Why automatic transmission speeds don't turn on | Doesn't change gears - what to do?

03.03.2022 36 227 104 automatic transmission

Author: Ivan Baranov

The automatic transmission, being a rather sensitive unit to improper operation, may periodically work incorrectly, in particular, it may not change gears. In such cases, the car owner has no choice but to take his car to specialists or try to solve the problem on his own. From this material you will learn why the automatic transmission does not change gears, what this may be due to and what to do in such cases.

[Hide]

Gears are difficult to engage with the engine running: possible reasons

At the very beginning, it should be noted that the inability to engage a gear with the engine not running may indicate a serious gearbox malfunction, which consists of failure of the synchronizers. The second reason may be wear or breakage of the gears. It is also possible that the components and mechanisms responsible for transmitting force from the lever in the cabin to the gearbox when selecting a gear may become jammed.

To accurately determine the causes, in the first case it will be necessary to remove the box for disassembly and subsequent troubleshooting; in the second case, it is necessary to identify and replace broken components. In some cases, it is enough to carry out their prevention: removal, lubrication and careful adjustment.

As for problematic switching when the internal combustion engine is running, then the list of the most common faults includes:

  • lack of gear oil in the gearbox;
  • problems with the clutch mechanism;

Recommendations for use

  1. Forget about slipping - you need to eliminate it by any means necessary. Automatic transmissions have a negative attitude towards slipping, especially in snowy and icy conditions.
  2. Always warm up the automatic transmission in winter. With an unheated automatic transmission, the likelihood of certain elements of the unit failing is very high.
  3. Don't use neutral speed in vain. Mode “N” is considered a service mode, so limit its activation.
  4. Cars with automatic transmissions should not be towed by anyone, since such transmissions are simply not designed for this. Loads have a very negative impact on the design of the unit as a whole. If you plan to drive with a trailer, then keep this factor in mind when purchasing a car.
  5. Cars with automatic transmission are not allowed.
  6. Do not tow your car with a rope. While driving, lubricant should always circulate in the transmission, but if the engine is turned off, the TM will not move through the system. Of course, this negatively affects the operation of the unit as a whole.
  7. Always use only high-quality transmission fluid recommended by your vehicle manufacturer. Remember that using a cheaper lubricant over time can only harm the unit of your car, if not kill it.

Causes of machine failure

The following are the main causes of automatic transmission failure:

  • resource consumption or wear of parts. The most banal, but at the same time the most common reason. Even neat and careful owners sooner or later come to this situation;
  • using low-quality or unsuitable oil. Another common mistake. In pursuit of savings, drivers use uncertified oils. This causes rapid breakdown of the automatic transmission;
  • service with low-quality consumables. Here again the savings may be deliberate;
  • inexperienced or irresponsible mechanic. You will never guess how decently a person will approach working with a car. Try to contact trusted specialists;
  • machine use habits. Many habits lead to wear and tear on parts. A clear example is frequent aggressive driving. But the problems are not limited solely to governance. Warming up the car for a short time in the cold also leads to malfunctions.

Thus, most of the reasons depend on the car owner himself. If something remains unclear to you, please refer to the vehicle manual or the appropriate service center. There you will learn the nuances of operating your car brand and protect the automatic transmission mechanism from breakdowns.

What are the types of automatic transmission malfunctions?

It is difficult to imagine the modern world without a car with an automatic transmission. Frequent traffic jams and traffic lights at every intersection made the automatic machine an indispensable thing for moving around cities. Perhaps this is why most significant concerns are gradually abandoning mechanics in favor of automatic gear shifting. This trend is gradually coming to our country, and with it the problems associated with automatic transmissions.

Any current design in a car has two operating principles: mechanical and electronic. Automatic transmission is no exception. Physical gear shifting is carried out by mechanisms, and algorithms are calculated by the software component. Therefore, all causes of failure are divided into two large groups:

  • mechanical breakdowns. They occur in the hydraulics and physical drives of the gearbox;
  • electronic system failures. Malfunctions of programs or electrical parts of the machine.

Let's look at each of these points separately.

Mechanical and hydraulic problems

Most often, due to mechanical failures, the following elements break:

  • wear of the shafts or gears of the mechanism;
  • damage or wear of clutches, discs, brakes inside the transmission;
  • problems in the operation of the torque converter;
  • wear of the hydraulic unit;
  • clogging of the oil channels of the box;
  • oil pump failure.

From the above list, you can see that the main problems in the mechanical part begin when parts wear out or the use of unsuitable oil. It is worth noting that this is a real stumbling block for automatic transmissions: more often than not, car enthusiasts simply run out of service life of the internal structures of the box. This once again proves the security of this type of transmission.

