Sometimes unforeseen situations happen in life and any driver can be left without the keys to their car. And such incidents most often occur in nature or in the country. And in order to get to a car service center to replace all the car’s locks, you will first have to start it without a key.
Many modern cars are designed in such a way that they cannot be started without a key. They are equipped with numerous protective mechanisms that can block the steering wheel and starter. Computer chips in the ignition switch will also prevent you from using the vehicle without a key.
Most modern cars cannot be started without a key.
Even knowing how to start a car without a key, only those who own cars produced in the 80s and 90s, and in particular the VAZ 2106 or other models of this automaker, will be able to take advantage of this opportunity.
How to start a car without a key
The most common reason is the loss of a key; it often falls off the ring on the keychain, gets lost on its own or along with a purse, handbag, and so on.
Another reason is the key breaking right in the ignition switch. And another common reason is that the ignition does not turn on when you turn the key.
As for starting the car in the third case, everyone knows what to do. We must try to start the car using a pushrod. Unless, of course, the reason is a dead battery or a fault in the starter.
To check, you need to see if there is a spark, and if there is, try to push the car. It is difficult to do this alone, but if you ask for help, you can easily start the car from the pushrod.
To do this, first set the speed switch to neutral, and after acceleration, turn the ignition key, press the clutch, engage the second speed and release the clutch. As a rule, the car starts quickly.
If you don't have the ignition key, there are several ways. It is advisable to have a small flathead screwdriver in the car just in case. Use a screwdriver to unscrew that part of the panel that blocks access to the ignition switch.
All fasteners connecting the ignition switch and steering are removed. Uncoupling will unlock the steering wheel, this is the very first step - unlocking the steering wheel. Then the screws connecting the two parts of the ignition switch - mechanical and electrical - are unscrewed.
Attention! You just need to unscrew the screws, do not separate anything. After these simple procedures, the screwdriver is inserted into the hole intended for the ignition key and turned in the same direction in which the key is usually turned
After this the car should start
After these simple procedures, the screwdriver is inserted into the hole intended for the ignition key and turned in the same direction in which the key is usually turned. After this, the car should start.
Replacing the ignition switch and its contact group
But how can you start a car without a key if you don’t have a suitable screwdriver at hand?
Everyone has probably seen more than once how dashing car thieves and tough guys instantly start a car by connecting two wires to each other.
In fact, everything is not so simple and such manipulations can be done by very professional people who know EVERYTHING about car electricians.
You need to know which wires to connect to each other. As a rule, the best assistant here is the simplest multitester, which, like a screwdriver, is recommended to have in every car. But this is in theory; in practice, almost no one has it.
But if you still have a multitester, then everything is really simple. Having repeated all the steps described above, starting with removing the casing under the steering column and freeing the wiring going to the ignition switch, you must first find the ground and insulate it.
By the way, perhaps there is a small light bulb nearby; it will also show which wire is “ground”. If there is neither a light bulb nor a tester, you can guess by the color of the wire; the grounding wire is usually black or green.
The remaining live wires can be shorted one by one to ground, but only for the shortest possible time so as not to burn the wiring. If you have a multitester or a light bulb, it will not be difficult to identify all of them simply by connecting them through the device one by one to ground.
All live wires must be carefully collected into a bundle and ensure that they do not shorten onto the housing. The third will be the starter wire. It's easy to find, but first of all you need to put the car on the handbrake and neutral.
Alternately, the remaining free wires must be connected to the live group. Which will turn on the starter. that's the one you need.
How to unlock the steering wheel of a VAZ 2107 without a key
Next, all that remains is to connect these wires, and the car will start. After this, disconnect the starter wire from the first two groups and insulate it if possible. To stop the engine then it is enough to open the “ground” and “voltage”.
As a one-time measure, these methods can be used, but it should be remembered that electrical wiring is quite dangerous to use without insulation.
Due to inexperience or carelessness, you can ruin all the wiring. It is best to have a second key hidden in the car just in case and not take it to extremes.
All options are acceptable only for those who are confident in their abilities and knowledge. It is advisable to have a duty kit in your car, consisting of a multitester, a small flashlight bulb, insulating tape, a set of candles and a spare belt.
