 0.756 and 0.738. Experiments on replacing fifth gear gears were carried out by both AvtoVAZ and numerous car enthusiasts.

Gears with a gear ratio of 0.795 slightly change the maneuverability of the Largus. When overtaking, you need to engage fourth gear more often to gain the desired speed. It is often necessary to switch to four when driving on the ground in a loaded car. As for the installation of gears with an IF of 0.756 and 0.738, they aggravate the listed disadvantages.

It is best to replace the factory gears with a pair with a 0.820 ratio.