It is very important to detect and correct automatic transmission problems early . Otherwise, one malfunction will give rise to another, forming a kind of mutual responsibility. So, when the clutch wears out, the oil transmission channels become clogged, and these will lead to problems with the pumping system. Having procrastinated with one problem, some motorists come to services with an almost completely destroyed machine gun. But we'll talk about the reasons a little later.

Electronics and possible problems

Automatic transmission malfunctions do not bypass the electronic internals. We list common examples of broken elements:

  • breakdown of electronic components, automatic transmission controller;
  • incorrect operation or broken transmission sensors;
  • faulty or worn electrical wiring;
  • short circuits;
  • malfunction of machines, phase devices.

The automatic transmission is designed in such a way that even if the electronic control fails, the car can continue to move. In this case, backup program algorithms are launched: the transmission goes into emergency mode. More often the car automatically switches to 3rd speed. This helps the driver get to the nearest service station and eliminate the cause. Modern systems notify the owner about problems in the electronics.

You can often hear from fans of manual transmissions that if the electrical component breaks down in a car with an automatic transmission, then, unlike a manual transmission, driving it is impossible. As we can see from the example above, this judgment is not true.

Signs of a torque converter malfunction

  1. A metallic sound is heard when shifting gears. As the speed increases and load is applied, the sound disappears. This indicates a problem with the bearings. It is necessary to disassemble the torque converter and assess their condition.
  2. In the speed range of 60-90 km per hour, slight vibration is observed. Over time, its value increases. This is caused by the filter becoming clogged with wear products. In this case, you need to replace the oil filter and oil. Usually it is necessary to change the oil in the gearbox and engine.
  3. Problems with dynamics indicate a faulty overrunning clutch. It is necessary to disassemble the torque converter and replace the broken clutch.
  4. The car has stopped and it is impossible to continue driving. This indicates a broken spline on the turbine wheel. Repair of the unit consists of replacing the turbine wheel.
  5. The occurrence of a rustling noise while the engine is running indicates a malfunction of the bearings located between the torque converter cover and the turbine wheel. The rustling noise may disappear while driving. In this case, you need to contact a car repair shop and carry out repairs. Thrust needle bearings are usually replaced.
  6. A metallic knock is heard when changing speed. This indicates deformation of the shoulder blades. Repair is carried out by replacing the faulty wheel.
  7. It is necessary to periodically monitor the condition of the oil in the automatic transmission and torque converter. If aluminum powder appears on the dipstick, you need to check the freewheel, which is made of an aluminum alloy. Most often, the appearance of this powder indicates wear of the end washer.
  8. With the engine running and standing, there may be a smell of melted plastic near the automatic transmission. This occurs due to overheating of the torque converter and melting of the polymer parts of the assembly. Overheating occurs for a variety of reasons, but is usually due to lubrication. When the oil level decreases, signs of oil starvation of the torque converter and gearbox appear. There may be problems with automatic transmission cooling. In this case, the repair consists of changing the oil and checking the cooling.
  9. When switching speeds or changing the operating mode of the box, the motor may stall. This indicates a breakdown of the automatic control system that blocks the action of the torque converter. The repair consists of replacing the control unit.

There are no definite signs of a torque converter failure, so technicians sometimes cannot immediately determine the cause of the failure. This leads to increased repair costs and vehicle downtime. If such problems arise with the automatic transmission, the driver needs to contact a car service center as quickly as possible.

Malfunctions of an automatic transmission can be detected in the fact that it is impossible to switch operating modes of the transmission or it is blocked in any gear. In this case, the driver is required to transport the car using a tow truck. Driving independently in a car with a faulty gearbox is prohibited, as this will lead to serious damage to the drive and the entire transmission.

We recommend: DIY car muffler repair without welding

Sometimes a fault can be detected using sensors built inside the box. Such sensors signal a lack of oil pressure, overheating or malfunctions in the gearbox drive. Many signals about malfunctions with the box are vague, and in this case it is not possible to find out an accurate diagnosis even when using computer equipment. A specialist needs to inspect the transmission, remove the box and, after disassembling it, determine the fault.

Automatic transmission does not shift gears - troubleshooting

A fairly serious breakdown in cars occurs when the automatic transmission cannot shift to a higher gear. There can be a lot of reasons for this, because the automatic transmission is connected to the entire engine and electronics of the car. Most often, the reason that the automatic transmission does not shift gears is its freezing.

If suddenly in winter a car with an automatic transmission does not shift gears, then perhaps the oil in it has simply frozen from the cold. This problem is dealt with in different ways; the greatest results are achieved by insulating the automatic transmission and engine. You also need to change the oil in the automatic transmission, filling it with one that is suitable for the climatic conditions.