Method 1.
The first thing you need to do is remove the casing that covers the steering column. This gives you direct access to the ignition switch. Now the main thing is to correctly determine the location of the wires. To do this, you can use a multimeter. Remember, we need to find exactly the grounding. Therefore, one of the contacts should be closed to the car body. If there is no voltage indicator on the device, then this is exactly the wire that we need.
Once you have found the necessary wire, it should be insulated. This must be done so as not to accidentally burn out the car's wiring. You still have cables in your hands that need to be connected to each other to start the car. After the engine has started, you will also have to insulate the starter wire. This action is necessary so that while driving the starter does not start turning on its own.
Please note that each of the steps described above should be performed with the utmost care. The fact is that any mistake easily damages sensors and wiring, which leads to large-scale problems
By the way, if your car has an on-board computer, then it is better not to resort to using this method.
Correct wire connection
When all the wires have been found, all that remains is to connect them correctly and start the car. To do this, you should perform the following steps:
- Leave the ground and starter wires unconnected;
- connect the remaining wires responsible for powering various car systems to the power cable;
- connect the starter wire to the power supply and wait until the car starts;
- As soon as the engine starts, remove the starter wire from the group of live wires;
- You will receive at your disposal a running vehicle with working systems for transportation.
Remember that you need to connect the power wires securely enough. On the way, the contact may weaken and you will be left without a headlight, for example. After transporting the car, immediately begin repairing it and bringing it back to normal condition.
How to get into the salon if the door key is also lost
For the first method, you will need about half a meter of thin steel (1-2 millimeters) wire. Make a rounded hook at one end of the segment and bend it at the other so that the improvised tool does not accidentally fall into the empty space of the door. Next, do this:
How to remove the ignition switch on a classic
pull out the glass seal located at its base from the driver’s seat; Insert the hook into the opened slot; carefully move it under the lock drive; hook and pull up; The button comes out easily. If you have a metal ruler, that will also work (we don’t recommend using a plastic one - it will most likely break)
First of all, remove the seal. Now insert the plate strictly into the center of the glass - it should ideally rest against the lock rod. Press the door harder - lean on it to make it easier for the tongue to come out of the groove. Press down on the rod and, as soon as you hear a click, pull the handle towards you
If you have a metal ruler, that will also work (we don’t recommend using a plastic one - it will most likely break). First of all, remove the seal. Now insert the plate strictly into the center of the glass - it should ideally rest against the lock rod. Press the door harder - lean on it to make it easier for the tongue to come out of the groove. Press down on the rod and, as soon as you hear a click, pull the handle towards you.
When there is neither wire nor a ruler, then use the following method - take a piece of twine or, for example, a lace from a shoe. Keep in mind that this option is only suitable when the locking buttons on the machine are mushroom-shaped.
At the end of the rope, make a tightening loop with a diameter of 4-5 centimeters. After that:
press the door away from the opening (only on top, in the right corner); insert a string into the gap formed; carefully place the loop on the button; slowly lower your end so that the rope is perpendicular to the door; tighten the loop; lift the twine up and pull. The disadvantage of the latter method is that you will have to repair the damaged door
The disadvantage of the latter method is that you will have to repair the damaged door.
How to start a car without a key VAZ 2114
How to start a VAZ 2114 without a key: necessity and solutions
There are various unexpected situations in his life and when we lose our car keys. According to the law of the falling sandwich, in most cases this happens in the lap of nature or in the country. How to solve this problem? What will they do and how to get the keyless key 2114? There are several ways to access the vehicle's power source and how to connect it.
Torque
You will need a Phillips screwdriver and a paperclip (a piece of wire) to tighten it.