Automatic transmissions are also completely different in design, but are most often used with a torque converter. In such a system, the connection between the engine and the wheels is ensured by oil pressure. The quality of operation of such an automatic transmission directly depends on the quality of the oil in it.

Gear shifting problems

The design of automatic transmissions is quite complex; they are all hung with sensors, just like the injection engine itself. If at least one of these sensors fails, then it is quite possible that the automatic transmission will stop shifting gears. It often happens that due to shaking and an aggressive environment, wires from sensors fall off or poor contact is formed.

Another reason that the automatic transmission does not want to change gears may be clogged oil filters or low oil level. In this case, the filters are changed and new oil is added. Also, automatic transmission malfunctions can be diagnosed based on error codes.

Automatic transmission care

In order for the automatic transmission to work faithfully for many years, it must be properly cared for. This is a rather delicate device in a car; the automatic transmission is very afraid of overheating and poor quality oil. In any automatic transmission you need to change the oil from time to time, generally this should be done no later than after 50,000 km, it all depends on the type of fluid.

In addition, the fluid needs to be renewed every 15,000, draining some of the old and adding new.

When a complete oil change occurs in an automatic transmission, the filters must also be changed. It would be a good idea to replace the sensors, because the failure of any of them leads to problems with the automatic transmission.

After filling in fresh oil, do not forget to check it before the next run. The condition of the oil should be monitored regularly by examining its color. In addition, if the oil level is too low, the automatic transmission will quickly fail.

The automatic transmission is also afraid of wheel slipping, so you should not skid for a long time on a slippery surface; it is best to push the car from the outside.

If it turns out that the automatic transmission malfunctions or does not change gears at all, then the car should be sent to a service center for repairs. As for self-repair, you can only try changing sensors, filters and oil. If you have no experience in automatic transmission repair, it is better to entrust this matter to specialists.

Source: https://tuningui.com/akpp-ne-pereklyuchaet-peredachi/

Why don't the gears turn on when the engine is running?

Gears may not engage or may not engage fully if the fault is related to the clutch basket. The release bearing may also be the cause. If the specified bearing does not move freely along the input shaft or is jammed, then replacement of the part is necessary.

We recommend reading: How to apply for an old-age social pension

The clarity of gear engagement and the operation of the entire shift mechanism often worries owners of cars with a manual transmission. A common problem is that after starting the engine, one or more gears are engaged with great effort or not completely, it is not possible to change gears, at the moment of switching on, extraneous noise is heard, unnecessary vibrations appear, etc.

Diagnostics

Automatic transmission is popular today both in the domestic car market and in the foreign one. It has more than enough advantages, so it is not surprising that it is so popular. However, like any mechanism, it has the ability to break down. Most often you hear among car owners: the gearbox cannot change gears, you have to do it manually. We will talk about possible causes of failure and their diagnosis further.

First of all, before starting work, you should make sure that the problem is in the automatic transmission. That is, do all other car systems work properly if the engine cannot change gears. There are many problems that lead to a drop in the oil level in the gearbox. The main problem here is a violation of the tightness of the front automatic transmission oil seal.

Reasons for the drop in oil level in the automatic transmission:

  1. Oil leakage: through the crankshaft seals, through the cylinder block gasket, through the oil filter gasket, through the oil seals. The root of the first problem lies in the wear of the sealing edges of the crankshaft oil seals. This happens either due to the addition of low-quality auto chemicals or low-quality oil. The second problem may be due to overheating of the engine or due to improper tightening of the power bolts when assembling the engine. The most typical cause of the third problem is the rubber sealing ring not being retained in its cage. The fourth problem arises due to overheating of the rubber caps.
  2. Piston ring problems: wear, overheating, coking. Piston ring wear is a common problem because it always occurs. And, as a rule, this wear begins in areas most exposed to pressure.
  3. Overheating of oil scraper rings occurs at temperatures above 2000. Any increase in temperature threatens failure of the piston rings. This, in turn, affects the level of oil absorption by the engine.
  4. Coking of piston rings occurs due to the use of low-quality oil. After all, you must admit that the rings are in good order only when they are movable. Their stagnation negatively affects engine performance.

In addition to these reasons, there are many other reasons for malfunctions of 4 and 5-speed gearboxes.

Automatic transmission malfunctionCause
After overcoming the rise, the car can switch to a lower gear ahead of time.Low gearbox oil level, worn discs or o-rings
Reverse speed is fine, but the car does not move forward, but skids in place.Wear of forward clutch discs, clogged gear shift valve, damage to oil rings
Shifting forward is normal, moving backward does not occur.Problems in the operation of the brake band (it is either worn out, torn, or its piston rod is broken), malfunctions of the braking package
When the lever is set to neutral, the car moves forward or backward.The drive cable or lever is not adjusted correctly, the clutch discs or plates are touching
The car moves when the gear shift lever is in the “N” position.Damage to the adjustment of the cable or lever of the automatic transmission control drive, interruptions in the operation of the clutch piston, welding of friction discs to steel
Aluminum grains at the bottom of the pan Wear of either the working layer of the sliding bearing, or the aluminum washer, housing, etc.

Of course, these are not all the reasons for breakdowns of the automatic transmission itself, but they are the most common. In addition to these, there are also malfunctions of the electronic transmission system. Diagnosis of such problems does not require mechanical intervention in the car; they are detected using a scanner.

The main symptom of a malfunction of the electronic automatic transmission system: the gearbox is in a dead emergency mode, the automatic transmission does not shift.

This indicator refers to problems with malfunction of the engine control unit, malfunction of air flow sensors, malfunction of the gear shift position sensor, etc.

Friction disc wear

When changing gear into an automatic transmission from reverse gear, the car begins to slip. The reasons for the machine's behavior are hidden in:

  • displacement or deformation of friction discs;
  • rupture of rings or couplings;
  • valve sticking.

Disc wear can also affect the performance of the transmission. For example, it is impossible to switch to reverse gear, while at the same time moving forward is only possible in second. The reason for this behavior of the car lies in the wear of components; rubber parts are easily worn out when driving. If, during visual diagnostics, all of the specified parts are intact, then further attention should be paid to the clutch drum; perhaps the reason lies there.

You won't be able to drive a car when it's cold. If, when warming up, the car slips at forward and reverse speeds, then you should pay attention to the properties of the oil used, and if possible, it should be replaced. In addition, there may be another reason for this behavior of the car - a clogged filter.

When starting to move, the car slips in place, the movement itself continues, the speed switches perfectly. This may also indicate wear on the friction discs. In this situation, attention should be paid, among other things, to the condition of the torque converter (hub wear is possible) and to the piston cuffs.

Low gearbox oil level

An insufficient amount of oil in the box makes the process of shifting gears extremely difficult, but the speeds must be engaged. When switching in this way, a metallic crunch is heard, and when driving in a gear, the transmission begins to make a lot of noise and “howl.”

A complete lack of lubrication in the gearbox will not allow you to change gears, since without oil the synchronizers will not be able to work properly, and the gears in the gearbox will not engage.

Any manifestation of these symptoms requires immediate cessation of operation of the vehicle and checking the transmission oil level in the gearbox. It is also necessary to inspect the gearbox for damage to the housing, oil leaks through the seals and gaskets.

It should be noted that for manual transmissions of many cars, the oil in the gearbox is filled from the factory for the entire service life. In practice, replacement is recommended every 60-80 km. mileage

Automatic transmission kicks: what to do

Possible problems with an automatic transmission can take the car owner by surprise, the most common problem is the automatic transmission kicking, what to do in this case?

How to resolve an unpleasant situation without an emergency visit to a service station? It's better to know about this in advance.

Why does the automatic transmission kick when shifting?

An automatic transmission is a complex mechanism that switches speeds depending on the load on the car's engine.

There is no clutch in the presence of such a transmission; you do not need to change gears yourself. Automation is responsible for everything.

When driving, the driver pays attention only to comfort, and when problems begin with the transmission, the car owner tries to look for answers at a service station, where they quote a round sum for diagnostics and repairs.

Self-diagnosis

Before contacting the service, you can try to independently identify malfunctions in the automatic transmission.

Knowing in advance the approximate condition of the box, there is a chance not to be deceived by the service station workers.

So, why does the automatic transmission kick when shifting:

  1. Kicks are observed when the car is put into reverse. The cause of this phenomenon may be a breakdown of the torque converter, or problems in the operation of the sensor. But a more accurate “diagnosis” will be announced by a specialist after computer diagnostics.
  2. When you turn on the “Drive” mode on a hot engine, jolts are noted. Most likely, the reason is in the hydraulic plate, which is broken. Repair work in this case will require considerable investment.
  3. Kicks are noticeable when braking. The problem probably lies in the clutches and valve body. The solution to the problem will be to completely disassemble the box with associated significant costs, since many elements will be replaced.
  4. Shocks during braking may also indicate that the software that regulates the operation of the box is outdated.
    By “reflashing” the software, you can get rid of both kicks and excessive fuel consumption, ensuring a smooth ride of the car. It is better to entrust such important work to specialists, in order to avoid aggravation of the situation or complete unsuitability of the box.
  5. The automatic transmission jerks the car when the gear is engaged. The reason for the shocks can be quite trivial - you just need to change the oil in the box or replace the transmission filters.
  6. The solution to the problem of kicks when shifting gears can be timely noticed deviations in the operation of the lowering resistor (resistance) of the box.
    It is through this resistor that the pressure control signal is supplied for smooth switching. If this resistor fails, the driver feels pronounced kicks.
  7. A clogged line pressure valve can cause the transmission to kick around.
  8. Poor quality fuel can also affect the ride quality of your car. Buying gasoline at an unfamiliar gas station can lead to kicks in the transmission.
  9. An insufficiently warmed car can also cause a “jerky” automatic transmission. Unheated oil inside the box does not provide good grip and leads to kicking.