Open the cover and disconnect the wire from the positive terminal of the battery. Place the gear shift lever in neutral. Put the car on the parking brake. Using a Phillips screwdriver, remove the control column cover and reinstall it. FROM Ignition switch Carefully remove the unit from the wires. Immediately determine which wire is ground and disconnect it from the others
If the ground is covered by the multimeter on the case, there will be no voltage. It's even better if you insulate the cable, as long as you haven't broken all the wiring. Find the reddish wire and move it to the side. Carefully connect the remaining wires so that they are in contact. Secure the scroll with wire, in other words, a paper clip. From time to time the twist is rewound with tape or tape. Your machine's electrical equipment must be turned on. Squeeze the clutch pedal. Lay the reddish wire on top of the other wires (twist). We need to start the car. Remove the red wire from the turn. If engine speed is measured, release the clutch pedal carefully and carefully.
Connectors (pads) Ignition switch
different cars on different cars. There are types of connectors from which you can disconnect the wires with an awl. Only after removal are they twisted together (without the reddish wire).
how to make a VAZ 2114 without keys
how to make a VAZ 2114 without keys
, wires, like in American films. Remember that almost all locks have blocks, of course.
AS A TEST TASK VAZ 2115 2114 2113 WITHOUT KEYS
Hello everyone =) In this video I will show you an easy way to start a car engine.
After starting the engine, the red wire is immediately removed from the turn. Otherwise, the starter may break.
Warning! If you do not disconnect the wire from the battery terminal when the wires are twisted, the engine will start and a short circuit will occur.
Drilling Ignition Switch
Drill the ignition switch so that the drill bit is slightly higher than the keyhole. This will destroy the locking pins. Repeat the operation several times and fall apart later in the castle. narrow screwdriver. The machine should start.
The ignition switch must be replaced after drilling. Some models will cost more than calling a tow truck.
Direct battery charge
Additional method how to get 2114
deserted. Connect the ignition coil wire (under the cover to the lower part relative to the center) and the positive battery. The ignition must be turned on. From the starter terminal, connect the wire to the battery plus, the starter should be energized and the engine should be running.
Using a metal plate
A plate similar in size to the iron part of the ignition key is inserted into the ignition switch. The extended part of the plate is forcibly turned with a screwdriver, like a lever, to break the lock. The record rotates in approximately the same direction as the key. After turning the plate the machine
we need to start.
In addition to troubleshooting starting problems, you will have to remove the steering lock by making sharp turns from the last right to the last left and back.
To remove the car from the alarm, you need to set the alarm button to wallet mode.
The most common non-destructive method and subsequent repair is to power the battery directly from the ignition coil and starter battery.
A malfunction of the power supply leads to wear and tear on sensors and electrical equipment.
If the car has a fender, so that it does not burn out, it is better not to start it this way, but to call a repairman or a tow truck.
Finally
To make the right decision, you must use the following methods to start the machine, you need to calculate and compare the damage caused by the loss of time and repair costs that will have to be carried out after an emergency start.
Source
Post Views: 10
Removing the immobilizer control unit
1. Remove the negative terminal of the battery.
2. Remove the instrument panel trim.
3. Using a Phillips screwdriver, unscrew the two screws securing the unit to the instrument panel, holding the screw nuts with a 10 mm wrench.
4. Remove the block from the instrument panel and disconnect the harness block
Removing the remote control unit
Raise the rear seat cushion. Loosen the screws securing the carpet in the rear left door opening.
3. Having folded back the edge of the carpet and the sound insulation, disconnect the wiring block from the remote control unit.
Is it possible to start a car without a battery?
There is no clear answer to this question. Modern cars equipped with injection systems are unlikely to be able to start without a battery. Such engines use electric fuel pumps, electronic control units, and piezo injectors, which require an electrical power source to operate. To start the generator, an excitation voltage is also required.
With a high probability, the generator will start working during towing due to self-excitation, but the absence of a battery as a buffer element in the on-board electrical network significantly increases the risk of electronic failure and formally operation without a battery is prohibited. It is relatively safe to try to start old carburetor cars, and then electricity is needed to operate the ignition and open the carburetor solenoid valve.
In any case, you can only try to start cars with a manual transmission without a battery.
How to start a car if the battery is dead: video
6 ways to start your car if the battery is dead
You cannot start the injector without a battery, because there is an electric fuel supply pump to the system, the electric brains see that there is no fuel pressure, which means there will be a ban on igniting the fuel.