Timely identification of a problem with the box can prevent its final breakdown and subsequent expensive repairs.

In different diagnosed cases, actions with automatic transmission will differ. Some repairs can be done independently, while others can only be done with the help of specialists from the service center.

When an automatic transmission kicks, what should you do? If the automatic transmission needs an oil change, then you can do it yourself; it will be more difficult (but possible) to change the filters in the transmission.

It will also be within the power of the car owner to independently diagnose the step-down resistor.

To do this, you need to find it in your car (under the air filter housing). Visually inspect its condition.

If the wires are found to be moving away from the plug, they must be immediately reattached.

Next, measure the resistance with an ohmmeter. Depending on the make of the car and the gearbox, it should be equal to a value in the range from 11 to 13 Ohms.

If the resistor showed values ​​much lower/higher or did not show them at all, then it definitely needs to be replaced.

Knowing about the problem and contacting a service station with it, you can save a lot. Usually, specialists like to “exaggerate” in such diagnostics and add extra to the amount for repairs.

If the automatic transmission jerks when switching, then the reasons (as stated above) may be outdated software.

In this case, it is possible to accurately diagnose the problem only in a car service; solving the problem on your own is almost impossible without special equipment.

If the line pressure valve is possibly clogged, the gearbox must be disassembled to gain access to it.

Cleaning is easy and does not take much time. In order to prevent various kicks and jolts of the automatic transmission, it is necessary to monitor the mileage of the car.

Every 100,000 - 125,000 km, it is better to diagnose the machine. Moreover, the oil will have to be changed during such periods.

Diagnostics

Shifting the automatic transmission lever

Automatic transmissions have already become popular among domestic motorists, although twenty years ago no one could have thought that this would happen. As a result of many advantages, the demand for these units is constantly growing. Of course, like any other component in a car, an automatic transmission can periodically fail or function incorrectly. In fact, there can be many problems with the unit, but if the automatic transmission does not change speeds, then the only way out is diagnostics.

But, first of all, you need to reliably make sure that this malfunction is really related to the operation of the unit. You must ensure that all vehicle systems are functioning properly if you are unable to change gears. In principle, one of the main faults due to which the automatic transmission does not change gears is often a lack of working fluid in the system. As a rule, this is usually due to a worn out oil seal of the unit, which causes fluid to leave the automatic transmission.

We recommend: What is an engine knock sensor

A lack of lubricant level in the box may be due to the following factors:

  1. Liquid leak. Oil can escape through the crankshaft seals, the cylinder head gasket, the oil filter seal, or through the oil reflective caps. If transmission oil (hereinafter referred to as TM) escapes through the seals, this indicates their wear, which can be caused by the use of chemicals or poor-quality lubricants. The cylinder block gasket could wear out due to overheating of the engine or incorrect tightening of the screws during disassembly and reassembly of the engine. If the problem is with the oil filter, then most likely it is due to the fact that the sealing rubber cannot stay in place. If oil leaks from the automatic transmission due to the reflective caps, then the problem is their wear caused by overheating.
  2. Breakdown of the vacuum corrector. Inside this device there is a special membrane that reacts to the level of vacuum in the collector. If the integrity of this element is violated, then the TM will get into the car engine. In this case, the unit can function for a long time even with a significantly reduced level of lubrication, but over time it will simply fail.
  3. If the TM goes into the cooling system. If the tightness of the oil cooler is broken, then the lubricant will go into the engine radiator, since the oil pressure in the automatic transmission radiator is always higher than the pressure in the cooling system. And when the engine turns off, the process of lubricant leakage into the coolant begins. As a result, an emulsion begins to appear in both the internal combustion engine and the automatic transmission. When antifreeze gets into an automatic transmission, it corrodes the clutches, as a result of which corrosion begins to form on the latter. In the event that gears have not been changed for a long time, the problem can be solved by replacing the oil cooler. It is also a good idea to rinse the automatic transmission with working fluid. Having done this, you can try to bring the unit back to life.
  4. If the pipe that connects the automatic transmission to the oil cooler breaks. In this case, all the lubricant will come out of the transmission in a matter of minutes, so the unit will simply stop working.

Automatic transmission disassembled

This is only a small part of the reasons why an automatic transmission may not shift gears. A more complete list is presented in the table.

CausesBreakdowns
The need to replace clutches, a broken piston cuff, failure of the clutch rings, or a stuck valve body.In this case, a car with an automatic transmission will only be able to drive in reverse; forward gears will not engage.
Breakage of clutches, piston cups, wear of o-rings, malfunction of the spline connection of the clutch drum or other failure associated with this unit.In this case, the automatic transmission cannot change gears back, but the first and second gears, unlike the others, will work.
Malfunction of the cuff, piston rod of the brake band or its wear, problems in the operation of the braking package.The car does not go backwards, all forward speeds engage normally.
Failure of the torque converter, breakage of the oil pump gear, lack of lubrication in the system, clogged filter, wear of the clutches, breakage of the cuff, sticking of the valve.In this case, the vehicle will not be able to move either forward or backward. When trying to switch to any mode, the driver will not feel a characteristic push.
Failure of the torque converter, lack of lubrication in the system, clogged filter element.The speeds don't change at all. When the parking mode or neutral speed is activated, a characteristic push to engage the gear will appear, but the car will not move.
Valve stuck in the valve body.The car can go backwards or only in first and second speed. Other transmissions will not be included.
The turbine wheel hub splines and friction clutches are worn out, and the clutch seals are out of order.In this case, the car will slip when starting to move, but then the gears will engage well.
The pistons of one of the clutches are jammed, the adjustment of the automatic control cable has been disrupted, and the clutches have become welded to other discs as a result of prolonged slipping.The car can only be driven at neutral speed.
Incorrect adjustment of the throttle valve cable, the filter element is clogged, the throttle valve or centrifugal regulator valve is stuck.In this case, gear shifting will be carried out at increased speeds, significantly higher than standard values.
The clutches of the automatic transmission have worn out, and excessively large gaps have appeared in the packages.With such a breakdown, switching on a particular speed will be accompanied by shocks. In normal mode, the driver would feel the shocks.
During long-term operation, the splines of the turbine wheel were cut off.The car cannot go forward or backward. In this case, the pressure in the transmission line will be normal.
The oil pump pulley splines are worn. Also in this case, the splines on the reactor pulley may be worn out. The car will not be able to drive forward or backward, but there will be no pressure in the line.
Failure of clutches. When the clutches wear out, the transmission fluid will contain more metal dust and chips from the discs. As a result, dust clogs the filter element, and the pressure in the line begins to decrease. The vehicle will operate normally until the lubricant warms up. After warming up, the car will begin to slip and the car will not be able to move at all, neither forward nor backward.
In the design of the automatic transmission, one or more gear clutch valves have become stuck or the torque converter is not functioning correctly as a result of the turbo wheel being jammed.In this case, changing gears will be completely impossible. When any mode is activated, the car will immediately stall, the driver will not even have time to press the gas pedal.
Moisture somehow gets into the structure of the unit. As a result, foam begins to appear inside the automatic transmission, and the oil pump will stop creating pressure. The gears may change normally for a while, but the car will slip. Visually assessing the oil, you will see that it has foamed and turned light brown.

Problems associated with a lack of transmission fluid

1. When you move the shift lever to any of the positions, a push is felt, but the car does not move either forward or backward. A low oil level can occur due to leaks, a faulty torque converter, or a dirty oil filter. Treatment methods are obvious: replace, fix, clean. And be sure to add fluid to the level.

2. On an automatic transmission, gear shifting in the highest mode during a long climb causes slippage and a premature transition to a lower gear. This occurs because insufficient fluid level reduces hydraulic forces. The cause may also be wear of the clutch discs, wear of the cuffs or o-rings. Replacement and topping up help solve the problem.

Troubleshooting methods

We looked at the causes and signs of machine malfunctions. Now it’s worth saying a few words about repairs. Let’s say right away that there are two methods for solving transmission problems:

  1. Self-repair or prevention.
  2. Contacting specialists.

Needless to say, the first option is cheaper and preferable for every car enthusiast. However, in reality, not all operational problems can be solved with your own hands. For example, if the automatic transmission does not change gears or slips, then only a qualified specialist will assist the car.

Let's select specific examples for both situations.

Independent solution

We present a number of correctable errors in the appropriate form: general cause – possible problems – ways to eliminate them.

1. Misalignment or malfunction of the gear shift component:

  • the car moves in gearbox mode P;
  • The speed letter on the panel does not match the set one.

Remedy: Diagnosis and replacement of the faulty part; you can repair it yourself according to the instructions provided.

We recommend: How to break in an engine after a major overhaul

2. Oil leakage from the automatic transmission. Common problem with the box:

  • the fastenings of the mechanisms inside the transmission come off on their own;
  • destruction or unsuitability of oil seals and gaskets.