If the car is old with a mechanical fuel supply pump, then it is possible to start the car with a pusher. To do this, you must first pump up the fuel, then accelerate the car to the speed so that the generator provides enough energy to ignite the fuel. It should be noted that when the engine is running without a battery, the generator is capable of producing more than 16 volts, and this can cause light bulbs to burn out (this is in the best case) on the car. And on the injector there is a high probability of burning out the brains (control unit). It’s better to ask someone for the battery or buy a new one.
"Light up" the car
The second option is to have someone “light” the car by transferring current from one battery to another. In this case, you will need to connect the “lighting” wires using terminals (“crocodile clips”) directly to the “active” and dead car battery. In general, if the question arises about how to properly charge a battery when its charge is low, then this method may come in handy. But when there are no other cars nearby or no one wants to help, it will be problematic to use this emergency start option.
Source
How to start a VAZ 2107 without an ignition switch
How to start a VAZ 2107 without an ignition switch
Guys, this situation has been working for 3 days already, I arrived and started to start the car, but it won’t start (it’s just raining outside), what should I do in such cases at the beginning. I'm just new) VAZ 2107 Car (2000)
Andrey (Peddir) Dmitry, see electricity (trombler) and much more.
Gasoline Mika (Ashley) checks it out early
Sergey (Proserpina), if bsz switch checks me for 3.2, it’s worth it, I stupidly change the chip and everything else is lost
The experts (Jolain) migrated. Misha Necheporenko Men tell me about the problem with the injector of the 7th 2006: it starts very hard, if it starts, the engine melts for about 3.2 seconds to melt.
Alex (Ravenna) Mika, do you still have diagnostic points for our client, have you decided to start your own engine? check additionally https://car-exotic.com/vaz-cars/vaz-lada-2107-diagnost. Cancel subscription.
Mika (Ashley) Alexey, In short, they got the key in their brain; They purchased a new ignition module for the armor wire spark plugs which is still to be done for our customer, the kit works reliably.
Sergey (Proserpin) started on the 1st try in the morning, but not very well, since two people started on the 2nd try. What is the reason
Alexey (Ravenna) Sergey, it’s getting colder. As far as carbohydrates go, I don't think it's a problem. From time to time and from the third with me.
Sergey (Proserpine) Alex, thank you
Alex (Ravenna) Checking the starter via the ignition switch and starter relay (situation does not engage the starter) 1. Transmission in neutral, vehicle on parking brake. 3.5. Open the wire connection to the electromagnetic relay (1 contact in the right mudguard) 3. Prepare a wire about 0.5-1 m long. 4. Key to ignition position 5. Close the plug from the battery electromagnetic relay. If the starter starts. find the problem in the lock, starter relay, no voltage on the starter relay. In cold weather, ask someone to help push the clutch. If you are broken down for repairs, this is an option, then run the engine for a long time. The only time to start is winter. Prepare a wooden block and press the clutch pedal. the device rests on the driver's seat.
Alex (Ravenna) Situation does not start starter hot Wire and weight connections are tight to starter. Because the contacts deteriorate when heated. In particularly advanced cases, the wiring terminals are turned off and then tightened and suppressed.
Alexey (Ravenna) If the two previous situations have been developed, however, there is still no place for the starter. The starter was removed from the car engine and repaired. In other words, it may change if the repair fails (critical wear)
Pavel (Bhavin) Can't it start if there is no mass?
Alex (Ravenna) Pavel, even if there is no plus.
Pavel (Bhavin) Alexey, and this is understandable. The terminal is just warming up, they said there is no mass. So what to do? Cleaning something, or what is it called looking, and maybe something went wrong in some places?
Alex (Ravenna) Paul, this is a lover. Some people just hang out on the Internet. those. discussions are more important than the car ride and, finally, takeoff and delay.
Anton (Ladislao) Paul, I ran to the store, bought two lead terminals (great, damn), put them on and voila, it doesn't heat up and the contact is better. Terminals cost pennies, 15 rubles apiece, and can be changed in 10 minutes.
Comments on the manual
Brown 04/06/2011
Oh, what good advice, of course not for hijackers, but for those who experienced force majeure)). In films, often, especially in chase scenes, the main characters often start cars in this way. But this happened to my friends at their dacha, when a drunk neighbor dropped his keys into the well, and they had to go. But they did not know such advice, so they had to wait a long time for help.
Ivanov 04/06/2011
And I know how to do this, my father taught me. It was very cool, but a little scary. What if it hits you with electricity? But everything always worked out well, I often boasted to the guys about my skills. But with guidance, anyone can do it.
Nik 04/06/2011
It's that simple. My brother started the car like this when he was 10 years old, nothing complicated. But I don’t recommend repeating this to girls; after all, working with electricity is not for girls. But they should know that in extreme cases this method can be used.
Sweetie 03/28/2012
Still, working with electricity is not for girls - what kind of chauvinism is this? Any job for girls, if the girl has enough brains. Well, maybe, except for unloading cars with coal, and then only because of low productivity%)))))
Source
How to start a VAZ 2107 without a key?
Wires. I just don’t see the point, the steering wheel will still be locked. Timofey
Hm. and how to unlock it! and what wires? Tania
The steering column needs to be replaced. There are several wires there, without experience you can burn the car. Timofey
Of course, I wouldn’t want to burn it down, but I really need to start one))) Tania
Neighbor.Bogdanchik
Locking the steering wheel will not allow you to drive away. Delight
no problem, all you have to do is open the door and roll up the stopper in the steering column
There is a key to the door))) You just need to know where this stopper is and what wires to connect)))) can you tell me? Tania
you need to open the door and roll the stopper in the steering column and then close the wiresAleko
There is a key to the door))) You just need to know where this stopper is and what wires to connect)))) can you tell me? Tania
Remove the plastic steering wheel, dive under the steering wheel with a flashlight, carefully remove the retaining ring of the contact ring and use the reverse gear. Locking the steering wheel is a separate issue. Removing the lock without a key is bad - you can turn it over 15 degrees - you can't pull the lock out of the tongue. Yes, be careful not to close the contacts with the retaining ring. The main power + seems to be going red. Try to poke one at a time towards the red one. The ignition lights came on, and the starter was briefly poked and removed. Ignition - don't turn it off - the coil may overheat if the breaker contacts are closed. Below they write pink - maybe the main one and pink - you need to look at the diagram, Captain
A month ago I lost the keys to my Niva (everything is the same as on 07). I removed the retaining ring of the ignition switch and took out the contact block (I twist it with my hands instead of a key), pulled off the steering wheel locking tab with a screwdriver and secured it with a self-tapping screw. This is how I drive now. Vala
you open the car with a ruler, connect the pink and blue with the black stripe permanently, the ignition will appear, connect the red to the pink and the starter will appear. if the car is carburetor: open the hood, connect the battery with the ignition coil (pin B), insert a screwdriver into the starter and off you go))) Elana
how to remove the starter on a vaz 21072? I need instructions for the kettle
There is no power from the ignition switch to the starter. What could be the reason? VAZ-21072
VAZ 11193 "KALINA". The battery died and after replacement it will not start. no indica ENGINE, starter does not turn, fuses are intact
how to open the hood if the cable comes off on a VAZ 11193 (Kalina) please help
VAZ 1119 Kalina engine 1, 4 16V if the timing belt breaks, does it bend the valve?
Opening a car using a ruler
It is not always possible to use a spare set of keys and an alarm remote control, so it is recommended to open the car using improvised means. If you don’t have any tools at hand other than a metal ruler, then you shouldn’t despair, because with the help of this ruler you can open the car. This method is as follows: go to the driver’s door and lift the side seal near the lock. Then insert a ruler into the gap between the glass and the door and press it onto the rod responsible for raising the flag. It should be understood that some models of modern cars are equipped with reliable door mechanisms, so it will not be possible to press the rod using a ruler. Manufacturers of such cars provide protection for the door mechanism and attempts to open the door with improvised means will be in vain. However, most cars, including models of the domestic auto industry and many foreign cars, can be opened in a similar way.