DIY repair methods:

  • tightening bolts, purchasing and installing new seal rings;
  • lowering the oil level in the automatic transmission.

3. Noise or uncharacteristic sounds when the box is operating:

  • the car changes gears itself;
  • switching positions occurs with great difficulty;
  • The car does not respond to switching and does not move.

Remedy: Measure the oil level and add the required amount.

Only the main cases of minor breakdowns inside the automatic transmission are given. If your situation fits at least one of the points, read the instructions for the car. Inside you will find step-by-step steps to solve the problem. In the future, it is recommended to turn to professionals.

Repair in service

We will describe the problems that require contacting a qualified workshop.

1. The car remains in place during any action with the gearbox mechanism. There is no reaction or the slightest movement.

Causes:

  • little oil in the system;
  • valves or rings are clogged;
  • hydraulic system malfunction;
  • filter failure;
  • Main gear malfunction or wear.

2. Shocks and impacts when changing gears.

Causes:

  • coupling wear;
  • hydraulic unit valve malfunction;
  • Valve spring damage.

3. Unhealthy noise in the differential area of ​​the car

Causes:

  • bearing or gear wear;
  • some mechanisms jam or become loose.

Many problems are more often identified at the stage of disassembling the transmission. Thus, a trip to the service center is a priority for a working car.

Actions of motorists

I’m moving on to the most anticipated part - if you are not able to figure out on your own why the gear shift on your gearbox does not engage, then you should contact a car service center, where specialists will carry out diagnostics and educate you about the breakdown, cost and repair time. Checking the functionality of automatic gearboxes is carried out only using computer diagnostics, so you should make sure that the service is available at the car service center.

If after diagnostics no faults are found, and the car continues to act up when changing gears, then you should pay attention to the speed sensors, wiring and scenes.

The backstage can be cleaned quite easily using a hole in the garage or an overpass. The gear and speed sensor is a rather capricious thing. If there is a breakdown, the sensor stops sending signals, which forces the gearbox not to respond to the signals (the gearbox simply sees that there were no signals).

If all the presented methods for eliminating the breakdown are not effective, then the car requires the intervention of a car service guru.

It is worth understanding that there are many more causes of failure, symptoms and methods for eliminating them. You should not delay resolving the issue and allow your car to “cure.”

The box has a rather complex structure, and it is impossible to answer this question right away. But based on some indirect signs, you can determine the essence of the problem and try to fix it yourself.

Causes

Before getting acquainted with methods for eliminating breakdowns, it is necessary to consider their main causes.

Lever link

In old automatic transmissions, where the selector is mechanically connected to the transmission, the gearbox lever often breaks, making it impossible to switch the operating mode. In this case, the repair consists of replacing the faulty selector and rocker. Such malfunctions are detected by difficult movement of the automatic transmission selector. As a result, the lever does not move and the transmission must be repaired. Some brands of automatic transmissions cannot be repaired without removing them from the car, making repairs easier.

Oil leak

A popular problem with automatic transmissions is oil leaks at the seals. Therefore, it is advisable for the car owner to periodically visually inspect the box on a pit or lift. If you detect oil leaks on the gearbox, you need to contact a car repair shop. In this case, the problem is solved by simply replacing the gaskets and gear lubricant.

Control block

Electronic components can break down for various reasons. Sometimes there are problems with the functioning of the automatic transmission control unit. The unit may incorrectly select the speed for the gears, or it itself blocks the operation of the transmission. Troubleshooting the operation of this unit, as well as the electrical circuit of the box, consists of replacing control cables and faulty units.

You need to know that driving a car with a faulty unit is dangerous, so it is recommended to contact a workshop at the first sign. And if the automatic transmission does not want to work at all, then you should not start the engine, but it is better to move it to a service center using a tow truck. The causes of ECU failure may be:

  • Exposure to moisture.
  • Heat.
  • Effect of vibration loads.
  • Mechanical impact.
  • Sudden voltage drop.

These reasons can lead to damage to the control unit, which requires expensive repairs or replacement. Car service centers can tell you how to check the electronic unit of an automatic transmission. Fault diagnosis is carried out using special instruments that allow us to identify the nature of the fault, which makes it possible to eliminate it at the lowest cost. In many cases, ECU repair comes down to replacing burnt out chips and boards. This work is quite complicated, since it requires desoldering microcircuits from boards and replacing failed capacitors. Sometimes it is easier to replace a faulty unit with a new one. This makes it possible to get rid of problems with the automatic transmission.

Qualified repairs should be carried out only in a certified center that has sufficient experience in automatic transmission repair. There is no need to skimp on qualified repairs and turn to garage technicians.

Valve unit malfunctions

One of the important components of an automatic transmission is the valve body, which is responsible for the gear shift process. This unit, according to the masters, is the brains of the automatic transmission. The valve body plays the role of organizer of the movement of transmission oil through the box. There are different hydraulic block designs, depending on the type of box.