When you don't want to bother
If you realize that the described options cannot be implemented on your own, then you should seek help from specialists. Now in any city there are companies providing lock picking services. This is the optimal solution if the standard key was simply forgotten inside the vehicle.
It should not be ruled out that calling a professional will cost less than eliminating the consequences of your inept actions. A specialist is able to open the car without leaving the slightest scratch on it.
Keep in mind that you will have to document that the car belongs to you.
The second option is to call a tow truck. This will have to be done if a chip key is needed to open (start) the car. Replacing the latter involves installing a new core, and this is difficult to do outside a service station.
In the described situation, access to the interior or starting the engine is a secondary task, which can be solved without any problems in a car repair shop.
how to start a Lada without a key
How to start a Lada without keys
In the Service, Maintenance, Tuning section, the question is how to start a VAZ or Lada without a key? How to start a VAZ or Lada without a key? asked by the author Serega pavlov the best answer is a Classic if: You remove the plastic from the steering column, take out the retaining ring at the back of the ignition switch and the contact block with wires will fall out, and then use a screwdriver to start it like a key, only the steering wheel remains locked)) ) If you like in American films pull out the wiring, then study the electrical diagram, I just don’t remember the color. There you need to close the power then the starter, and don’t forget to connect the power supply to the wiring that is responsible for charging the battery
Reply from 2 replies
Hello! Here is a selection of topics with answers to your question: how to start a VAZ or Lada without a key? How to start a VAZ or Lada without a key?
Answer from Dimon Miroshkinhacker magazine must be read (c)
Answer from Jack Daniel using crowbar and wiring
Answer from TheSimple: you pull out the ignition, rip out all the wires and then connect two wires of different colors, it turns out the same thing as using a key, only what color of the wires I forgot, there are only five of them, but you can look it up on the internet if you like.
The answer from Dmitriy Chesalin is very simple - disassemble the ignition switch and look at the terminals - what connects to what and connect it. I started it like that myself when the contact in the lock was covered in the middle of the road
Answer from Ѐuslan what model? if it’s a classic, then you take out the retaining ring from the ignition switch and the contact group falls out, just turn it and that’s it, but if it’s the tenth family, then just use the side lights switch, just move the chip and the ignition will light up, just push it in gear and it’ll start
Answer from Mihon-nLook here
Reply from QSwitch Sorry for being off topic, but I still warn you about Articles 158 and 166 of the Criminal Code.
Answer from Igor Rimachenkov: You pull out all the wires near the ignition switch and connect) ) it’s elementary, but it’s more difficult to break the steering lock.
Starting a Lada engine without a starter
If the starter does not work or the battery is dead, then you can start the Lada with a pusher or with a crooked starter. We will consider each method in detail separately.
How to start with a pushrod
You can push the car yourself on a flat road, but you will need certain equipment there; it is better to act if there is a hill/slope.
You can start a Zhiguli with a discharged battery from a pusher in this way:
- Turn on the ignition.
- Pump gasoline into the carburetor using a fuel pump.
- Pull the choke out a little to enrich the mixture.
- Engage neutral and roll the car onto a flat, straight section.
- Position yourself near the open driver's door, grab the pillar and accelerate the car to a speed of about 10 km/h.
- When the speed is up, jump into the seat, press the clutch and gas, engage second gear (the first quickly reduces speed due to the high frequency of movement of the pistons).
- As soon as the engine starts to catch, “play” with the clutch, pressing and releasing, so that it begins to work stably.
If you have an assistant or another machine, everything is easier. Enough:
- Hang on to the cable or ask an assistant to push and sit behind the wheel.
- When the towing vehicle or assistant picks up speed, press the clutch and engage the gear.
- As soon as the engine starts, press the clutch and put it in neutral again, stop (if a person is pushing) or give a stop signal to the towing person and also stop behind him.
If there is a good slope, you can simply roll the car onto it so that it rolls down, immediately get behind the wheel and start driving.
Starting the engine manually
Another way to start a Zhiguli if the starter does not work is to start from a “crooked” position. This way you can start old VAZs of the classic family that have a manual starter function (there is a hole in the crankshaft pulley and in the bumper). To start a VAZ with a crooked starter, you need:
- Ignition switch pinout for VAZ 2109 injector. 2101-2107-2109-2110
Starting a VAZ from a crooked starter
- Set the gear to neutral.