During operation, the valve body takes on heavy loads, so if it is poorly maintained or used incorrectly, the valve body may break. Malfunctions of the automatic transmission valve body may occur due to improper operation of the transmission. For example, in cold weather, a driver can not wait for the oil in the box to warm up, but immediately start driving with heavy loads. In some cases, there are problems with the cooling system that arise due to infrequent oil changes and improper operation of the oil receiver. This can lead to malfunctions of the valve body and the entire box.

Failures can be determined by various signs of the valve body. You need to know that despite the progression of computer diagnostics of machines, it is difficult to determine the malfunction of this unit. Therefore, during maintenance, specialists can accurately diagnose only by removing the box from the car.

Torque converter malfunction

This mechanism is an element of the automatic transmission. It makes it possible to create smooth gear shifts for the gearbox. Its design is constantly being modernized and complicated. Now the torque converter on an automatic transmission works as a clutch. When changing gears, this unit disconnects the engine from the gearbox. After engaging the gear, it takes over the torque, which ensures the smoothest speed change.

If problems arise with this unit, only repair it is necessary. In general, these works cost less compared to the electronic unit and valve body. Torque converter malfunctions are identified by the symptoms we indicated above.

How it works

Both manual and automatic transmissions have a complex design. For their correct functioning, the coordinated work of a large number of parts is required. Of course, an automatic transmission is more complex, but the problem may not be related to the transmission. For example, if you cannot move the automatic transmission selector out of P, there is a possibility that the brake pedal switch is faulty.

In the case of a manual transmission, the gear shifting process depends on the health of the clutch pedal, the clutch itself and other parts. You press the pedal, which engages the clutch release mechanism, and separates the engine and transmission. This allows you to change gears. Synchronizers facilitate smooth engagement of all gears.

In addition, failure of the master cylinder is possible (on some cars the clutch is electronically controlled, on others the system has a hydraulic drive, in which proper operation of the master and slave cylinders filled with liquid is required to change gears). In this case, the car will behave as if the clutch pedal is not pressed.

The automatic transmission does all the work for you. All you have to do is press the gas pedal, and the transmission itself will change gears as the speed increases. This requires many additional parts that are not found in a manual transmission.

The most common causes of these malfunctions are discussed below.

1. Low level of working fluid Both types of transmission require different types of working fluid for normal operation. If its level is insufficient, then there is a possibility that you will not be able to change gears, especially in the case of an automatic transmission. In this case, transmission parts receive significant damage. Even if you can get into gear, the transmission may not be able to move the vehicle.

2. Master Cylinder Fluid Level Low If your vehicle has a hydraulic clutch, the first thing you should check is the fluid level in the master cylinder. Typically, a lack of fluid is associated with a leak in the system (you may find a puddle of fluid under the clutch pedal).

3. Broken clutch cable If the clutch on your car is controlled by a cable, it may have broken. If the clutch does not disengage when you press the pedal, this may be one of the main causes of the malfunction.

4. Malfunctioning brake light switch If you cannot move the automatic transmission selector out of P, the most likely culprit is the brake light switch. It is located under the brake pedal and is designed to activate the shift lock solenoid if the brake lights are not working.

5. Failure of synchronizers If you can engage the gear, but still hear a grinding noise, most likely, the transmission synchronizers have failed. In this case, switching to the next gear should occur without problems.

How to Troubleshoot A mechanic should confirm that the gears are not shifting. This may require a test drive (if the shift does not occur while driving). The mechanic can also read trouble codes stored in the electronic control units through the OBD II connector located under the instrument panel.

Why is it difficult for the gear lever to shift on a manual transmission?

  • After the desired shift has occurred, you need to release the clutch pedal, there is no need to hold it! Because there is increased wear on the clutch disc
  • It is advisable to move in the gear that corresponds to a given speed, this relieves both the engine and the gearbox from unnecessary loads, the best is 4th gear, also called “direct”, in this connection the minimum number of gears and all two shafts are occupied (in bypassing the intermediate). This reduces wear on the manual transmission
  • A lower gear should be engaged when the speed decreases, just like an upshift when accelerating.

The main causes of malfunctions Mechanics, like automatic ones, are designed to transmit and change torque from the power unit to the wheels, and this must be done comfortably and dynamically. That is, the car must accelerate as quickly as possible and do this without any “jerks” of prohibitive engine speeds (so that it does not “growl like a victim”) and, if possible, have sufficient traction forces.

Rating
( 2 ratings, average 4.5 out of 5 )
Did you like the article? Share with friends:
For any suggestions regarding the site: [email protected]
Для любых предложений по сайту: [email protected]