- Turn on the ignition.
- Open the choke.
- Pump gasoline into the carburetor.
- Insert curved starter.
- Take the pen so that all fingers are on one side (the thumb is with the rest, and not opposite).
- Turn the handle until it starts (from top to bottom clockwise).
You need to keep your fingers together so that in the event of a reverse flash (if the spark passes early and the shaft moves in the wrong direction) or the engagement mechanism jams, you do not get injured.
A useful recommendation from the owner of a VAZ 2101: after pumping up gasoline with a gas pump, first turn it slowly 5 times, then get into the car and pull out the choke. Depress the gas pedal 10 times and turn on the ignition. Then set the starter knob to the “5 o’clock” position and sharply turn the knob clockwise. The engine will be able to start the second or third time. You need to scroll with gloves or a wrapped rag. Don’t try to use it like a sewing machine—one sharp tug is all it takes. Be careful not only with the placement of your fingers on the handle, but also so that after starting you do not puncture the radiator. The end of the curve flies off the ratchet and it’s very easy to throw it somewhere to the side!
How can you tell if this is possible?
If your car has a manual transmission, then before pushing the car in hopes of starting the engine, you need to rule out other faults. If, when you try to start the engine, the starter engages but does not start, then there is no point in pushing the car. Here there is another malfunction, for example, such as a lack of gasoline in the fuel tank, various breakdowns in the engine itself (broken timing belt, etc.). In this case, you should not waste time, but it is better to immediately contact a car workshop. In this case, the car can be towed using a cable (“tie”).
Knowing how to drive a VAZ-2114 car can be useful to any car owner. The situation when you stop on the road for 5-10 minutes and can no longer start the car is very unpleasant. ! What to do in such a situation? This is when knowledge of how to “short-circuit” the starter to start the car can come in handy.
Helpful Tips and Warnings
When undertaking this type of installation work, be prepared for unforeseen circumstances. Use the above methods only in extreme cases, since almost all of them lead to irreversible changes in the design of the car, which can only be eliminated through repair work. In case of incorrect actions, the car may be damaged to such an extent that even specialists cannot eliminate it.
After starting the engine, never leave the ignition wires twisted. Because of this, the engine ignition system can be severely damaged and the battery discharged. For most cars, if the car is started incorrectly without a key, the alarm will be activated. And car models with a computer chip in the ignition switch will not start without a key, because it controls the operation of the electronic control module. This module is directly responsible for starting the engine.
If the ignition wires are disconnected while driving, the engine stops instantly and the car may be de-energized (read about how to replace the ignition switch contact group). The steering and brakes may also fail, so do not allow the wires to become disconnected. To avoid electric shock, use dielectric gloves. But even with these gloves, you should not touch the exposed contacts.
Reasons and signs that the key is stuck in the ignition switch
The most common causes of ignition switch failure:
- an attempt to start the car with a non-standard key or a thief's tool;
- moisture entering the lock cylinder at subzero temperatures;
- hardening of the lock lubricant;
- damage to the key geometry (bending, damage to grooves and protrusions);
- wear or breakage of the cylinder;
- Damage to the lock body at the time of an accident.
The first signs of an impending malfunction are:
- slight jamming of the key when inserted into the ignition;
- jamming when trying to turn the key to the first position;
- inadequate operation when turning on the ignition and starting the engine;
- extraneous mechanical noise, crackling, grinding when turning the key.
When the first signs of a malfunction appear, you must immediately begin to fix the problem, do not wait until the key gets stuck in the ignition switch.
The fact is that to repair the lock it is necessary to remove the ignition lock cylinder: it is precisely because of its malfunction that in most cases the key does not turn.
The designs of lock cylinders are different for all car brands. The general principle is the extraction and replacement of larvae.
In order to remove the cylinder from the lock base, you need to turn the key inserted into it to the first position, then press the latch (pin) to ensure its removal.
If the key does not turn to the first position, the process of removing the cylinder will be very difficult, if possible without any drastic mechanical influences. In such cases, if by some miracle you manage to turn the key and start the car after turning it off, you should under no circumstances remove the key. It is necessary to leave it in the lock in the first position and immediately begin to fix the problem.
Lada Kalina: changing the standard key to a flip key
FakeHeader
Comments 8
Please tell me how the standard immobilizer and engine autostart behave after installing this system?
There are no changes in the operation of the immobilizer, since this button is connected to the standard connector of a conventional ignition switch and only performs its function. As for autostart, you need to look at the connection diagram. But since most alarms are connected to the key, the auto start will not see this button. The button simply emits the operation of the key in the ignition switch. But there are a number of disadvantages: the car cannot start from the pusher)) and when the battery is very discharged, the button block takes on a charge and the car does not envy without lighting it.
Dismantling the lock cylinder
Before starting this procedure, you need to “read” on the Internet recommendations for replacing the cylinder specifically for your car model, since there are thousands of possible options. It is possible that you will have to drill a hole in the lock structure, for example, as in GOLF 3.
Or AUDI.
In some cases, it is necessary to make “special tools”.
Repair of the lock cylinder
To carry out repairs, it is necessary to disassemble the larva. Its design can be complex, such as in BMW.
If you look closely, you can see that each element of the comb is signed with a two-digit code. We sell repair kits for lock cylinders of different car models. The main choice of repair option is faced by the car owner and the specific situation.
If you have three or four good keys for the car, it is better to purchase a repair kit and “reassemble” the cylinder. Anyone can do this, even without special knowledge. The comb elements are sequentially inserted, starting from the first, and the key is inserted into the cylinder until the metal parts protrude from the cylinder. The element number is recorded. The procedure then continues for the next positions of the larva. The selection is lengthy, but overall the process is creative and entertaining.
There is a simpler and faster repair option. To do this, you need to insert the key into the cylinder along with all the filling and cut off everything that protrudes beyond its limits with an emery wheel. Check for protrusions when installing other keys. Fast, but this option reduces the car’s security against theft.
If your car only comes with one or two keys, it may be cheaper to buy a new key. Then you will have to reinstall the immobilizer chip in the new keys that come with the cylinder. It is necessary to disassemble the new keys and check if they have the necessary cavities to accommodate the chip. If the original keys contain electronics and buttons, this option will not work at all. There may be an option to replace only the metal part of the key.
Towing a gazelle
The third method is to tow a car with a dead battery. To do this, you will need a third-party car that will drag (tow) the gazelle by the cable until its engine starts. This method is similar to pushing a car, but it is more effective.
Important! Drivers of both vehicles must exercise caution when towing. Braking should be safe for the car in front, and at the same time, the vehicle attached to the cable should not be completely “turned off” when performing a stopping maneuver.
How to start VAZ 2106, VAZ 2109, VAZ 2110 and VAZ 2112 without a key
In the case of a VAZ 2106 car, you need to remove the ignition cover and find the brown, blue and red wires. The thick red wire is positive. The brown and blue wires need to be secured with electrical tape, and the red wires should be struck on both wires. The car should start. A similar procedure can be done for the VAZ 2109.
To start a VAZ 2110 or 2112 car without a key, you will need to pull out the entire headlight switch so that it dangles on the wires and remove the cover: there will be four connectors. Now you need to insert it differently - into three connectors so that there is one free on the right. At the same time, the fuel pump will start working and the ignition will turn on. Now open the hood. It is necessary to force the starter to start, for which it is enough to bridge the copper bolts, which are located in the back cover of the starter solenoid relay, with a wrench or scissors. The car started.
You can clearly see how to not only start, but also open a “ten” or “two” without a key in the following video:
how to open a VAZ 2110 without a key and start it
Now you know how to start a car without a key. Of course, a considerable number of cars of foreign expensive brands are already equipped with factory buttons and special key fobs; you can often find code panels for entering a PIN code. As for domestic cars, such an easy opportunity to start a car without a key should be alarming - do not leave the car unattended and without an alarm.
Read about opening a car without a key here. Well, if you are upset about losing your keys, read our instructions for this case.
